www.furuno.com
MONITOR UNIT
OPERATOR'S MANUAL
Model
表示部
取扱説明書
MU-231
・
本書の無断複写複製(コピー)は特定の
場合を除き、当社権利侵害になります。
(ETMI) MU-231
Pub. No. OMC-44690-D5
Printed in Japan
・ 機器の修理・使用方法等に関するお問い合わせは、お買い上げの販売店・代理店、最寄りの
当社支店・営業所あてへお願いします。
(Elemental Chlorine Free)
The paper used in this manual
is
elemental chlorine free.
FURUNO Authorized Distributor/Dealer お問い合わせは
: MAY 2011
: APR. 22, 2020
A
D5
00017449213
i
IMPORTANT NOTICES
General
• This manual has been authored with simplified grammar, to meet the needs of international users.
• The operator of this equipment must read and follow the instructions in this manual.
Wrong operation or maintenance can void the warranty or cause injury.
• Do not copy any part of this manual without written permission from FURUNO.
• If this manual is lost or worn, contact your dealer about replacement.
• The contents of this manual and the equipment specifications can change without notice.
• The example screens (or illustrations) shown in this manual can be different from the screens you
see on your display. The screens you see depend on your system configuration and equipment
settings.
• Save this manual for future reference.
• Any modification of the equipment (including software) by persons not authorized by FURUNO will
void the warranty.
• The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.
- Name: FURUNO EUROPE B.V.
- Address: Ridderhaven 19B, 2984 BT Ridderkerk, The Netherlands
• All brand, product names, trademarks, registered trademarks, and service marks belong to their
respective holders.
How to discard this product
Discard this product according to local regulations for the disposal of industrial waste. For disposal in
the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the
correct method of disposal.
How to discard a used battery
Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter
on Maintenance. If a battery is used, tape the + and - terminals of the battery before disposal to pre-
vent fire, heat generation caused by short circuit.
In the European Union
The crossed-out trash can symbol indicates that all types of batteries
must not be discarded in standard trash, or at a trash site. Take the
used batteries to a battery collection site according to your national
legislation and the Batteries Directive 2006/66/EU.
In the USA
The Mobius loop symbol (three chasing arrows) indicates that
Ni-Cd and lead-acid rechargeable batteries must be recycled.
Take the used batteries to a battery collection site according to
local laws.
In the other countries
There are no international standards for the battery recycle symbol. The number of symbols can in-
crease when the other countries make their own recycle symbols in the future.
Cd
Ni-Cd Pb
ii
SAFETY INSTRUCTIONS
Indicates a condition that can cause death or serious
injury if not avoided.
Indicates a condition that can cause minor or moderate
injury if not avoided.
Use the proper fuse.
Use of a wrong fuse can cause fire or
damage to the equipment.
Handle the LCD monitor with care.
The face of the LCD monitor is made
of glass.
Injury may result if the
glass breaks.
Read these safety instructions before you operate the equipment.
WARNING
CAUTION
Warning, Caution
Prohibitive Action
Mandatory Action
Safety Instructions for the Operator
WARNINGWARNING
WARNINGWARNING
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury
can result.
Do not place any object near the
exhaust or intake vent.
Fire may result.
CAUTIONCAUTION
Do not connect/disconnect the signal
cable while turning the power on.
The unit may be damaged.
Immediately turn off the power at the
switchboard if water leaks into the
equipment or something is dropped
into the equipment.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Immediately turn off the power at the
switchboard if the equipment is
emitting smoke or fire.
Continued use of the equipment can
cause fire or electrical shock. Contact a
FURUNO agent for service.
Turn off the power immediately if you
feel the equipment is behaving
abnormally.
Turn off the power at the switchboard if
the equipment becomes abnormally
warm or is emitting odd noises. Contact
a FURUNO dealer or agent for advice.
SAFETY INSTRUCTIONS
iii
Safety Instructions for the Installer
WARNINGWARNING
CAUTIONCAUTION
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage to the
equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
MU-231
Standard
compass
Steering
compass
0.85 m 0.55 m
WARNING
㆙࿌
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
ឤ㟁䛾ᜍ䜜䛒䜚䚹
䝃䞊䝡䝇䝬䞁௨እ䛾᪉䛿䜹䝞䞊䜢㛤䛡
䛺䛔䛷ୗ䛥䛔䚹ෆ㒊䛻䛿㧗㟁ᅽ㒊ศ䛜
ᩘከ䛟䛒䜚䚸୍䛥䜟䜛䛸༴㝤䛷䛩䚹
Warning Labels
Warning labels are attached to the equipment. Do not remove the labels. If a label is missing or damaged, contact a
FURUNO agent or dealer about replacement.
Name: Warning Label 1
Type: 86-003-1011-3
Code No.: 100-236-233-10
Name: High Voltage Warning Label
Type: 16-018-3206-0
Code No.: 100-297-770-10
The TFT LCD is constructed using the latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01% of the pixels may drop out or
blink, however this is not an indication of malfunction.
About the TFT LCD
About the TFT LCD
About the TFT LCD
iv
TABLE OF CONTENTS
Note: This manual contains both English and Japanese instructions. The Packing Lists,
Outline Drawings, and Interconnection Diagram are located at the back of this manual.
FOREWORD ....................................................................................................................v
SYSTEM CONFIGURATION ..........................................................................................vi
EQUIPMENT LISTS.......................................................................................................vii
1. MOUNTING, WIRING................................................................................................1
1.1 Preparation.................................................................................................................... 1
1.2 Flush Mount, Fixed at Front .......................................................................................... 2
1.3 Flush Mount, Fixed at Front, with Hood ........................................................................ 4
1.4 Flush Mount, Fixed at Rear........................................................................................... 5
1.5 Flush Mount, Fixed at Rear, with Hood......................................................................... 6
1.6 Tabletop Mount ............................................................................................................. 8
1.7 Flush Mount a Series Side by Side ............................................................................. 10
1.8 Wiring .......................................................................................................................... 11
2. ADJUSTMENTS......................................................................................................12
2.1 Installation Settings ..................................................................................................... 12
2.2 RGB/DVI Setting (For Non-SOLAS)............................................................................ 14
2.3 Video Composite Signal Setting (For Non-SOLAS) .................................................... 16
2.4 The Menu Window Setting (For Non-SOLAS) ............................................................ 17
2.4.1 How to adjust the menu window.......................................................................... 17
2.4.2 How to change the signal name .......................................................................... 18
3. OPERATION ...........................................................................................................19
3.1 Controls....................................................................................................................... 19
3.2 How to Turn the Power On/Off.................................................................................... 19
3.2.1 Turn the power on/off........................................................................................... 19
3.2.2 Unlock the key operation ..................................................................................... 20
3.3 How to Adjust the Display Brilliance............................................................................ 20
3.4 How to Select the Source for Main Picture ................................................................. 21
3.5 How to Display the PIP Window.................................................................................. 21
3.6 SYSTEM Menu ........................................................................................................... 21
3.6.1 How to set the auto dimmer................................................................................. 21
3.6.2 How to clear the memory..................................................................................... 22
4. MAINTENANCE, TROUBLESHOOTING................................................................23
4.1 Maintenance................................................................................................................ 23
4.2 Troubleshooting .......................................................................................................... 24
4.3 Parts Location and Parts List ...................................................................................... 24
SPECIFICATIONS .....................................................................................................SP-1
PACKING LISTS.......................................................................................................... A-1
OUTLINE DRAWINGS.................................................................................................D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1
v
FOREWORD
A Word to the Owner of the MU-231
FURUNO Electric Company thanks you for purchasing the MU-231 23.1” Monitor Unit. We are
confident you will discover why the FURUNO name has become synonymous with quality and re-
liability.
Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reli-
ability throughout the world. This dedication to excellence is furthered by our extensive global net-
work of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine envi-
ronment. However, no machine can perform its intended function unless properly installed and
maintained. Please carefully read and follow the operation, installation and maintenance proce-
dures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our goal.
Thank you for considering and purchasing FURUNO.
Features
Program
xx: minor change
You can see these program numbers on the [SYSTEM] menu (see section 3.6). To open the
[SYSTEM] menu, unlock the key operation (see paragraph 3.2.2).
Note: When you connect the monitor unit to FMD-3300*, FAR-28x7 series, FEA-2807, FCR-28x7
series, FCR-28x9 series or FAR-33x0 series lock the key operation (see paragraph 3.2.2) after
confirming the program numbers.
*: To connect the monitor unit to the FMD-3300, the program version for the APR PROGRAM must
be 2651020-01.02 or higher.
CE Declarations
With regards to CE declarations, please refer to our website (www.furuno.com), for further infor-
mation on RoHS conformity declarations.
The main features of the MU-231 are as shown below.
• Selectable screen from RGB (1 port), Digital (2 ports) or Composite (1 port).
• Main or remote display for radars, video sounders, sonars, plotter. For the connectable equip-
ment, see the SYSTEM CONFIGURATION on page vi.
• High resolution display of 1600 x 1200 (UXGA)
• Automatic brilliance adjustment by the light sensor.
• Picture-in-picture function
• Power on/off automatically through the DVI signal.
Program Name Version Date of Change
APR PROGRAM 2651020-01.xx May. 2011
FPGA PROGRAM 2651021-01.xx May. 2011
vi
SYSTEM CONFIGURATION
Example: Connectable equipment
Note 1: Landscape orientation only.
Note 2: *: When inputting SXGA, a circle may be displayed as an ellipse because the aspect ratio
differs (see "DISP MODE*" on page 15).
Equipment Resolution Signal
FCV-1200L/1200LM VGA Analog RGB, via IF-8000
FSV-24/24S SXGA* Analog RGB
FSV-30/30S SXGA* Analog RGB
FSV-84/84L SXGA* Analog RGB
FSV-85/85L SXGA* Analog RGB
FCV-30 SXGA* Analog RGB
FAR-28x7 SXGA DVI
FEA-2807 SXGA DVI
FCR-28x7 SXGA DVI
FMD-3300 UXGA DVI
FCR-28x9 UXGA DVI
FAR-33x0 UXGA DVI
MFDBB (NAVnet 3D)
SVGA
DVIXGA
SXGA*
100-230 VAC
MONITOR UNIT
MU-231
Environmental category
MU-231: Protected from the weather
RGB
DVI (2 ports)
VIDEO (NTSC/PAL)
RS-232C
FSV-30/30S, etc.
FAR-28x7, FEA-2807,
FCR-28x7, FAR-33x0, etc.
CCD camera, DVD recorder, etc.
FEA-2807, FCR-28x7, etc.
RS-485
FMD-3300, FCR-28x9, FAR-33x0, etc.
vii
EQUIPMENT LISTS
Standard supply
Optional supply
Name Type Code No. Qty Remarks
Monitor Unit MU-231 - 1
Installation
Materials
CP26-01900 000-019-211 1 set • Installation Materials (CP26-01901, Code
No.: 001-116-670, See page A-3.)
• Cable Assembly (DVI-D/D S-LINK 5M,
Code No.: 001-132-960-10)
Accessories FP26-00401 001-387-540 1 set LCD Cleaning Cloth (19-028-3125-6,
Code No.: 100-360-676-10)
Spare Parts SP26-00801 001-468-150 1 set Glass Tube Fuse (FGBO-A 250V 5A PBF,
Code No.: 000-155-840-10) 3 pcs.
Name Type Code No. Remarks
Cable Assembly 3COX-2P-6C
5M
001-077-230-10 Cable length: 5 m (15 pin D-sub connector at
both ends)
3COX-2P-6C
10M
001-077-220-10 Cable length: 10 m (15 pin
D-sub connector at both ends)
DVI-D/D
S-LINK 5M
001-132-960-10 Cable length: 5 m (with DVI-D connector at
both ends)
DVI-D/D
S-LINK 10M*
1
001-133-980-10 Cable length: 10 m (with DVI-D connector at
both ends)
Bracket Assembly OP26-15 001-116-730
Hood Assembly OP26-16 001-116-740-01
Dust Cover for
23” LCD
26-007-2141 001-121-240-10
Flush Mount Kit OP26-17 001-116-750 • Flush Mounting Sponge H (26-007-2045,
Code No.: 100-361-270-10)
• Packing (26-007-2172, Code No.: 100-
361-380-10)
• Washer Head Screw B (M4x10, Code
No.: 000-163-836-10)
• Flush Mount Fixture 23 (OP26-17-1, Code
No.: 001-116-770)
• Flush Mount Fixture 23*
2
(OP26-17-2,
Code No.: 001-120-370)
• Connection Clamp L*
3
(OP26-18-1, Code
No.: 001-116-780)
• Connection Clamp S1*
3
(OP26-18-2,
Code No.: 001-116-790)
• Connection Clamp S2*
3
(OP26-18-3,
Code No.: 001-119-290)
Note: The quantity of each part depends on
the number of units connected.
OP26-18
(Two units
installed side
by side)
000-017-273
OP26-19
(Three units
installed side
by side)
000-017-274
Hood (23) As-
sembly
OP26-25 001-139-380-01
EQUIPMENT LISTS
viii
*1: This is not available for UXGA signal. *2: For OP26-17. *3: For OP26-18/OP26-19.
Monitor Replace-
ment Kit
OP26-27 001-139-570
Name Type Code No. Remarks
1
1. MOUNTING, WIRING
1.1 Preparation
Mounting method
You can install the monitor unit as follows. See the outline drawings at the back of this manual for
mounting dimensions.
• Flush mount, fixed at front (standard)
• Flush mount, fixed at front, with hood (option)
• Flush mount, fixed at rear (option)
• Flush mount, fixed at rear, with hood (option)
• Tabletop mount (option, hood-mountable)
• Flush mount a series side by side, fixed at rear
Note 1: The face of the LCD is made of glass. Handle it with care.
Note 2: For flush mount, take care so that the monitor unit does not fall during the installation.
Mounting location
Select a mounting location considering the following points. This equipment is free from electro-
magnetic fields.
• Make sure the mounting location is strong enough to support the weight of the unit.
• Locate the unit away from direct sunlight. An LCD may darken if it is exposed to direct sunlight
for a long time.
• Select a location where the screen can be easily viewed and the controls can be easily operat-
ed.
• Leave enough space around the unit for service and maintenance. See the outline drawings at
the back of this manual for minimum service clearance.
• Locate the unit away from areas subject to water splash and rain.
• Observe the compass safe distances (see page iii) to prevent interference to a magnetic com-
pass.
Run cables before installing the monitor unit
Run all cables before you install the monitor unit. See the interconnection diagram at the back of
this manual.
1. MOUNTING, WIRING
2
1.2 Flush Mount, Fixed at Front
Flush mount, fix at front is the standard installation method.
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Attach the flush mounting sponges
to the back of the monitor unit in
the order shown in the figure at
right.
3. Attach the flush mounting panels to the monitor unit from the rear with the binding head
screws (M4x10, 8 pcs., supplied).
Note 1: The shape of the flush mounting panel is different between right and left. The left pan-
el is marked "A"; the right panel is marked "B".
Note 2: To tighten screws, first tighten the top and bottom screws then tighten the middle two
screws.
Note 3: Attach the flush mounting panels to both sides of the monitor unit with no gap.
4. Connect all cables at the back of the monitor unit. See section 1.8.
5. Set the monitor unit assembly to the cutout.
6. Fix the monitor unit to the cutout with the self-tapping screws (6x30, 4 pcs., supplied).
Flush Mounting
Sponge H (2 mm)
for left and right
Flush Mounting
Sponge (5 mm) for
top and bottom
B
A
Rear view
A
B
Binding Head Screw (8 places)
Flush Mounting Panel A
Flush Mounting Panel B
Self-Tapping Screw
(4 places)
1. MOUNTING, WIRING
3
7. Set the masking panel S to each side of the monitor unit.
How to attach or detach the masking panel S
Do the following to attach or detach the masking panel S.
Masking Panel S
Reverse view of masking panel S
Tab A
Tab B
Front side of
monitor unit
Set the masking panel S to each side of the
monitor unit. Attach each tab A to the monitor
unit. Be careful not to break the tabs.
Set tab B to
the edge of
the monitor
unit.
Monitor unit
To attach, follow order of right arrow (→). To detach, follow order of left arrow (←).
Masking
panel S
Detach: Push the masking panel S in the
direction 1, then release each tab A one
by one
(three places of a, b and c)
in the
direction 2.
→→
←
←
1
2
Attach: Push the
masking panel S in
the direction ,
rotate the panel
toward the monitor
unit, then set each
tab A one by one
(three places of a, b
and c) .
a
b
c
1
2
1. MOUNTING, WIRING
4
1.3 Flush Mount, Fixed at Front, with Hood
The flush mount, fixed at front method allows you to attach a hood (23) assembly OP26-25 (op-
tion) to the monitor unit.
Hood (23) assembly OP26-25 (Code No.: 001-139-380-01)
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Follow steps 2 to 6 in section 1.2.
3. Loosely fix the knobs M4 (4 pcs.) to the hood fixing plates
(front) from inside the plates.
4. Remove the binding head screws (M3x5,
6pcs.) from the flush mounting panels A
and B attached to the monitor unit.
5. Attach the hood fixing plates (front) to the right and left
sides of the monitor unit with the binding head screws
(M3x8, 6pcs.).
6. Press and rub folds on the hood with your hands to make
creases clearly. The degree of creases should be within 90°
when the hood is opened.
Name Type Code No. Qty
Hood (23) Assembly OP26-16-1 001-116-760 1
Knob M4 03-163-2303 100-343-602-10 4
Hood Fixing Plate (Front) 26-007-2157 100-366-431-10 2
Binding Head Screw M3x8 000-172-166-10 6
Knob M4
Hood Fixing
Plate (Front)
Flush
Mounting
Panel B
Flush
Mounting
Panel A
Binding Head
Screw (6 pcs.)
Hood Fixing
Plate (Front)
Binding
Head Screw
(6 pcs.)
Correct
Improper,
insufficient
1. MOUNTING, WIRING
5
7. Set the cutouts of the hood (23) assembly to
the knobs on the hood fixing plates (front).
8. Press the top of the hood (23) assembly to set the knobs in the cut-
outs.
9. Set the hood (23) assembly with the knobs tightly (4 pcs.).
1.4 Flush Mount, Fixed at Rear
The flush mount, fixed at rear method requires the flush mount kit OP26-17 (option, see page vii).
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Attach the flush mounting sponges H
and packings to the back of the
monitor unit in the order shown in the
figure at right.
3. Screw the wing bolts and the wing nuts of the flush mount fixture so that the protector for
screw moves to the fixing plate.
4. Connect all cables at the back of the monitor unit. See section 1.8.
5. Set the monitor unit to the cutout.
Hood (23)
Assembly
Cutout (4 places)
Hood
Fixing
Plate
(Front)
Knob M4 (4 pcs.)
Press
Press
Packing for top
and bottom
Flush Mounting
Sponge H for left
and right
Flush Mount Fixture 23
Wing Bolt
Protector for
Screw
Move to the fixing plate.
Wing Nut
Fixing Plate
1. MOUNTING, WIRING
6
6. Fasten the flush mount fixture 23 to the left, right, top and bottom of the rear of the monitor
unit with the washer head screws (16 pcs.).
7. Fasten each wing bolt so that the protector for screw touches the mounting panel.
8. Fasten the wing bolts tightly to secure the monitor unit.
9. Fasten the wing nuts tightly.
1.5 Flush Mount, Fixed at Rear, with Hood
The flush mount, fixed at rear method allows you to attach a hood assembly OP26-16 (option) to
the monitor unit.
Hood assembly OP26-16 (Code No.: 001-116-740-01)
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Fix the hood fixing plates to the right and
left sides of the monitor unit with the flat
head screws (6 pcs.).
Name Type Code No. Qty
Hood (23) Assembly OP26-16-1 001-116-760 1
Flat Head Screw M3x8 000-172-167-10 6
Knob M4 03-163-2303 100-343-602-10 4
Flush Mounting Sponge 26-007-2046 100-361-280-10 2
Hood Fixing Plate 26-007-2152 100-361-320-10 2
Hood Packing A 26-007-2154 100-361-340-10 2
Hood Packing B 26-007-2155 100-361-350-10 2
Packing 26-007-2156 100-361-360-10 2
Washer Head Screw B
(16 places)
Flush Mount Fixture 23
Rear view
Note: The flush mount fixtures (4 pcs.) are identical.
The fixing holes are different between “top and
bottom” and “right and left” as shown below.
Mounting Panel
Fixing Plate
Wing Bolt
Wing Nut
Protector for Screw
Flat
Head
Screw
Hood Fixing Plate
1. MOUNTING, WIRING
7
3. Attach the flush mounting sponges to the top and bottom brims. Then, attach the hood packing
A, the packing and the hood packing B to the right and left brims of the monitor unit from the
rear side.
4. Follow steps 3 to 9 in section 1.3 to fix the monitor unit to the mounting location.
5. Loosely fix the knobs (4 pcs.) to the hood fixing plate from inside the plate.
6. Press and rub folds on the hood with your hands to make creases clearly (see step 6 in
section 1.3).
7. Set the cutouts of the hood (23) assembly to
the knobs on the hood fixing plates.
8. Press the top of the hood assembly to set the knobs in the cutouts.
9. Set the hood assembly with the knobs tightly (4 pcs.).
Flush Mounting
Sponge
Flush Mounting
Sponge
Hood
Packing A*
Hood
Packing B*
Packing
*: The length of hood packing A is longer
than that of hood packing B.
Hood
Fixing
Plate
Hood (23)
Assembly
Knob (4 pcs.)
Cutout (4 places)
Press
Press
1. MOUNTING, WIRING
8
1.6 Tabletop Mount
You can fix the monitor unit to a tabletop, using the bracket assembly OP26-15 (option).
Bracket Assembly OP26-15 (Code No.: 001-116-730)
1. Assemble two brackets (L and R) and spacer (23) with flat washers, spring washers, hexag-
onal head slot bolts (M10x30). Cover each hexagonal head slot bolt with hole plug. Also, cover
each screw hole on the hanger with a snap button (4 pcs.).
2. Fix the above assembly to the mounting location with four hex bolts (M10, 4 pcs, local supply).
3. Attach the flush mounting panels to the monitor unit from the rear with the binding head
screws (M4x10, 8 pcs., supplied). See step 3 in section 1.2.
4. Connect all cables at the back of the monitor unit. See section 1.8.
Name Type Code No. Qty
Bracket L 03-163-7712 100-366-311-10 1
Bracket R 03-163-7713 100-366-321-10 1
Spacer (23) 03-163-2071 100-305-371-10 1
Hole Plug CP-30-HP-13 000-160-074-10 2
Snap Button KB-13 Black 000-570-276-10 4
Hex. Head Slot Bolt-B Washer M6x25 000-162-949-10 4
Hexagonal Head Slot Bolt M10x30 000-162-884-10 2
Hexagonal Head Bolt M4x10 000-162-728-10 2
Spring Washer M10 000-167-233-10 2
Flat Washer M10 000-167-232-10 2
Binding Head Screw M4x10 000-172-165-10 8
Spacer Assembly OP26-21-1 001-143-370 4
Flat Washer
Spring Washer
Hexagonal Head Slot Bolt
Hole Plug
Spacer (23)
Bracket L
Bracket R
Snap Button
Snap Button
Hex Bolt (4 places)
(Type A: M12, Type B: M10)
1. MOUNTING, WIRING
9
5. Remove the paper from the double-sided tape on
the spacer assembly and then attach the spacer as-
sembly to the bracket.
6. Fasten the monitor unit to the bracket assembly with four hex. head slot bolt-B washers
(M6x25).
7. Set the masking panel S to each side of the monitor unit. See "How to attach or detach the
masking panel S" in section 1.2.
How to attach the hood
You can attach a hood to the tabletop-mounted monitor unit.
Use the hood (23) assembly OP26-25 (option).
1. Follow steps 1 to 6 in section 1.6.
2. Follow steps 3 to 9 in section 1.3.
A
ttach the
spacer
assemblies to
these places.
Hex. Head
Slot Bolt-B
Washer
1. MOUNTING, WIRING
10
1.7 Flush Mount a Series Side by Side
You can flush mount two or three monitor units side by side, using the optional flush mount kit
OP26-18 for two monitor units or OP26-19 for three monitor units (see page vii).
1. Make a cutout in the mounting location as shown below (see page D-4).
2. Follow steps 2 to 6 in section 1.4 to set the two or three monitor units in the mounting location.
Use only two flush mount fixtures 23 for the left and right of the rear of the monitor unit.
3. Attach the connection clamps L and S1/S2 with the washer head screws B to join the two or
three monitor units.
4. Fasten two or three monitor units tightly. See steps 7 to 9 in section 1.4.
1098
±
1
471
±1
(10)
(10)
4-
φ
20
1651
±1
471
±1
(10)
(10)
4-
φ
20
For two monitor units
For three monitor units
Flush Mount Fixture 23
Flush Mount Fixture 23
Two monitor units side by side
(Rear)
Three monitor units side by side
(Rear)
Connection Clamp
L (4 places)
Connection
Clamp S1
Connection Clamp
S1 (2 places)
Connection
Clamp L (2
places)
Connection
Clamp S2
Connection
Clamp S1
Connection
Clamp S2
Connection Clamp
S2 (2 places)
Two monitor units side by side
Three monitor units side by side
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
