ES-080
Ver 1.10
Instruction Manual Ver 1.10
How to turn on: push the switch once
1. Push the switch when it’s in the off position.
2. Confirm lighting. (At this time, the brightness will be dim.)
How to adjust the brightness. Continue to hold the switch down
1. Continue to hold the switch down in the on position.
2. Holding the switch to increase brightness gradually.
3. Stop holding when the desired brightness is reached.
* Brightness control works only by dimming. when you hold the switch down, the brightness
is maximized.
Once the brightness is maximized, the indicator flashes.
When you hold the switch down again, the brightness will drop slowly.
How to turn off the light. Push the switch once
1. Push the switch once when it’s in the on position
2. Confirm lighting.
*When you unpack the package, check for the following accessories.
(1) When using a charging stand
Please place it on the charging stand—the indicator
lights for 5 seconds when the battery is charging
without any problem.
* Please place the convex part on the bottom of the
main unit and the concave part on the charging
stand. If the product is placed incorrectly, the power
may flow back and damage the product.
(2) How to use the rear USB-C connector
Charge this product by inputting a power supply that
complies with the specified USB standard to the
USB-C Connector on the back of the main unit.
Open the rear silicon connector cover. Connect the
cable to a mobile battery and plug the USB-C jack
into the rear connector—the indicator lights for 5
seconds when the battery is charging without any
problem.
Do not use the USB-C connector near water
sources. Always close the USB-C connector cover.
This product changes shape for easy hanging.
Handle
Shade
Lamp cover
Power switch
Indicator USB-C connector
Charging
stand
Front Back
Troubles Reason Action
Will not light
Light goes out
immediately after
turning it on
The product won’ t
charge
Batteries are dead.
Dead batteries
The terminal is dirty Wipe the terminals and charging stand clean
with a dry cloth.
Type-C Connector, Please use an external power
supply that complies with USB Type-C Current 3A.
This product does not support USB-PD.
Problem with batteries Confirm the batteries are installed correctly.
All the indicators are
flashing
There is poor contact
with the power supply
Disconnect from the power supply and
charge the battery again.
After trying all of the
above, nothing works.
The light may be
damaged.
Stop use immediately and call Snow Peak
customer service or your local Snow Peak retailer.
Inadequate supply
Place the unit on a charging stand or connect
the power to the rear USB-C. Ensure the
charge indicator lights up for 5 seconds.
Place the unit on a charging stand or connect
the power to the rear USB-C. Ensure the
charge indicator lights up for 5 seconds.
Motion Flow Chart
* Please make sure to cover the shade part on the bottom of the main unit (or the lamp cover)
to undo. If you lift the product while it is unstable, the product may rotate and hit something,
potentially resulting in permanent damage to the product.
* Do not place the product on the ground or on a table while it is in the hanging shape, as this
could result in permanent damage to the product.
* Turn off the light when hanging this product. You will be looking directly at the LED light, and it
may result in blindness or injury.
Charging stand
An AC adapter is required to connect a charging stand to a home AC power source. Please
use an AC adapter with an output of 5V-2.0A.
Type-C Connector
Please use an external power supply that complies with USB Type-C Current 3A. This product
does not support USB-PD.
Slowly push down the shade part
horizontally with both hands and cover the
bottom of the main unit.
Lift the shade parts horizontally with both
hands.
Hold and lift the handle while slowly
rotating the main unit by 180 degrees.
Use the indent on the handle to hang it on
the hook.
Name of parts
Specifications
How to use About the external power supply
For stains on the body of light, wipe it with a moist cloth. Use a dry cloth or cotton swab to wipe
off the battery terminals when dirty. If the body gets wet, wipe the moisture off with a dry and
soft cloth completely and before storing. If moisture gets into the USB connection or inside the
body, stop using light immediately. Contact Snow Peak Customer Service or a retailer for repair
or to confirm safe operation.
The specifications of Snow Peak products are based on field testing and quality control to ensure
the correct function and longevity of every product. If apparent defects in the product's manufac-
turing are found, the defective product will be repaired or exchanged free of charge. However,
damages, as follows, are not covered under warranty.
1. Material deterioration caused by age.
2. Damage caused by modifications or rough handling.
3. Damage caused by improper use not following the instruction manual.
4. Damage caused by unexpected accidents.
5. Damage not caused by defects in the manufacturing process.
6. Damage caused by dust or rust.
7. Damage or defects caused when dismantling the product.
8. Damage and defects caused by dropping or other shocks to the product.
9. Deterioration or failure of parts due to friction.
10. Damage caused by the use of the product in combination with other maker’s products.
Please regularly care for your light.
Troubleshooting
Warranty
●If a professional repair is necessary, please contact the dealer where the product was sold or
Snow Peak Customer Service.
●Please dry and clean the product before sending it for repair.
●Please stick a memo onto the damaged area of the product. In the memo, include details
explaining the circumstances that led to the damage.
●The cost of repair will be determined as follows:
1If the damage is subject to warranty, transportation cost both ways and repair cost will be
covered by Snow Peak.
2If the damage is not subject to warranty, transportation cost both ways and repair cost will be
covered by the customer.
Regarding Repair
Charging method
How to use
How to hang this product
Safety Precautions
Thank you for purchase of this Snow Peak product. This LED lantern offers a warm light for
home and camp use. Please read the instructions carefully before use and keep for true
reference. Please confirm you have received all the necessary components. Assemble the light
in a safe location and make sure you fully understand the function of the LED Light before use. If
product is damaged upon purchase please stop using it immediately and contact Snow Peak
customer service or the Snow Peak dealer where you purchased your new light.
ES-080
HOME & CAMP Lantern
WARNING / Misuse could result in serious injury or death to the user.
● Do not use this product where it may get soaked in water. This could result in electric shock
or permanent damage to the product.
● Do not use the product covered with cloth, as this may result in fire or electric shock.
● Always carry an extra power source, such as batteries.
● If there is liquid leaking from the rechargeable battery, do not allow the liquid to contact your
skin or eyes. In case of contact, rinse well with water and consult a doctor.
● Do not bend or bundle the power cable to prevent malfunction.
● Do not use this product under high temperatures outside the suggested ranges, as this may
cause leaking of batteries, overheating, or even fire.
● Do not use the product near any heat sources, as this may result in overheating or fire.
● Do not charge this product near a water source. It may result in overheating, fire, or electric
shock.
● Only use a power supply with an output of 5V-A for charging. Using other outputs increases
the risk of overheating or fire.
DANGER / Misuse could easily result in a serious accident or death.
● Keep out of the reach of children. It could result in injury or choking if parts are swallowed
mistakenly.
● Do not touch any metal items to the connection area or terminals, as overheating, fire or
electric shock may occur.
● Do not dismantle or modify. Improper handling or modifications may result in electric shock.
● Do not touch connection areas with wet hands. Doing so may result in overheating, fire, or
electric shock.
● Parents must supervise children using this product. Unsupervised children could damage
the product, which could result in injury or electric shock.
CAUTION / Misuse could result in injury to the user and/or damage to property.
● Dropping the light may cause unexpected failure during regular use. Please thoroughly
examine the product for damage.
● Avoid looking directly at the light source as it may hurt your eyes.
● Do not hang the light while the power cable is connected. The cable may get caught and
fall or be damaged.
● Do not place directly on the ground, as this may cause the charging terminal to malfunction.
● Set includes: main unit x 1, charging stand x 1, instruction manual x 1
● Material: ABS Resin, PC Resin, stainless steel, silicone resin
● This product uses a lithium polymer rechargeable battery
● Maximum light time: 4 hours (when maximum light quantity is used) and 23 hours (when 100
lm is used)
● Safe operating temperature: when unplugged -10℃~35℃/14℉~95℉,
while charging 0℃~35℃/32℉~95℉, while storing -10℃~35℃/14℉~95℉
● Maximum illumination: 400lm
● Drip-proof: IPX4
● Color of light: Warm White 3000K
● Country of origin: China
● Size: φ 124 x 250 mm (Main unit Only), φ 130 x 270 mm (Including the charging stand)
● Weight: 500g (Main unit), 250g (Charing stand)
MADE IN CHINA
Charging stand, Please use an AC adapter
with an output of 5V-2.0A. An AC adapter with
an output of 5V-2.0A is required to connect a
charging stand to a home AC power source.
Snow Peak, Inc.
456, Nakanohara, Sanjo-Shi, Niigata 955-0147 Japan
Tel. +81 256-46-5858 Fax. +81 256-46-5860
www.snowpeak.co.jp
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 Instagram. @snowpeakusa
www.snowpeak.com Email. [email protected]
/
