Kyosho 11808 ユーザーマニュアル

カテゴリー
おもちゃ
タイプ
ユーザーマニュアル

このマニュアルも適しています

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No.11808
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
OPTIONAL PARTS
OPERATING YOUR MODEL SAFELY
WINGSPAN: 1390mm
SAFETY PRECAUTIONS
This radio control model is not a toy!
For Intermediate
&
Advanced Flyers.
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
3
3~14
15
15~16
RADIO CONTROLLED ENGINE POWERED SCALE AIRCRAFT
KYOSHO SUPER QUALITY WARBIRDS SERIES
Before commencing assembly, please read these instructions thoroughly.
P-51D MUSTANG 40
© 2000 KYOSHO
40
INDEX
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of children s reach!
Take care before operating this model.
You are responsible for this model s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
Sharp Hobby Knife
Phillips Screwdriver (L, M, S)
Needle Nose Pliers
Awl
Scissors
Wire Cutters
2
REQUIRED FOR OPERATION (Purchase separately!)
TOOLS REQUIRED (Purchase separately!)
1
A minimum 4 channel radio control
system for aircraft
3 12
12 AA-size batteries,
either dry cell or NiCd.
Read instruction manual supplied with radio control system thoroughly before use.
5
For retract gear, you will need 5channel radio, 1 retract servo,
1 extension cord.
AAAA
AAAA
AAAA
2
Model Aircraft Engine
Muffler
Muffler Adapter
Engine and Muffler
Glow Plug
3
2
Extension Lead x 2
(200mm)
1
Y- Harness x 1
Purchase a propeller that
will suit your engine.
Propeller
CAUTION
: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION
: Only use radio control systems designed for 
aircraft.
2 40 ~ 46
4 48 ~ 53
2 Stroke .40 ~ .46
4 Stroke .48 ~ .53
Propeller
4
Fuel Tube
Shock Protecting Foam
x5
This model will require a minimum 4 channel radio control
(with 5 standard servos) for aircraft, if having fixed
undercarriage, or 5 channel radio (with 6 standard servos),
if fitting retractable undercarriage.
One-touch Plug Heater Set
Required for engine starting:
Fuel Bottle
Plug Wrench
5
Model Glow Fuel.
MO
DEL
EN
G
INE
FUEL
6
SILICONE
Epoxy A
Epoxy B
Instant Glue
(30 )
Epoxy Glue (30 minute type)
Silicone Glue
Glue
WARNING: Never use petrol/
gasoline with glow
engines.
Engine Starter
12V
12V Battery (for starter)
Other equipment for enhancing aircraft operation & performance
For retracting landing gear.
Fuel Filter
Retracting landing gear
Rod and screw
7
8
3
1
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
5
Symbols used throughout this instruction manual comprise the following:
Main Wing
1
Apply epoxy glue.
Assemble left and right
sides the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Do not overlook this
symbol!
Pay close attention here!
Warning!
Secure aileron hinges with instant glue,
being careful not to glue the wing and
aileron together.
Main Wing
2
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Cut away the film along the edges.
Feel for the edges of the holes
underneath of the film.
Cut away the film along the edges
Align the center line of
main wing with aileron.
Use a hair drier to spread out wrinkle on the film.
But,be careful of the temperature. High temperature may damage the film.
3
Pay attention not to spill fuel on the film. It may fade color of the film.
4
2 x 6mm
3mm
2 x 22mm
2 x 22mm
Screw
4
2 x 6mm
Screw
Adjust the travel of each control surface.
Please refer to .
22
22
2mm
Warning!
2
3mm
Set Screw
4
90
2 x 6mm
2 x 6mm
4
Main Wing
4
Main Wing
3
Included with the radio set.
2 x 6mm TP
TP Screw
8
Make certain parts are aligned accurately and
play is reduced to a minimum.
Tighten screws securely
Do not disregard this symbol!
Warning!
1mm
Assemble left and right sides
the same way.
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Aileron Servo
Ensure that the two wing halves are securely
glued together.
Warning!
P.13 24 P.14 29
Note, P13 24 P.14 29 , if you are using retracting landing gear.
P.13 24 P.14 29
Note, P13 26 P.14 31 , if you are using retracting landing gear.
P.13 26 P.14 31
4
Stopper (L)
3mm
Set Screw
8
4
3 x 10mm TP
TP Screw
Main Wing
Main Wing
6
7
Cut away covering film only.
Cut away covering film only.
3 x 10mm
Feel for the edges of the holes
underneath of the film.
Cut away the film along the edges
2mm
Note, P13 24 P.14 29 , if you are using retracting landing gear.
5
Apply epoxy glue.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Main Wing
5
A = AÕ
Main Wing
Cut away only covering film.
9
8
Engine Mount
Align lower face of engine
mount arm on "Crankshaft
Center line".
4 x 20mm
Cap Screw
4
4
4x20mm
4mm
A
A
2
A
2
Crankshaft Center Line
5mm
4mm
Blind Nut
4 x 35mm
Cap Screw
2
4mm
Washer
2
4mm
Blind Nut
4.1mm
Align with main wing holes.
A
Cut away only covering film.
Apply instant glue
(CA glue, super glue).
2
6
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
113mm
3.1mm
7
11
Fuel tank
3x18mm
5mm
After confirming the position
(see front view of fuel tank),
insert and tighten the screw.
Fix with silicone glue.
3 x 18mm
Screw
1
10
Engine Mount
Throttle Rod
4
3 x 30mm
Screw
4
3mm
Washer
4
3mm
Nut
4mm
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Engine Mount
Washer
3mm
3 x 30 mm
Nut
3mm
Engine
Depends on the position
of the throttle arm.
C
A
B
L
3mm
Cut away only covering film.
mm
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
A = AÕ B = BÕ
C = CÕ
Warning!
Make certain parts are aligned accurately
and play is reduced to a minimum
Ensure that the horizontal
stabiliser is securely glued
to the fuselage.
12
Cowling
2 x 10mm
Horizontal / Vertical Tail
13
Secure elevator hinges with instant glue,
being careful not to glue the elevator
to the horizontal stabiliser.
Relieve the cowl to
clear the engine head.
2 x 10mm TP
TP Screw
4
3 x 16mm TP
TP Screw
2
3 x 16mm
3mm
1mm
8
Apply epoxy glue.
Cut off shaded portion.
Pay close attention here!
Do not disregard this symbol!
Warning!
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
X
2
2
Assemble as many times as
specified (here:twice).
Assemble left and right sides
the same way.
L
X
2
1
Stopper (S)
3mm
Set Screw
2
1
2 x 10mm TP
TP Screw
100mm
Warning!
To servo .
To elevator horn.
15
Rudder / Elevator Rod
To servo.
To rudder horn.
2mm
2mm
Heat-shrink Tube
Beware of the flame!
Slide heat shrink tubes over linkage rods and use
a hair drier or similar to secure (shrink) them in place.
Be careful not to scorch the
heat-shrink tube!
Bend at end of rod.
14
Rudder / Elevator Rod
450mm
450mm
To rudder horn.
To elevator horn.
Secure rudder hinges with instant glue,
being careful not to glue the rudder
to the vertical fin.
Stopper (S)
3mm
2 x 10mm
1mm
100mm
2mm
9
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Vertical Fin
Pay close attention here!
16
Apply instant glue
(CA glue, super glue).
Do not disregard this symbol!
Warning!
3mm
2mm
3mm
2mm
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
125mm
47mm
Elevator Rod
Rudder horn
2 x 6mm
3mm
Elevator horn
3mm
2 x 6mm
120mm
30mm
Rudder Rod
2 x 14mm
Cut off excess.
Cut off excess.
2mm
2mm
2 x 14mm
Vertical Fin
17
2 x 14mm
Screw
2
2 x 6mm
Screw
1
3mm
Set Screw
2
Horizontal Tail /Stabiliser
18
2 x 14mm
Screw
2
2 x 6mm
Screw
1
3mm
Set Screw
2
Cut off excess.
Paint the canopy frame in silver.
1mm
2 x 6mm TP
TP Screw
2 x 6mm
3
11
Must be purchased separately!
2mm
pecified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Radio Equipment
19
Pay close attention here!
3mm
Set Screw
1
2mm
Washer
1
(B)
Linkage Stopper (B)
1
2mm E
E ring
1
Canopy
20
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
3mm
2mm
E
E ring
Throttle Servo
Elevator Servo
Rudder Servo
Battery / Receiver
CG
2mm
120mm
130mm
Pilot
Position for rudder diagram
Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according
to your requirements and flight experience.
Note the direction.
Left Right
12 mm
12 mm
25 mm
10 mm
10 mm
RUDDER
ELEVATOR
AILERON
25 mm
Position for elevetor diagram
Apply included decals to nose cowl side.
For the correct location of decals, please refer to the box top.
Position for aileron diagram
1mm
12
Assemble left and right sides
the same way.
Apply instnt glue(CA glue,
super glue).
22
Decals
23
Pay close attention here!
Main gear
21
8
2 x 10mm TP
TP Screw
2 x 10mm
Apply epoxy glue.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Retractable Gear
Included with the radio set.
Retract Servo
Included with the radio set.
Retractable Gear
Retractable Gear
Retractable Gear
13
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased separately!
Cut off shaded portion.
24
25
26
82mm
170mm
A retractable landing gear system is not included in this kit and must be purchased separately.
To install retractable undercarriage, a minimum 5 channel radio with 1 additional retractable
gear servo and 1 extension cord is required.
View from Underside of Main Wing
Cut out the outline of wheel well to
a diameter of 82mm. Cut out the wheel
well inserts shown in Section 7 first,
and use them as a guide when cutting
wheel well recesses to ensure that you
do not cut holes oversize.
29
View from Top Side of Main Wing
Cut off excess.
Bend wire for smooth operation.
Make sure linkages for landing gear are properly locked.
If linkage rods foul, bend accordingly to ensure
free movement.
14
Assemble left and right sides
the same way.
Cut off shaded portion.
Pay close attention here!
27
28
29
Apply instant glue
(CA glue, super glue).
Retractable Gear
Retractable Gear
Retractable Gear
Remove shaded area.
View from Underside of Main Wing
Nylon Propeller
PP
P.P. Pipe
300
Fuel Tube Stopper
Polipropylene Pipe
200
90469
91490
90410-06
D10 x P6 Nylon Propeller
Nylon Propeller
Nylon Propeller
Nylon Propeller
Nylon Propeller
Nylon Propeller
D11 x P7
550
650
D10 x P8
D10 x P7
550
550
D11 x P8 650
90411-07
90410-08
90410-07
90411-08
D12 x P6 750
750
3800
2000
90412-06
D12 x P8
90412-08
90080
90903
OS52 (UNF 1/4 - 28)
Adopter nut. For OS.52
350
YS53 (M6)
Adopter nut. For YS.53
350
90487-05
90487-06
15
PARTS
No. Part Names Quantity No. Part Names
:FOR JAPANESE MARKET ONLY.
Quantity
:FOR JAPANESE MARKET ONLY.
OPTIONAL PARTS
No. Part NamesNo. Part Names
2 ~46 4 ~53
 This model aircraft is designed for Intermediate to Experienced fliers. Beginners should seek advice for pre-flight adjustments
and assembly from more experienced fliers. Be aware that flying a badly assembled or badly adjusted aircraft is very
dangerous!
 At the start, first-time fliers should always be assisted by an experienced flier and NEVER fly alone!
 This model aircraft is designed to be powered by either a 2 stroke .40 ~ .46 size engine or a 4 stroke .48 ~ .53 size engine. 
 Installing a more powerful engine than specified or flying this model dangerously could lead to serious injury and/or damage
to property.
Do not overlook this symbol!
Warning!
Warning!
11808-01
11808-02
11808-03
90424-70
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market
11808
OFF
ON
Pre-Flight Checks
Only fly model aeroplanes in areas
away from houses and places
where people gather. The weight
and speed of your aeroplane make
it a potential hazard. Make sure
that the area around you is clear.
For radio equipment, refer to the
instruction manual included with
your set.
Check that the spinner and the
propeller are securely fastened.
If the model begins to operate by
itself, there is another transmitter
operating on your frequency. Do
not try to operate your model if
this happens, but change your
transmitter and receiver crystals
to another frequency.
Fully extend
transmitter
aerial.
Switch on the transmitter.
Switch on the receiver.
Check that the wings are properly
and firmly affixed.
Flying
Fill the fuel tank.
By moving the various transmitter
controls, ensure that all control
surfaces move the way you
intend them to.
To start the engine, set low throttle
on the transmitter and hold the
engine starter against the spinner.
Switch on engine starter.
Adjust the throttle needle.
After Flying
Only use genuine KYOSHO parts.
Safety Precautions
Always adjust the engine from
behind, and never from in front or
from the side. A rotating propeller
could badly injure you.
Do not allow spectators to get too
close to the model, especially a
rotating propeller.
Immediately replace defective
propellers and spinners.
Always ensure that your
transmitter and receiver batteries
are fully charged.
For best results,
use rechargeble
Nicd cells.
Do not fly your aeroplane too close
to spectators.
ON
ON
Launch the aeroplane into the wind.
Do not fly your aeroplane if it is a
windy day or there are strong
cross winds.
Always land the aeroplane into the
wind.
Bring the aeroplane to a halt by
lowering the engine control trim.
After each flight, the engine will be
very hot. Be careful to avoid
accidentally burning yourself.
Wipe up any fuel deposits or dirt.
Never dispose of fuel or fuel cans
in fires, as this could cause serious
injury.
WIND
WIND
OFF
OFF ON
Switch off the receiver.
Switch off the transmitter.
OFF
Draw remaining fuel from the tank
and dispose of it responsibly.
Move the throttle control stick
on the transmitter and check
that the carburettor opens and
closes easily.
R
THE FINEST RADIO CONTROL MODELS
PRINTED IN CHINA85290007-1
Non-observance of this information could lead to serious injury and/or damage to property.
Warning!
FLIGHT MANUAL
243-0034 153
TEL.046-229-4115
( ) 10:00~18:00
1 / 1

Kyosho 11808 ユーザーマニュアル

カテゴリー
おもちゃ
タイプ
ユーザーマニュアル
このマニュアルも適しています

他の言語で