Snow Peak CK-303 取扱説明書

  • こんにちは!snow peak テーブルトップアーキテクトCK-303ユニットフレームの取扱説明書を読みました。このデバイスの組み立て、使用方法、安全上の注意事項、メンテナンス方法などについてご質問があれば、お気軽にお尋ねください。
  • CK-300クランプは付属していますか?
    組み立て中にぐらつきがあった場合はどうすればよいですか?
    屋外で使用する場合の注意点は?
    本製品の最大の積載重量は?
CK-303
0120-010-660
Ver 1.00
300 mm
shaft U-shaped
bracket
CK-300
clamp
(sold separately)
Joint bolt
Joint bolt
* This product does
not come with the
CK-300 clamps.
Clamp
screw hole
300 mm shaft
Fix the clamp so that
it can be moved to the
left and right
Fix
300 mm shaft
Clamp screw hole
Joint bolt
Screw hole of 300 mm
shaft
U-shaped bracket
Fully tighten the
temporarily fixed bolt.
Material(s) Stainless steel
Size 333 mm (L) × 12 mm (W) × 480 mm (H)/13.11" (L) ×
0.47" (W) × 18.89" (H)
Weight 580 g/1.27 lb
Maximum load weight 2 kg/4.40 lb
when used alone
Table Top Architect Unit Frame
CK-303
Contents (Name of the Parts) Specifications
CAUTION: Misuse could result in injury to the user and/or damage to property. Maintenance and disposal
Warranty
Repair
DANGER: Misuse could easily result in a serious accident or death.
WARNING: Misuse could result in serious injury or death.
<Unit Frame> U-shaped bracket x 2, 300 mm shaft x 2,
Instruction Manual (this document) x 1
Thank you for purchasing this Snow Peak Product. This is a unit frame of the table top architect (TTA) series. This product is intended for hanging kitchen utensils or as a support
for other TTA-specific extension parts by attaching it to optional clamps and fixing it to the table. Do not use it for any other purposes. In order to ensure your safety when using
this product, please read these instructions carefully before use. Please be sure to keep this document for future reference. If you find anything in the instruction manual that is
difficult to understand, or if you find any product defects, stop using it immediately and contact the dealer where you purchased the product, or Snow Peak Customer Service.
Before using the product, check each part for abnormalities. If there are abnormalities, take the product to the dealer or Snow Peak Customer Service for
inspection or repair.
Do not use this product near heat sources such as a burner or petroleum equipment. Doing so will heat this product up, which will make it a hazard.
Be careful not to cut your hand on the edge of the threaded portion.
After assembly, check for wobbling, and loose screws and clamp bolts. Also,
regularly check the screws and bolts for looseness during use. If this product
is used while it is wobbly or screws and bolts are loose, parts may fall off or
objects may fall, which may result in personal injury or product damage.
Do not use this product if it cannot be assembled as described in the
Instruction Manual due to deformation or rust. If this product is used for a long
period of time, it may become deformed or rust, which may prevent screws
from turning smoothly or cause the product to become unstable when
assembled. If you continue to use this product in such a state, it may fall apart
or parts may come off, which may result in personal injury or product damage.
Please note that this product becomes hot if used in a place exposed to
direct sunlight for a long period of time, particularly under scorching sun.
When using this product outdoors, use it in a place where it will not be exposed to rain,
such as under a tarp. If you leave this product wet with rainwater for a long period of
time, the screws and joints may rust, which may lead to discoloration and sticking.
Do not assemble or disassemble this product when it is wet or with wet
hands. Otherwise, an injury may result.
The product should be assembled by a person who is capable of
understanding the Instruction Manual, has a sufficiently strong grip, and who
has the ability to assemble it correctly.
While this product is attached, do not attempt to adjust the attachment position,
or move it. If you loosen the clamp while the product is being assembled, the
product may fall off, which may result in personal injury or product damage.
Do not remove this product from the table with the CK-300 clamps still attached
to it when transferring the product. Doing so may distort the shape of this product.
Use this product on a flat and stable surface. If it is used on an angled or unstable
surface, the product may fall, resulting in personal injury or product damage.
Also, read the instruction manual for the table, and use this product correctly.
After assembling this product, check that it does not easily come off the table.
This product is not intended for permanent use. Clean this product immediately
after use, and keep it out of the reach of children.
If professional repairs are required, please contact the retailer where you purchased the product or Snow Peak Customer Service.
When you request repairs, please make sure that the product is dry and clean.
Please attach a memo or a tag indicating the necessary repair and please write details of how and when the damage occurred.
Transportation and repair costs are determined as follows.
1. Within warranty: The transportation cost (both ways) and repair cost will be covered by Snow Peak.
2. Outside warranty: The transportation cost (both ways) and repair cost will be covered by the customer.
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find any product defects, please contact the retailer
where you purchased the product or Snow Peak Customer Service. If there are apparent defects in the product's manufacturing, the defective product will be
repaired or exchanged free of charge. In other cases, Snow Peak will repair the product for an appropriate fee. The decision to repair or replace the product will be
at our discretion. Snow Peak will not repair the product for any damage that occurred due to the following:
1. Material deterioration caused by age
2.
Damage caused by modifications or rough handling
3. Damage caused by inappropriate use not
mentioned in the instruction manual
4. Damage caused by unexpected accidents
5. Any damage other than defects in the
manufacturing process
6. Damage caused by dust or rust
7. Damage and defects caused by dismantling
the product
8. Damage and defects caused by dropping,
jolting or other shocks
9. Deterioration or failure of parts due to friction
10.
Damage caused by the use of the product in
combination with another manufacturer's products
Before using a product that has been in storage for a long time, check each part for abnormalities. If there are abnormalities, take the product to the retailer or
contact Snow Peak Customer Service for inspection or repair.
After use, follow the procedure described below to appropriately clean and store the product. Not cleaning dirt or moisture off the product may cause rust to form.
After use, disassemble the product and clean it using a dry cloth.
If the product is wet, disassemble it, wipe it, and dry it well.
If salt, seasonings, or other substances are adhered to the product, wipe them off thoroughly using a tightly wrung cloth and allow it to dry thoroughly.
If you use this product in a location exposed to sea breezes such as a beach, disassemble it, wipe it thoroughly using a tightly wrung cloth, and dry it well.
When disposing of this product, follow the rules of the local government of your area.
Turn the 300 mm shaft clockwise to tighten in the same way as in step , and
fix it to the CK-300 clamp that has been temporarily fixed in step .
Insert U-shaped bracket joint bolt into the screw hole of the 300 mm shaft, rotate
it clockwise, and tighten both sides in order. If the screw holes of the joint bolts
do not match, adjust the position of the CK-300 clamp that was temporarily fixed
in step to the left or to the right, and tightly screw it in both the left and right
joints of the U-shaped bracket until there is no looseness.
In the same way, attach the U-shaped bracket joint to the screw hole at the
bottom of the clamps until there is no looseness and so that it does not wobble.
Tighten the clamp that has been temporarily fixed until there is no looseness.
Finally, check it again for any looseness.
To remove it, implement the attachment procedure in reverse.
Safety Precautions: Before use, please read thoroughly to ensure safety and avoid accidents.
Instructions for Use
This product is designed to be attached to the CK-300 clamps (sold separately). Before assembling, please read the CK-300 clamp instruction manual carefully.
Attach one CK-300 clamp unit to the top plate of the table, and be sure to check
that it does not wobble.
Then, tighten the 300 mm shaft clockwise into the screw hole of one CK-300 clamp.
Please note that the clamp may not come off if the shaft is tightened excessively.
Tighten the other CK-300 clamp to the point where it can be moved to the left
and right, and temporarily fix it to the table.
CAUTION
Be careful not to cut your hand on the edge of the threaded portion.
Snow Peak Customer Service
(9:00-17:00)
+1 503-697-3330
If you have any questions or concerns,
please contact your retailer or Snow
Peak customer service.
Instruction Manual: Ver 1.00
CAUTION
Use this product in the form shown on the left. When you combine this product
with other TTA-specific extension parts, use it in the form described in the
instruction manual of the extension parts. If you rearrange this product into
another form or combine it with another company's product, it may become
unstable and fall off, which may result in personal injury or product damage.
Keep an eye on small children if they are nearby. If children play with this product, it may result in unexpected accidents.
Be sure to use the CK-300 clamps (sold separately) to fix this product to a table. If you use other means, the product may fall, resulting in personal injury or product damage.
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. inf[email protected] / www.snowpeak.com
/