SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 11086
INDEX
WINGSPAN: 1000mm
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of children’s reach!
Take enough safety precautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
For Advanced Flyers.
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
2
3~14
15
16
© 2001 KYOSHO
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
SPARE PARTS
OPERATING YOUR MODEL SAFELY
RADIO CONTROLLED .15 ENGINE POWERED
DUCTED FAN AIRCRAFT
Before commencing assembly, please read these instructions thoroughly!
1
4
A minimum 4 channel transmitter,
configured for aircraft.
Ensure you read and understand the instructions included with your radio.
Sharp Hobby Knife
Phillips Screwdriver (L, M, S)
Phillips Screwdriver (s)
Drill
Needle Nose Pliers
Awl
Scissors
File (round)
3 12
12 AA-size Batteries
AAAA
AAAA
AAAA
Wire Cutters
Required for engine starting:
Fuel Bottle
Plug Wrench
1 x Extension Lead
2
No.73801
Glow engine fuel only.
MOD
EL
ENGIN
E
FUEL
3
Epoxy A
Epoxy B
Instant Glue
(30 )
Epoxy Glue (30 minutes type)
Glue
CAUTION
:
For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION
:
Only use a minimum 4 channel transmitter, configured
for aircraft!
(No other radio may be used!)
WARNING: Normal gasoline
cannot be used
with glow engines.
Other equipment for enhancing airplane operation & performance
Fuel Filter
5
4
Others
Silicone Tube
Vibration Protection Sponge
x 4
A 4 Channel radio with 4 mini servos is required.
1
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
3
Symbols used throughout this instruction manual, comprise:
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased
separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Do not overlook this symbol!
low setting
Use an iron covered with a cloth!
Start at low setting. Increase the set--
ting if necessary. If it is too high, you
may damage the film.
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due to
variations of temperature. Smooth out as explained right.
Pay close attention here!
Warning!
One-touch Plug Heater Set
2
REQUIRED FOR OPERATION (Purchase separately!)
TOOLS REQUIRED (Purchase separately!)
BEFORE YOU BEGIN
3
1
3
2
Main Wing
Main Wing
Main Wing
Dihedral 32mm at wing tip.
Fill the gap with epoxy.
Do not disregard this symbol!
Warning!
Pay close attention here!
Apply epoxy glue.
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
Assemble left and right sides
the same way.
32mm
Install the hinges completely
before applying instant glue.
Align the centre of the main
wing with the aileron.
Note the direction.
Top
Securely glue together. If it comes off
during flights, you may lose control of
your airplane, resulting in an accident !
Warning!
2
Horn Chip
Horn Chip
Only cut the film.
Do not cut into the wood.
Only cut the film.
Do not cut into the wood.
Bottom Side
3.1
mm
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
32mm
4
4
6
5
Main Wing
Main Wing
Main Landing Gear
Do not disregard this symbol!
Warning!
Pay close attention here!
Apply epoxy glue.
Cut off shaded portion.
Assemble left and right sides
the same way.
Included with the
radio set.
Aileron Servo
5
mm
2
mm
If it comes off during flights, you may
lose control of your airplane, resulting
in an accident !
Warning!
8
TP Screw
2.6 x 8mm
2.6 x 8mm
2
2
3 x 4mm
Set Screw
2
Stopper
Collar
Collar
3 x 4mm
Stopper
Use the rest of wire in step .
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
ページを読み込んでいます...
6
Apply epoxy glue.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
11
10
Fuselage
Fuselage & Main wing
2
3 x 20mm
Screw
2
2
3mm
Washer
3mm
Blind Nut
3 x20mm
3mm
5
mm
Screw
Washer
3x 20mm
3mm
3mm
Blind Nut
4.5mm
12
3 x 14mm
TP Screw
TP
3 x 14mm
TP Screw
Enlarge holes with a file if it is needed.
4
The line is on the top.
Align it with the back
edge of the wing saddle.
4.5mm
70mm
6mm
Align with the
corner of engine
hatch.
Side view
These parts can not be reversed.
Cut the tip of pipe as illustrated to
allow smooth insertion.
7
Do not disregard this symbol!
Warning!
Pay close attention here!
Apply epoxy glue.
Cut off shaded portion.
Place PP pipe and aluminum
pipe in their correct positions
and glue trunk frame on the
fuselage.
Attach with epoxy all around
the perimeter.
Assemble in the specified order.
13
Back
Figures on the
picture are the
length of the PP
pipe coming out.
5
5
12
12
20
20
14
Cut PP pipe (thick) and aluminum
pipe as following length.
15
Engine
4
3 x 20mm
Cap screw
4
4
3mm
Washer
3mm
Spring Washer
4
3mm
Nylon Nut
3 x 20mm
3mm
Warning!
8
Pay close attention here!
Cut off shaded portion.
16
Engine
2.6 x 8mm
TP Screw
1
2.6 x 8mm
17
Engine Muffler
Position the muffler so that
the 3x5mm screw is 45 degrees
to the engine.
2.6 x 22mm
2.6 x 22mm
18
4
3 x 14mm
TP Screw
TP
1
3mm
Washer
3mm
Nylon Nut
3 x 15mm
1
1
1
Screw
Screw
3 x 15mm
3 x 14mm
5
mm
3mm
3mm
Drill a hole for engine slow speed
adjustment.
Use the rest of wire.
6
mm
10
mm
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
9
Do not disregard this symbol!
Warning!
Pay close attention here!
19
1
3 x 25mm
Cap Screw
1
7 mm
Washer
1
Drive Nut
Drive Nut
Note the direction.
20
1
Nose Landing Gear Horn
3
1
3 x 4mm
Set Screw
4
Stopper
Collar
Nose Gear Horn
3 x 4mm
Stopper
21
Fuel Tank
1
3 x 25mm TP
TP Screw
5mm
After confirming
the direc-tion (see
front view of fuel
tank), insert and
tighten the screw.
Bend as shown
here.
12mm
3 x 25mm
Completed
Ensure smooth non-binding
movement while assembling.
Apply epoxy glue.
3 x 25mm
7mm
Warning!
Tighten the nut securely.
If it comes off during flights,
you may lose control of your
airplane, resulting in an accident !
3 x 4mm
Stopper
Collar
3mm
10
Do not disregard this symbol!
Warning!
Pay close attention here!
Cut off shaded portion.
22
Cut the velcro in half before installing.
Velcro
23
To the carburetor
3 x 10mm
1
1
1
3mm
Nylon Nut
3mm
Washer
Horn chip
24
Horizontal Tail
Install the hinges completely
before applying instant glue.
2
mm
17
mm
3
mm
2
Apply epoxy glue.
Assemble left and right sides
the same way.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
Must be purchased separately!
7mm
10mm
View from the bottom
Horn Chip
Warning!
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
ページを読み込んでいます...
12
30
29
Rudder Servo
Rudder Linkage
Apply epoxy glue.
Included with the radio set.
3 x 4mm
Set Screw
1
2mm
Washer
Nut
Linkage Stopper
1
1
1
2mm
Must be purchased separately!
28
Rudder Linkage
3 x 30mm
1
2
2
3mm
Nut
3mm
Washer
( L )
Horn chip ( L )
2
2
mm
3.1mm
2mm
2mm
3 x 4mm
2 x 6
Crimp this part with a pliers.
Crimp this part with a pliers.
2 x 6
Assemble left and right sides
the same way.
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
13
31
32
Do not disregard this symbol!
Warning!
Pay close attention here!
Apply epoxy glue.
Cut off shaded portion.
2
mm
3 x 4mm
Set Screw
2
2mm
Washer
Nut
Linkage Stopper
2
2
2
2mm
Place Servos close.
Cut off shaded portion.
Included with the
radio set.
2mm
2mm
3 x 4mm
Cut off shaded portion.
Support block for elevator rod.
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
Front
33
Secure foam padding with
rubber bands or tape as required.
Foam Protection
Receiver
Receiver Power Supply
Receiver
Switch
Receiver Power Supply
Install carefuly the receiver and battery pack to
ensure that they will not move during flights.
Place as far forward
as possible.
Must be purchased separately!
Assemble in the specified order.
20mm
Warning!
Make sure to solder securely.
If not properly solderd, a faliure
in flight may occur.
14
34
35
Do not disregard this symbol!
Warning!
Pay close attention here!
Apply epoxy glue.
Cut off shaded portion.
2x6mm
2x6mm
2 x 6mm
TP Screw
TP
Decals
2
mm
2
mm
1
mm
RUDDER
ELEVATOR
AILERON
Adjust the travel of each control surface to the values in the
diagrams. These values fit general flight capabilities.
Readjust according to your needs and flight level.
5mm
5mm
If necessary, re-position receiver and battery to get correct
C of G.
Check C of G position before flying.
Ensure all screws are securely tightened before flight.
Warning!
Warning!
10mm
10mm
16mm
16mm
CG
185 mm
(from wing leading edge)
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
Pilot holes
This aircraft has been designed for intermediate to experienced level flyers. First time pilots should seek the advice of more experienced flyers during
construction and for initial flights. Initially, less experienced pilots should only fly with an experienced pilot, until they become more proficient. This
aircraft is designed to be powered by either a 2 stroke .15 size engine. Installation of engines other than those specified could to lead to a serious accident
and/or damage to property.
Position for
left diagram.
Position for
left diagram.
Position for
left diagram.
185 mm
C of G position Adjustment
15
36
Decals
For the correct placement of decals, please refer to the box top
and illustrations below.
No.
DF101
DF101-1
DF101-2
DF101-3
DF101-4
DF102
Ducted Fan Set
4500
1000
1500
1000
1200
1000
6500
Ducted Fan Case
Mount Set
Ducted Fan Blade
No. Part Names Quantity
11086-02
11086-03
200
200
1000
Part Names Quantity
1000
2000
Landing Gear Set
Fuel Tank
90050
Super Tuned Silencer
SPARE PARTS
x1
x1
x1
x1
x1
x1
x1 Set
x1 Set
x1
x1
11086-01
Canopy
FOR JAPANESE MARKET ONLY.
Decal
1701KP
250
Tie Strap (M) LF.Pink
Tie Strap (M) LF.Yellow
1701KY
250
92525
1000
Muffler Joint Pipe
96321
450
Push Choke Button
R
20mm
80mm
PRINTED IN JAPAN
© 2001 KYOSHO
OFF
ON
Before Flying
Before flying your airplane, ensure
the airfield is spacious enough.
Always fly it outdoors in safe areas
with no debris or obstacles!
For handling the radio properly,
refer to its instruction manual.
Ensure the spinner and propeller are
securely attached.
If your airplane begins to operate by
itself, there is another transmitter on
your frequency. Immediately stop
your airplane; otherwise you may
lose control of it which will result in
accidents.
Fully extend
the transmitter
antenna.
Switch on the transmitter.
Switch on the receiver.
Ensure the wings are securely
attached.
Flying
Fill the fuel tank.
By moving the control sticks, ensure
all control surfaces moves as per
your adjustments.
For starting the engine, apply low
throttle and hold the engine starter
against the spinner.
Adjust the needle.
After Flying
Only use KYOSHO genuine parts!
Cautions for Safety
Adjust the engine always from behind,
but never from infront or the sides as
a rotating propeller may badly injure
you!
Do not allow watching people to get
too close to a rotating propeller.
Immediately disuse defective pro-
pellers as well as deformed spinners.
If the dry batteries in the radio are
flat, replace them with fresh ones.
Do not fly your airplane above people
standing around.
ON
ON
Hand-launch your airplane into the
wind to make it take off.
Do not fly your airplane when there
is a strong wind or a lateral wind.
Always land your airplane into the
wind.
Bring your airplane to a halt by
lowering the throttle trim.
After each flight, the engine is very
hot. Beware of getting burned!
Wipe away any fuel deposits or dirt.
Never throw burning, gleaming or
smouldering things into fuel cans,
even if these happen to be empty.
This will result in serious injury!
WIND
WIND
OFF
OFF ON
Switch off the receiver.
Switch off the transmitter.
OFF
Draw out the remaining fuel from the
fuel tank and fill it back into the can.
By moving the throttle control
stick, ensure the carburetor opens
and closes without effort.
62150106-3 PRINTED IN CHINA
Always do observe the following in order to prevent accidents!
FLIGHT MANUAL
Warning!
/
