Hook Firmly
Fig. A
Pocket
Reinforcement
Bar
1 Unit
Knob
Fixing Pin
Fixing Hole A
Fixing Hole B
Tabletop
Mark
SpecificationContents Include
●Material: Tabletop / Bamboo Laminated
Wood, Stand / Aluminum Alloy, Stainless
Steel, Steel, Resin
●Usable Size : (Maximum) 1348 (53.1”) x
498 (19.6”) x 400 (15.7”) (h) mm, (Minimum)
840 (33.1”)×498 (19.6”)
●Storage Size : 840 (33.1”) x 498 (19.6”) x 67
(2.6”) (h) mm
●Weight : 11 kg (24.3 lbs)
Safety Precaution: Read the following instructions thoroughly before use to assure safety.
How to Use
Setup and Storage
Opening / Closing The Tabletop (When closing, remove all IGT units and then reverse the procedure.)
Installation of Tabletop Protection Parts
Maintenance
●When using this product after a long period of storage, please contact Snow Peak
Customer Service for inspection. ●Always keep the legs near the movable shaft clean. If
the product is opened or closed with sand, dust, or dirt on it, it may stick, rattle, or damage
the product. ●If moisture or salt sticks to the product, wipe it off immediately, and dry the
product thoroughly. ●Occasionally apply lubricating oil around the movable shaft of the leg
to prevent rust and allow it to move smoothly.
●This product is designed for the Iron Grill Table (IGT) as a table and frame for cookers. Safety is fully taken into consideration, but incorrect use may cause an accident
such as a fall, fire, or burns. Please read this manual fully to ensure safe and proper use.
●Our IGT unit products can be inserted into the frame. The basic IGT unit size is (1 unit = S) 250 (9.8”) x 360 (14.2”) mm and (2 unit = W) 500 (19.7”) x 360 (14.2”) mm.
You can select and combine various units.
Frame
Legs
Main Unit Tabletop Protection Parts x 2 Carry Bag Instruction Manual
●The legs can only be opened as far as the Reinforcement Bar can reach. Do not open it forcibly as it may damage the product.
● Be careful not to get your fingers caught in the moving parts.
How to Store the Product
(1) Remove all the built-in IGT units.
(2) Close the Tabletop completely and ensure it is locked in place, then turn the Main Unit over.
(3) Fold the Legs in the reverse order of setup.
(4) The Tabletop Protection parts can be stored in the pocket inside the Storage Case. (Fig. A)
pen the Tabletop and ensure it is securely fixed.
Tabletop
Turn the Main Unit over and raise the Legs then
rotating them in the direction of the arrow. Repeat
the process with the Legs on the other side.
Turn the Main Unit over to finish installation.
Please use it as a table in this state.
After confirming that the Tabletop is securely fixed,
install the IGT insert that is 1 unit size in the center of
the table.
By opening the Tabletop on the opposite side in the
same way, a total of 2 IGT units can be installed.
Install the IGT unit after attaching the Tabletop Protection
Parts to both sides.
Set the Reinforcement Bar in place, as shown above (4 places).
Pull the Knob downwards and rotate it
about 90 ° to lock the Fixing Pin.
When installing an IGT unit that has a heat
source such as a stove or burner, be sure
to attach the included Tabletop Protection
parts.
●Be sure to remove the IGT unit when sliding the Tabletop. Forcibly moving the Tabletop may
damage the product or cause an unexpected accident.
●If you slide the Tabletop without locking the Fixing Pin, the Tabletop will be scratched.
Place it on the frame with the mark of the
Tabletop Protection parts facing upwards, and
mount it so that the Tabletop is sandwiched.
Slide the Tabletop to the side until it stops, rotate the Knob
about 90 °, and insert the Fixing Pin into the Fixing Hole B.
Note
Note
Note
Snow Peak guarantees the quality of its products; please contact your local Snow Peak dealer if you have any problems. Snow Peak will replace or repair if the product is shown
to be originally manufactured defective. Snow Peak appreciates your understanding if any of the following conditions are true, we may not able to repair the product, or in some
cases may charge a reasonable amount for repair.
1. Products lifetime expires due to material changing in quality naturally with time. / 2. Damage by altering or careless handling. / 3. Damage due to handling that is specifically
prohibited in the instruction manual. / 4. Product failure due to user accidents. / 5. Any damage except with product defects due to manufacturing. / 6. Damage by dirt and rust. /
7. Damage by disassembly. / 8. Damage and defects caused by dropping or other shocks to the products. 9. Defects, breakage or deterioration of replaceable parts. 10. Damage
caused by use of the product in combination with other maker’s products.
Warranty
Thank you for purchasing this Snow Peak product. This product is a table for outdoor use. Please read this instruction manual before using it and keep this instruction
manual for future reference. Please confirm all components and set up instructions before using them. If you are not clear on any point, contact your local Snow Peak
Dealer before using.
Danger / Incorrect handling may result in death or serious injury to the user.
Warning / Misuse could result in serious injury or death to the user.
Caution / Indicates actions that may lead to injury, damage to this product, or damage to other items.
●This product is designed as a table and frame for cookware. Please do not use it for any other purpose.
●When installing an IGT unit with a heat source (such as a burner or stove), be sure to use it with the included Tabletop Protection parts.
●Use in a flat place with solid ground, and avoid uneven places or slopes.
●Do not rub the product with metal, hard or abrasive objects. Doing so may cause damage or peeling of the paint.
●Please note that improper handling may cause injury, burns, or damage to the product.
●Do not tip over, drop, or hit this product. Strong impacts and jolts may cause damage.
●The Tabletop of this product may become warped, distorted, or cracked depending on the usage and storage conditions. Do not store or use the product in a place
with high heat, in a place exposed to direct sunlight for long periods, or in a car during the summer.
●Do not cut things directly on the Tabletop as the surface may be scratched.
●If the coating film on the Tabletop is damaged, it will easily absorb moisture, which may cause stains, discoloration, warpage, or distortion.
●The surface of the Tabletop may become discolored after repeated use. Also, an increase in temperature may cause discoloration to progress.
●Placing a hot pot on the Tabletop may cause it to burn.
●The Tabletop of this product is made with processed natural bamboo. The color shade and texture are unique characteristics. Please enjoy the natural color and texture.
●Arrange the IGT cooking units (stoves or burners) so that they are not next to each other.
●The legs are painted black. If the product comes into contact with hard or pointed items or rubs against abrasive objects, the paint may come off.
●Please note that if you store this product with food fragments or seasonings remaining, the metal parts may corrode or mold may form on the Tabletop.
●Before use, inspect the product and check each part for abnormalities. If any abnormalities are found, stop using the product immediately and contact the dealer
where the product was purchased or Snow Peak Customer Service for inspection or repair.
●Please check the legs to ensure there are no defects.
●Do not install BBQ boxes that use charcoal. Doing so may cause the Tabletop to burn from sparks or charcoal.
●When replacing the IGT unit or changing the setup, make sure that the Main Unit and IGT unit inserts are fully cooled to avoid burns.
●Never move the product while the IGT unit is in use. Always remove the IGT unit insert before moving the product.
●When using this product, ensure all the legs are firmly placed on flat ground, and only use it with a weight of 30 kg (66.1 lbs) or less.
●Under the scorching sun and depending on the IGT unit insert, the Main Unit, Protection, and surroundings may become hot. Please be careful to avoid burning yourself.
●Keep this product away from the reach of children.
●When installing an IGT unit with a gas burner, do not use it under or near flammable objects such as tents, tarps, or dry grass.
●Do not use the table for support when standing up, and do not sit on it. Doing so may cause injury or damage.
●Please ensure the leg is secured with the reinforcing bar before use (refer to the set up and storage section). Also, make sure that the legs are fully opened on each
side during use.
●Never modify this product, doing so impairs function and reduces strength.
●When inserting Iron Grill Table (IGT) unit items into this product, please carefully read the instruction manual of each unit before use.
●Do not use this product indoors with IGT inserts designed for outdoor use.
●When replacing or refueling the gas cartridges of burners or stoves, ensure there is no fire nearby.
●For repairs, please contact the retailer where you purchased the product or Snow Peak user service.
●When you ask for repair, please make sure that the product is dry and clean.
●Please attach a memo or some kind of tag indicating the needed repair and also please write details of when and how the damaged occurred.
●Shipping cost and repair fee for the repair as follows.
1. Within warranty: Return shipping cost and repair fee will be covered by Snow Peak
2. Outside warranty: Return shipping cost and repair fee will be covered by the user.
Repair
Snow Peak USA, Inc.
404 NW 23rd Ave., Portland, OR 97210, USA
Tel: +1-503-697-3330 IG: @snowpeakusa
www.snowpeak.com
Snow Peak, Inc.
456, Nakanohara, Sanjo-shi Niigata 955-0147 Japan
Tel: +81
256-46-5858 Fax: +81
256-46-5860
www.snowpeak.co.jp
Extension IGT
CK-090
Instruction Manual : Ver 1.00
/
