ASO-STM100
ORIGINAL
使用說明書與零件圖
INSTRUCTIONS BOOK & PARTS LIST
For the sewing machine, automatic mechanic system, and auxiliary devices
(hereinafter referred as “machine＂), it is inevitable to conduct work near
moving parts of the machine. This means that there is always a potential
risk from the moving parts. Operators actually operating the machine and
service technicians performing maintenance and repair are strongly advised
to read and understand fully the following instructions in advance.
The safety instructions include items which are not listed in the
specifications of your product. It is the manager/supervisor´s responsibility
to have their fellow workers fully understand before operation.
Fail to follow the instructions may cause damage to properties, severe
injure or even death.
Explanation of warning indications and labels.
有關於縫紉機，自動化機構，以及其他輔助設備（以下統
稱為機器），在工作中無可避免會接近機器移動區域，也
就有伴隨著潛在風險。因此，我們強烈要求操作者，維修
技師一定要先仔細閱讀並瞭解本操作手冊的內容。
安全指示係包含了某些未載於規格書上的加裝配件。
現場管理者有責任要求所有操作者要閱讀並瞭解機器的操
作與注意事項。
未能確實遵守本手冊所記載的事項，將可能導致機器的損
害，或是人員的傷亡。
警告標示說明
安全警示 GENERAL SAFETY INSTRUCTION
高壓電危險
在機器關機後十分鐘內，勿開啟電控箱。
HIGH VOLTAGE DANGER
Do not open the power cabinet within 10
minutes after the power off.
零部件移動區
勿接近，以避免人
員受傷。
Machine moving
area!
Stay away and keep
clear to avoid injury.
零部件高速移動區
勿接近，以避免人員受傷。
High speed moving area!
Stay away and keep clear to avoid injury.
CAUTION
機械作動部份請注意裝上
保護裝置
穿線、換線、調整、清潔
時請注意關閉電源.
Moving parts may cause in jury.
Operate with safety devices.
Turn off main switch before
threading, changing bobbin and
needle, cleaning etc.
請儘快下載 SIRUBA APP，並將您的機器註冊，以便獲得原廠的保固。APP 還提供多項有用
的資訊。
please register your Siruba machine online or through Siruba App at once, as to gain the full
warranty protection. You may also acquire more useful information through Siruba APP.
溫馨提醒 A WARM REMINDER
Apple Store
APP
Google Play
APP
標告標示說明 WARNING LABELS 標告標示說明 WARNING LABELS
機器零部件移動區，勿接近，以避免人員損傷。
A risk of cut and injury from moving parts. Stay
away and keep clear.
請注意，在操作過程中握住縫紉機會傷到您的
手。
Be aware that holding the sewing machine
during operation can hurt your hands.
有電，危險。
A risk of electric shock. Stay away and keep
clear.
小心被機械捲件受傷！
There is a risk of entanglement in the belt
resulting in injury.
高溫度區！危險，勿靠近。
A risk of burn from the high temperature area.
Stay away and keep clear.
如果觸摸按鈕托架，可能會造成人身傷害。
There is a risk of injury if you touch the button
carrier.
強光！勿直視，以避免眼睛受傷。
Avoid direct eye contact with the laser beam or
other light source.
一般安全標示 GENERAL SAFETY INDICATIONS
機器運行方向
The correct direction is indicated.
小心頭部撞擊！
A risk of injury to head from upper contact.
Apply proper protection (helmet) and keep clear.
電氣接地位置標示
Grounding connection as indicated.
危險
意外事件將會導致人員受傷甚至死亡，也會造成財產的損害。
當有必要進行電控系統的檢修時，務必要關閉電源，並等候至少
５分鐘以上才能打開電控箱／操作箱，以避免電擊。
注意
1. 基本預防
(1) 在操作前務必先閱讀操作手冊與其他機器電件的說明書，
請妥善保存操作手冊與說明書以便隨時查閱。
(2) 這些注意措施包含了機器上加裝，但未列在規格書上的項
目。
(3) 務必要戴護目鏡與手套，以避免破損零件所帶來的傷害。
(4) 有裝戴心臟調節器的人員，請先詢問醫護人員有關注意事
項。.
2. 安全裝置與警告標示
(1) 操作前要檢查 ,並確認所有的安全設施有妥善安裝且運作正
常。
(2) 若安全設施因維修需要有移動，在機器重新啟動操作前，
請確認安全設施有重新安裝回原位，並且運作正常。
(3) 機器上的安全警告標示要保持完整與可辨視。如果有污損
或遺失，請儘以更新。
(4) 未能確實遵守安全規範，將會導致人員受傷，甚至影響生
命安全。
3. 應用與修改
(1) 嚴格禁止機器使用在非原始設計用途。也禁止以任何不是
操作手冊上記載的方式來操作機器 .
(2) 嚴格禁止修改機器。任何未經原廠許可的變動將不在保固
範圍內。
(3) 機台一經修改變動，本公司將不擔負財務損失，人員傷亡
的責任。
4. 教育與訓練
(1) 工廠主管人員有義務提供機台使用人（操作者／維修者）
相關的教育訓練。良好的教育訓練不僅可以避免造成人員
傷害，也可以避免財產的損失。
(2) 操作人員操作機器之前，都必需接受過良好的訓練。
(3) 機器的維修保養必須由合格的技師執行。
5. 必須關閉電源的情況：
如何關閉電源：按壓下緊急停止開關（如果機器有配置的
話），關閉電源，拔除電源線。
(1) 當機器出現異常時，按下緊急停止開關（如果有配置），
關閉電源。
(2) 為了避免機器突然起動造成意外，在操作機器前，要先確
定機器電源關閉，再行開啟電源。
(3) 當檢查或清潔機器時，關閉電源，並確定機器已完全停止
運作。
(4) 當維修機器時（如更換或調整零件），要關閉電源，並確
定機器已完全停止運作。
6. 拔除電源線時，務必要抓住電源插頭，而非抓住電源線，以避
免斷裂，電擊，甚至火災。
7. 當機器停止運作，且無人看管時，要關閉電源。
8. 萬一停電或電力供應出現不穩，關閉電源，以避免意外發生。
安全須知 SAFETY PRECAUTIONS
Danger
An accident means ＂to cause personal injury or death, or damage
to property. ＂
When it is necessary to perform service on electrical parts, be sure to
turn the power off and wait for 5 minutes or more before opening the
power cabinet/box in order to avoid electrical shock.
Caution
1. Basic precaution
(1) Read the manual and other papers supplied with accessories
of the machine before operation. Keep the manual and papers
at hand for quick reference.
(2) The content of this section includes items which are not listed in
the specification of your product.
(3) Always wear safety goggles and gloves to avoid accident
caused by parts breakage.
(4) For those who use a heart pacer, please consult the medical
specialist first.
2. Safety devices and warning labels
(1) Check to ensure all safety devices are correctly installed in
place and properly before operation.
(2) If any of the safety devices is removed for service cause, please
be sure to replace it back to position and verify that is works
normally before resuming operation.
(3) Always keep the warning labels adhered on the machine clearly
visible. If any of the labels missing or contaminated, replace
with a new one at soon.
(4) Fail to obey instructions above may cause severe injury or
death to the operators.
3. Application and modification
(1) It is prohibited to use the machine for any application other than
its original intention, or in any manner other than that prescribed
in the instruction manual.
(2) Never modify or alter the machine. Any unauthorized change of
the specification will not be covered by the warranty.
(3) Our company assumes no responsibility/liability to damages,
injuries, or death resulting from the machine which has been
modified or altered.
4. Education and training
(1) The plant managers/supervisors are obliged to provide
education and training to operators and service technicians. A
good education/training plan not only avoids personal injury but
also prevent damage to the property.
(2) Only a well-trained operator is allowed to operate the machine.
(3) Only a certified technician is allowed to perform service to the
machine.
5. Situations that you must turn off the power
Turning off the power: press EMG Stop (if there is one), switch
off the power, and remove the power plug from the outlet.
(1) When there is a failure or abnormality, press EMG Stop (if there
is one), switch off the power.
(2) To prevent accident resulting from abrupt start of the machine,
before operating the machine, always turn off the power and
switch on again.
(3) When cleaning or inspecting the machine, make sure the
machine stops completely after turning off the power.
(4) When performing service (i.e. changing of adjusting any
component), make sure the power is off and the machine stops
completely.
6. Remove the power plug by holding the plug section instead of the
cord to avoid electrical shock, leakage, or fire accident.
7. Turn off the power whenever the machine is left unattended
between works.
8. In case of a power failure or black out, turn off the power to avoid
damage or accident.
1. 運輸
(1) 當搬運或移動機器時，請考量機器重量，選擇安全合適的
方式。請參考機器規格。
(2) 採取足夠的安全防護，以避免機台在搬運或移動中掉落。
(3) 為避免意外，運送時不要重覆使用包裝材料。
2. 拆箱
(1) 在拆箱前，檢查機器是否平穩放置，並採用適當的工具維
持拆箱過程的穩定。
(2) 進行拆箱時，遵循外箱上的指示，小心外箱上的釘子或碎
片。
3. 安裝 :
3A. 桌板與腳架
(1) 採用原廠的桌板以確保機器得到足夠的保護與支撐。如果
在安裝或維修時，需要暫時將機器置放於物件上，請確定
該物件有足夠的支撐力。
(2) 如果桌板有裝置滾輪，滾輪需要有煞車鎖定機構，而且在
操作與維修時，煞車機構必需鎖定。
3B. 電線與管路
(1) 電線與管路的材質必需符合規範與需求。.
(2) 電線與管路不能夠有折彎或壓迫。移動的零配件上，電線
與管路需有至少 30mm 以上的預留量 .
(3) 接線時不能有跳火。
(4) 所有接頭都必需要確實固定。當拆除時，務必要抓住接頭
本體。
3C. 接地
(1) 接地是必需的。且需由合格的技師來施工。
(2) 在操作前需確認接地有確實。
3D. 馬達
(1) 馬達的選用，必需符合規範與需求。
(2) 如果馬達為皮帶傳動，務必要安裝保護措施以避免捲入危
險。
4. 在開始操作前
(1) 在開啟電源前，確認所有接頭，電線，管路都完好無損，
確實連結。
(2) 檢查皮帶輪的轉向與標示為同一方向。
(3) 確認腳架滾輪都已鎖定。
(4) 保持作業範圍淨空。
5. 在操作中
在不同階段的注意事項 PRECAUTIONS TO BE TAKEN IN
VARIOUS OPERATION STAGES
1. Transportation
(1) When lift or move the machine, please take the machine
weight into consideration and apply a safe manner.
Refer to the specification for the information you need for
transportation.
(2) Apply sufficient safety measures when lifting or moving the
machine to avoid falling or dropping.
(3) To avoid unexpected accident, do not reuse the packing
material for transportation.
2. Unpacking
(1) Before proceeding to unpacking, check the balance of
the machine and apply necessary tools to hold the proper
position.
(2) When unpacking, follow the instruction printed on the
cartoon. Be careful of the nails and chips when unpacking
from a wooden rack.
3. Installation:
3A. Table and Stand
(1) Only adopt a qualified genuine table and stand to assure
the holding support. In case you need to leave the machine
on a surface temporarily for service, make sure the surface
is strong enough to hold the weight.
(2) If casters are applied to the table stand, adopt casters with
a locking mechanism only and lock them well to secure the
machine during the operation and service.
3B. Cable and Wire
(1) The cables and wires must comply with the specification
and requirement.
(2) The cables and wires shall be free from bending or extra
force. Reserve a free space of at least 30mm between
cables/wires and the moving parts.
(3) Do not apply starburst connection when wiring.
(4) All connectors must be fixed securely. And always hold the
connector body when removing it.
3C. Grounding
(1) Grounding is necessary and must be done by a certified
technician. (2) Check and ensure the grounding is secured
before operation.
3D. Motor
(1) The motor must comply with the specification and
requirement.
(2) If there is a belt in the motor transmission, adopt or apply a
proper protector to avoid entangling.
4. Before Operation
(1) Before turning on the power, make sure all the connectors,
cables, and wires are free from damage, dropout, or
looseness.
(2) Check and make sure the pulley rotation follows the same
direction as labels.
(3) Make sure all the stand casters are locked or fixed in
position.
(4) Keep the working area clean from obstacles.
5. During Operation
(1) Always keep your fingers, hair, or clothing away from the
moving components and moving area. Do not place your
personal belongings on the machine.
(1) 注意手，頭髮，衣服不在機件移動範圍。不要將個人物品
置放於機器上。
(2) 機器會高速運作。保持雙手遠離移動機件範圍。機器完全
停止前不要靠近。
(3) 在移動物件或重新設定機器時，注意不要被機器或零件撞
擊。
(4) 避免突然起動造成意外，在檢查或維修馬達或皮帶時，務
必關閉電源並確認機器完全停止。
(5) 機器停止時，伺服馬達是無聲的。注意要關閉電源以免突
然起動。
(6) 永遠保持電控箱的風扇與氣道淨空。
6. 潤滑
(1) 請依照說明書指示，選用合格的油脂來潤滑機件。
(2) 如果油品接觸到眼睛或身體，立即以清水沖洗。如有不適，
立即尋求醫護人員協助。
(3) 如果油品不慎進入身體，立即尋求最近的醫療協助。
7. 維修保養
(1) 只有合格的技師或工程師能夠進行維修服務，包含機器調
整與修理。只採用原廠的零件進行更換。如果採用非原廠
零件，或是因不當維修／調整所造成的傷害，本公司將不
負任何責任。
(2) 只有合格的技師或認證的工程師才能對電控系統進行維修
或保養。
(3) 當對氣動原件（如氣缸）進行維修保養時，務必先拔除風
源，並將氣體完全洩除，以避免突然啟動。
(4) 在調整或更換部件後，檢查所有螺絲是否銷固。
(5) 定期清潔是必需的。在清潔前務必先關閉電源，並確認機
台完全停止。
(6) 如果運作異常或不良，立即停止操作並關閉電源。聯絡授
權經銷商或我們公司以尋求技術協助。
(7) 當保險絲故障，立即關閉電源，找出故障原因並予以排除
後，更換同規格的新的保險絲。
(8) 定期檢查與清潔風道，電線與管路。
8. 工作環境
(1) 機器必需不用電磁波干擾。.
(2) 電源供應必需良好且穩定。電壓波動不得超過 10%。
(3) 隨時檢查空壓的壓力與品質。如果氣源不穩定，請安裝合
適器材以改善。
(4) 機器操作環境，室溫 5° C ~ 35° C, 相對濕度 35%~85%.
(5) 為了保護電子元件與安全起見，當有劇烈氣溫變化而導致
凝水時，立即關閉並拔除電源，並靜候至完全乾燥為止。
(6) 為了安全起見，當有打電或閃電時，請停止操作，關閉並
拔除電源。
(7) 勿在機器週遭使用電視或收音機，以避免干擾。
(8) 依當地法令規範，在操作中採取必要的防護。
(9) 關於包裝材料，潤滑油品，以及機器（含零配件）的丟棄，
請依各地政府法規的規範執行。
(2) The machine is designed to run at high speed. Always keep
your hands away from the moving area. Do not resume the
work cycle until the machine stops completely.
(3) Be careful not to be caught by the machine or components
when removing or resetting the machine.
(4) To avoid accident caused by abrupt start, when performing
service on the motor or belt, make sure the power is off and
the machine stops completely.
(5) A servo motor is silent as the machine stops. Be sure to
turn off the power to avoid an abrupt start. (6) Always keep
the fan and airway of the power cabinet clean from any
obstacle.
6. Lubrication
(1) Apply only qualified oil and grease onto the parts as
instructed in the manual.
(2) If the lubricant contacts your eye or body, wash it off
immediately. Consult a medical care if necessary.
(3) If the lubricant goes into your body accidentally, go to the
nearby medical care immediately.
7. Service
(1) Only a certified engineer/technician is allowed to perform
service to the machine, including adjusting and repairing.
Use only genuine parts for replacement. Our company
assumes no responsibility/liability for any accident caused
by improper repair or adjustment, or the use of any parts
other than genuine one.
(2) Only a certified technician or authorized engineer is allowed
to repair or maintenance the electric system.
(3) When performing service to air-driven parts, like an air
cylinder, first disconnect the air supply and expel the air
completely to avoid abrupt start.
(4) Check all screws and nut are fixed well after adjusting and
replacement.
(5) A periodical cleaning is necessary. Make sure the power is
off and the machine stops completely before cleaning.
(6) If the machine functions poorly or abnormally, stop the
operation and turn off the power. Contact the authorized
dealers or us to request for a technical service support.
(7) When there is a fuse failure, turn off the power, find out the
cause of the failure and apply solution to it, then replace
with a new one with the same spec.
(8) Periodically check and clean the fan airway and the cable/
wiring.
8. Working Environment
(1) The machine should be free from the affection of electro-
magnetic wave.
(2) The power supply should be in good and reliable condition,
the fluctuation of rated voltage should be less than 10%.
(3) Always check the air pressure and quality. Some extra
device might be needed if the supply is not reliable.
(4) The machine is designed to be used with ambient
temperature 5° C ~ 35° C, relative humidity 35%~85%.
(5) To protect the electronic components and for safety cause,
when there is a frost resulting from a dramatic temperature
rise, disconnect the power and wait until it dry completely.
(6) For safety cause, when there is a thundering or lightening,
stop the operation and disconnect the power supply.
(7) Do not use TV or radio nearby the machine as to avoid
interference.
(8) Apply necessary protection during operation. Follow
applicable regulations set by local administration.
(9) For disposal of packages, lubricant, and product, please
follow the applicable regulations set by local administration.
索引 INDEX 頁PAGE
規格 SPECIFICATION 1
安裝 COMPONENT ASSEMBLY DIAGRAM 2
操作說明 OPERATING INSTRUCTIONS 3
調試說明 DEBUGGING INSTRUCTIONS 4
計數器盒子參數設置 COUNTER BOX PARAMETER SETTING 6
報警說明 ALARM DESCRIPTION 7
設備日常檢查 DAILY INSPECTION OF EQUIPMENT 8
服務部分政策 SERVICE PARTS POLICY 10
零件圖 PARTS LIST 11
型號 Model ASO-STM100
適用孔眼 Applicable hole
適用帶繩 Suitable for rope
噪音 Noise <79dB
腰圍 Waistline 80-170cm
電源電壓 Power Supply Single Phase 1Φ AC200~240V 50/60Hz
消費電力 Power
Consumption 700 W ( Max )
重量 Weight 120Kg
機器尺寸 Machine
Dimensions
(W)1180×(D)580×(H)1750mm
( 含桌板、線架 With table and thread stand )
規格 SPECIFICATION
※ 選購配件 Options 鋼絲規格 ( 耗材 ) Steel wire specification (Consumables)
提供童裝版元件（選配）
TKO1
Provide children's wear
edition components
(Optional) TKO1
適用腰圍尺寸 50~90cm
最小褲腰尺寸 50cm
minimum waist size 50cm
GSO1
標準版彎彎鋼絲（大頭）
約7-8mm 孔眼
Standard edition bending
steel wire(large head)
Coping with 7-8 mm hole.
GS02
專用版折彎鋼絲（小頭）
應對 5~6mm 孔眼
Special edition
bending steel wire(Small
head) Coping with
5-6mm hole.
GS03
定製版模具鋼絲
應對特殊繩頭（塑膠、
金屬頭）
Custom edition mold
steel wire Coping with
special rope head
(plastic metal head).
P1
切口 Incision ≧ 5mm
平頭眼
flat buttom
hole
鳥眼繡
Bird's Eye
Embroidery
金屬氣眼
Metal air hole
直徑 Diameter ≧ 5mm直徑 Diameter ≧ 5mm
①Main frame
②Pantaloons
③Pedal Assembly
④Rope frame
② ①
安裝 COMPONENT ASSEMBLY
DIAGRAM
①主框架
②撐褲腰組件
③踏板組件
④繩架
③
④
P2
1.Power Up. Start
First, insert the machine's main power plug into the
socket, then turn the switch clockwise to turn the
power on. Off Means Close (right in figure) , ON
means open (left in figure) .
Press the left pedal wire out,
press the right pedal wire
retract.
1. 開機啟動：
首先將機器總電源插頭插入插座，然後順時針旋轉
開關接通電源。OFF 表示關閉（如圖右），ON 表
示打開（如圖左）。
2. 踏板操作：
(1) 電源燈亮表示有電源，滅表示無電源。
(2) 調試點動：打開維修蓋板時，按住調試點動件的
同時踩踏板，可轉動大盤。
(3) 緊急停止鍵：在緊急情況下可輕按順時針擰動，
機器在當前狀態下停止。
踩踏左踏板鋼絲伸出，踩踏右踏
板鋼絲縮回。
3. 計數器空轉盒說明：
①計數開關
②模式切換
③照明燈開關
④計數清零
⑤確認
⑥數值減
⑦數值加
3.Counter idling box description
①Counting switch
②Mode switching
③Light switch
④Count to zero
⑤Confirmed
⑥Numerical subtraction
⑦Numerical addition
操作說明 OPERATING INSTRUCTIONS
2.Pedal operation
(1) Power light indicates that there is power, no power
if it is switched off;
(2) COMMISSIONING START: When opening
the maintenance cover, press and hold the
commissioning start moving parts while stepping
on the pedal, can rotate the big plate;
(3) Emergency Stop Button: In an emergency, you
can gently press clockwise screw, the machine in
the current state of stop.
P3
①
②
③ ⑤④ ⑥ ⑦
1. 大限位調整
名詞解釋：大限位即瓦片伸開的最大位置。
按M鍵調整大限位，數值越大瓦片伸出越大。
2. 小限位的調整
名詞解釋：小限位即瓦片縮回的最小位置。
旋鬆小星型把手① ,手動推拉小星型把手，往半徑
向外則小，往半徑內則大。
3. 瓦片位置的調整
旋松此圖中兩個大星型把手①，鬆開瓦片與撐褲腰
支架的連接，然後左右旋轉底板，根據實際情況調
整瓦片位置，調整讓鋼絲順暢進出即可。
調試說明 DEBUGGING INSTRUCTIONS
1. Large limit adjustment
The maximum limit is the maximum position in
which the tiles extend. Press the M key to adjust
the maximum limit, the larger the value, the larger
the tile.
2.Small Limit Adjustment
A small limit is the minimum position in which the
tile retracts.
Loose small star-shaped handle ①, manual push
and pull small star-shaped handle, toward the radius
outward is small, toward the radius inside is big.
3. Adjustment of tile position
Loosen the two big star-shaped handle ① in this
picture, loosen the connection between the tile
and the brace of the trousers waist, then rotate the
bottom plate left and right, adjust the tile position
according to the actual situation, adjust to let the
steel wire in and out smoothly.
P4
4. Retractable limit and wire replacement
Micro switch control instructions: Extend Limit ①,
low speed limit ②, Retract Limit ③.
4. 伸縮限位及換鋼絲
微動開關控制說明：伸出限位①，低速限位②，縮
回限位③。
鋼絲出口
Wire outlet
(1) 旋松感應凸輪⑤固定螺絲，當大盤鋼絲孔運動到鋼絲擋圈
U 型槽 20-25 公分時固定感應凸輪⑤固定螺絲 .
(2) 旋松鋼絲壓板螺絲，將鋼絲從套管——U 型槽 ——大盤
鋼絲孔插入 ,置於鋼絲壓板下固定鋼絲壓板螺絲。
(3) 旋松感應凸輪③、④固定螺絲，讓大盤逆時針運動鋼絲頭
到套管口時⑤固定感應凸輪③、④固定螺絲。
(1)Loosen the fixing screw of the induction Cam ⑤ and fix the
fixing screw of the induction Cam ⑤ when the large wire
hole moves to the u-shaped groove of the wire retaining
ring 20-25 cm.
(2)Loosen wire plate screws and place the wire under the
wire plate and secure the wire plate screws by inserting the
wire from the sleeve to a type of Florida u-shaped groove.
(3)Loosen the fixing screw of the Induction Cam ③ and ④,
and let the big plate move counterclockwise from the wire
head to the casing opening. ⑤ fix the fixing screw of the
Induction Cam ③ and ④.
P5
3
3
2
4
1
5
⑤
計數器盒子參數設置 COUNTER BOX PARAMETER
SETTING
按｀´+｀´開機，參數設置 According to+Power on, parameter setting
NO.1 馬達高速 Motor high speed 2000
NO.2 馬達中速 Motor medium speed 500
NO.3 馬達低速 Motor low speed 150
NO.4 機構皮帶輪 Mechanism pulley 默認 Default
NO.5 馬達皮帶輪 Motor pulley 默認 Default
NO.6 0 雙踏板，1 單踏板 0 Double pedal,1 Single pedal 0
NO.7 計件確認時間 Counting confirmation time 5
NO.8 OFF 遮罩 E12/E14 報警 OFF Mask E12/E14 Alarm warning OFF
感測器編號 Sensor number 感測器定義 Sensor definition
Sw1/S4 鋼絲縮限位 N.C Wire shrinkage limit n.C
Sw2/S5 鋼絲縮減速 N.O Wire reduction deceleration n.O
Sw3/S6 鋼絲伸限位 N.C Wire extension limit n.C
Sw4/S11 鋼絲伸減速 N.O Wire extension deceleration n.O
Sw5/S3 撐褲腰伸限位 N.C Waist extension limit n.C
Sw6/S2 撐褲腰縮限位 N.C Support pants waist reduction limit n.C
Sw7/S1 踏板反轉開關 N.C Pedal reverse switch n.C
Sw8/S10 安全門 N.O Safety door n.O
Sw9/S8 緊急停止 N.C Emergency stop n.C
按｀´+｀´開機 Press + to turn on 參數設置 Parameter setting
按｀´M｀´開機 Press M to turn on 測試輸出 Test output
按｀´√｀´開機 Press √ to turn on 啟動程式 Start the program
按｀´LED｀´開機 Press the LED to turn on 檢測踏板電阻 Check the resistance of the pedal
按｀´C'' ''-'' 開機 Press C''''-'' to turn on 監測大盤轉速 Monitor the speed of the main disk
Sw8/S10 安全門 N.O Safety door
Sw9/S8 緊急停止 N.C Emergency stop
按｀´M｀´開機，測試輸出 Press ｀M´ to turn on and test the output
OUT1 撐褲腰伸 Waist extension 按｀´+｀´鍵 Press ｀+´ button
OUT2 撐褲腰縮 Waist shrinkage 按｀´+｀´鍵 Press ｀+´ button
OUT3 指示燈 Indicator light 按｀´+｀´鍵 Press ｀+´ button
OUT4 衣車燈 Sewing lights 按｀´+｀´鍵 Press ｀+´ button
OUT5 按｀´+｀´鍵 Press ｀+´ button
OUT6 按｀´+｀´鍵 Press ｀+´ button
P6
代碼
Code
條件
Condition
說明
Explanation
復位
Reset
E10
撐褲腰縮回時間大於撐開時間 1S
The waist retracting time is longer than the
opening time by 1S
S2 微動開關故障 /撐褲腰馬達損壞
S2 micro switch failure / damage to
the tubular extending motor
OK 鍵
OK button
E11 S3 OFF
S3 微動開關故障 /撐褲腰到達極限
位置
S3 micro switch failure / tubular
extending motor reached the limit
position
OK 鍵
OK button
E12
S5 ON + S1 OFF 大盤電機運行狀態累計 0.5S//
PS：S5 OFF + S1 ON + 大盤電機運行即清零
累計
S5 ON + S1 OFF accumulated operating status
of the big plate 0.5S//PS：S5 OFF+ S1 ON +
clearing the accumulation when the big plate is
running S5 ON + S1 OFF
S4 微動開關故障
S4 micro switch failure
OK 鍵
OK button
E13 S4 OFF + S5 OFF S5 微動開關故障
S5 micro switch failure
OK 鍵
OK button
E14
S11 ON + S1 ON 大盤電機運行狀態累計 0.5S//
PS：S11 OFF + S1 OFF + 大盤電機運行即清
零累計
S11 ON + S1 ON accumulated operating status
of the big plate 0.5S//PS：S11 OFF+ S1 OFF +
clearing the accumulation when the
is running S5 ON + S1 OFF
S6 微動開關故障
S6 micro switch failure
OK 鍵
OK button
E15 S6 OFF + S11 OFF S11 微動開關故障
S11 micro switch failure
OK 鍵
OK button
E16
撐褲腰撐開動作完畢 S2 ON
The tubular extending action is completed S2
ON
撐褲腰馬達故障
Tubular extending motor failure
OK 鍵
OK button
E17 S8 OFF 急停按下
Emergency stop press S8 ON
E18 S10 OFF 安全門打開
Security door open S10 ON
異常原因與對策 Mechanic or finished quality issue
報警說明 ALARM DESCRIPTION
P7
1. 接通電源
首先將機器總電源插頭插入插座，然後順時針旋
轉開關接通電源。OFF 表示關閉（如圖左）， ON
表示打開（如圖右）。
※1. 平時請儘量使用觸控板操作，
當觸控板不靈時方可使用手
動按鈕。
※2. 急停鍵僅在緊急情況下使用。
2. 手動按鈕
設備日常檢查
DAILY INSPECTION OF EQUIPMENT
1. Large limit adjustment
The maximum limit is the maximum position in
which the tiles extend. Press the M key to adjust
the maximum limit, the larger the value, the larger
the tile.
※1. Please use the touchpad to operate as much as possible
at ordinary times, and use the manual button only when the
touchpad is not working.
※2. The emergency stop button is only used in emergency situations.
2.Manual button
P8
計數器
Counter
指示燈
Indicator
擴張調節
Expansion adjustment
急停按鈕
Emergency button
電源開關
Power switch
3. 常見鋼絲損壞部位 3.Common damaged parts of steel wire
4. 鋼絲不同部位損壞的處理方案
鋼絲頭部損壞
常見現象：鋼絲頭部焊接處脫落、鋼絲頭
部折斷。
處理方案：按下啟動按鈕，輕踩左踏板將
大盤伸至最大限位，擰松內六角螺母，然
後從皮管處抽出損壞鋼絲。
橫槽處鋼絲損壞
常見現象：橫槽處鋼絲冒出卡住或折斷。
處理方案：在橫槽處選擇合適位置將鋼絲
剪斷，然後從兩端分別取出剪斷的鋼絲。
5. 更換鋼絲流程
(1) 取下廢鋼絲
按下啟動按鈕，輕踩左踏板將大盤伸至最
大限位，擰松內六角螺母，然後從皮管處
抽出損壞鋼絲。
(2) 換新鋼絲
①將鋼絲尾部伸入皮管，緩慢轉動鋼絲使
其進入橫槽，繼續伸入直至鋼絲穿出大
盤圓孔。
②將鋼絲伸出定位板，擰緊螺母初步定
位，輕踩右踏板使鋼絲緩慢縮回至最小
限位。
③根據鋼絲頭部伸出皮管長度手動調整直
至鋼絲頭部剛好在皮管入口處。
具體操作方法：擰松內六角螺母，用尖
嘴鉗夾住鋼絲尾部，緩慢移動直至位置
剛好合適。
6. 機械傳動部分
1. 每兩天向傳動部位滴入少量潤滑油。
2. 設備擴張機頭齒輪與齒條的定期加油為了
延長齒輪的使用壽命及使設備運行過程中
更平穩，我們需定期向齒輪齒條處加油潤
滑。
4. Solution for damage of different parts of steel wire.
Wire head damage
Commonplace: the welding part of the steel wire head falls off, and the
steel wire head breaks.
Solution: Press the start button, lightly step on the left pedal to extend
the big plate to maximum limit, loosen the inner hexagon nut, and then
pull out the damaged wire from the hose.
Damage to the steel wire at the transverse groove .
Commonplace: the steel wire is stuck or broken at the transverse
groove.
Solution: choose a suitable position at the transverse groove to cut the
steel wire, and take out the cut steel wires from both ends.
5. Process of replacing steel wire
(1) Remove the scrap steel wire
Press the start button, lightly step on the left pedal to extend the big
plate to the maximum limit. Loosen the inner hexagon nut, and pull out
the damaged steel wire from the hose.
(2) Renew the steel wire
①Extend the tail of the wire into the hose and slowly turn the wire to
enter transverse groove. Continue to extend the transverse groove
until the steel wire passes through the round hole of the big plate .
②Extend the steel wire out of the positioning plate, tighten the nut for
preliminary positioning, lightly step on right pedal slowly retracts the
wire to the minimum limit.
③According to the length of the wire head extending out of the hose,
manually adjust until the wire head is just at the entrance of the hose.
Specific operation method: loosen the hexagonal inner nut and
clamp it with needle-nose pliers .Hold the tail of the wire and move
slowly until the position is just right.
6. Mechanical transmission part
1. Drip a small amount of lubricating oil into the transmission part every
two days.
2. Regular refueling of the gear and rack of the equipment expansion head
in order to extend the gear .The service life of the equipment and make
the equipment more stable during operation, we need to set lubricate
the rack and pinion regularly.
P9
鋼絲頭部 Wire head 橫槽 Transverse groove
為確保機器的質量和安全，所有 SIRUBA 部件均通過了最高質量的檢驗和測試。 對於任何採用非正品
SIRUBA 部件進行更換和維修的情況，不僅可能導致保修範圍的損失，還可能導致對操作員和財產的意
外損壞。
在某些情況下，即使服務期尚未結束，諸如難以獲得零件等問題也可能使我們無法修理或更換故障物
品。 我們要求您就此事達成諒解
為了不斷為客戶提供高質量的機器和服務，我們不保證自生產停止 5年後停產的型號的零件供應服務。
服務部分政策
To ensure the quality and safety of machine, all SIRUBA parts pass the highest quality inspection and
test. For any case of adopting non-genuine SIRUBA parts for replacement and service, it may cause not
only losing the warranty coverage, but also the unexpected damage to the operator and property.
In some cases, issues such as difficulty of obtaining parts might make it impossible for us to repair
or replace malfunctioning items even if the service period has not yet ended. We ask for your
understanding on this matter
To continuously provide our customers the high quality machines and service, we do not guarantee the
parts supply service for the discontinued models after 5 years since the production stops.
SERVICE PARTS POLICY
P10
零件明細表
ASO-STM100 LZL 2021/9/1
1/1
P11
ASO-STM100 LZL 2021/9/1
1/1
P12
ASO-STM100 LZL 2021/9/1
1/1
P13
ASO-STM100 LZL 2021/9/1
1/1
P14
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/