Center of hinge
Main body Front (logo) side Main body Back side
Center of flange hook
100 mm
shaft
CK-300 clamps
(sold separately)
Flange hook
Stopper
Flange hook
Protective cap
Straight
U-shaped
Logo
Logo
Table Top Architect System Wind Screen
CK-301
Contents (Name of the Parts) Specifications
Safety Precautions: Before use, please read thoroughly to ensure safety and avoid accidents.
CAUTION: Misuse could result in injury to the user and/or damage to property.
Instruction Manual:
Ver 1.00
Maintenance and disposal
Warranty
Repair
DANGER: Misuse could easily result in a serious accident or death.
WARNING: Misuse could result in serious injury or death.
Main body x 1, Stopper x 3, Flange hook x 4,
Protective cap x 2, 100 mm shaft x 2
CAUTION
Be careful not to cut your hand on the edge of the threaded portion. Do not forget to attach the supplied protective cap when storing the product.
Instructions for Use
This product is designed to be attached to the CK-300 clamps (sold separately). Before assembling, please read the CK-300 clamp instruction manual carefully.
Thank you for purchasing this Snow Peak product. This is a wind screen of the table top architect (TTA) series. It has a four-panel structure that can cover two IGT
units. This product is intended to prevent wind from blowing into the combustion appliance on the table when it is attached to the CK-300 clamps (sold separately) to
secure it to the table. Do not use it for any other purposes.
In order to ensure your safety when using this product, please read the Instruction Manual carefully before use. Please be sure to keep this document for future
reference. If you have any difficulties understanding certain parts of the instruction manual or if you find any product defects, stop using the product immediately and
contact the dealer you purchased the product from or Snow Peak Customer Service.
Material(s) Stainless steel, Galvalume steel plate, Silicon rubber,
Polypropylene
Size
760 mm (L) x 26 mm (W) x 226 mm (H) / 30"(L)×1"(W)×8.9"(H)
Weight 800 g / 1.8 lbs
Before using the product, check each part for abnormalities. If you find any abnormalities, stop using the product immediately and contact the retailer where you
purchased the product or Snow Peak Customer Service for inspection or repairs.
Do not use when there is extremely strong wind. The product may be deformed by the wind or fall over together with the table, resulting in a fire or accident.
Be careful not to cut your hand on the edge of the threaded portion.
After assembly, check for wobbling, and loose, screws and clamp bolts. Also,
regularly check the screws and bolts for looseness during use. If this product
is used while it is wobbly or screws and bolts are loose, parts may fall off or
objects may fall, which may result in personal injury or product damage.
Do not use this product if it cannot be assembled as described in the
Instruction Manual due to deformation or rust. If this product is used for a
long period of time, it may become deformed or rust, which may prevent
screws from turning smoothly or cause the product to become unstable when
assembled. If you continue to use this product in such a state, it may fall
apart or parts may come off, which may result in personal injury or product
damage.
Please note that this product will become hot if used in a place exposed to
direct sunlight for a long period of time, particularly under scorching sun.
When using this product outdoors, use it in a place where it will not be
exposed to rain, such as under a tarp. If you leave this product wet with
rainwater for a long period of time, the screws and joints may rust, which may
lead to discoloration and sticking.
Do not assemble or disassemble this product when it is wet or with wet
hands. Otherwise, an injury may result.
The product should be assembled by a person who is capable of
understanding the Instruction Manual, has a sufficiently strong grip, and who
has the ability to assemble it correctly.
Do not adjust the mounting position or move the product while it is still
assembled. If you loosen the clamp while the product is being assembled, the
product may fall off, which may result in personal injury or product damage.
Do not remove this product from the table with the CK-300 clamps still attached
to it when transferring the product. Otherwise, it may cause a distortion.
Use this product on a flat and stable surface. If it is used on an angled or unstable
surface, the product may fall, resulting in personal injury or product damage.
Also, read the instruction manual for the table, and use this product correctly.
When using this product near a heat source, do not touch it as it will be hot.
Also, after use, do not touch the product until you know that it has cooled
down sufficiently. Otherwise, it may cause burns.
After assembling this product, check that it will not easily come off the table.
This product is not intended for permanent use. Clean up immediately after
use and store in a well-ventilated place out of the reach of children.
This product cannot be used with cast iron products such as Dutch ovens.
The heat may result in burns, fire, or damage. If professional repairs are required, please contact the retailer where you purchased the product or Snow Peak Customer Service.
When you request repairs, please make sure that the product is dry and clean.
Please attach a memo or a tag indicating the necessary repairs and write details of how and when the damage occurred.
Transportation and repair costs are determined as follows.
1. When warranty applies: The transportation cost (both ways) and repair cost
will be covered by Snow Peak.
2. When warranty does not apply: The transportation cost (both ways) and
repair cost will be covered by the customer.
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. inf[email protected] / www.snowpeak.com
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find any product defects, please contact the retailer
where you purchased the product or Snow Peak Customer Service. If there are apparent defects due to the product's manufacturing, the defective product will be
repaired or exchanged free of charge. In other cases, Snow Peak will repair the product for an appropriate fee. The decision to repair or replace the product will be
at our discretion. Snow Peak will not repair the product for any damage that occurred due to the following:
1. Material deterioration caused by age
2.
Damage caused by modifications or rough handling
3. Damage caused by inappropriate use not
mentioned in the instruction manual
4. Damage caused by unexpected accidents
5. Any damage other than defects in the
manufacturing process
6. Damage caused by dust or rust
7. Damage and defects caused by dismantling the
product
8. Damage and defects caused by dropping,
jolting or other shocks
9. Deterioration or failure of parts due to friction
10.
Damage caused by the use of the product in
combination with another manufacturer's products
When disposing of this product, follow the rules of the local government of your area.
When using the product after not using it for a long period of time, inspect it and make sure that there are no abnormalities in each part. If you find any abnormalities,
stop using the product immediately and contact the retailer where you purchased the product or Snow Peak Customer Service for inspection or repairs.
After use, follow the procedure described below to appropriately clean and store the product. Not cleaning dirt or moisture off the product may cause rust to form.
After use, disassemble the product and clean it using a dry cloth.
If the product is wet, disassemble it, wipe it, and dry it well.
If salt, seasonings, or other substances are adhered to the product, wipe them off thoroughly using a tightly wrung cloth and allow it to dry thoroughly.
If you use this product in a location exposed to sea breezes such as a beach, disassemble it, wipe it thoroughly using a tightly wrung cloth, and dry it well.
Unfold the main body and slide the three stoppers to attach the main body as
illustrated.
Adjust each stopper so that it is positioned in the center of the hinge.
Attach the supplied flange hooks to the four holes in the main body. Fit a flange
hook from the back side of the main body by aligning it to the shape of the
hole, and rotate it 90 degrees.
After attaching all the flange hooks, be sure to visually check that the top and
bottom centers are aligned. If they are misaligned, adjust their positions.
Turn the 100 mm shaft clockwise until there is no slack, and attach it to each
CK-300 clamp.
To determine the position to attach the windscreen, make sure that the table is
clean, then temporarily attach the CK-300 clamps to the table.
At this time, temporarily attach the CK-300 clamps using a moderate tightening
force so that it can be moved left and right.
*
Be sure to check the instructions for use in the CK-300 clamp instruction manual.
Attach each of the left and right flange hooks of the windscreen body to each of
the 100 mm shafts attached to the CK-300 clamps.
If the 100 mm shafts and the flange hooks are misaligned, adjust the positions
of the temporarily attached CK-300 clamps, or adjust the positions of the flange
hooks on the main body.
Tighten the temporarily attached CK-300 clamps until there is no slack.
Finally, check the windscreen body again for any looseness.
CAUTION
Use this product in the configuration shown on the
left. If you rearrange the configuration or combine
them with products manufactured by other
companies, the product will become unstable and
may tip over resulting in personal injury or product
damage.
Keep an eye on small children if they are nearby. If children play with this product, it may result in unexpected accidents.
Be sure to use the CK-300 clamps (sold separately) to attach the product to the table. If you use other means to attach this product, it may tip over, resulting in
personal injury or product damage.
* You can use the product in a U-shape by using the main body
upside-down. When attaching on a table in the U-shape, attach
the windscreen body between the combustor and the CK-300
clamps. Failure to do so may cause the product to become hot
and cause burns, deformation, or damage.
For removal, do the procedure in the reverse order.
When storing, attach the protective caps to the threads of the 100 mm shafts.
Snow Peak Customer Service
(9:00-17:00)
+1(503)461-0781
Email: inf[email protected]
If you have any questions or concerns,
please contact your retailer or Snow
Peak customer service.
/
