Furuno MU190 インストールガイド

カテゴリー
テレビ
タイプ
インストールガイド
www.furuno.com
MONITOR UNIT
OPERATOR'S MANUAL
Model
表示部
取扱説明書
MU-190
本書の無断複写複製(コピー)は特定の
場合を除き、当社権利侵害になります。
( ETMI) MU-190
Pub. No. OMC-44670-E3
Printed in Japan
・ 機器の修理・使用方法等に関するお問い合わせは、お買い上げの販売店・代理店、最寄りの
  当社支店・営業所あてへお願いします。
(Elemental Chlorine Free)
The paper used in this manual
is
elemental chlorine free.
FURUNO Authorized Distributor/Dealer お問い合わせは
: MAY 2011
: APR. 22, 2020
A
E3
00017448914
i
IMPORTANT NOTICES
General
This manual has been authored with simplified grammar, to meet the needs of international users.
The operator of this equipment must read and follow the instructions in this manual.
Wrong operation or maintenance can void the warranty or cause injury.
Do not copy any part of this manual without written permission from FURUNO.
If this manual is lost or worn, contact your dealer about replacement.
The contents of this manual and the equipment specifications can change without notice.
The example screens (or illustrations) shown in this manual can be different from the screens you
see on your display. The screens you see depend on your system configuration and equipment
settings.
Save this manual for future reference.
Any modification of the equipment (including software) by persons not authorized by FURUNO will
void the warranty.
The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.
- Name: FURUNO EUROPE B.V.
- Address: Ridderhaven 19B, 2984 BT Ridderkerk, The Netherlands
All brand, product names, trademarks, registered trademarks, and service marks belong to their
respective holders.
How to discard this product
Discard this product according to local regulations for the disposal of industrial waste. For disposal in
the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the
correct method of disposal.
How to discard a used battery
Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter
on Maintenance. If a battery is used, tape the + and - terminals of the battery before disposal to pre-
vent fire, heat generation caused by short circuit.
In the European Union
The crossed-out trash can symbol indicates that all types of batteries
must not be discarded in standard trash, or at a trash site. Take the
used batteries to a battery collection site according to your national
legislation and the Batteries Directive 2006/66/EU.
In the USA
The Mobius loop symbol (three chasing arrows) indicates that
Ni-Cd and lead-acid rechargeable batteries must be recycled.
Take the used batteries to a battery collection site according to
local laws.
In the other countries
There are no international standards for the battery recycle symbol. The number of symbols can in-
crease when the other countries make their own recycle symbols in the future.
Cd
Ni-Cd Pb
ii
SAFETY INSTRUCTIONS
Indicates a condition that can cause death or serious
injury if not avoided.
Indicates a condition that can cause minor or moderate
injury if not avoided.
Use the proper fuse.
Use of a wrong fuse can cause fire or
damage to the equipment.
Handle the LCD monitor with care.
The face of the LCD monitor is made
of glass.
Injury may result if the
glass breaks.
Read these safety instructions before you operate the equipment.
WARNING
CAUTION
Warning, Caution
Prohibitive Action
Mandatory Action
Safety Instructions for the Operator
WARNING
WARNING
WARNING
WARNING
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury
can result.
Do not place any object near the
exhaust or intake vent.
Fire may result.
CAUTION
CAUTION
Do not connect/disconnect the signal
cable while turning the power on.
The unit may be damaged.
Immediately turn off the power at the
switchboard if water leaks into the
equipment or something is dropped
into the equipment.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Immediately turn off the power at the
switchboard if the equipment is
emitting smoke or fire.
Continued use of the equipment can
cause fire or electrical shock. Contact a
FURUNO agent for service.
Turn off the power immediately if you
feel the equipment is behaving
abnormally.
Turn off the power at the switchboard if
the equipment becomes abnormally
warm or is emitting odd noises. Contact
a FURUNO dealer or agent for advice.
SAFETY INSTRUCTIONS
iii
Safety Instructions for the Installer
WARNING
WARNING
CAUTION
CAUTION
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage to the
equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
MU-190
Standard
compass
Steering
compass
1.65 m 1.05 m
WARNING
㆙࿌
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
ឤ㟁䛾ᜍ䜜䛒䜚䚹
䝃䞊䝡䝇䝬䞁௨እ䛾᪉䛿䜹䝞䞊䜢㛤䛡
䛺䛔䛷ୗ䛥䛔䚹ෆ㒊䛻䛿㧗㟁ᅽ㒊ศ䛜
ᩘከ䛟䛒䜚୓୍䛥䜟䜛䛸༴㝤䛷䛩
Warning Labels
Warning labels are attached to the equipment. Do not remove the labels. If a label is missing or damaged, contact a
FURUNO agent or dealer about replacement.
Name: Warning Label 1
Type: 86-003-1011-3
Code No.: 100-236-233-10
Name: High Voltage Warning Label
Type: 16-018-3206-0
Code No.: 100-297-770-10
The TFT LCD is constructed using the latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01% of the pixels may drop out or
blink, however this is not an indication of malfunction.
About the TFT LCD
About the TFT LCD
About the TFT LCD
iv
TABLE OF CONTENTS
Note: This manual contains both English and Japanese instructions. The Installation
Materials, Outline Drawings, and Interconnection Diagram are located at the back of this
manual.
FOREWORD ................................................................................................................. v
SYSTEM CONFIGURATION ....................................................................................... vi
EQUIPMENT LISTS.................................................................................................... vii
1. MOUNTING, WIRING............................................................................................. 1
1.1 Preparation................................................................................................................. 1
1.2 Flush Mount, Fixed at Front ....................................................................................... 2
1.3 Flush Mount, Fixed at Front, with Hood ..................................................................... 3
1.4 Flush Mount, Fixed at Rear........................................................................................ 5
1.5 Flush Mount, Fixed at Rear, with Hood...................................................................... 7
1.6 Tabletop Mount .......................................................................................................... 8
1.7 Flush Mount a Series Side by Side .......................................................................... 10
1.8 Wiring .......................................................................................................................11
2. ADJUSTMENTS................................................................................................... 12
2.1 Installation Settings .................................................................................................. 12
2.2 RGB/DVI Setting (For Non-SOLAS)......................................................................... 14
2.3 Video Composite Signal Setting (For Non-SOLAS) ................................................. 16
2.4 The Menu Window Setting (For Non-SOLAS) ......................................................... 17
2.4.1 How to adjust the menu window....................................................................... 17
2.4.2 How to change the signal name ....................................................................... 18
3. OPERATION ........................................................................................................ 19
3.1 Controls.................................................................................................................... 19
3.2 How to Turn the Power On/Off................................................................................. 19
3.2.1 Turn the power on/off........................................................................................ 19
3.2.2 Unlock the key operation .................................................................................. 20
3.3 How to Adjust the Display Brilliance......................................................................... 20
3.4 How to Select the Source for Main Picture .............................................................. 21
3.5 How to Display the PIP Window............................................................................... 21
3.6 SYSTEM Menu ........................................................................................................ 21
3.6.1 How to set the auto dimmer.............................................................................. 21
3.6.2 How to clear the memory.................................................................................. 22
4. MAINTENANCE, TROUBLESHOOTING............................................................. 23
4.1 Maintenance............................................................................................................. 23
4.2 Troubleshooting ....................................................................................................... 24
4.3 Parts Location and Parts List ................................................................................... 24
SPECIFICATIONS .................................................................................................. SP-1
PACKING LISTS ...................................................................................................... A-1
OUTLINE DRAWINGS.............................................................................................. D-1
INTERCONNECTION DIAGRAM ..............................................................................S-1
v
FOREWORD
A Word to the Owner of the MU-190
FURUNO Electric Company thanks you for purchasing the MU-190 19” Monitor Unit. We are con-
fident you will discover why the FURUNO name has become synonymous with quality and reliabil-
ity.
Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reli-
ability throughout the world. This dedication to excellence is furthered by our extensive global net-
work of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine envi-
ronment. However, no machine can perform its intended function unless properly installed and
maintained. Please carefully read and follow the operation, installation and maintenance proce-
dures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our goal.
Thank you for considering and purchasing FURUNO.
Features
The main features of the MU-190 are as shown below.
Program
xx: minor change
CE declaration
With regards to CE declarations, please refer to our website (www.furuno.com), for further infor-
mation about RoHS conformity declarations.
Selectable screen from RGB (1 port), Digital (2 ports) or Composite (1 port).
Main or remote display for radars, video sounders, sonars, plotter. For the connectable equipment,
see the SYSTEM CONFIGURATION on page vi.
High resolution display of 1280 x 1024 (SXGA).
Automatic brilliance adjustment by the light sensor.
• Picture-in-picture function.
Power on/off automatically through the DVI signal.
Program Name Version Date of Change
APR PROGRAM 2651020-01.xx May. 2011
FPGA PROGRAM 2651021-01.xx May. 2011
You can see these program numbers on the [SYSTEM] menu (see section 3.6). To open the [SYS-
TEM] menu, unlock the key operation (see paragraph 3.2.2).
Note: When you connect the monitor unit to FMD-3200*, FAR-21x7 series, FEA-2107, FCR-21x7
series, FCR-21x9 series or FAR-32x0 series lock the key operation (see paragraph 3.2.2) after con-
firming the program numbers.
*: To connect the monitor unit to the FMD-3200, the program version for the APR program must be
2651020-01.02 or higher.
vi
SYSTEM CONFIGURATION
Example: Connectable equipment
Note 1: Landscape orientation only.
Note 2: *: When inputting VGA, SVGA or XGA, a circle may be displayed as an ellipse because
the aspect ratio differs (see "DISP MODE*" on page 15).
Equipment Resolution Signal
FCV-1200L/1200LM VGA* Analog RGB, via IF-8000
FSV-24/24S SXGA Analog RGB
FSV-30/30S SXGA Analog RGB
FSV-84/84L SXGA Analog RGB
FSV-85/85L SXGA Analog RGB
FCV-30 SXGA Analog RGB
FAR-21x7 SXGA DVI
FEA-2107 SXGA DVI
FCR-21x7 SXGA DVI
FMD-3200 SXGA DVI
FCR-21x9 UXGA DVI
FAR-32x0 SXGA DVI
MFDBB (NAVnet 3D)
SVGA*
DVIXGA*
SXGA
MONITOR UNIT
MU-190
100-230 VAC
RGB
DVI (2 ports)
VIDEO (NTSC/PAL)
RS-232C
FSV-30/30S, etc.
FAR-21x7, FEA-2107,
FCR-21x7, FAR-32x0, etc.
CCD camera, DVD recorder, etc.
Environmental category
MU-190: Protected from the weather
FEA-2107, FCR-21x7, etc.
RS-485
FMD-3200, FCR-21x9, FAR-32x0, etc.
vii
EQUIPMENT LISTS
Standard supply
Optional supply
Name Type Code No. Qty Remarks
Monitor Unit MU-190 - 1
Installation
Materials
CP26-01600 000-019-210 1 set Installation Materials (CP26-01601, Code
No.: 001-116-250, See page A-3.)
Cable Assembly (DVI-D/D S-LINK 5M,
Code No.: 001-132-960-10)
Accessories FP26-00401 001-080-210 1 set LCD Cleaning Cloth (19-028-3125-6,
Code No.: 100-360-676-10)
Spare Parts SP26-00801 001-468-150 1 set Glass Tube Fuse (FGBO-A 250V 5A PBF,
Code No.: 000-155-840-10) 3 pcs.
Name Type Code No. Remarks
Cable Assembly 3COX-2P-6C
5M
001-077-230-10 Cable length: 5 m (15 pin D-sub connector at
both ends)
3COX-2P-6C
10M
001-077-220-10 Cable length: 10 m (15 pin
D-sub connector at both ends)
DVI-D/D
S-LINK 5M
001-132-960-10 Cable length: 5 m
(with DVI-D connector at both ends)
DVI-D/D
S-LINK 10M
001-133-980-10 Cable length: 10 m
(with DVI-D connector at both ends)
Bracket Assembly
(w/knobs)
OP26-5 000-016-270
Hood Assembly OP26-6 001-080-930
Dust Cover 26-007-1201 001-116-260-10
Flush
Mount Kit
OP26-12 001-116-280 Flush Mounting Sponge H 19
(26-005-3123, Code No.: 100-351-550-10)
Flush Mounting Sponge V 19
(26-005-3124, Code No.: 100-351-560-10)
Washer Head Screw B
(M4x10, Code No.: 000-163-836-10)
Flush Mount Fixture 19
(CP26-01401, Code No.: 001-080-890)
Note: The quantity of each part depends on
the number of units connected.
OP26-13
(Two units
installed side
by side)
001-116-290
OP26-14
(Three units
installed side
by side)
001-116-300
Connection Stand
(19)
OP26-20 001-139-300
Bracket Assembly OP26-21 001-139-310
Hood (19) Assem-
bly
OP26-24 001-139-370
Monitor
Replacement Kit
OP26-22 001-139-320 For flush mount
OP26-23 001-139-360 For tabletop mount
OP26-26 001-139-390 For hood mount
Glass Fixing Kit OP26-39 001-567-000 For flush mouting (fixed at rear)/
tabletop mounting
Glass Fixing Kit
(front)
OP26-40 001-567-010 For flush mouting (fixed at front)
1
1. MOUNTING, WIRING
1.1 Preparation
Mounting method
You can install the monitor unit as follows. See the outline drawings at the back of this manual for
mounting dimensions.
Flush mount, fixed at front (standard)
Flush mount, fixed at front, with hood (option)
Flush mount, fixed at rear (option)
Flush mount, fixed at rear, with hood (option)
Tabletop mount (option, hood-mountable)
Flush mount a series side by side, fixed at rear
Note 1: The face of the LCD is made of glass. Handle it with care.
Note 2: For flush mount, take care so that the monitor unit does not fall during the installation.
Mounting location
Select a mounting location considering the following points. This equipment is free from electro-
magnetic fields.
Make sure the mounting location is strong enough to support the weight of the unit.
Locate the unit away from direct sunlight. An LCD may darken if it is exposed to direct sunlight
for a long time.
Select a location where the screen can be easily viewed and the controls can be easily operat-
ed.
Leave enough space around the unit for service and maintenance. See the outline drawings at
the back of this manual for minimum service clearance.
Locate the unit away from areas subject to water splash and rain.
Observe the compass safe distances (see page iii) to prevent interference to a magnetic com-
pass.
Note: If the unit is installed with the screen tilted downwards, the appropriate glass fixing kit (see
“Optional supply” on page vii) must be used.
Run cables before installing the monitor unit
Run all cables before you install the monitor unit. See the interconnection diagram at the back of
this manual.
1. MOUNTING, WIRING
2
1.2 Flush Mount, Fixed at Front
Flush mount, fix at front is the standard installation method.
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Attach the flush mounting
sponges H19 and V19 to the
back of the monitor unit in the
order shown in the figure at
right.
3. Attach the flush mount panels 19 to the monitor unit from the rear with the binding head
screws (M4x10, 6 pcs., supplied).
Note: Attach the flush mount panels to both sides of the monitor unit with no gap.
4. Connect all cables at the back of the monitor unit. See section 1.8.
5. Set the monitor unit assembly to the cutout.
6. Fix the monitor unit to the cutout with the self-tapping screws (5x20, 4 pcs., supplied).
Binding Head Screw
Flush Mount Panel 19
Self-Tapping Screw
(4 places)
1. MOUNTING, WIRING
3
7. Set the masking panel to each side of the monitor unit.
How to attach or detach the masking panel for 19” LCD
Do the following to attach or detach the masking panel for 19” LCD.
1.3 Flush Mount, Fixed at Front, with Hood
The flush mount, fixed at front method allows you to attach a hood (19) assembly OP26-24 (op-
tion) to the monitor unit.
Hood (19) assembly OP26-24 (Code No.: 001-139-370)
Name Type Code No. Qty
Hood (19) Assembly OP26-6-1 001-080-970 1
Knob M4 03-163-2303 100-343-602-10 4
Hood Fixing Plate (19) 26-007-1128 100-366-350-10 2
Binding Head Screw M3x8 000-172-166-10 6
Masking Panel for 19” LCD
Tab A
Tab B
Front side of
monitor unit
Set the masking panel for 19” LCD to each side
of the monitor unit. Attach each tab A to the
monitor unit. Be careful not to break the tabs.
Set tab B to
the edge of
the monitor
unit.
Monitor unit
To attach, follow order of right arrow (→). To detach, follow order of left arrow (←).
Masking
panel
→→
1
2
Reverse view of masking panel for 19” LCD
a
b
c
Attach: Push the
masking panel for 19”
LCD in the direction
, rotate the panel
toward the monitor
unit, then set each tab
A one by one (three
places of a, b and c) .
1
2
Detach: Push the masking panel for 19”
LCD in the direction 1, then release each
tab A one by one
(three places of a, b and c)
in the direction 2.
1. MOUNTING, WIRING
4
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Follow steps 2 to 6 in section 1.2.
3. Loosely fix the knobs (4 pcs.) to the hood fixing plates (19) from inside the plates.
4. Remove the binding head screws (M3x5, 6pcs.) and the side panel bases (6 pcs.) from the
flush mount panels 19 attached to the monitor unit.
5. Attach the hood fixing plates (19) and the side panel bases to the right and left sides of the
monitor unit with the binding head screws (M3x8, 6pcs.)
6. Press and rub folds on the hood with your hands to make creases clearly. The degree of
creases should be within 90° when the hood is opened.
Hood Fixing Plate (19)
Knob
Side Panel Base (6 pcs.)
Binding Head Screw (6 pcs.)
Flush Mount Panel 19
Side Panel Base (6 pcs.)
Binding Head Screw (6 pcs.)
Hood Fixing Plate (19)
Hood
Correct
Incorrect,
insufficient
Press and move your hands to
upward and downward several times.
1. MOUNTING, WIRING
5
7. Set the cutouts of the hood (19) assembly to the knobs on the hood fixing plates (19).
8. Press the top of the hood (19) assembly to set the knobs in the cutouts.
9. Set the hood (19) assembly with the knobs tightly (4 pcs.).
1.4 Flush Mount, Fixed at Rear
The flush mount, fixed at rear method requires the flush mount kit OP26-12 (option, see page vii).
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Attach the flush mounting sponges
H 19 and V 19 to the back of the
monitor unit in the order shown in
the figure at right.
Hood (19) Assembly
Knob (4 pcs.)
Hood Fixing Plate 19
Cutout (4 places)
Press
Press
Flush Mounting
Sponge H 19 for
top and bottom
Flush Mounting
Sponge V 19 for
left and right
1. MOUNTING, WIRING
6
3. Screw the wing bolts and the wing nuts of the flush mount fixture 19 so that the protector for
screw moves to the fixing plate.
4. Connect all cables at the back of the monitor unit. See section 1.8.
5. Set the monitor unit to the cutout.
6. Fasten the flush mount fixture 19 to the right and left sides of the rear of the monitor unit with
the washer head screws B (6 pcs.).
7. Fasten each wing bolt in the order shown in the figure below so that the protector for screw
touches the mounting panel.
8. Fasten the wing bolts tightly to secure the monitor unit.
9. Fasten the wing nuts tightly.
Flush Mount Fixture 19
Wing Bolt
Fixing Plate
Protector for
Screw
Move to the fixing plate.
Wing Nut
Washer Head Screw B
(6 places)
Flush Mount Fixture 19
Mounting
Panel
Fixing Plate
Wing Bolt
Wing Nut
Protector for Screw
1. MOUNTING, WIRING
7
1.5 Flush Mount, Fixed at Rear, with Hood
The flush mount, fixed at rear method allows you to attach a hood assembly OP26-6 (option) to
the monitor unit.
Hood assembly OP26-6 (Code No.: 001-080-930)
1. Use the flush mounting template (supplied) to make a cutout in the mounting location.
2. Fix the hood fixing plates 19 to the right and left sides of the monitor unit with the flat head
screws (6 pcs.).
3. Attach the F-mount hood packing 19 to the top and bottom brims. Then, attach the flush
mounting sponge V 19 to the right and left brims of the monitor unit from the rear side.
4. Follow steps 3 to 9 in section 1.4 to fix the monitor unit to the mounting location.
5. Loosely fix the knobs (4 pcs.) to the hood fixing plate 19 from inside the plate.
Name Type Code No. Qty
Hood (19) Assembly OP26-6-1 001-080-970 1
Flush Mounting Sponge V 19 26-005-3124 100-351-560-10 2
Hood Fixing Plate 19 26-005-3302 100-351-611-10 2
F-Mount Hood Packing 19 26-005-3305 100-351-620-10 2
Knob M4 03-163-2303 100-343-602-10 4
Flat Head Screw M3x8 000-172-167-10 6
Flush Mounting Template C42-00910 000-172-637-10 1
Hood Fixing Plate 19
Flat Head Screw
F-Mount Hood
Packing 19 for
top and bottom
Flush Mounting
Sponge V 19 for
left and right
1. MOUNTING, WIRING
8
6. Set the cutouts of the hood (19) assembly to the knobs on the hood fixing plates 19.
7. Press the top of the hood assembly to set the knobs in the cutouts.
8. Set the hood assembly with the knobs tightly (4 pcs.).
1.6 Tabletop Mount
You can fix the monitor unit to a tabletop, using the bracket assembly OP26-5 (option).
Bracket Assembly OP26-5 (Code No.: 000-016-270)
1. Loosen the knobs of the bracket support to separate the mounting bracket (19) from the brack-
et support.
Name Type Code No. Qty
Mounting Bracket (19) OP26-5-1 001-080-510 1
Bracket Support w/Knobs OP26-5-2 001-176-060 1
Self-Tapping Screw 5x20 000-162-608-10 4
Binding Head Screw M4x10 000-172-165-10 9
Hood Fixing Plate 19
Cutout (4 places)
Hood (19) Assembly
Knob (4 pcs.)
Press
Press
Knob
Mounting Bracket (19)
Bracket Support w/Knobs
1. MOUNTING, WIRING
9
2. Set the mounting bracket to the mounting location with four self-tapping screws.
3. Attach the bracket support to the rear of the monitor unit with the binding head screws (9 pcs.).
4. Connect all cables at the back of the monitor unit. See section 1.8.
5. Loosen the knobs of the bracket support and set knobs in the notches on the mounting brack-
et.
6. Adjust the angle of the monitor unit and fix the knobs tightly.
How to attach the hood
You can attach a hood to the tabletop-mounted monitor unit, using the hood assembly OP26-6
(option).
1. Follow steps 1 to 3 in section 1.6.
2. Fix the hood fixing plates 19 to the right and left of the monitor unit with the flat head screws
(6 places). (See step 2 in section 1.5.)
3. Follow steps 4 to 5 in section 1.6.
4. Follow steps 5 to 8 in section 1.5.
Self-Tapping Screw
(4 places)
Mounting Bracket (19)
Bracket Support w/Knobs
Binding Head
Screw
Rear view
Binding Head Screw (9 places)
Mounting Bracket (19)
Knob
1. MOUNTING, WIRING
10
1.7 Flush Mount a Series Side by Side
You can flush mount two or three monitor units side by side, using the optional flush mount kit
OP26-13 for two monitor units or OP26-14 for three monitor units (see page vii).
1. Make a cutout in the mounting location as shown below (see page D-4).
2. Follow steps 2 to 5 in section 1.4 to set the two or three monitor units in the mounting location.
3. Attach the flush mount fixtures 19 with the washer head screws B to join the two or three mon-
itor units.
4. Fasten two or three monitor units tightly. See steps 7 to 9 in section 1.4.
892
±
1
389
±1
(9)
4-
Ø
18
(9)
1342
±
1
389
±1
(9)
4-
Ø
18
(9)
For two monitor units
For three monitor units
Join the two monitor units with the
flush mount fixtures 19 (4 pcs.).
Join the three monitor units with the
flush mount fixtures 19 (6 pcs.).
1. MOUNTING, WIRING
11
1.8 Wiring
Refer to the figure below and the interconnection diagram at the back of this manual to connect
cables.
Connector
*1: Attach a crimp-on lug (inner dia. φ4) for monitor unit side. Make the length of the ground wire
as short as possible.
*2: Slide switch
ON (upward): Allow digital signal from external equipment to control on/off of the monitor unit.
OFF (downward): Set to OFF for analog RGB signal.
Note: Turn the slide switch off when you connect equipment to both the DVI and RGB ports.
*3: BRILL CTRL port
No use. Do not remove the sticker from the connector.
How to fix power cable
Fix the power cable with the cable clamp to prevent it from loosening.
FSV-84/84L
FSV-30/S-BB
FSV-24/S-BB
FCV-30
FCV-1200L/M
FSV-84/84L
FSV-30/S-BB
FSV-24/S-BB
FCV-30
FCV-1200L/M
FAR-21x7
FEA-2107
FCR-21x7
FMD-3200
FCR-21x9
FAR-32x0
FAR-21x7
FEA-2107
FCR-21x7
FMD-3200
FCR-21x9
FAR-32x0
The bottom of the rear of the monitor unit
RGB signal
3COX-2P-6C
5 m/10 m (option)
RGB signal
3COX-2P-6C
5 m/10 m (option)
RGB signal
3COX-2P-6C
5 m/10 m (option)
Digital signal
DVI-D/D S-LINK
5 m (standard)/
10 m (option)
Digital signal
DVI-D/D S-LINK
5 m (standard)/
10 m (option)
Digital signal
DVI-D/D S-LINK
5 m (standard)/
10 m (option)
Composite
signal cable
Composite
signal cable
Composite
signal cable
CCD camera
DVD recorder
CCD camera
DVD recorder
CCD camera
DVD recorder
BRILL CTRL
port *
3
BRILL CTRL
port *
3
BRILL CTRL
port *
3
IV-1.25 sq
(local supply) *
1
IV-1.25 sq
(local supply) *
1
IV-1.25 sq
(local supply) *
1
To ground
terminal on hull
DPYC-1.5
(or equivalent)
DPYC-1.5
(or equivalent)
DPYC-1.5
(or equivalent)
100-230 VAC
Slide
switch *
2
Slide
switch *
2
Slide
switch *
2
Power
switch
Fuse
RS-232C cable
(Max. 10 m)
or
RS-485 cable
(Max. 10 m)
RS-232C cable
(Max. 10 m)
or
RS-485 cable
(Max. 10 m)
RS-232C cable
(Max. 10 m)
or
RS-485 cable
(Max. 10 m)
DPYC-1.5
φ = 11.7 mm
Armor
Sheath
Conductor
S = 1.5 mm
2
φ = 1.56 mm
Attach the Terminal Board Gear Cover
again after connecting cables.
FEA-2107, FCR-21x7
(with RS-232C)
or
FMD-3200, FCR-21x9,
FAR-32x0
(with RS-485)
FEA-2107, FCR-21x7
(with RS-232C)
or
FMD-3200, FCR-21x9,
FAR-32x0
(with RS-485)
MU-190
Cable
clamp
Length: 40 mm
Length: 60 mm
Local supply
Replace MU-201CE with MU-190
Cut the connector of the power
cable (15-565, supplied on the
MU-201CE). Attach a crimp-on lug
(supplied on the MU-190) to each
cable core then connect the
cables as in the figure at right.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Furuno MU190 インストールガイド

カテゴリー
テレビ
タイプ
インストールガイド

他の言語で