Snow Peak ST-021 取扱説明書

タイプ
取扱説明書
ST-021
Ver 1.00
Body Leg Parts Base Plate Base Plate
Carrying Case
Triangular Plate
Bridge
Leg Parts
Upper Plate This part will be on
the top side when it is folded.
Lower PlateThis part will be on the bottom side when it is folded.
Handle
Leg Parts
Body
Mounting
Groove
Prong
Prong
Make sure that the protrusions
come out of the holes in the leg parts.
Hold the bridge and lift both
of the leg parts.
Hook for the Base Plate
Base Plate
Leg parts
Body
Mounting Groove
Prong
Put the body on the ground.
Ash
Upper Plate
Lower Plate (There are long and rails at both ends.)
Triangular Plate
Cross Section
Carrying Case
Body, Leg Parts, Base Plate,
Fold it so that the top plate passes
over the bottom plate.
Slits
Slits Warping and
Deformation around Slits
Pack & Carry Fireplace (SR)
ST-021
Instruction Manual : Ver 1.00
Specifications
Set Contents (Name of the Parts)
●Set Contents : Body, Leg Parts x 2, Base Plate, Carrying Case Material : Body, Leg Parts, Base Plate / Stainless
Steel, Carrying Case / Polyester ● Body Size : 480 x 265 x 385 (h) mm (18.9”x 10.4”x 15.2”) ● Storage Size : 455 x 265
x 60 (h) mm (17.9” x 10.4”x2.4”) ● Weight : 4.3 kg (9.49lbs) (excluding Carrying Case)
Thank you very much for purchasing a Snow Peak product. This product is a portable fireplace designed for camping. To use this product safely and correctly, please
read these instructions carefully. After reading these instructions, keep this manual in a safe place for future reference. If you find anything in the instruction manual that
is difficult to understand, or if you find a product defect, stop use immediately and contact the dealers where you purchased the product or Snow Peak Customer Service.
Before use: please read these instructions thoroughly to ensure safety and avoid accidents.
DANGER / Misuse could easily result in a serious accident or death.
●This product is for outdoor use only. Do not use the product inside a house, tent, car, or confined space. Please use it outdoors in an area with adequate ventilation.
WARNING / Improper use may result in death or serious injury.
CAUTION / Misuse could result in injury to the user and/or property damage
●Please ensure the body is cool before cleaning. Also, do not subject the product to rapid temperature changes such as spraying with water while the product is hot.
Rapid temperature changes may cause warping or damage. ●Be sure to use both hands when installing or storing the product. Please note that improper handling
may cause injury or damage to the product. ●The product may change color or be slightly distorted, but this does not affect the quality or performance. ●This product
is made of stainless steel; it may rust depending on the operating conditions and surrounding environment. ●Please check with your local government or administra-
tor when you make a fire in public places such as parks, riverbeds, and campsites. Do not use this product in areas where the use of fire or barbeques is prohibited.
●Please do not use this product for incinerating waste, as this may violate local waste management laws.
●Before using the product, check each part for abnormalities. If there are abnormalities, take the product for inspection or repair by the dealer where the product was
sold or Snow Peak Customer Service. ●Before use, ensure there are no flammable or heat-sensitive materials near the product. Additionally, do not use this product
near flammable objects such as a tent or a tarp. Do not use it in areas where wildfire danger is high, such as on dry grass or near dried debris. ●Always use the
attached base plate. Do not use the product in areas where the base plate will sit on large stones or tall grass. If the base plate comes off, the fireplace will be unstable
and may tip over, potentially damaging the main body or causing a fire. ●Avoid using this product on sloped or unstable areas as it may tip over. Once set up is
complete, ensure all the legs are touching the ground and no parts are rattling before beginning use. ●It is very dangerous to use this product in strong winds. If the
wind becomes strong during use, please extinguish the fire and discontinue use. ●Do not use a burner or gas lantern near the product. The fuel canister may overheat
and explode. ●Please note that this product may become extremely hot during use. Please pay close attention to the weather and surrounding conditions. It is very
dangerous if small children play near the fire. ●It is dangerous to move this product during use. When you move the fireplace, make sure the fire is completely out, and
the main body is cold. ●Please ensure the fire is completely out before going to bed. A smoldering fire may cause an unexpected accident. ●Do not put too much
firewood or charcoal into the product. The flames may overflow and cause a fire or burns.
Bonfire (takibi) can be very dangerous if not handled properly. This product will not avoid or mitigate fire-related hazards. This product is safe, provided
you follow the instructions and use the product in a responsible manner. Please read and understand this manual thoroughly before use.
Maintenance
●When washing the product, be sure to disassemble it and wash each part separately. If you wash it in the assembled state, the stand will be unstable and may tip
over, causing damage to the body. ●When cleaning the product, use a soft brush as an abrasive scrubber may damage the surface. After washing, wipe off excess
water with a cloth. Set the product to dry in a well-ventilated, shaded area. ●Store in a dry place with no moisture. ●If the case gets dirty, wipe it off with a cloth soaked
in neutral detergent. Do not use chemicals such as thinners or benzine. ●When using a product that has not been used for a long time, please contact our User Service
for inspection.
MADE IN KOREA
The specifications of Snow Peak products are based on field testing and quality control to ensure the proper function and longevity of every product. If apparent defects
in the manufacturing of the product are found, the defective product will be repaired or exchanged free of charge. Damages, as follows, are not covered under warranty.
1. Material deterioration caused by age. / 2. Damage caused by modifications or rough handling. / 3. Damage caused by improper use not adhering to the instruction
manual. / 4. Damage caused by unexpected accidents. / 5. Damage not caused by defects in the manufacturing process. / 6. Damage caused by dust or rust. / 7.
Damage or defects caused when dismantling the product. / 8. Damage and defects caused by dropping or other shocks to the product. / 9. Deterioration or failure of
parts due to friction. / 10. Damage caused by the use of the product in combination with other maker's products.
Warranty
Attach the leg parts to the body.
Place the folded product on the ground with the triangular plate facing up, and
mount it so that the prong fits into the leg parts' mounting groove, as shown in
the figure. Ensure the four prongs are secured to the end of the mounting
groove on the outside of the leg parts. If the mounting is insufficient, it will be
impossible to assemble.
Lift the leg parts and raise the body.
Hold the bridge of both leg parts, and lift the body forcefully to prevent the prong
from detaching. The leg parts stand up, and the body is assembled.
* If the horizontal part of the body isn't correctly attached to the leg parts, it will not
stand up properly. In this case, place everything on the ground again, shift the
position of the leg parts vertically and lift it again.
Mount the base plate.
Pass the base plate over the first beam at the bottom of the leg parts, and
pass the hook for the base plate located on the first beam of the leg part
through both holes on the base plate. Then, open the leg part and firmly
attach it to the hook for the base plate.
* Be sure to attach the base plate.
* Ensure the hook of the leg part is completely inserted into the hole of the base
plate. If the base plate detaches due to improper mounting, the product will not
stand on its own and may fall over.
Remove the base plate.
Pull the leg part inwards, remove
the base plate from the hook on
the leg part, and remove the base
plate over the top of the first beam.
Hold the bridge of both leg parts, then slowly lower the main body while spread-
ing the leg parts. Remove the leg parts one-by-one from the main body by
pushing both leg parts further apart while holding the main body steady.
* The bridge after use is dirty with soot. Please wear gloves when you hold the
bridge.
Throw away the ash.
Hold the body and tilt it to throw
away the ash.
Please fold the body and each part.
Push up the body's triangular plate towards the center, push up both plates so
that the upper plate passes over the lower plate, and fold. After that, please
lower the triangular plate.
Put each part in the carrying case.
Stack the leg parts so they alternate as shown in the figure, and put each part
in the carrying case.
Usage How to Store
CAUTION / This section contains important
precautions for using this product. Please
read them carefully before use.
The upper and lower plates of this product
come with slits that prevent warping and
deformation. The area around the slits may
swell due to heat, but this will not impact
product functionality.
●If a professional repair is necessary, please contact the dealer where the product was sold or Snow Peak Customer Service.
●Please dry and clean the product before sending it for repair. ●Please stick a memo onto the damaged area of the product. In
the memo, include details explaining the circumstances that led to the damage. ●The cost of repair will be determined as follows:
1 If the damage is subject to warranty, transportation cost (both ways) and repair cost will be covered by Snow Peak. / 2 If the
damage is not subject to warranty, transportation cost (both ways) and repair cost will be covered by the customer.
Regarding Repair
  • Page 1 1
  • Page 2 2

Snow Peak ST-021 取扱説明書

タイプ
取扱説明書

他の言語で