11852-T01
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
EXPLODED VIEW
OPERATING YOUR MODEL SAFETY
PARTS LIST
FLIGHT MANUAL
WINGSPAN: 1360mm (53.54")
This radio control model is not a toy!
For Advanced Flyers
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
3
3 ~ 18
19
20
21
24
1:6 Scale Radio Controlled Super Quality Series .50 Engine Powered Airplane
No.11852 / No.11852YS
Before Begining assembly, please read these instructions thoroughly.
© 2005 KYOSHO CORPORATION
INDEX
UNDER SAFETY PRECAUTIONS
First-time builders should seek the advice of experienced
modellers before beginning assembly and if they do not fully
understand any part of the construction.
Assemble this kit only in places out of childrenÕs reach!
Take enough safety precautions prior to operating this model.
You are responsible for this modelÕs assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
OXALYS 50
1
For handling the radio properly, refer to its instruction manual.
Sharp Hobby Knife
Phillips Screwdriver (L, M, S)
Drill, Handgrinder
Needle Nose Pliers
Awl
File
Wrench
Scissors
2
Model Airplane Engine
Muffler
Engine, Glow Plug and Muffler
2-stroke .46~.50
4-stroke .52~.63
Glow Plug
Wire Cutters
3
Required for engine starting:
Fuel Pump
Plug Wrench
2
2 aileron extension cords
5
Glow engine fuel only.
MODE
L
ENGINE
FUEL
6
SILICON
Epoxy A
Epoxy B
Instant Glue
30
Epoxy Glue (30 minutes type)
Silicon Glue
Glue
Purchase a propeller that
will match your engine.
Propeller and Spinner
CAUTION: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION: Only use a minimum 4 channel radio for aircraft!
(No other radio may be used!)
WARNING: Normal gasoline
cannot be used with
glow engines.
.46 .50
4 .52 63
Engine Starter
12V
12V Battery (for starter)
Other equipment for enhancing
airplane operation & performance
Fuel Filter
Polyurethane paint (Clear)
Spinner(62mm
7
Propeller
4
Fuel line PP PipeSponge Sheet
4
5 x 5
A minimum 4 channel radio for airplanes (with 5
standard servos), and nicad or alkaline batteries are
required.
One-touch Plug Heater Set
REQUIRED FOR OPERATION (Not included in kit!)
TOOLS REQUIRED (Purchase separately!)
A B
2
1
2
3
BEFORE YOU BEGIN
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
Symbols used throughout this instruction manual, comprise:
Read through the manual before you begin, so you will have an overall idea of what to do.
Warning!
Main Wing
3
1
Main Wing
Make certain the hinges are adequately secured with glue.
If they come loose in flight accidents may result.
Aileron
Note the direction.
Secure nylon hinges with instant
glue, being careful not to glue the
wing and aileron together.
Align the center line of main wing
with aileron.
x2
3mm
Apply epoxy glue.
Assemble as many
times as specified.
Assemble in the
specified order.
Pay close attention here!
Assemble left and right
sides the same way.
Drill holes with the
specified diameter.
Apply instant glue
(CA glue, super glue).
Must be purchased
separately!
Cut off shaded portion.
Warning!
Do not overlook
this symbol!
Ensure smooth, non-binding
movement when assembling.
< >Top view.
You can keep the covering film from wrinkling or peeling by spraying the plane with clear polyurethane.
low setting
Use an iron covered with a cloth!
Start at low setting. Increase the set--
ting if necessary. If it is too high, you
may damage the film.
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due to
variations of temperature. Smooth out as explained
at right.
3mm
< >
4
Do not overlook this symbol!
Warning!
Apply epoxy glue.Drill holes with the
specified diameter.
3.2
mm
Cut off shaded portion.
3
Main Wing
Cut away film only, here.
Mark a line down the center.
Cut away film only, here.
Cut away film only, here.
Cut away covering film
only in these locations.
< >Top view.
Top
Front
2
Main Wing
Warning!
Pull out strings.
Ensure that the two wing halves are
securely glued together with epoxy.
Cut away covering film
only in these locations.
Pull out strings.
Use epoxy glue
to fill the opening.
Dihedral.
Stretch string across.
2.5mm
Pay close attention here!
12mm
4mm
3.2
mm
Note the direction.
< >Bottom view.
< >Top view.< >Bottom view.
Cut away film
only, here.
Align to top of main wing,
and make two holes.
3.2mm
< >
< >
< >< >
5
Must be purchased separately!
Do not overlook this symbol!
Warning!
Assemble left and right
sides the same way.
Cut off shaded portion.
5
Aileron Rod
Aileron Rod
Supplied with
the servo.
x2
x2
Bend.
Mark the spot to attach.
Neutral
x2
Assemble as many times
as specified.
4
Main Wing
Aileron Servo
Pull out servo cord with string.
Tie the string.
Servo extension cords
< >Bottom view.
Aileron Servo
Supplied with the servo.
Supplied with the servo.
Servo extension cords
1.5
mm
2mm
1.5
mm
1
1
Tie the string.
4
4
Warning!
Set all screws securely. If they come
off during flight you will lose control
of your aircraft!
2
5
6
4
7
1
2
3
2
3
2x20mm
4
2 x 20mm
Screw
Drill holes with the
specified diameter.
1.5
mm
Assemble in the specified order.
approx. 16mm
2mm
< >
16mm
1.5mm
6
Apply epoxy glue.
Cut off shaded portion.
7
Main Wing
Cut away film only, here.
Cut away film only, here.
6
Main Wing
< >Bottom view.
A = AÕ
2
3 x 30mm
Cap Screw
3mm
Washer
3mm
3mm
3x30mm
Pay close attention here!
A AÕ
2
Must be purchased separately!
Sillicone tube
< >
7
Assemble left and right
sides the same way.
Drill holes with the
specified diameter.
4mm
Cut off shaded portion.
9
Main Landing Gear
8
Main Landing Gear
Fix tank in fuselage with silicon glue.
4
3mm
Spring Washer
4mm
Spring Washer
4
3 x 12mm
Screw
6
4mm
Nut
Nut
Nut
4
4mm
Washer
Washer
2
4 x 35mm
Screw
Cut away film
only, here.
Cut away film
only, here.
4mm
4mm
4mm
4mm
4mm
4mm
4mm
4mm
3mm
3mm
3x12mm
4x35mm
4x35mm
4mm
7mm
Front
Ensure smooth, non-binding
movement when assembling.
< >For Left
< >For Left
< >For Right
< >For Right
Note the direction.
2
4mm
Spring Washer
Spring Washer
4mm
< >
< >
< >
< >
8
Do not overlook this symbol!
Warning!
Assemble left and right
sides the same way.
Cut off shaded portion.
10
Vertical
/
Horizontal Tail
Cut away film
only, here.
Cut away film
only, here.
Warning!
Warning!
Make certain plane is aligned accurately per the diagram.
A mis-aligned plane can fly erraticaliy and cause accidents.
Make certain plane is aligned accurately
per the diagram. A mis-aligned plane
can fly erraticaliy and cause accidents.
A = AÕ B = BÕ
C = CÕ
Secure nylon hinges with instant
glue, being careful not to glue the
wing and aileron together.
Align the center line of vertical
with rudder.
Note the direction.
Secure nylon hinges with instant
glue, being careful not to glue the
wing and aileron together.
Align the center line of horizontal
tall with elevator.
Note the direction.
Cut away film
only, here.
Pay close attention here!
Apply instant glue (CA glue, super glue).
Ensure smooth, non-binding
movement when assembling.
C
A AÕ
B BÕ
CÕ
9
Do not overlook this symbol!
Warning!
Drill holes with the
specified diameter.
5mm
12
Engine Mount
Align holes on the engine
mount and make marks
for each of the four holes.
Engine shaft line
To allow side thrust, the engine's shaft line is not positioned
down the center of the bulkhead.
Make marks according to
dimensions of engine used.
Apply epoxy glue. Cut off shaded portion.
11
Tail Gear
Cut away film only, here.
Warning!
Securely glue together. If coming
off during flights, you may lose
control and lead to accidents.
40mm
2x8mm
2x5mm
3x3mm
2
2 x 8mm
TP Screw
2
2
3
4
1
4
3
1
4
5
6
3mm
Assemble in the specified order.
A
2
A
2
A
1mm
4-stroke engine without
pump.
4-stroke engine with
pump.
2-stroke engine
Pay close attention here!
Mark
Align the Mark on the
engine mount to the
lateral line on the bulkhead.
1
3 x 3mm
Set Screw
1
2 x 5mm
Screw
A A
Engine mount position
5mm 5mm
5mm
TP
10
13
Engine Mount
14
Fuel Tank
Fix with silicone glue.
2.6x18mm
5mm
After confirming the posi-tion of the fuel tank's internal
parts(see front view), insert and tighten the screw.
Sillicone tube
Use a rod to align and install the
Mount Nut as per the illustration.
Hold Mount Nut with finger, and
temporarily insert washer & screw.
After inserting, remove screw
and washer.
Fuel Tank
Fuel Tank
1
2.6 x 18mm
Screw
For 4-
stroke
engine without pump. For 2-
stroke
engine.
Fuel Tank
For 4-
stroke
engine without pump. Page 10
14
For 4-
stroke
engine with pump. Page 11
15
For 2-
stroke
engine. Page 10
14
4
4mm
Mount Nut
Mount Nut
4
4 x 20mm
Screw
2
4mm
Washer
Apply epoxy glue between Firewall and Bulkhead
from inside of fuselage.
4x20mm
4x20mm
4mm
4x20mm
3
4
2
1
Assemble in the specified order.
x4
x4
Assemble as many times
as specified.
10
14
11
15
10
14
11
Drill holes with the specified
diameter.
3.2
mm
Apply epoxy glue.
Silicone Glue
Fuel Tank
15
Fuel Tank
Fuel Tank
2.6x18mm
5mm
After confirming the posi-tion of the fuel tank's internal
parts(see front view), insert and tighten the screw.
Sillicone tube
1
2.6 x 18mm
Screw
Front
For 4-
stroke
engine with pump.
16
Engine Mount
Side View
Refer to engine's instruction manual
and set up piping.
3x25mm3x25mm
3mm
3mm
3mm
3mm
3mm
3mm
3mm
3.2
mm
3.2
mm
Throttle Rod
PP Pipe
Engine
4
3mm
Spring Washer
Spring Washer
Spring Washer
4
3 x 25mm
Cap Screw
4
3mm
Washer
3mm
Nut
4
Engine Mount
3mm
3mm
3x25mm
3mm
118mm
3mm
Temporarily install the engine and make a hole for the throttle
rod by aligning with the position of the throttle lever.
Pictures show 4-stroke engine without pump, but engines with pump or 2-stroke engines are installed same way.
Must be purchased separately!
Assemble left and right
sides the same way.
Align to same dimensions as shown above.
Align to engine and make 3.2mm holes.
1
2
4
3
Assemble in the specified
order.
3.2mm
PP
12
Must be purchased separately!
Drill holes with the
specified diameter.
2mm
17
Servo
Rudder ServoThrottle Servo Elevator Sarvo
Throttle Rod
< >Throttle Servo < >Rudder Servo < >Elevator Sarvo
Supplied with the servo. Supplied with
the servo.
Supplied with
the servo.
Refer to the pictures below and install each servo.
approx. 13mm
approx. 13mmapprox. 13mm
18
Linkage
1
3 x 3mm
Set Screw
1
Linkage Stopper
1
Nut
3x3mm
2mm
Throttle Servo
2mm
Switch
Cut off shaded portion.
x3
Assemble as many times
as specified.
approx. 16mm
2mm2mm
Supplied with
the servo.
Supplied with
the servo.
x3
Use the remaining pipe at step .
20
1
2mm
Washer
2mm
< > < > < >
13mm 16mm
13mm13mm
20
Front
13
Drill holes with the
specified diameter.
3mm
3 x 40mm
Screw
2
3mm
Washer
3mm
Nut
3mm
3mm
Washer
3mm
Washer
Nut
3mm
Nut
2
4
2 x 20mm
Screw
2x20mm
95mm
6mm
3mm
3mm
3mm
3mm
3x40mm
3mm
2mm
2x20mm
2mm
< >Top view.
19
Vertical
/
Horizontal Tail
1
3mm
< >
14
Apply epoxy glue.
Assemble left and right
sides the same way.
Cut off shaded portion.
20
Rudder Rod
Cut away film
only, here.
40mm20 3010
0
4
Brass Pipe
Wire Adjuster
2
40mm
File down on an angle.
Left over pipe
from step .
Fasten as per illustration.
Fasten as per illustration.
Rudder Servo
Parallel
Position servos in neutral before
commencing this step.
4
5
1
2
3
Assemble in the specified order.
18
18
15
Must be purchased
separately!
Assemble left and right
sides the same way.
Cut off shaded portion.
22
Elevator Rod
21
Elevator Rod
Heat-shrink Tube
Beware of the flame!
Bend at end of rod.
Be careful not to scorch the heat-shrink tube!
Slide heat shrink tubes over linkage rods
and use a shrink covering heat gun or
similar to secure (shrink) them in place.
Position servos in neutral,
then bend the rods.
2mm
2mm
2mm
Pay close attention here!
Drill holes with the
specified diameter.
2mm
Apply instant glue
(CA glue, super glue).
Cut away film
only, here.
File down with the hole on an
angle so the rods move smoothly.
1
2
3
Assemble in the specified order.
Elevator Servo
5
4
2mm
16
Pay close attention here!
Must be purchased
separately!
Do not overlook this symbol!
Warning!
Drill holes with the
specified diameter.
2mm
Cut off shaded portion.
24
Cowling
Trim the cowling so it will match your engine.
2.6x8mm
2.6x8mm
1~2mm
4
2.6 x 8mm
TP Screw
2mm
2mm
23
Battery
Make certain parts are aligned accurately
and play is reduced to a minimum.
Tighten screws securely.
Battery
Receiver
Receiver
Battery
Warning!
Foam PadFoam Pad
Bind with adhesive
tape.
Bind with adhesive tape.
An end cap for engine pipe is included.
To use, please refer to engine's
instruction manual.
Fuel Tank
Battery
Receiver
4-stroke w/o Pump, & 2-stroke Engines.
For 4-
stroke
Engine with pump.
Refer to engine's instruction
manual and install muffler.
2mm
TP
17
26
Decal
Apply included decals. For the correct placement of decals, please refer to box top.
Drill holes with the
specified diameter.
2mm
25
Canopy
2.6x8mm
2.6x8mm
4
2.6 x 8mm
TP Screw
2mm
2mm
< >Decal
2mm
TP
< >
18
Pay close attention here!
Do not overlook this symbol!
Warning!
27
Adjustment
28
C of G position
Reference point for
diagram at right.
Reference point for
diagram at right.
Reference point for
diagram at right.
Reference point for
diagram at right.
Reference point for
diagram at right.
RUDDER
AILERON
ELEVATOR
50mm
50mm
15mm
15mm
10mm
10mm
Warning!
Do not fly before confirming the correct location of the CG.
If the CG is incorrect, you lose control of your airplane which
leads to accidents!
In order to obtain the CG specified, reposition
the receiver and other equipment.
Adjust the travel of each control surface to the values in the diagrams.
CG
210~185mm
RR
R
R
R
R
No.11852 Oxalys 50 PRINTED IN CHINA
19
EXPLODED VIEW
Screw
2 x 5mm
Screw
2.6 x 18mm
Set Screw
3 x 3mm
Set Screw
3 x 3mm
Cap Screw
3 x 30mm
TP Screw
2 x 8mm
TP Screw
2.6 x 8mm
TP Screw
2.6 x 8mm
TP Screw
2.6 x 8mm
TP Screw
2.6 x 8mm
Mount Nut
4mm
Nut
3mm
Nut
3mm
Washer
3mm
Screw
3 x 40mm
Screw
2 x 20mm
Screw
3 x 25mm
Screw
4 x 20mm
Screw
2 x 20mm
Screw
2 x 20mm
Screw
2 x 20mm
Nut
3mm
Nut
4mm
Washer
4mm
Washer
3mm
Washer
3mm
Cap Screw
3 x 30mm
Washer
3mm
Spring Washer
4mm
Spring Washer
3mm
Spring Washer
3mm
Screw
3 x 12mm
Screw
4 x 35mm
Nut
4mm
20
Do not overlook this symbol!
Warning!
*This aircraft is for intermediate to advanced builders and flyers only. Beginners cannot fly and building this aircraft.
*This aircraft has been flight tested with snap-rolls and other aerobatic maneuvers. However, repeated violent
maneuvers may overstress the airframe. Please fly in a way that will not overstress the airframe.
*Repeated flying can cause stress cracks to appear in the wood and joints. Please inspect after each flight. If any
abnormalities are noted, repair immediately before the next flight to avoid accidents.
*Glue joints become loose even though they appear to be tight. If you notice irregular flight, investigate the cause
and repair it before the next flight.
*As for linkages, inpropely assembling then can result in binding or loose control surfaces. This can cause flutter
and aircraft control problems. Make sure all linkages are tight and control surfaces move properly before flying.
*This aircraft is designed for 2-stroke .46~.50 / 4-stroke .52~.63 sized engines only. Using larger, more powerful
engines is not safe and may result in airframe failure. Do not exceed the recommended engine size or engage in
extreme aerobatic maneuvers.
Warning!
MEMO
ページを読み込んでいます...
ページを読み込んでいます...
/
