Sony HVL-F56AM ユーザーマニュアル

2-687-455-33 (1)

HVL-F56AM

Operating Instructions

Flash

2

English

Before operating the product, please read this manual thoroughly and

retain it for future reference.

WARNING

To reduce fire or shock hazard, do not expose the unit to rain or moisture.

Tape over lithium battery contacts to avoid short-circuit when disposing of

batteries, and follow local regulations for battery disposal.

Keep batteries or things that could be swallowed away from young

children. Contact a doctor immediately if an object is swallowed.

Immediately remove the batteries and discontinue use if...

• the product is dropped or subjected to an impact in which the interior is

exposed.

• the product emits a strange smell, heat, or smoke.

Do not disassemble. Electric shock may occur if a high voltage circuit

inside the product is touched.

IMPORTANT SAFETY

INSTRUCTIONS

When using your photographic equipment, basic safety

precautions should always be followed, including the

following:

Read and understand all instructions before using.

Close supervision is necessary when any appliance is used

by or near children. Do not leave appliance unattended

while in use.

Care must be taken as burns can occur from touching hot

parts.

3

Do not operate appliance with a damaged cord or if the

appliance has been dropped or damaged- until it has been

examined by a qualified serviceman.

Let appliance cool completely before putting away. Loop

cord loosely around appliance when storing.

To reduce the risk of electric shock, do not immerse this

appliance in water or other liquids.

To reduce the risk of electric shock, do not disassemble this

appliance, but take it to a qualified serviceman when

service or repair work is required. Incorrect reassembly can

cause electric shock when the appliance is used

subsequently.

The use of an accessory attachment not recommended by

the manufacturer may cause a risk of fire, electric shock, or

injury to persons.

Batteries may become hot or explode due to improper use.

Use only the batteries specified in this instruction manual.

Do not install the batteries with the polarity (+/-) reversed.

Do not subject batteries to fire or high temperatures.

Do not attempt to recharge (except for rechargeable

batteries), short or disassemble.

Do not mix, batteries of different types, brands or ages.

SAVE THESE

INSTRUCTIONS

CAUTION

Do not touch the flashtube during operation, it may become hot

when the flash fires.

4

For customers in Europe

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European

countries with separate collection systems)

This symbol on the product or on its packaging indicates that

this product shall not be treated as household waste. Instead

it shall be handed over to the applicable collection point for

the recycling of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment

and human health, which could otherwise be caused by

inappropriate waste handling of this product. The recycling

of materials will help to conserve natural resources. For more

detailed information about recycling of this product, please

contact your local Civic Office, your household waste

disposal service or the shop where you purchased the

product.

For the customers in the U.S.A.

CAUTION

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one

or more of following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

5

Table of contents

Features .................................... 6

Name of parts .......................... 7

Control panel ........................... 8

Data panel ................................ 9

Preparations

Inserting batteries ................. 10

Attachment and removal

of the flash ............................. 12

Auto power ON/OFF .......... 13

Basics

Program auto flash

(The basics) ............................ 14

Recording modes .................. 17

Apprications

Zoom flash coverage ............ 19

Test-flash/Modeling flash ... 22

Bounce flash .......................... 24

Close-up photography

(downward bounce) ............. 27

Data panel illuminator ......... 28

AF illuminator ....................... 29

Mode and select buttons ...... 30

Manual flash (M) .................. 32

High-speed sync (HSS) ........ 35

Wireless flash mode (WL).... 37

Connecting camera and flash

by cable................................... 43

Setting power level (LEVEL)

................................................. 44

Multiple flash (MULTI) ........ 46

Reset to default settings ....... 51

Custom setting ...................... 52

Additional

Information

Accessories............................. 55

Notes on use .......................... 57

Maintenance .......................... 58

Specifications ......................... 59

6

Before use

For details, refer to the operating instructions supplied with your camera.

This flash is not dust-proof, splash-proof or waterproof.

Do not place this flash in the following locations

Regardless of whether this unit is in use or in storage, do not place it in any

of the following locations. Doing so may lead to a malfunction.

• Placing this flash in locations subject to direct sunlight such as on

dashboards or near a heater may cause this unit to deform or

malfunction.

• Locations with excessive vibration

• Locations with strong electromagnetism

• Locations with excessive sand

In locations such as the seashore and other sandy areas or where dust

clouds occur, protect the unit from sand and dust.

This may lead to a malfunction.

Features

• The HVL-F56AM is a compact, clip-on flash that provides a large flash

output with a guide number 56 (85 mm position, ISO 100 · m).

• The built-in wide panel expands flash coverage to a focal length of 17

mm.

• The HVL-F56AM assures highly reliable ADI (Advanced Distance

Integration) flash metering when used in combination with compatible

lenses.

• The HVL-F56AM supports wireless high-speed sync photography.

• The flash head tilts 90° upward, 180° left and 90° right to bounce flash

(with lock function) and 10° downward for close-up photography.

* This function may not be available on some camera models.

7

Name of parts

Built-in wide panel

(21)

Flashtube

AF illuminator

(29)

Wireless control-

signal receiver (37)

Bounce indicator

(24)

Data panel (9)

Control panel (8)

Terminal cap

Mounting-foot-

release button (12)

Mounting foot

Bounce lock-

release button (24)

Battery-chamber

door (10)

Remove the protective sheet from the front

of the AF illuminator before use.

Inside terminal

• Accessory terminal (43)

• External-power terminal (56)

8

Control panel

SELECT button

– button

MODE button

Data-panel

illuminator

(28)

Flash ON/OFF button

(13)

Flash-ready lamp (15)

ZOOM (flash-coverage)

selection button (20)

Test-flash mode

selection/Hold switch

(22)

Test-flash

button/

Modeling-flash

button (23)

+ button

9

Data panel

Wireless controller indicator*

High-speed-sync

indicator (35)

Wireless flash

indicator (40-42)

Flash-OK indicator

(15)

TTL indicator (32)

Manual-flash-

control

indicator (32)

Multiple-flash

indicator (46)

Custom

indicator (52)

Ratio-flash indicator*

* This indicator is

displayed, but this

function is not

available.

Power-level

indicator (44)

Manual-ZOOM

indicator (20)

Zoom (19, 20)/Multiple-flash-

repetition display (48)

mm indicator (19)

TIMES indicator

(48)

Bounce

indicator (24)

Low-battery

indicator (11)

ft/m indicator

(53)

Flash ON/OFF indicators

(14)

Flash-range (16)/Multiple-flash-

frequency display (47)

Hz indicator (47)

Flash-range-warning indicators (16)

On this page, all indicators are displayed for explanatory purposes.

10

Inserting batteries

The HVL-F56AM may be powered by :

*Batteries are not supplied.

• Four AA-size alkaline batteries

• Four AA-size lithium batteries

• Four AA-size rechargeable nickel-metal hydride (Ni-MH) batteries

Always ensure that rechargeable nickel-metal hydride batteries are

charged in the specified charger unit.

1 Open the battery-chamber door as shown.

2 Insert the batteries in the battery chamber as in the

diagram.

3 Close the battery-chamber door.

• Follow the reverse steps when opening the battery-chamber door.

• The indicator appears on the data panel. If it does not appear, press

the flash ON/OFF button.

11

Preparations

Checking Batteries

The indicator on the data panel blinks when the batteries are low.

blinking

Changing the batteries is

recommended. The flash can still be

used in this state if (Flash-ready

lamp) on the rear of the unit is lit.

Only blinking

Flash cannot be used.

Insert new batteries.

• If nothing appears when the flash ON/OFF button is pressed, check the

orientation of the batteries.

12

Attachment and removal of the

flash

Attaching the flash to the camera

Push the mounting foot firmly onto the camera until it

stops.

• The flash is locked in place automatically.

• If the built-in flash in the camera is protruding, lower it before attaching

the flash unit.

Removing the flash from the camera

While pressing the mounting-foot release button 1,

remove the flash 2.

1

2

13

Preparations

Auto power ON/OFF

Press the flash ON/OFF button on the back side of the

flash.

Power of the flash turns it on.

When the flash is switched on, will

appear on the data panel indicator.

If you press the flash ON/OFF button while

the flash is turned on, the flash switches off

and appears on the data panel

indicator.

• disappears after 8 seconds.

Auto power off

When the camera or flash is not used for four minutes, power switches off

and data panel indicators disappear automatically to save the batteries.

• In wireless flash photography (p. 37), data panel indicators disappear

after 60 minutes.

• The customized settings enable you to disable auto power off or change

the auto power off time (p. 53).

14

Program auto flash (The basics)

1 Select the P mode on the camera.

2 Press the flash ON/OFF button to display or

.

• and appear with Autoflash. Only appears with

Fill-flash.

3 Press the shutter button partway down and make sure

that the subject is within the flash range.

• See page 16 for details on the flash range.

Basics

15

4 When the flash is charged, press the shutter button to

take a photo.

• The flash is charged when indicators on the rear of the unit and in

the camera viewfinder are both lit.

When the correct exposure has been obtained for the photo just taken,

is displayed in the data panel for approximately four seconds.

• The photo will be under-exposed if taken before charging is complete.

• Press the shutter button after making sure that charging is complete

when using the flash with the self-timer.

• Either Autoflash or Fill-flash is selected, depending on your camera. For

details, refer to the operating instructions of your camera.

• If your camera has AUTO mode or Scene Selection mode, they are dealt

with here as program auto.

Continued on the next page

16

Flash range

Press the shutter button partway down.

The flash range for the proper exposure is displayed on the data panel.

Make sure that the subject is within this range and then take the photo.

The range that can be displayed on the data panel is from 1.5 m to 28 m

(0.7 m to 28 m for downward bounce; see p. 27). When the distance is

beyond this range, or is lit on either side of the viewfinder.

Proper exposure is obtained at less than 1.5

m.

Proper exposure is obtained from 8 m to 28

m or more.

• The flash range is not shown when using flash bounce above and to the

left or right, with wireless flash, or when off-camera cables are used.

• When photographing beyond the lower limit of the flash range, the

photo may be over-exposed despite being displayed, or the bottom

of the picture may darken. Always photograph within the indicated

flash range.

Basics

17

Recording modes

Aperture priority flash photography (A)

1 Select the A mode on the camera.

2 Press the flash ON/OFF button to display .

• Fill-flash is selected.

3 Set the aperture and focus the subject.

• Reduce the aperture (i.e. increase the f-stop) to reduce the flash

range, or open the aperture (i.e. reduce the f-stop) to increase the

flash range.

• The shutter speed is automatically set.

4 Press the shutter button when charging is complete.

Continued on the next page

18

Shutter speed priority flash

photography (S)

1 Select the S mode on the camera.

2 Press the flash ON/OFF button to display .

• Fill-flash is selected.

3 Set the shutter speed, and focus the subject.

4 Press the shutter button when charging is complete.

Manual exposure mode flash

photography (M)

1 Select the M mode on the camera.

2 Press the flash ON/OFF button to display .

• Fill-flash is selected.

3 Set the aperture and shutter speed, and focus the

subject.

• Reduce the aperture (i.e. increase the f-stop) to reduce the flash

range, or open the aperture (i.e. reduce the f-stop) to increase the

flash range.

4 Press the shutter button when charging is complete.

19

Applications

Zoom flash coverage

Auto zoom

This flash automatically switches zoom coverage to cover a range of focal

lengths from 24 mm to 85 mm when photographing (auto zoom).

Normally, you do not need to switch the zoom coverage manually.

• Press the shutter button partway down to display the zoom coverage set

automatically.

• Auto zoom coverage is set as follows:

• When a lens having a focal length of less than 24 mm is used with auto

zoom, “24 mm” blinks. Use of the built-in wide panel (p. 21) is

recommended in this case to prevent darkening at the periphery of the

image.

24 mm focal length 85 mm focal length

Focal length in use Coverage

24 mm - 27 mm 24 mm

28 mm - 34 mm 28 mm

35 mm - 49 mm 35 mm

50 mm - 69 mm 50 mm

70 mm - 84 mm 70 mm

85 mm or more 85 mm

Continued on the next page

20

Manual zoom

You can manually set the zoom coverage regardless of the focal length of

the lens in use.

Press the ZOOM button to display the desired zoom

coverage.

• Zoom coverage is changed in the following order.

• When zoom is set manually, “M.ZOOM” is displayed above zoom

coverage.

• If the zoom coverage is set to less than the focal length of the lens in use,

the periphery of the screen darkens.

Auto zoom t 24mm t 28mm t 35mm t 50mm t 70mm t 85mm

ページが読み込まれています...

Sony HVL-F56AM ユーザーマニュアル

Sony HVL-F56AM ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント