Furuno MU150HD ユーザーマニュアル

i

IMPORTANT NOTICES

General

• This manual has been authored with simplified grammar, to meet the needs of international

users.

• The operator of this equipment must read and follow the descriptions in this manual. Wrong

operation or maintenance can cancel the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and equipment specifications can change without notice.

• The example screens (or illustrations) shown in this manual can be different from the screens

you see on your display. The screens you see depend on your system configuration and

equipment settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by FURUNO

will cancel the warranty.

• All brand and product names are trademarks, registered trademarks or service marks of their

respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal

in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the

correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery(ies), see the

chapter on Maintenance. Follow the instructions below if a battery(ies) is used.

In the European Union

The crossed-out trash can symbol indicates that all types of batteries

must not be discarded in standard trash, or at a trash site. Take the

used batteries to a battery collection site according to your national

legislation and the Batteries Directive 2006/66/EU.

In the USA

The Mobius loop symbol (three chasing arrows) indicates that Ni-Cd

and lead-acid rechargeable batteries must be recycled. Take the used

batteries to a battery collection site according to local laws.

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols can

increase when the other countries make their own recycle symbols in the future.

Cd

Ni-Cd Pb

ii

SAFETY INSTRUCTIONS

Indicates a condition that can cause death or serious

injury if not avoided.

Indicates a condition that can cause minor or moderate

injury if not avoided.

CAUTIONCAUTION

Read these safety instructions before you operate the equipment.

WARNING

CAUTION

Warning, Caution Prohibitive Action Mandatory Action

Safety Instructions for the Operator

WARNING

Immediately turn off the power at the

switchboard if water leaks into the

equipment or something is dropped

into the equipment.

Continued use of the equipment can cause

fire or electrical shock. Contact a FURUNO

agent for service.

Immediately turn off the power at the

switchboard if the equipment is emitting

smoke or fire.

Continued use of the equipment can cause

fire or electrical shock. Contact a FURUNO

agent for service.

Do not disassemble or modify the

equipment.

Fire, electrical shock or serious injury

can result.

Turn off the power immediately

if you feel the equipment is behaving

abnormally.

Turn off the power at the switchboard if

the equipment becomes abnormally warm

or is emitting odd noises. Contact a

FURUNO dealer or agent for advice.

Use the proper fuse.

Fuse rating is shown on the power

cable. Use of a wrong fuse can result

in damage to the equipment.

Do not place any object near the

exhaust or intake vent.

Fire may result.

Do not connect/disconnect the

signal cable while turning the power

on.

The unit may be damaged.

Handle the LCD monitor with care.

The face of the LCD monitor is made of

glass. Injury may result if the glass

breaks.

SAFETY INSTRUCTIONS

iii

Safety Instructions for the Installer

WARNINGWARNING

CAUTIONCAUTION

Turn off the power at the switchboard

before beginning the installation.

Fire or electrical shock can result if the

power is left on.

Do not install the equipment where it

may get wet from rain or water

splash.

Water in the equipment can result in fire,

electrical shock or damage to the

equipment.

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

Standard

compass

Steering

compass

MU-150HD

0.80 m

0.50 m

When lifting the display unit, hold it

together with the hard cover.

Grasping by the hard cover alone may

allow the display unit to fall, resulting in

possible bodily injury or damage to the

equipment.

The TFT LCD is constructed using the latest LCD techniques, and displays

99.99% of its pixels. The remaining 0.01% of the pixels may drop out or

blink, however this is not an indication of malfunction.

About the TFT LCD

iv

TABLE OF CONTENTS

Note: This manual contains both English and Japanese instructions. The Installation Materials,

Outline Drawings, and Interconnection Diagram are located at the back of this manual.

FOREWORD ....................................................................................................................v

SYSTEM CONFIGURATION ..........................................................................................vi

EQUIPMENT LISTS.......................................................................................................vii

1. MOUNTING, WIRING................................................................................................1

1.1 Preparation.................................................................................................................... 1

1.2 Flush Mounting, Fixed at Rear ...................................................................................... 3

1.3 Flush Mounting, Fixed at Front ..................................................................................... 6

1.4 Flush Mounting, Fixed at Rear, with hood..................................................................... 8

1.5 Desktop Mounting ....................................................................................................... 10

1.6 Flush Mounting a Series Side by Side ........................................................................ 13

1.7 Wiring .......................................................................................................................... 14

2. ADJUSTMENTS......................................................................................................16

2.1 RGB/DVI Setting ......................................................................................................... 16

2.2 Video Composite Signal Setting.................................................................................. 18

2.3 The Menu Window Setting.......................................................................................... 19

2.3.1 How to adjust the menu window.......................................................................... 19

2.3.2 How to change the signal name .......................................................................... 20

3. OPERATION ...........................................................................................................21

3.1 Controls....................................................................................................................... 21

3.2 How to Turn the Power On/Off.................................................................................... 22

3.2.1 Turn on/off the power........................................................................................... 22

3.2.2 Lock the operation ............................................................................................... 22

3.3 How to Adjust the Display Brilliance............................................................................ 22

3.4 How to Select the Source for Main Picture ................................................................. 23

3.5 How to Select the Source for the PIP Window............................................................ 23

3.6 SYSTEM Menu ........................................................................................................... 24

3.6.1 How to set the auto dimmer................................................................................. 24

3.6.2 How to adjust the brilliance from the external equipment .................................... 25

3.6.3 How to clear the memory..................................................................................... 25

4. MAINTENANCE, TROUBLESHOOTING................................................................26

4.1 Maintenance................................................................................................................ 26

4.2 Troubleshooting .......................................................................................................... 27

SPECIFICATIONS .....................................................................................................SP-1

INSTALLATION MATERIALS ..................................................................................... A-1

OUTLINE DRAWINGS................................................................................................. D-1

INTERCONNECTION DIAGRAM ................................................................................ S-1

v

FOREWORD

A Word to the Owner of the MU-150HD

FURUNO Electric Company thanks you for purchasing the MU-150HD 15” Marine Display. We are

confident you will discover why the FURUNO name has become synonymous with quality and re-

liability.

Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reli-

ability throughout the world. This dedication to excellence is furthered by our extensive global net-

work of agents and dealers.

Your equipment is designed and constructed to meet the rigorous demands of the marine envi-

ronment. However, no machine can perform its intended function unless properly installed and

maintained. Please carefully read and follow the operation, installation and maintenance proce-

dures set forth in this manual.

We would appreciate feedback from you, the end-user, about whether we are achieving our pur-

poses.

Thank you for considering and purchasing FURUNO.

Features

The main features of the MU-150HD are as shown below.

• Selectable screen from RGB (1 line), Digital (2 lines) or Composite (3 lines).

• Main or remote display for radars, video sounders, sonars, plotter. For the connectable equip-

ments, see "Connectable equipment" on page vi.

• High resolution display of 1024 x 768 (XGA)

• Brightness of 1000 cd/m

2

(maximum) and 0.3 cd/m

2

or less (minimum) for comfortable viewing

day and night.

• Brilliance adjustment automatically with the light sensor.

• Picture-in-picture function

• Power on/off automatically through the DVI signal.

Program Number

xx: minor change

CE declaration

With regards to CE declarations, please refer to our website (www.furuno.com), for further infor-

mation on RoHS conformity declarations.

Program Name Version Date of Modification

Main 1.xx Feb. 2010

vi

SYSTEM CONFIGURATION

Connectable equipment

Note 1: This equipment is used as a display for a Non-SOLAS radar or ECDIS.

Note 2: Landscape orientation only.

Note 3: When inputting SXGA, a circle may be displayed as an ellipse because the aspect ratio

differs. See "DISP MODE*" on page 17. Also, it may be difficult to read small characters.

Equipment Resolution Signal

FCV-1200L/M VGA Analog RGB, via IF-8000

CH-250/S VGA Analog RGB, via IF-8000

CH-270 VGA Analog RGB, via IF-8000

CH-300 VGA Analog RGB, via IF-8000

CSH-5L/8L XGA Analog RGB

FSV-24/S-BB SXGA Analog RGB

FSV-30/S-BB SXGA Analog RGB

FSV-84/L SXGA Analog RGB

FCV-30 SXGA Analog RGB

CI-68/88 VGA Analog RGB

FR-1510MK-3 XGA Analog RGB, OP03-153 required

FR-21x5 series SXGA Analog RGB, OP03-162 required

FAR-21x7 series SXGA DVI

FEA-2107 SXGA DVI

FEA-2807 SXGA DVI

FCR-21x7 series SXGA DVI

FCR-28x7 series SXGA DVI

MODEL1833C series (NavNet) VGA Analog RGB, OP03-176 required

MODEL1833C-BB series (NavNet) VGA Analog RGB

MODEL1824C series (NavNet vx2) VGA Analog RGB, OP03-176 required

MODEL1824C-BB series (NavNet vx2) VGA Analog RGB

MFD8 (NavNet 3D) VGA DVI

MFD12 (NavNet 3D) SVGA DVI

MFDBB (NavNet 3D)

SVGA

DVIXGA

SXGA

MODEL1824C/1833C/1943C,

FSV-30, FCV-30, FCV-1200L etc.

MFD8/MFD12/MFDBB,

FAR-21X7 series etc.

CCD camera,

DVD recorder, etc.

RGB

DVI

2 ports

VIDEO (NTSC/PAL)

3 ports

12-24 VDC

MARINE DISPLAY

MU-150HD

Environmental category

MU-150HD: Protected from the weather

vii

EQUIPMENT LISTS

Standard supply

*: See the Installation materials at the back of this manual.

Optional supply

Name Type Code No. Qty Remarks

Display Unit MU-150HD — 1 w/ Hard cover

Installation

Materials

CP26-01300 000-016-267 1 set • CP26-01302*

• Flush Mounting Plate Assy. (CP26-01301,

Code: 001-080-760) 2 pcs.

• Cable Assembly (MJ-A3SPF0017-050ZC,

Code: 000-157-995-10) 1 pc.

Accessories FP26-00401 001-175-940 1 set LCD Cleaning Cloth (19-028-3125-5, Code:

100-360-675-10) 1 pc.

Spare Parts SP26-00201 001-080-750 1 set • Fuse (FGBO-A 125V 5A PBF, Code: 000-

155-853-10) 3 pcs.

Name Type Code No. Qty Remarks

Cable Assembly

3COX-2P-6C 5M 001-077-230-10 1 Cable length: 5 m (15 pin D-sub

connector at both ends)

3COX-2P-6C 10M 001-077-220-10 1 Cable length: 10 m (15 pin D-

sub connector at both ends)

DVI-D/D S-LINK

5M

001-132-960-10 1 Cable length: 5 m

(with DVI-D connector at both

ends)

DVI-D/D S-LINK

10M

001-133-980-10 1 Cable length: 10 m

(with DVI-D connector at both

ends)

Bracket Assembly

(w/knobs)

OP26-2 000-016-268 1 set

Hood Assembly OP26-3 001-080-840 1 set

Flush Mount Kit

OP26-36 001-497-450

Either one of the two is supplied.

OP26-4 001-080-850

Glass Fixing Kit OP26-37 001-566-980 1 set For flush mouting (fixed at rear)/

desktop mounting

Glass Fixing Kit

(front)

OP26-38 001-566-990 1 set For flush mouting (fixed at front)

1

1. MOUNTING, WIRING

1.1 Preparation

Mounting type

You can install the display unit as follows. See the outline drawing at the back of this manual for

mounting dimensions.

• Flush mounting, fixed at rear (standard)

• Flush mounting, fixed at front (option)

• Flush mounting, fixed at rear, with hood (option)

• Desktop mounting (option)

• Flush mounting a series side by side, fixed at rear

Note: The face of the LCD monitor is made of glass. Handle it with care.

Mounting location

When you choose a mounting location, remember the following points:

• Make sure the mounting location is strong enough to support the weight of the unit.

• Locate the unit away from direct sunlight. An LCD may black out if it is exposed to direct sunlight

for a long time.

• Select a location where the display can be easily viewed and the controls can be easily operat-

ed.

• Leave enough space around the unit for service and maintenance. See the outline drawing at

the back of this manual for minimum service clearance.

• Locate the unit away from areas subject to water splash and rain.

• Observe the compass safe distances (see page iii) to prevent interference to a magnetic com-

pass.

Note: If the unit is installed with the screen tilted downwards, the appropriate glass fixing kit (see

“Optional supply” on page vii) must be used.

How to remove/attach the hard cover

Before you install this display unit, remove the hard cover as follows.

Grasping by the hard cover alone may

allow the display unit to fall, resulting in

possible bodily injury or damage to the

equipment.

When lifting the display unit, hold it

together with the hard cover.

CAUTION

1. MOUNTING, WIRING

2

How to remove the hard cover

To attach the hard cover, follow the illustration in the figure below.

How to attach the hard cover

Cable running

Before you install the display unit, run all cables you use. See the interconnection diagram at the

back of this manual.

Pull forward the upper

edge by pressing here

with thumbs.

The upper edge of the hard cover

Set the tabs on the top

of the hard cover to the

cutouts of the display

unit.

Push the tabs of the

bottom of the hard cover

strongly (2 places).

Hard cover

Tab

CutoutCutout

1. MOUNTING, WIRING

3

1.2 Flush Mounting, Fixed at Rear

This is the standard installation method.

1. Make a cutout in the mounting location with the “Flush mounting template” (included).

2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below.

3. Connect all cables at the back of the display unit. See section 1.7.

364±1 (14.33”)

314±1 (12.36”)

9 (0.35”)

4-ø18(0.71”)

Flush Mounting Sponge (H15)

for top and bottom

Flush Mounting Sponge (V15)

for right and left

1. MOUNTING, WIRING

4

4. Set the display unit to the cutout.

5. Screw the wing bolts and the wing nuts of the flush mount fixture so that the protector moves

to the mounting plate.

Cutout

Flush Mount Fixture 15

Wing Bolt

Mounting Plate

Protector

Set to the fixture.

Wing Nut

1. MOUNTING, WIRING

5

6. Fasten the flush mount fixture 15 to the right and left sides of the rear of the display unit with

the washer head screws (6 places).

7. Fasten the wing bolts, in the order of the number shown in the figure below so that the protec-

tors touch the mounting panel.

8. Fasten the wing bolts tightly, in the order shown in step 7.

9. Fasten the wing nuts tightly.

Washer Head Screw

Flush Mount Fixture 15

Wing Bolt

Wing Nut

Mounting Plate

Protector

Mounting Panel

1. MOUNTING, WIRING

6

1.3 Flush Mounting, Fixed at Front

If you do not have the enough space to fix the display unit from the rear, you can fix it from the

front with the optional flush mount kit OP26-36 (code no.: 001-497-450) or OP26-4 (code no.: 001-

080-850).

Flush Mount Kit

1. Make a cutout in the mounting location with the flush mounting template (included).

2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below.

Name Type Code No. Qty. Remarks

Flush Mounting Panel (15) OP26-36-1 001-497-520-00 Either

one of

the two

is sup-

plied.

For OP26-36

OP26-4-1 001-080-960-00 For OP26-4

Washer Head Screw M4x10 000-163-836-10 8

Self Tapping Screw 5x20 000-162-609-10 4

Flush Mounting Template C42-00909-x 000-172-636-1x 1 x denotes minor

modifications.

370 (14.57”)

4-ø18 (0.71”)

320 (12.60”)

9 (0.35”)

382±0.5 (15.04”)

332±0.5 (13.07”)

9 (0.35”)

Pilot hole

for mounting from the front

Flush Mounting Sponge (H15)

for top and bottom

Flush Mounting Sponge (V15)

for right and left

1. MOUNTING, WIRING

7

3. Attach the flush mounting panel (15) to the display unit from the rear with the washer head

screws (M4×10, 8 places, torque: 1.2 N•m). Do not confuse the top and bottom of the panel

and check that screw holes on the panel and unit match.

4. Connect all cables at the back of the display unit. See section 1.7.

5. Set the display unit assembly prepared at the step 3 to the cutout for the mounting location.

6. Fix the display unit to the cutout with the self tapping screws (4 places).

Flush

Mounting

Panel (15)

Washer

Head

Screw

Narrow

Wide

For OP26-36

For OP26-4

Wide

Narrow

Self Tapping Screw

1. MOUNTING, WIRING

8

1.4 Flush Mounting, Fixed at Rear, with hood

You can attach a hood when flush mounting the unit from the rear, using the hood assembly

OP26-3 (option).

Hood Assembly OP26-3 (Code: 001-080-840)

1. Make a cutout in the mounting location with the flush mounting template (included).

2. Fix the hood fixing plates to the right and left of the display unit with the flat head screws

(M3×8, 6 places, torque: 0.6 N•m).

Name Type Code No. Qty.

Hood (15) Assembly OP26-3-1 001-080-950-00 1

F-Mount Hood Gasket 15 26-005-2305 100-351-710-10 1

Hood Gasket Bottom 15 26-005-2306 100-351-720-10 1

F-Mount Hood Gasket Side 15 26-005-2307 100-351-730-10 2

Hood Fixing Plate 15 26-005-2302 100-351-321-10 2

Knob M4 03-163-2303 100-343-602-10 4

Flat Head Screw M3x8 000-172-167-10 6

Flush Mounting Template C42-00908 000-172-635-10 1

368±1 (14.49”)

314±1 (12.36”)

9 (0.35”)

4-ø18 (0.71”)

9 (0.35”)

Flat Head Screw

Hood Fixing Plate 15

1. MOUNTING, WIRING

9

3. Attach the “F-Mount Hood Gasket 15” to the top brim, the “Hood Gasket Bottom 15” to the

bottom brim, and then attach the “F-Mount Hood Gasket Side 15” to the right and left sides of

the display unit from the rear side as shown the figure below.

4. Follow steps 3 to 9 in section 1.2 to fix the display unit to the mounting location.

5. Loosely fix the knobs (4 pcs.) to the hood fixing plate.

6. Slide the cutouts of the hood assembly to the knobs.

F-Mount Hood Gasket 15

F-Mount Hood Gasket Side 15

Hood Gasket Bottom 15

Knob (4 pcs.)

Hood Fixing Plate 15

Cutout (4 places)

Hood (15) Assembly

1. MOUNTING, WIRING

10

7. Press the top of the hood to fit the knobs in the cutouts.

8. Fix the hood assembly with the knobs tightly (4 places).

1.5 Desktop Mounting

You can fix the display unit to a desktop, using the optional bracket assembly OP26-2.

Bracket assembly OP26-2 (Code: 000-016-268)

Name Type Code No. Qty.

Mounting Bracket (15) OP26-2-1 001-080-820-00

1

Bracket Support w/knobs OP26-2-2 001-080-830-00

Self-Tapping Screw 5x20 000-162-608-10 4

Binding Head Screw M4x10 000-172-165-10 9

Press

1. MOUNTING, WIRING

11

1. Loosen the knobs of the bracket support to separate the mounting bracket from the bracket

support.

2. Set the mounting bracket to the mounting location with four self tapping screws.

Mounting Bracket (15)

Bracket Support

Knob

Self-Tapping Screw

5x20

Mounting Bracket (15)

1. MOUNTING, WIRING

12

3. Attach the bracket support to the rear of the display unit with the binding head screws (9 plac-

es, torque: 1.2 N•m).

4. Connect all cables at the back of the display unit. See section 1.7.

5. Loosen the knobs of the bracket support and set them in the notches on the mounting bracket.

6. Adjust the angle of the display unit and fix the knobs tightly.

Binding Head Screw

Bracket Support

Mounting Bracket (15)

Knob

ページを読み込んでいます...

Furuno MU150HD ユーザーマニュアル

関連論文

その他の書類