2. ATOMRC
  3. B09LCG99J2
B09LCG99J2

ATOMRC B09LCG99J2 ユーザーマニュアル

  • ATOMRC Dolphin ドローンのユーザーマニュアルの内容を読み終えました。このドローンは、前掠式翼とV字型尾翼を採用し、安定した飛行性能を実現しています。組み立て方法から飛行方法、VTXの設定など、このマニュアルに記載されているあらゆる内容について質問にお答えできますので、お気軽にご質問ください。
  • Dolphin ドローンの重心はどこにありますか？
    電調のキャリブレーション方法は？
    VTX（ビデオトランスミッター）の天線はいつ取り付けますか？
User Manual
Dolphin
海豚
www.atomrc.com/pages/download
Introduction/简介
The Dolphin is sweep forward fly wing, with elegant design, the dolphin can
fly stable both on high speed and low speed, the large fuselage can give use
lots of space to install the electronics, the detachable wing made the wing
easy for transport, V tail made the wing more stable for crusing.
Specifications/规格
1
Wingspan/翼展: 845mm
Length/⻓度: 710mm
WingArea/翼⾯积: 15.24d㎡
Material/材料: EPP
Recommend Motor/推荐电机: 2306 2000KV
Recommend ESC/推荐电调: 30A 2~4S
Recommend Propeller/推荐螺旋桨: 7040
Servo/舵机: 9g Servo*2PCS
Recommned Battery/推荐电池: 4S 1800~2200mAh Lipo
Specifications/规格
海豚是前掠式⻜翼布局⻜机，针对FPV⻜⾏所搭载的设备载重，极佳的优化了异形和装配空间。
能够满⾜⾼速⻜⾏的同时，低速也能获得⾮常优秀的滑翔性能。可拆卸的机翼使机翼便于运输，
V型尾翼使机翼在巡航时更加稳定。
2
VersionDescription/版本说明
KIT Contents
A B C
D E G HF
A：Fuselage
上机身
D：Tail
垂尾
G：Nose
尖机头
B：Fuselage
下机身
E：Front Hatch
前舱盖
H：Gopro Hatch
Gopro机头
C：Wing
机翼
F：Rear Hatch
后舱盖
3
KITLiteInstallation/KITLite安装指南
Install the standoff and nuts, need glue the nylon screw under the board.
安装机舱螺⺟及螺丝，机舱⽊⽚底部螺丝需先⽤胶⽔固定。
Glue the gopro mount plate, then glue the fuselage.
Install the battery strap , glue the battery mount board to the fuselage.
Install the Camera mount plate, and the V taill.
4
1
4
2
3
粘接GOPRO安装⽊板，然后粘接上下机身。
安装电池固定⽊⽚，安装舱盖扣。
安装机头相机安装⽚，粘接V尾。
Install side plate of the wing, then install the control horn .
安装机翼侧边⽊⽚，机翼舵⻆。
Glue the plastic protection parts on the wing and the bottom .
粘接机翼机腹塑料保护⽚。
5
5
6
7
Install the magnet on the hatch, glue the sharp nose.
安装各个舱盖磁铁，粘接尖机头。
6
2
4
Install the motor and ESC.
安装电机电调。
1
KIT/PNP/FPVInstallation/安装指南
3
User can choose carbon plate to install the camera or just use foam to fill.
⻜机机头位置，可以选择安装摄像头固定碳⽚或者泡沫填充。
Install the servo and push rods, then install the rudder.
将舵机安装到垂尾、平尾，居中调试后，安装拉杆。粘合左右垂尾。
Install the wing to the fuselage.
将左右机翼安装到机身。
7
5
When Gopro is installed, adjust battery slider to adjust balance.
安装Gopro时，需要将电池安装到后⾯，通过滑块调平。
To install Gopro, use rubber band to lock the gopro then install the hatch.
若安装GOPRO，需⽤橡⽪筋固定住GOPRO，然后盖上机头相机盖。
6
7
The CG is marked under the wing, you can move
the CG 3-4mm to get better control.
海豚的重⼼点、标记在机翼底部，
默认更适合新⼿更易起⻜，在默认重⼼点完成⾸⻜后，
你可将重⼼点往前移3~4mm，从⽽获得更好的⼿感。
CG CG
Install the Nose and Cam.
安装摄像头机头。
8
ESC /电调接线图Wiring Diagram
ESCInformation/电调说明
1.The ESC included with the model has a safe start.If the motor battery is
connected to the ESC and the throttle stick is not in the low throttle or off
position,the motor will not start untill the throttle stick is moved to the low
throttle or off position.
2.Power on the ESC(The ESC must connect to the motor and Receiver).
The motor will emit a series of beeps, after the beeps, set the the throttle
stick the the minimum, the motor will emit a series beep again. now the ESC
calibration is done.
1.电调具有安全启动设置，当电机、电池连接电调后，电调信号未处于最低位置，
电调输出不会启动。
2.电调油⻔校准：请先拆卸螺旋桨，将油⻔摇杆移动到最⾼位置后通电，当哔哔
声结束后，迅速将油⻔摇杆移动到最低位置，哔哔声⾳结束，油⻔校准成功。
100
+
-
G5V
s
MOTOR
电源正负极，VCC/GND
5V3A输出，Output 5V3A
油⻔信号，Throttle
油⻔信号地，Throttle GND
Voltage input/电压输⼊范围: 2~4S Lipo
Max Current/最⼤电流: 35A
Output/输出：Built in 5V 3A BEC/内置5V 3A BEC
Throttle calibration /电调油⻔校准
8
1.Hold button 3 seconds into setting mode.
2.In setting mode. short press the button to change band.
3.Then hold button 3 seconds into CH setting mode, short press button to change CH.
4.Hold button 3 second to get into Power setting mode, there is short bar on LED, short
press to switch power, 1 bar means 200mW, 2 bar means 800mW, 3 bar means 1500mW.
1.⻓按设置按键三秒，进⼊波段设置模式。
2.在设置模式下，短按按键切换波段。
3.再次⻓按按键三秒钟，进⼊频道切换模式，短按按键切换频道。
4.再次⻓按按键三秒钟，进⼊切换功率模式，短按按键切换功率，数码管⼀条为200mw，两条
为800mw, 三条为1500mw。
Please download the latest user manual at
www.atomrc.com/pages/download
GND
VIDEO
5V
AUDIO
VIDEO
GND
5V OUT
GND
VCC
Please make sure antenna is installed before power on, otherwise the VTX will fried!!!
图传发射机通电前务必确认天线已安装妥当，否则发射线会烧毁!!!
Band
Channel
1
2
3
4
5
6
7
8
Band A
5865
5845
5825
5805
5785
5765
5745
5725
Band B
5733
5752
5771
5790
5809
5828
5847
5866
Band E
5705
5685
5665
5645
5885
5905
5925
5945
Airwave/FS
5740
5760
5780
5800
5820
5840
5860
5880
Race Band
5658
5695
5732
5769
5806
5843
5880
5917
L Band
5362
5399
5436
5473
5510
5547
5584
5621
Voltage input/电压输⼊范围: 2~6S Lipo Power/功率: 200/800/1500mw Switchable
Power consumption/功耗: 9V 1.1A Frequency/频率:5.3~5.9Ghz
VTX Tx15 Uermanual/图传说明书
Tx15 Wiring Tx15图传接线图Diagram/
Tx15 /Tx15规格参数Specs
VTX Setting/图传设置
/