TTA Sierra Cup Holder
CK-306
Instruction Manual : Ver 1.00
●Materials : Stainless steel
●Size : 160×125×18(h)mm / 6.3"×4.9"×0.7"(h)
●Weight : 135g / 0.3 lbs
●Maximum loading weight : 1kg / 2.2 lbs
Specifications
Contents (Name of the Parts)
Thank you for purchasing a Snow Peak product. This product is a cup holder for the Sierra Cup. For safety, read the following instruction manual before use. Please keep it safe for future reference. Finally,
if you find anything that you do not understand in the description or any problems with the product, please stop use immediately and contact the retailer or Snow Peak Customer Service.
Safety Precautions: Before use, please read thoroughly to ensure safety and avoid accidents.
DANGER / Misuse could easily result in a serious accident or death.
● Keep an eye on small children when they are nearby. Children playing with the product may cause unexpected accidents.
WARNING / Misuse could result in serious injury or death.
●Before using the product, check each part for abnormalities. If there are abnormalities, take the product to the dealer or Snow Peak
Customer Service for inspection or repair.
●Do not use near heat sources such as stoves or barbecue boxes. The unit may become hot, resulting in burns or ignition of items.
●When stacking Snow Peak stainless steel Sierra Cups on this product, the total weight should not exceed 1kg2.2lbs and the
maximum number of cups should not exceed ten. Stacking more than that may cause them to fall out or damage the product. Even
within 10 cups, the product may be unstable depending on the installation. After installation and assembly, be sure to inspect the
product for any wobbling and confirm that it is stable before use.
●When using in combination with the Tabletop Architect(TTA) series, be sure to read the instruction manual of the other product(s)
carefully and observe the maximum loading weight.
CAUTION / Misuse could result in injury to the user and/or damage to property.
●Use in combination with products other than the TTA series or products of other manufacturers may result in injury or damage to the
product due to instability.
●After assembling this product, check for any wobbling of the main unit and any looseness in the clamps and other extension parts.
Also, periodically check each screw piece for looseness during use. Using the product with wobbling or loose screws may cause parts
to fall off, resulting in injury or damage to the product.
●Be careful if the product is used in places where it is exposed to direct sunlight under the blazing sun for long periods of time, the
product will become hot.
●When using the product outdoors, use it under a tarp or in a location where it will not be exposed to rainwater. Leaving the product wet
with rainwater for an extended period will cause rust to form on the screws and joints, resulting in discoloration and poor functionality.
●Be sure to remove any objects placed on the holder before adjusting, moving or securing the mounting position.
●Do not subject the product to strong impacts such as dropping. Strong impacts may deform or damage the product.
●Cannot be attached to the crankshaft of CK-302TTA lantern hanger due to the risk of tipping over.
Snow Peak, Inc.
456, Nakanohara, Sanjo-Shi, Niigata 955-0147 Japan
Tel. +81 256-46-5858 / Fax. +81 256-46-5860
www.snowpeak.co.jp
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. info@snowpeak.com / www.snowpeak.com
Maintenance
●Before use, wash it with the soft side of a sponge dipped in neutral detergent. Using a scrubber or the rough side of a sponge may cause scratches.
●After use, wash the product with a neutral detergent, remove water with a soft cloth or towel, and dry it in a shaded, well-ventilated area. Dirt and moisture left on the surface may cause rust.
●Do not use a dishwasher or dryer for this product.
●If professional repairs are required, please contact the retailer where you purchased the product or Snow Peak Customer Service.
●When you request repairs, please make sure that the product is dry and clean.
●Please attach a memo or a tag indicating the necessary repair and please write details of how and when the damage occurred.
●Transportation and repair costs are determined as follows.
1. Within warranty: The transportation cost (both ways) and repair cost will be covered by Snow Peak.
2.Outside warranty: The transportation cost (both ways) and repair cost will be covered by the customer.
Repair
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find any product defects, please contact the retailer where you purchased the product or Snow
Peak Customer Service. If there are apparent defects in the product's manufacturing, the defective product will be repaired or exchanged free of charge. In other cases, Snow Peak will repair the product for
an appropriate fee. The decision to repair or replace the product will be at our discretion. Snow Peak will not repair the product for any damage that occurred due to the following:
1.Material deterioration caused by age
2.Damage caused by modifications or rough handling
3.Damage caused by inappropriate use not mentioned in the instruction manual
4.Damage caused by unexpected accidents
5.Any damage other than defects in the manufacturing process
Warranty
6.Damage caused by dust or rust
7.Damage and defects caused by dismantling the product
8.Damage and defects caused by dropping, jolting or other shocks
9.Deterioration or failure of parts due to friction
10.Damage caused by the use of the product in combination with another manufacturer's products
Instruction manual
(This manual)
Mounting bolt
Main unit
300mm Shaft
(Sold separately)
CK-300 TTA Clamp
(Sold separately)
Instructions for Use
This product is designed to be assembled with a shaft of 8 mm in diameter, such as the 300 mm shaft which is included in CK-302 TTA Lantern Hanger and CK-303 TTA Unit Frame. It cannot be used with
products other than the Tabletop Architect series or products of other manufacturers. Be sure to read and understand the instruction manuals of complementary products before assembling. This manual
explains an example of installation on a 300 mm shaft attached to a CK-300 TTA Clamp.
※Cautionary points for assembly
If this product is installed facing outward from the table as shown in the figure, it may fall. Be sure to install the product on top of the table, failure to do so may result in damage to items or injury.
Before installing this product, check to ensure the clamps and shafts are securely tightened without loosening.
Turn the mounting bolt counterclockwise from the main unit and remove it. *Be careful not to lose the mounting bolts.
Mount the main unit on the 300 mm shaft. Place it on any position on the 300 mm shaft to determine the best mounting position. Reattach and turn the mounting bolt that was removed in step clockwise
into the screw hole on the main unit to secure it in place. If the tightening force is not strong enough, the bolt will fall off. Tighten the mounting bolts securely until they no longer turn.
Finally, check the clamp, shaft threads, and this product again for any looseness. Re-tighten any loose parts.
Follow the reverse procedure to disassemble.
Turn clockwise
Screw Hole
Rotate
counterclockwise
/
