300 mm shaft
300 mm shaft screw
hole
300 mm shaft
screw
Crankshaft
Hanger
Hanger nut
Crankshaft screw
Knurled nut
CK-300 clamp
(sold separately)
300 mm
shaft
Crankshaft
Clamp
screw hole
300 mm shaft
Knurled nut
Turn clockwise
to tighten
Lightly tighten the knurled nut until it
comes to the root of the threaded portion.
Table Top Architect Lantern Hanger
CK-302
Contents (Name of the Parts) Specifications
Safety Precautions: Before use, please read thoroughly to ensure safety and avoid accidents.
CAUTION: Misuse could result in injury to the user and/or damage to property.
Maintenance and disposal
Warranty
Repair
DANGER: Misuse could easily result in a serious accident or death.
DANGER: Misuse could easily result in a serious accident or death.
<Lantern Hanger> Crankshaft x 1, 300 mm shaft x 1, Instruction Manual
(this document) x 1
CAUTION
Be careful not to cut your hand on the edge of the threaded portion.
Instructions for Use
This product is designed to be attached to the CK-300 clamp (sold separately). Before assembling, please read the CK-300 clamp instruction manual carefully.
Thank you for purchasing this Snow Peak Product. This is a lantern hanger to be used specifically with LED lanterns of the table top architect (TTA) series. This
product is intended for hanging an LED lantern and illuminating a table from above by attaching it to an optional clamp and fixing it to the table. Do not use it for any
other purposes. In order to ensure your safety when using this product, please read these instructions carefully before use. Please be sure to keep this document for
future reference. If you find anything in the instruction manual that is difficult to understand, or if you find any product defects, stop using it immediately and contact the
dealer where you purchased the product, or Snow Peak Customer Service.
Material(s) Stainless steel, rubber material
Size 116 mm (L) × 26 mm (W) × 713 mm (H)/4.56" (L) ×
1.02" (W) × 28.07" (H)
Weight 310 g/0.68 lb
Maximum hanging load 500 g/1.10 lb
Before using the product, check each part for abnormalities. If there are abnormalities, take the product to the dealer or Snow Peak Customer Service for
inspection or repair.
Do not install this product near heat sources such as a burner, oil stove, or grill. Doing so may lead the product to become hot, which may cause a burn, fire, or
product damage.
This lantern hanger can only be used with LED lanterns. Do not hang lanterns that use flames, such as a gas lantern. Using non-LED lanterns may cause a burn or fire.
Be careful not to cut your hand on the edge of the threaded portion.
After assembly, check for wobbling, and loose screws and clamp bolts. Also,
regularly check the screws and bolts for looseness during use. If this product
is used while it is wobbly or screws and bolts are loose, parts may fall off or
objects may fall, which may result in personal injury or product damage.
Do not use this product if it cannot be assembled as described in the
Instruction Manual due to deformation or rust. If this product is used for a long
period of time, it may become deformed or rust, which may prevent screws
from turning smoothly or cause the product to become unstable when
assembled. If you continue to use this product in such a state, it may fall apart
or parts may come off, which may result in personal injury or product damage.
Please note that this product becomes hot if used in a place exposed to
direct sunlight for a long period of time, particularly under scorching sun.
When using this product outdoors, use it in a place where it will not be
exposed to rain, such as under a tarp. If you leave this product wet with
rainwater for a long period of time, the screws and joints may rust, which may
lead to discoloration and sticking.
Do not assemble or disassemble this product when it is wet or with wet
hands. Otherwise, an injury may result.
The product should be assembled by a person who is capable of
understanding the Instruction Manual, has a sufficiently strong grip, and who
has the ability to assemble it correctly.
Do not remove the rubber cap attached to the edge of the lantern hanger. Be
careful not to lose it. If you remove the rubber cap, you may be injured by the
edge of the lantern hanger.
Do not forcefully pull the lantern hanger. Doing so may lead the lantern
hanger to spring back, causing an injury.
This product can only be used to hang an LED lantern weighing up to
500 g/1.10 lb. If you hang a lantern heavier than that, the lantern may fall,
resulting in personal injury or product damage.
While this product is attached, do not attempt to adjust the attachment
position, or move it. If you loosen the clamp while the product is being
assembled, the product may fall off, which may result in personal injury or
product damage.
When carrying this product, store it while protecting the screws using a soft
cloth or other material. If this product is stored with the screws exposed, they
may come into contact with other products, causing the screws to be
damaged.
Use this product on a flat and stable surface. If it is used on an angled or
unstable surface, the product may fall, resulting in personal injury or product
damage. Also, read the instruction manual for the table, and use this product
correctly.
The knurled nut and hanger nut can be removed. Periodically check that they
are not loose; otherwise, they may be lost.
After assembling this product, check that it does not easily come off the table.
This product is not intended for permanent use. Clean this product
immediately after use, and keep it out of the reach of children.
If professional repairs are required, please contact the retailer where you purchased the product or Snow Peak Customer Service.
When you request repairs, please make sure that the product is dry and clean.
Please attach a memo or a tag indicating the necessary repair and please write details of how and when the damage occurred.
Transportation and repair costs are determined as follows.
1. Within warranty: The transportation cost (both ways) and repair cost
will be covered by Snow Peak.
2. Outside warranty: The transportation cost (both ways) and repair cost
will be covered by the customer.
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find any product defects, please contact the retailer
where you purchased the product or Snow Peak Customer Service. If there are apparent defects in the product's manufacturing, the defective product will be
repaired or exchanged free of charge. In other cases, Snow Peak will repair the product for an appropriate fee. The decision to repair or replace the product will be
at our discretion. Snow Peak will not repair the product for any damage that occurred due to the following:
1. Material deterioration caused by age
2.
Damage caused by modifications or rough handling
3. Damage caused by inappropriate use not
mentioned in the instruction manual
4. Damage caused by unexpected accidents
5. Any damage other than defects in the
manufacturing process
6. Damage caused by dust or rust
7. Damage and defects caused by dismantling
the product
8. Damage and defects caused by dropping,
jolting or other shocks
9. Deterioration or failure of parts due to friction
10.
Damage caused by the use of the product in
combination with another manufacturer's products
Before using a product that has been in storage for a long time, check each part for abnormalities. If there are abnormalities, take the product to the retailer or
contact Snow Peak Customer Service for inspection or repair.
After use, follow the procedure described below to appropriately clean and store the product. Not cleaning dirt or moisture off the product may cause rust to form.
After use, disassemble the product and clean it using a dry cloth.
If the product is wet, disassemble it, wipe it, and dry it well.
If salt, seasonings, or other substances are adhered to the product, wipe them off thoroughly using a tightly wrung cloth and allow it to dry thoroughly.
If you use this product in a location exposed to sea breezes such as a beach, disassemble it, wipe it thoroughly using a tightly wrung cloth, and dry it well.
When disposing of this product, follow the rules of the local government of your area.
Move the CK-300 clamp unit to make sure that it does not wobble.
Then, screw the 300 mm shaft clockwise into the screw hole of the CK-300
clamp, and tighten it all the way.
Check that the 300 mm shaft is not loose, and then turn the threaded portion of
the crankshaft clockwise and tightly fit it into the screw hole of the 300 mm
shaft. At this time, lightly tighten the knurled nut until it is at the root position of
the threaded portion. Do not open the lantern hanger arm when turning the
crankshaft as doing so is dangerous.
After tightening the threaded portion of the crank shaft all the way, turn the
crank shaft in the opposite direction to set it to the desired position of the
lantern hanger. After finalizing the position of the lantern hanger, rotate the
knurled nut clockwise and tighten it as much as possible.
Open the lantern hanger arm and hook a lantern to it.
To remove it, implement the attachment procedure in reverse.
Instruction Manual: Ver 1.00
Snow Peak Customer Service
(9:00-17:00)
+1 503-697-3330
Email: inf[email protected]
If you have any questions or concerns,
please contact your retailer or Snow
Peak customer service.
Use this product in the form shown on the left. If
you rearrange this product into another form or
combine it with another company's product, it may
become unstable and fall off, which may result in
personal injury or product damage.
CAUTION
Keep an eye on small children if they are nearby. If children play with this product, it may result in unexpected accidents.
Be sure to use the CK-300 clamp (sold separately) to fix this product to a table. If you use other means, the product may fall, resulting in personal injury or
product damage.
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. inf[email protected] / www.snowpeak.com
-
1
-
2
