*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 11905
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
SPARE PARTS
OPERATING YOUR MODEL SAFELY
INDEX
WINGSPAN: 1475mm
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of childrenÕs reach!
Take enough safety precautions prior to operating this model.
You are responsible for this modelÕs assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
For Intermediate
&
Advanced Flyers.
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
GILES G-202 60
2
3
3~13
13
16
RADIO CONTROLLED ENGINE POWERED
ALL-BALSA ACROBATIC AIRCRAFT
Before commencing assembly, please read these instructions thoroughly!
© 2000 KYOSHO
1
A minimum 4 channel radio control
system for aircraft.
12
12 AA-size Batteries,
either dry cell or NiCd.
Read instruction manual supplied with radio control system
thoroughly before use.
Hobby Knife Phillips Screwdriver (L, M, S)
Needle Nose Pliers
Awl
Scissors
AAAA
AAAA
AAAA
2
Model Aircraft Engine
Muffler
Muffler Adapter
Engine and Muffler
Glow Plug
Wire Cutters
3
Required for engine starting:
Fuel Bottle
Plug Wrench
xtension Lead x 2
Y- Harness x 1
5
Model Glow Fuel.
M
ODEL
ENGINE
FUEL
6
SILICON
Epoxy A
Epoxy B
Instant Glue
Epoxy Glue (30 minutes type)
Silicon Glue
Glue
Purchase a propeller that
will match your engine.
Propeller and Spinner
CAUTION
: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION
: Only use radio control systems designed for aircraft.
WARNING: Never use petrol /
gasoline with glow
engines.
2 46 ~ 60
4 70 ~ 90
2 Stroke .46 ~ .60
4 Stroke .70 ~ .90
Engine Starter
12V Battery (for starter)
Other equipment for enhancing airplane operation & performance
Fuel Filter
8
62mm
Spinner 62mm
Propeller
4
Fuel TubeShock Protecting Foam
5 x5
This model will require a minimum 4 channel radio
control (with 5 standard servos) for aircraft.
Linkage Parts
7
Please use stronge control horns and pushlods
intended for large sized models.
One-touch Plug Heater Set
2
REQUIRED FOR OPERATION (Purchase separately!)
TOOLS REQUIRED (Purchase separately!)
1
Read through the manual before you begin, so you will have an overall idea of what to do.
BEFORE YOU BEGIN
ASSEMBLY
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
3
Symbols used throughout this instruction manual, comprise the following:
Apply epoxy glue.
Assemble left and right
sides the same way.
Must be purchased
separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Ensure smooth non-binding
movement while assembling.
Do not overlook this
symbol!
low setting
Use an iron covered with a cloth!
Start at low setting. Increase the set--
ting if necessary. If it is too high, you
may damage the film.
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due to
variations of temperature. Smooth out as explained right.
Pay close attention here!
Warning!
Main Wing
1
Align the center line of main
wing with aileron.
3
Cut off shaded portion.
Apply epoxy glue. Apply instant glue (CA glue, super glue).
Hole for servo connector.
Before cutting away the covering film,
lightly heat that area with an iron.
Assemble left and right sides
the same way.
Secure aileron hinges with instant
glue, being careful not to glue the
wing and aileron together.
4
Warning!
Note the direction.
Top
Top
If there is a gap, carefully fill
with epoxy glue.
Securely glue together. If coming off during flights, you lose
control of your airplane which leads to accidents!
40mm
Main wing underside
Main Wing
2
Hole for servo connector. Before cutting away the covering
film, lightly heat that area with an iron.
Cut away film only.
Glass Fiber Tape
Main wing underside
Apply epoxy glue.
4
Assemble left and right sides
the same way.
Main Wing
Cut off shaded portion.
Pay close attention here!
Main Wing
3
Main Wing
5
Adjust the travel of each control surface.
Please refer to section .
21
21
Align with main wing holes.
Cut away film only.
Aileron servo
extension cord
Included with the radio set.
Front
Front
Aileron servo
Tape
Cut the mount to fit
your servo.
4
Main Wing
4
mm
5
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
Main Wing
6
3 x 10mm
6 x 35mm
2 x 10mm
6mm
3mm
L
Stopper (L)
8
Engine Mount
4 x 25mm
133mm
4mm
4mm
4.2
mm
4 x 25mm
Cap Screw
4
4mm
Nut
4
4mm
Washer
4
Mark.
Note the direction.
Mark
Mark
Mark
Left
Left
Right
Right
6mm
1mm
6
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Pay close attention here!
Main Landing Gear
7
2mm
6x 35mm
Screw
2
6mm
Nut
2
4
3 x 10mm TP
Screw
2
2 x 10mm TP
Screw
Attach gearpant and wheel to leg using
parts provided making certain wheel rotates
freely.
2
Stopper (L)
3mm
Set Screw
2
Ensure smooth non-binding
movement while assembling.
9
Engine Mount
4
4mm
Mount Nut
4mm
Mount Nut
4 x 20mm
Cap Screw
4
Align the crankshaft of the
engine with the side line.
Be sure the muffler will fit before
mounting the engine.
Use a muffler extension adapter.
(Purchase separately)
Be sure the muffler will fit before
mounting the engine.
Align the mark on both mounts
with the mark on the fuselage.
Align the crankshaft of the
engine with the side line.
Align the mark on both mounts
with the mark on the fuselage.
In case of 4stroke engine.
In case of 2stroke engine.
Mark
Side Line
Side Line
4mm
Mount Nut
4 x 20mm
4 x 20mm
10
Fuel Tank
Tail Pipe
Throttle Rod
Tail Pipe
Silicone Tube
5mm
5mm
Mark
Drill the hole for Throttle Rod.
Drill the hole for Throttle Rod.
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Pay close attention here!
7
2mm
1mm
2 x 10mm
3~4mm
12
Main Wing Undercover
Warning!
Securely attach the Main Wing. If the wing separates
during flight, you will lose control of your airplane.
A
A = AÕ
AÕ
4 x 30mm
Cap Screw
2
4mm
Washer
2
4 x 30mm
4x30mm
Make certain the plane is aligned accurately per the diagram.
A mis-aligned plane can fly erratically and cause accidents.
Cut away only the film.
Cut away film only.
Cut away only the film.
4mm
2
4mm
Mount Nut
4mm
Mount Nut
Apply instant glue (CA glue, super glue).
Apply epoxy glue.
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Relieve the cowl to clear the engine
head.
8
Cowling
11
2 x 10mm TP
TP Screw
5
Vertical / Horizontal Tail
13
A
AÕ
BÕB
D
C
DÕ
CÕ
Warning!
Securely glue together. If the wing separates during flight,
you will lose control of your airplane.
Feel for the edges of the holes underneath the film.
Then, cut away the film along the edges.
Cut away film only.
Vertical / Horizontal Tail
14
3mm
Set Screw
1
2
2 x 10mm TP
Screw
Stopper (S)
1
Warning!
2 x 10mm
Securely glue together. If the wing separates during flight,
you will lose control of your airplane.
3mm
2mm
A = AÕ B = BÕ
C = CÕ D = DÕ
Cut away film only.
Stopper (S)
9
Apply epoxy glue.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
Ensure smooth non-binding
movement while assembling.
10
Assemble left and right sides
the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
17
16
Throttle Rod
Canopy
You can also attach the canopy without
screws, using silicon glue.
2 x 6mm TP
TP Screw
6
15
Apply instant glue (CA glue, super glue).
10mm
2mm
Silver Decal
Cut off
Vertical / Horizontal Tail
2 x 6mm
Apply instant glue into the screw hole as a reinforcement.
2mm
Ensure smooth non-binding
movement while assembling.
1mm
Throttle Servo
Throttle Rod
Included with the radio set.
Apply instant glue (CA glue, super glue).
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Pay close attention here!
2mm
11
Elevator Rod
19
20
18
Rudder Rod
Bottom View
Linkage
Rudder Servo
Elevator Servo
Elevator Rod
Rudder Rod
Rudder Rod
Throttle Servo
Rudder Servo
Elevator Servo
Elevator Rod
Run the throttle linkage to suit your engine. Make
certain the linkage is strong and secure. Reduce
play to a minimum for best perfpormance.
Run the throttle linkage to suit your engine. Make
certain the linkage is strong and secure. Reduce
play to a minimum for best perfpormance.
Apply epoxy glue.
Must be purchased separately!
Pay close attention here!
12
22
21
View From Underside
Linkage
Radio Equipment
Secure foam padding with rubber bands or tape as required.
Carefully install the receiver and battery pack to ensure
that they will not move during flight.
Position for
right diagram.
Never fly before checking the CGÕs required position.
Move the location of the receiver and battery pack as
needed to obtain the specified CG.
Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities.
Cut away the hole for pushrods.
Elevator Pushrod
Rudder Pushrod
Elevator Pushrod
Rudder Pushrod
Shock Protecting Foam
23
CG
12mm
12mm
RUDDER
ELEVATOR
AILERON
35mm
35mm
UP 15mm
DOWN 15mm
85 100mm
Position for
right diagram.
Position for right diagram.
Adjust the travel of each control
surface.
Please refer to section .
23
23
24
Decal
13
2 46~60 4 70 90
This model aircraft is designed for Intermediate to Experienced fliers. Beginners should seek advice for pre-flight adjustments
and assembly from more experienced fliers. Be aware that flying a badly assembled or badly adjusted aircraft is very
dangerous!
At the start, first-time fliers should always be assisted by an experienced flier and NEVER fly alone!
This model aircraft is designed to be powered by either a 2 stroke .46 ~ .60 size engine or a 4 stroke .70 ~ .90 size engine.
Installing a more powerful engine than specified or flying this model dangerously could lead to serious injury and/or damage
to property.
This model is desingned for sports stant. This model is not suited for modification such as
retractable wheel or tuned silencer.
Do not overlook this symbol!
Warning!
The box art and below picture can be used for the placement
of the decals. (Some decals are not included.)
PARTS
No. Part Names Quantity
11905-01
Cowling
Wheel Cover
1
1
4500
1500
11905-04
Main Gear
11905-03
(L.R) 1 3000
No. Part Names
:FOR JAPANESE MARKET ONLY.
Quantity
11905-02
Canopy
1
11905-05
Decal for G202
2000
1
1500
ALL-BALSA AEROBATIC AIRCRAFT
ALL-BALSA AEROBATIC AIRCRAFT
R
THE FINEST RADIO CONTROL MODELS
R
THE FINEST RADIO CONTROL MODELS
R
THE FINEST RADIO CONTROL MODELS
R
THE FINEST RADIO CONTROL MODELS
R
THE FINEST RADIO CONTROL MODELS
R
R
R
THE FINEST RADIO CONTROL MODELS
R
THE FINEST RADIO CONTROL MODELS
RESCUE
RESCUE
RESCUE
RESCUE
No.11950 GILES G202-60 PRINTED IN CHINA
CAUTION
ENGINE HEAD
CAUTION
ENGINE HEAD
Warning!
200
200
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market
11905
GILES G-202 60
The servise mentioned below is available only for Japanese market.
OFF
ON
Pre-Flight Checks
Only fly model aeroplanes in areas
away from houses and places
where people gather. The weight
and speed of your aeroplane make
it a potential hazard. Make sure
that the area around you is clear.
For radio equipment, refer to the
instruction manual included with
your set.
Check that the spinner and the
propeller are securely fastened.
If the model begins to operate by
itself, there is another transmitter
operating on your frequency. Do
not try to operate your model if
this happens, but change your
transmitter and receiver crystals
to another frequency.
Fully extend
transmitter
aerial.
Switch on the transmitter.
Switch on the receiver.
Check that the wings are properly
and firmly affixed.
Flying
Fill the fuel tank.
By moving the various transmitter
controls, ensure that all control
surfaces move the way you
intend them to.
To start the engine, set low throttle
on the transmitter and hold the
engine starter against the spinner.
Switch on engine starter.
Adjust the throttle needle.
After Flying
Only use KYOSHO genuine parts.
Safety Precautions
Always regulate the engine from behind,
but never from infront or from the sides,
because a rotating propeller might badly
injure you.
Do not allow watching people to get too
close to a rotating propeller.
Immediately disuse defective propellers
as well as deformed spinners.
If the batteries of the radio system
are flat, replace them with new ones.
Do not fly your airplane above people
standing around.
ON
ON
Launch the aeroplane into the wind.
Do not fly your aeroplane if it is a
windy day or there are strong
cross winds.
Always land your airplane into the
wind.
Bring your airplane to a halt by
lowering the engine control trim.
After each flight, the engine is hot. Be-
ware of getting burned.
Wipe up any fuel deposits or dirt.
Never throw burning, gleaming or smoul-
dering things into fuel cans, even if
these happen to be empty. This could
result in serious injury.
WIND
WIND
OFF
OFF ON
Switch off the receiver.
Switch off the transmitter.
OFF
Draw the remaining fuel out of the tank
and fill it back into the can.
Move the throttle control stick
on the transmitter and check
that the carburettor opens and
closes easily.
R
THE FINEST RADIO CONTROL MODELS
PRINTED IN CHINA
85290005-1
Non-observance of this information could lead to serious injury and/or damage to property.
Warning!
FLIGHT MANUAL
243-0034 153
TEL.046-229-4115
( ) 10:00~18:00
/