Furuno MU190HD ユーザーマニュアル

カテゴリー
テレビ
タイプ
ユーザーマニュアル
Pub. No. OMC-44570-D1
( ETMI) MU-190HD
A
: FEB. 2010
D1
: OCT. 19, 2020
00017222013
i
IMPORTANT NOTICES
General
This manual has been authored with simplified grammar, to meet the needs of international users.
The operator of this equipment must read and follow the instructions in this manual. Wrong oper-
ation or maintenance can void the warranty or cause injury.
Do not copy any part of this manual without written permission from FURUNO.
If this manual is lost or worn, contact your dealer about replacement.
The contents of this manual and the equipment specifications can change without notice.
The example screens (or illustrations) shown in this manual can be different from the screens you
see on your display. The screens you see depend on your system configuration and equipment
settings.
Save this manual for future reference.
Any modification of the equipment (including software) by persons not authorized by FURUNO will
void the warranty.
The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.
- Name: FURUNO EUROPE B.V.
- Address: Ridderhaven 19B, 2984 BT Ridderkerk, The Netherlands
All brand, product names, trademarks, registered trademarks, and service marks belong to their
respective holders.
How to discard this product
Discard this product according to local regulations for the disposal of industrial waste. For disposal
in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the
correct method of disposal.
How to discard a used battery
Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter
on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of bat-
tery before disposal to prevent fire, heat generation caused by short circuit.
In the European Union
The crossed-out trash can symbol indicates that all types of batter-
ies must not be discarded in standard trash, or at a trash site. Take
the used batteries to a battery collection site according to your na-
tional legislation and the Batteries Directive 2006/66/EU.
In the USA
The Mobius loop symbol (three chasing arrows) indicates that Ni-
Cd and lead-acid rechargeable batteries must be recycled. Take
the used batteries to a battery collection site according to local
laws.
In the other countries
There are no international standards for the battery recycle symbol. The number of symbols can in-
crease when the other countries make their own recycle symbols in the future.
Cd
Ni-Cd Pb
ii
SAFETY INSTRUCTIONS
WARNING
Indicates a condition that can cause death or serious
injury if not avoided.
CAUTION
Indicates a condition that can cause minor or moderate
injury if not avoided.
Warning, Caution
Mandatory Action
Prohibitive Action
Read these safety instructions before you operate the equipment.
WARNING
WARNING
CAUTION
CAUTION
Do not disassemble or modify the
equipment.
Do not place any object near the
exhaust or intake vent.
Fire may result.
Do not connect/disconnect the signal
cable while turning the power on.
The unit may be damaged.
Safety Instructions for the Operator
Fire, electrical shock or serious injury
can result.
Use the proper fuse.
Fuse rating is shown on the power
cable. Use of a wrong fuse can result in
damage to the equipment.
Handle the LCD monitor with care.
The face of the LCD monitor is made
of glass.
Injury may result if the
glass breaks.
Immediately turn off the power at the
switchboard if water leaks into the
equipment or something is dropped
into the equipment.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Turn off the power immediately
if you feel the equipment is behaving
abnormally.
Turn off the power at the switchboard if
the equipment becomes abnormally warm
or is emitting odd noises. Contact a
FURUNO dealer or agent for advice.
WARNING
WARNING
SAFETY INSTRUCTIONS
iii
WARNING
WARNING
CAUTION
CAUTION
MU-190HD
Standard Steering
compass compass
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage to the
equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
When lifting the display unit, hold it
together with the hard cover.
Grasping by the hard cover alone may
allow the display unit to fall, resulting in
possible bodily injury or damage to the
equipment.
1.05 m 0.65 m
Safety Instructions for the Installer
About the TFT LCD
The TFT LCD is constructed using the latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01% of the pixels may drop out or
blink, however this is not an indication of malfunction.
iv
TABLE OF CONTENTS
Note: This manual contains both English and Japanese instructions. The Installation
Materials, Outline Drawings, and Interconnection Diagram are located at the back of this
manual.
FOREWORD ..................................................................................................................v
SYSTEM CONFIGURATION.........................................................................................vi
EQUIPMENT LISTS .....................................................................................................vii
1. MOUNTING, WIRING ..............................................................................................1
1.1 Preparation..................................................................................................................1
1.2 Flush Mounting, Fixed at Rear .................................................................................... 3
1.3 Flush Mounting, Fixed at Front ................................................................................... 6
1.4 Flush Mounting, Fixed at Rear, with hood................................................................... 8
1.5 Desktop Mounting ..................................................................................................... 10
1.6 Flush Mounting a Series Side by Side ...................................................................... 13
1.7 Wiring ........................................................................................................................ 14
2. ADJUSTMENTS ....................................................................................................16
2.1 RGB/DVI Setting ....................................................................................................... 16
2.2 Video Composite Signal Setting................................................................................ 18
2.3 The Menu Window Setting ........................................................................................ 19
2.3.1 How to adjust the menu window ........................................................................ 19
2.3.2 How to change the signal name ........................................................................ 20
3. OPERATION..........................................................................................................21
3.1 Controls.....................................................................................................................21
3.2 How to Turn the Power On/Off.................................................................................. 22
3.2.1 Turn on/off the power......................................................................................... 22
3.2.2 Lock the operation ............................................................................................. 22
3.3 How to Adjust the Display Brilliance.......................................................................... 22
3.4 How to Select the Source for Main Picture ............................................................... 23
3.5 How to Select the Source for the PIP Window.......................................................... 23
3.6 SYSTEM Menu ......................................................................................................... 24
3.6.1 How to set the auto dimmer............................................................................... 24
3.6.2 How to adjust the brilliance from the external equipment .................................. 25
3.6.3 How to clear the memory................................................................................... 25
4. MAINTENANCE, TROUBLESHOOTING..............................................................26
4.1 Maintenance.............................................................................................................. 26
4.2 Troubleshooting ........................................................................................................ 27
SPECIFICATIONS....................................................................................................SP-1
INSTALLATION MATERIALS ................................................................................... A-1
OUTLINE DRAWINGS ...............................................................................................D-1
INTERCONNECTION DIAGRAM............................................................................... S-1
v
FOREWORD
A Word to the Owner of the MU-190HD
FURUNO Electric Company thanks you for purchasing the MU-190HD 19” Marine Display. We are
confident you will discover why the FURUNO name has become synonymous with quality and re-
liability.
Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reli-
ability throughout the world. This dedication to excellence is furthered by our extensive global net-
work of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine envi-
ronment. However, no machine can perform its intended function unless properly installed and
maintained. Please carefully read and follow the operation, installation and maintenance proce-
dures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our pur-
poses.
Thank you for considering and purchasing FURUNO.
Features
The main features of the MU-190HD are as shown below.
Selectable screen from RGB (1 line), Digital (2 lines) or Composite (3 lines).
Main or remote display for radars, video sounders, sonars, plotter. For the connectable equip-
ments, see "Connectable equipment" on page vi.
High resolution display of 1280 x 1024 (SXGA)
Brightness of 1000 cd/m
2
(maximum) and 0.3 cd/m
2
or less (minimum) for comfortable viewing
day and night
Brill adjustment automatically with the light sensor.
• Picture-in-picture function
Power on/off automatically through the DVI signal.
Program
xx: minor change
CE declaration
With regards to CE declarations, please refer to our website (www.furuno.com), for further infor-
mation on RoHS conformity declarations.
Program Name Version Date of Modification
Main 1.xx Feb. 2010
vi
SYSTEM CONFIGURATION
Connectable equipment
Note 1: This equipment is used as a display for a Non-SOLAS radar or ECDIS.
Note 2: Landscape orientation only.
Note 3: When inputting VGA, SVGA or XGA, a circle may be displayed as an ellipse because the
aspect ratio differs. (see "DISP MODE*" on page 17.)
Equipment Resolution Signal
FCV-1200L/M VGA Analog RGB, via IF-8000
CH-250/S VGA Analog RGB, via IF-8000
CH-270 VGA Analog RGB, via IF-8000
CH-300 VGA Analog RGB, via IF-8000
CSH-5L/8L XGA Analog RGB
FSV-24/S-BB SXGA Analog RGB
FSV-30/S-BB SXGA Analog RGB
FSV-84/L SXGA Analog RGB
FCV-30 SXGA Analog RGB
CI-68/88 VGA Analog RGB
FR-1510MK-3 XGA Analog RGB, OP03-153 required
FR-21x5 series SXGA Analog RGB, OP03-162 required
FAR-21x7 series SXGA DVI
FEA-2107 SXGA DVI
FEA-2807 SXGA DVI
FCR-21x7 series SXGA DVI
FCR-28x7 series SXGA DVI
MODEL1833C series (NavNet) VGA Analog RGB, OP03-176 required
MODEL1833C-BB series (NavNet) VGA Analog RGB
MODEL1824C series (NavNet vx2) VGA Analog RGB, OP03-176 required
MODEL1824C-BB series (NavNet vx2) VGA Analog RGB
MFD8 (NavNet 3D) VGA DVI
MFD12 (NavNet 3D) SVGA DVI
MFDBB (NavNet 3D)
SVGA
DVIXGA
SXGA
12-24 VDC
MARINE DISPLAY
MU-190HD
RGB
DVI
2 ports
VIDEO (NTSC/PAL)
3 ports
MODEL1824C/1833C/1943C,
FSV-30, FCV-30, FCV-1200L etc.
MFD8/MFD12/MFDBB,
FAR-21X7 series etc.
CCD camera,
DVD recorder, etc.
Environmental category
MU-190HD: Protected from the weather
BRILL CTRL
FAR-1467DS/1467DS-BB (supplied)
vii
EQUIPMENT LISTS
Standard supply
*: See the Installation materials at the back of this manual.
Optional supply
Name Type Code No. Qty Remarks
Display Unit MU-190HD 1 w/ Hard cover
Installation
Materials
CP26-01400 000-016-269 1 set CP26-01402*
Flush Mounting Plate Assy. (CP26-01401,
Code: 001-080-890) 2 pcs.
Cable Assembly (MJ-A3SPF0018-050ZC,
Code: 000-154-025-10) 1 pc.
Accessories FP26-00401 001-080-780 1 set LCD Cleaning Cloth (19-028-3125-5, Code:
100-360-675-10) 1 pc.
Spare Parts SP26-00301 001-080-860 1 set Fuse (FGBO-A 125V 7A PBF, Code: 100-
360-675-10) 3 pcs.
Fuse (FGBO 125V 15A PBF, Code: 000-
155-827-10) 3 pcs.
Name Type Code No. Qty Remarks
Cable Assembly
3COX-2P-6C 5M 001-077-230-10 1 Cable length: 5 m (15 pin D-sub
connector at both ends)
3COX-2P-6C 10M 001-077-220-10 1 Cable length: 10 m (15 pin D-
sub connector at both ends)
DVI-D/D
SINGLELINK5M
000-149-054-10 1 Cable length: 5 m
(with DVI-D connector at both
ends)
DVI-D/D
SINGLELINK10M
000-150-200-10 1 Cable length: 10 m
(with DVI-D connector at both
ends)
Bracket Assembly
(w/knobs)
OP26-5 000-016-270 1 set
Hood Assembly OP26-6 001-080-930 1 set
Flush Mount Kit OP26-7 001-080-940 1 set
Glass Fixing Kit OP26-39 001-567-000 1 set For flush mouting (fixed at rear)/
desktop mounting
Glass Fixing Kit
(front)
OP26-42 001-567-370 1 set For flush mouting (fixed at front)
1
1. MOUNTING, WIRING
1.1 Preparation
Mounting type
You can install the display unit as follows. See the outline drawing at the back of this manual for
mounting dimensions.
Flush mounting, fixed at rear (standard)
Flush mounting, fixed at front (option)
Flush mounting, fixed at rear, with hood (option)
Desktop mounting (option)
Flush mounting a series side by side, fix at rear
Note: The face of the LCD monitor is made of glass. Handle it with care.
Mounting location
When you choose a mounting location, remember the following points:
Make sure the mounting location is strong enough to support the weight of the unit.
Locate the unit away from direct sunlight. An LCD may black out if it is exposed to direct sunlight
for a long time.
Select a location where the display can be easily viewed and the controls can be easily operat-
ed.
Leave enough space around the unit for service and maintenance. See the outline drawing at
the back of this manual for minimum service clearance.
Locate the unit away from areas subject to water splash and rain.
Observe the compass safe distances (see page iii) to prevent interference to a magnetic com-
pass.
Note: If the unit is installed with the screen tilted downwards, the appropriate glass fixing kit (see
“Optional supply” on page vii) must be used.
How to remove/attach the hard cover
Before you install this display unit, remove the hard cover as follows.
Grasping by the hard cover alone may
allow the display unit to fall, resulting in
possible bodily injury or damage to the
equipment.
When lifting the display unit, hold it
together with the hard cover.
CAUTION
CAUTION
1. MOUNTING, WIRING
2
How to remove the hard cover
To attach the hard cover, follow the illustration in the figure below.
How to attach the hard cover
Cable running
Before you install the display unit, run all cables you use. See the interconnection diagram at the
back of this manual.
Pull forward the upper
edge by pressing here
with thumbs.
The upper edge of the hard cover
1. MOUNTING, WIRING
3
1.2 Flush Mounting, Fixed at Rear
Flush mounting, fix at rear is the standard installation method.
1. Make a cutout in the mounting location with the “Flush mounting template” (included).
2. Attach the flush mounting sponges H19 and V19 in the order shown in the figure below.
3. Connect all cables at the back of the display unit. See section 1.7.
442±1 (17.40”)
389±1 (15.32”)
9 (0.35”)
9 (0.35”)
4-ø18 (0.71”)
Flush Mounting Sponge (H19)
for top and bottom
Flush Mounting Sponge (V19)
for right and left
1. MOUNTING, WIRING
4
4. Set the display unit to the cutout.
5. Screw the wing bolts and the wing nuts of the flush mount fixture so that the protector moves
to the mounting plate.
Cutout
Wing Bolt
Wing Nut
Mounting Plate
Protector
Set to the fixture.
Flush Mount Fixture 19
1. MOUNTING, WIRING
5
6. Fasten the flush mount fixture 19 to the right and left sides of the rear of the display unit with
the washer head screws (6 places).
7. Fasten the wing bolts, in the order of the number shown in the figure below so that the protec-
tors touch the mounting panel.
8. Fasten the wing bolts tightly, in the order shown in step 7.
9. Fasten the wing nuts tightly.
Flush Mount Fixture 19Washer Head Screw
Wing Bolt
Wing Nut
Mounting Plate
Protector
Mounting Panel
1. MOUNTING, WIRING
6
1.3 Flush Mounting, Fixed at Front
If you do not have the enough space to fix the display unit from the rear, you can fix it from the
front with the Flush mount kit OP26-7 (option).
Flush Mount Kit OP26-7 (Code: 001-080-940)
1. Make a cutout in the mounting location with the flush mounting template (included).
2. Attach the flush mounting sponges H19 and V19 in the order shown in the figure below.
Name Type Code No. Qty.
Flush Mounting Panel (19) OP26-7-1 001-080-980-00 1
Washer Head Screw M4x10 000-163-836-10 8
Self Tapping Screw 5x20 000-162-609-10 4
Flush Mounting Template C42-00911 000-172-638-10 1
448 (17.64”)
4-
ø
18 (0.71”)
395 (15.55”)
9 (0.35”)
460
±
0.5 (18.11”)
407
±
0.5 (16.02”)
9 (0.35”)
Pilot hole
for mounting from the front
Flush Mounting Sponge (H19)
for top and bottom
Flush Mounting Sponge (V19)
for right and left
1. MOUNTING, WIRING
7
3. Attach the flush mounting panel to the display unit from the rear with the washer head screws
(8 places).
4. Connect all cables at the back of the display unit. See section 1.7.
5. Set the display unit assembly prepared at the step 3 to the cutout for the mounting location.
6. Fix the display unit to the cutout with the self tapping screws (4 places).
Flush Mounting Panel (19)
Washer Head Screw
Self Tapping Screw
1. MOUNTING, WIRING
8
1.4 Flush Mounting, Fixed at Rear, with hood
You can attach a hood when flush mounting the unit from the rear, using the hood assembly
OP26-6 (option).
Hood Assembly OP26-6 (Code: 001-080-930)
1. Make a cutout in the mounting location with the flush mounting template (included).
2. Fix the hood fixing plates to the right and left of the display unit with the flat head screws (6
places).
Name Type Code No. Qty.
Hood (19) Assembly OP26-6-1 001-080-970-00 1
Flush Mounting Sponge (V19) 26-005-3124 100-351-560-10 2
Hood Fixing Plate 19 26-005-3302 100-351-611-10 2
F-Mount Hood Gasket 19 26-005-3305 100-351-620-10 2
Knob M4 03-163-2303 100-343-602-10 4
Flat Head Screw M3x8 000-172-167-10 6
Flush Mounting Template C42-00910 000-172-637-10 1
446±1 (17.56”)
389±1 (15.32”)
9 (0.35”)
4-ø18 (0.71”)
9 (0.35”)
Hood Fixing Plate 19
Flat Head Screw
1. MOUNTING, WIRING
9
3. Attach the hood gaskets to the top and bottom brims. Then, attach the flush mounting sponge
(V19) to the right and left brims, of the display unit from the rear side.
4. Follow steps 3 to 9 in section 1.2 to fix the display unit to the mounting location.
5. Loosely fix the knobs (4 pcs.) to the hood fixing plate.
6. Slide the cutouts of the hood assembly to the knobs.
F-mount Hood Gasket 19
for top and bottom
Flush Mounting Sponge (V19)
for left and right
Knob (4 pcs.)
Hood (19) Assembly
Hood Fixing Plate 19
Cutout (4 places)
1. MOUNTING, WIRING
10
7. Press the top of the hood to fit the knobs in the cutouts.
8. Fix the hood assembly with the knobs tightly (4 places).
1.5 Desktop Mounting
You can fix the display unit to a desktop, using the bracket assembly OP26-5 (option).
Bracket Assembly OP26-5 (Code: 000-016-270)
Name Type Code No. Qty.
Mounting Bracket (19) OP26-5-1 001-080-910-00
1
Bracket Support w/knobs OP26-5-2 001-080-920-00
Self-Tapping Screw 5x20 000-162-608-10 4
Binding Head Screw M4x10 000-172-165-10 9
Press
Press
1. MOUNTING, WIRING
11
1. Loosen the knobs of the bracket support to separate the mounting bracket from the bracket
support.
2. Set the mounting bracket to the mounting location with four self-tapping screws.
Mounting Bracket (19)
Bracket Support
Knob
Self-Tapping Screw
5x20
Mounting Bracket (19)
1. MOUNTING, WIRING
12
3. Attach the bracket support to the rear of the display unit with the binding head screws (9 plac-
es).
4. Connect all cables at the back of the display unit. See section 1.7.
5. Loosen the knobs of the bracket support and set them in the notches on the mounting bracket.
6. Adjust the angle of the display unit and fix the knobs tightly.
Binding Head Screw
Bracket Support
Screw (9 places)
Rear of the display unit
Mounting Bracket (19)
Knob
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81

Furuno MU190HD ユーザーマニュアル

カテゴリー
テレビ
タイプ
ユーザーマニュアル

他の言語で