Nut
Movable width
1 to 35 mm/0.03" to 1.37"
Bolt
Arm
Rubber
pad
Flat part of arm
Flat part of arm
Flat part of nut
Flat part of nut
Flat part of arm
Flat part of nut
Rubber pad surface
Turn counterclockwise
and tighten
Thank you for purchasing this Snow Peak Product. This is a clamp that is a base part of the table top architect (TTA) series. Please attach this product to the Snow Peak table and use
it in combination with TTA series extension parts. This product should not be used in combination with products other than TTA series extension parts. In order to ensure your safety
when using this product, please read these instructions carefully before use. Please be sure to keep this document for future reference. If you find anything in the instruction manual
that is difficult to understand, or if you find any product defects, stop using it immediately and contact the dealer where you purchased the product, or Snow Peak Customer Service.
Readjusting the nuts and bolts
Readjust each part of the clamp according to the thickness of the table by
referring to the figures of Type A, Type B, and Type C. This product is packed
as shown in Type A when you open the box. This section describes how to
readjust the nuts and bolts to Type C to be used with the IGT frame that has a
25 mm/0.98" thick top plate.
Align the flat part of the nut with the flat part of the arm in parallel, and remove
the nuts and bolts from the arm. The nut and bolt are designed to come off
easily when they are aligned with the flat part of the arm.
Rotate the bolt counterclockwise and remove it from the nut. Attach the
removed bolt to the opposite end of the nut.
How to attach this product to the top plate
As shown below, after confirming that the table is clean, temporarily position
the clamp. While pressing the upper nut vertically against the table, rotate it
counterclockwise and tighten it onto the table. (Tighten the clamp unit until it
does not wobble when you wiggle the clamp. If it is tightened excessively, you
may not be able to remove the clamp when you want to.) Before installing the
separately sold TTA series products, check it again for rattling, and make sure
that the product is securely attached.
Removal
Remove this product by implementing the attachment procedure in reverse.
Attach the nut and bolt to the arm by implementing the removal procedure in reverse.
Align the flat part of the nut and bolt with the flat part of the arm so that the upper
and lower rubber pad surfaces are facing the inside (top plate side). The rubber
pads have a non-slip function. Make sure that the rubber pads firmly come in
contact with the top plate of the table so that the product will not come off the table.
Table Top Architect Unit Clamp Tool
CK-300
Contents (Name of the Parts Specifications
Safety Precautions: Before use, please read thoroughly to ensure safety and avoid accidents.
Instructions for Use
CAUTION: Misuse could result in injury to the user and/or damage to property.
Please use this product in combination with TTA series extension parts. If you use
this product in combination with products other than TTA series extension parts, it
may become unstable and fall, and result in personal injury or product damage.
When you use this product in combination with TTA series extension parts,
be careful not to cut your hand on the edge of the threaded portion.
After assembling the TTA, check for wobbling, and loose screws and clamp
bolts. Also, regularly check the screws and bolts for looseness during use. If this
product is used while it is wobbly or screws and bolts are loose, parts may fall off
or objects may fall, which may result in personal injury or product damage.
Do not use this product if it cannot be assembled as described in the
Instruction Manual due to deformation or rust. If this product is used for a long
period of time, it may become deformed or rust, which may prevent screws
from turning smoothly or cause the product to become unstable when
assembled. If you continue to use this product in such a state, it may fall apart
or parts may come off, which may result in personal injury or product damage.
Please note that this product becomes hot if used in a place exposed to
direct sunlight for a long period of time, particularly under scorching sun.
When using this product outdoors, use it in a place where it will not be exposed to rain,
such as under a tarp. If you leave this product wet with rainwater for a long period of
time, the screws and joints may rust, which may lead to discoloration and sticking.
Do not assemble or disassemble this product when it is wet or with wet
hands. Otherwise, an injury may result.
The product should be assembled by a person who is capable of
understanding the Instruction Manual, has a sufficiently strong grip, and who
has the ability to assemble it correctly.
Check that the non-slip rubber is not worn before assembling. If the rubber is
worn, the product will not be able to be firmly attached and may fall off, which
may result in personal injury or product damage.
While this product is attached, do not attempt to adjust the attachment position,
or move it. If you loosen the clamp while the product is being assembled, the
product may fall off, which may result in personal injury or product damage.
After assembling this product, check that it does not easily come off the table.
This product is not intended for permanent use. Clean this product immediately
after use, and keep it out of the reach of children.
Use this product on a flat and stable surface. If it is used on an angled or unstable
surface, the product may fall, resulting in personal injury or product damage.
Also, read the instruction manual for the table, and use this product correctly.
Do not store the clamp in a hot location such as inside a car. Otherwise, the
rubber may deteriorate due to the heat.
Do not leave or store the clamp while it is attached to a table. Otherwise,
traces of the rubber of the clamp may be left on the table, or the rubber may
peel off and stick to the table. Especially in places such as inside a car where
temperatures can become high, the heat may dissolve the rubber, which may
leave a trace of the rubber or cause the rubber to peel off easily.
Instruction Manual: Ver. 1.00
Maintenance and disposal
Warranty
Repair
Material(s) Stainless steel, rubber material
Size 56 mm (L) × 52 mm (W) × 100 mm (H)/2.20" (L) ×
2.04" (W) × 3.93" (H)
Weight 310 g/0.68 lb
Clamp movable width 1 to 35 mm/0.03" to 1.37"
DANGER: Misuse could easily result in a serious accident or death.
Keep an eye on small children if they are nearby. If children play with this product, it may result in unexpected accidents.
WARNING: Misuse could result in serious injury or death.
Before using the product, check each part for abnormalities. If there are abnormalities, take the product to the dealer or Snow Peak Customer Service for inspection or repair.
Do not use this product near heat sources such as a burner or petroleum equipment except when using a windscreen (sold separately).
Do not attach this product to an incompatible table. If you use this product on an unstable table or if the entire surface of the rubber pads of the clamp cannot grip
the table, the table or the TTA may tip over, which may cause an injury, burns, or fire.
Please attach this product to the Snow Peak table. However, please note that this product should not be attached to the following products due to the risk that it might
fall off or due to table structural reasons. Never attach this product to a table of an incompatible product number; otherwise, the table may tip over, which may cause an
injury, burns, or fire.
Check the thickness of your table before attaching this product, and readjust the position of the nut and bolt, if necessary.
<Clamp> Main body x 1, Instruction Manual
(this document) x 1
Non-compliant product number
Product No. Product name Reason
LV-034TR MYTABLE BAMBOO TOP Risk of tipping over
LV-039 TAKIBI My Table Risk of tipping over
GF-015 GARDEN UNIT TABLE Non-compliant dimensions
LV-310 STAINLESS KITCHEN TABLE Non-compliant dimensions
CK-153TR IGT SLIDE TOP HALF Risk of tipping over
CK-154TR IGT SLIDE TOPLONG HALF Risk of tipping over
CK-090 Extension IGT Risk of tipping over
Type A
Case where the thickness
of the top plate is
less than 10 mm/0.39"
Type B
Case where the thickness
of the top plate is
10 to 20 mm/0.39" to 0.78"
Type C
Case where the thickness
of the top plate is
20 to 35 mm/0.78" to 1.37"
If professional repairs are required, please contact the retailer where you purchased the product or Snow Peak Customer Service.
When you request repairs, please make sure that the product is dry and clean.
Please attach a memo or a tag indicating the necessary repair and please write details of how and when the damage occurred.
Transportation and repair costs are determined as follows.
1. Within warranty: The transportation cost (both ways) and repair cost will be covered by Snow Peak.
2. Outside warranty: The transportation cost (both ways) and repair cost will be covered by the customer.
Before using a product that has been in storage for a long time, check each part for abnormalities. If there are abnormalities, take the product to the retailer or
contact Snow Peak Customer Service for inspection or repair.
After use, follow the procedure below to appropriately clean the product, and store it with the bolts inserted into the nuts. Not cleaning dirt or moisture off the product
may cause rust to form.
After use, disassemble the product and clean it using a dry cloth.
If the product is wet, disassemble it, wipe it, and dry it well.
If salt, seasonings, or other substances are adhered to the product, wipe them off thoroughly using a tightly wrung cloth and allow it to dry thoroughly.
If you use this product in a location exposed to sea breezes such as a beach, disassemble it, wipe it thoroughly using a tightly wrung cloth, and dry it well.
When disposing of this product, follow the rules of the local government of your area.
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find any product defects, please contact the retailer
where you purchased the product or Snow Peak Customer Service. If there are apparent defects in the product's manufacturing, the defective product will be
repaired or exchanged free of charge. In other cases, Snow Peak will repair the product for an appropriate fee. The decision to repair or replace the product will be
at our discretion. Snow Peak will not repair the product for any damage that occurred due to the following:
1. Material deterioration caused by age
2. Damage caused by modifications or rough
handling
3. Damage caused by inappropriate use not
mentioned in the instruction manual
4. Damage caused by unexpected accidents
5. Any damage other than defects in the
manufacturing process
6. Damage caused by dust or rust
7. Damage and defects caused by dismantling
the product
8. Damage and defects caused by dropping,
jolting or other shocks
9. Deterioration or failure of parts due to friction
10. Damage caused by the use of the product in
combination with another manufacturer's
products
CAUTION
Be careful not to cut your hand on the edge of the threaded portion.
Snow Peak Customer Service
(9:00-17:00)
+1 503-697-3330
Email: inf[email protected]
If you have any questions or concerns,
please contact your retailer or Snow
Peak customer service. Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. inf[email protected] / www.snowpeak.com
-
1
-
2
