Motorola HX1 - Endeavor - Headset クイックスタートガイド

Quick Start Guide

ᖿ䗳Փ⫼᠟ݠ

MOTOROLA

ENDEAVOR HX1

1

your headset

charge it

pair & connect

enable stealth modebena

put it on

turn on & off

battery check

calls

status indicators

tips & tricks

problems?

Safety & General Information

FCC Notice to Users

European Union Directives

Conformance Statement

Contents

3

4

5

9

11

18

19

20

22

24

25

27

31

42

2

congratulations

Talk hands free where you never have before on the

MOTOROLA

ENDEAVOR

HX1 headset thanks to Motorola’s revolutionary CrystalTalk™ technology with

stealth mode, delivering an unmatched headset audio performance even in the

ﬁercest conditions.

First of all, reduce everyday background noise with the default CrystalTalk mode

which utilizes dual microphone noise cancellation technology.

Then, if background noise and wind reach extreme levels, switch on stealth

mode to activate true bone conduction and seal off all background noise from

your conversation so you know you’re being heard. As you speak, the stealth

mode sensor captures your vocal vibrations and seamlessly converts them to

speech so the listener hears your voice only.

3

your headset

Take a moment to familiarize yourself with your new ENDEAVOR HX1 Headset.

Earhook

Charging

Port

Call

Button

Volume

Buttons

Speaker and

Stealth

Mode

Sensor

Indicator

Light

Power

Switch

Warning

: DO NOT

apply pressure or squeeze the stealth mode sensor (small

rubber balloon) as it can damage the parts inside and will void the warranty.

Ear Loop

Stealth Mode

Button

4

charge it

You'll need to charge your speakerphone before you can use it. While charging,

the battery indicator light is red. It turns green when the battery is fully charged.

Note: Headset is not functional while charging.

Note: Your battery is designed to last the life of your product. It should only be

removed by a recycling facility. Any attempt to remove or replace your battery

will damage your headset.

5

pair & connect

Let’s get your headset paired and connected to your Bluetooth phone(s).

pair & connect ﬁrst phone

Turn off any Bluetooth devices previously paired with your headset.

Turn on the Bluetooth feature on your phone.

Put the headset on your ear (see “wear it” on page 14 for help).

Turn on your headset (see page 18 for help).

The indicator light becomes steadily lit in blue and you hear “ready to

pair”.

Follow voice prompts to connect your phone to your headset.

Note: When prompted for the passkey, enter 0000.

1

2

3

4

5

6

When your headset successfully pairs with your phone, you hear “pairing

complete”. When connected, you hear “phone 1 connected” and see the

indicator light rapidly ﬂash in blue and purple.

pair & connect second phone (optional)

Turn off first phone and any other Bluetooth devices previously paired

Turn your headset off (see “turn off” on page 18 for help).

Turn on the Bluetooth feature on your phone.

Put headset on your ear.

1

2

3

4

pair & connect

with your headset.

Turn on your headset.

The indicator light becomes steadily lit in blue and you hear “ready to

pair”.

5

7

pair & connect

Follow voice prompts to connect your phone to your headset.

When your headset successfully pairs with your phone, you hear “pairing

complete”. When connected, you hear “phone 1 connected” and see the

indicator light rapidly ﬂash in blue and purple.

To connect to both phones, simply turn on the ﬁrst phone while the second

phone is connected. When you hear “phone 2 connected”, your headset is

connected to both phones. The last paired phone (your second phone) is now

your primary phone (or “phone 1”) for voice dial functionality.

6

8

test your connection

Place the headset on your ear.

On one phone, dial a number and press the Call/Send key. Repeat for

the second phone.

If your phone and headset are successfully connected, you hear ringing on the

headset.

For daily use, make sure your headset is turned on, and your phone’s Bluetooth

feature is on. Your headset and phone will connect automatically.

1

2

pair & connect

9

enable stealth mode

Be sure you are always heard during calls with both CrystalTalk and stealth

modes:

CrystalTalk is the default mode and is always active to cancel out everyday

background noise.

Stealth mode can be activated when noise and wind reach extreme levels

to seal off all background noise.

turn stealth mode on & off

To ativate stealth mode, press the dedicated stealth mode button while dialing

a call, receiving a call, or while in a call.

To deactivate stealth mode, press the stealth mode button while in a call, or

turn off the headset.

•

10

enable stealth mode

A voice prompt (“stealth mode on” or “stealth mode off”) or tone always

conﬁrms change to stealth mode status.

Note: When using stealth mode, it is essential that the stealth mode sensor is

placed correctly and is in contact with the ear canal (see step 3 on page 15). It is

normal for the sound of your voice to be less “natural” in stealth mode.

11

choose an ear ﬁtting

Your headset comes with both loop- and spring-type ear ﬁttings.

To get the best headset performance, try out all the supplied ear ﬁttings to get a

good ﬁt. To change your ear ﬁtting:

put it on

Left

Ear

Spring

Right

Ear

Spring

Medium

Ear

Loop

Small

Ear

Loop

12

put it on

Lift loop up and slide it off the headset in an upward direction.

Slide new ﬁtting downward onto earpiece, then align and push

bottom into groove.

1

2

13

put it on

Position earhook for left or right ear.

3

For Right Ear For Left Ear

14

wear it

Grasp headset and bend spring or loop.

put it on

1

15

2

put it on

Insert headset earpiece into your ear canal.

Ensure stealth mode sensor is in contact with your ear

canal.

Stealth Mode Sensor

Ear Canal

3

16

put it on

4

Using Spring

Using Loop

Place spring or loop in bend of your ear.

17

put it on

Flex the earhook and loop it over your ear.

Tip

: For the best audio performance and comfort, position the ear cushion

ear into your canal and point the headset microphone towards your mouth.

5

18

turn on

Slide the Power switch to the on position (no red is shown under the switch).

The indicator light ﬂashes blue three times, then ﬂashes in blue and purple (if

connected with a device) or is steadily blue (if ready to be paired).

turn off

Slide the Power switch to the off position (red is shown under switch). The

indicator light ﬂashes three times then turns off.

turn on & off

Power

Switch

Indicator

Light

19

Press and hold both Volume buttons while not on a call.

To save battery power, turn off the headset when you don't use it for an

extended time.

battery check

Indicator light voice prompt talk time

red “

battery level is low

” less than 2 hours

yellow “

battery level is medium

”

green “

battery level is high

” more than 4.5 hours

between 2 to 4.5 hours

ページが読み込まれています...

Motorola HX1 - Endeavor - Headset クイックスタートガイド

Motorola HX1 - Endeavor - Headset クイックスタートガイド

他の言語で

関連論文

その他のドキュメント