Motorola H390 - Headset - In-ear ear-bud クイックスタートガイド

Quick Start Guide

Motorola H560

/ 快速使用手册

1

BEFORE YOU BEGIN

1 CHARGE

Your Headset's Battery

2 START BLUETOOTH FEATURE

Your Phone

3 PAIR

Your Headset

3 PAIR

CONTINUED

Your Phone

4 TEST AND USE

USING YOUR H560

TURNING HEADSET ON AND OFF

EARBUDS AND YOUR HEADSET

WEARING THE HEADSET

CHANGING FOR USE ON OTHER EAR

CHANGING VOLUME BUTTON ORIENTATION

QUICK BATTERY CHECK

MAKING CALLS

INDICATOR LIGHT

AUDIO TONES

TROUBLESHOOTING

European Union Directives Conformance Statement

Contents

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

18

19

22

2

BEFORE YOU BEGIN

Before using this product, read the Important Safety and Legal Information pamphlet and follow its

instructions.

Take a moment before you get started to familiarize yourself with your new H560

Headset.

Call

Button

Indicator

Light

Volume

Buttons

Ear

Speaker

Power

Switch

Microphone

3

Verify slide switch is in the off position (toward the charging port).

Plug the Motorola charger into the end of the headset.

The indicator light turns red or yellow when the battery is charging. It may take

up to 1 minute for the indicator light to turn on. When the headset’s battery is

fully charged (about 2 hours), the indicator light turns green.

Disconnect the charger.

1 CHARGE

Your Headset’s Battery

1

2

3

Note: Headset is not functional while charging.

Note: This product uses a lithium ion, rechargeable, non-replaceable battery. Under normal use, the

expected life of the rechargeable battery is approximately 400 charges.

4

Press (Menu) > Settings > Connection > Bluetooth Link > Setup.

Scroll to Power.

Select Change.

Scroll to On.

Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on

until you turn the feature off.

Note: These steps are for most Motorola phones. For other phones, see your phone’s

user’s guide.

2

START BLUETOOTH FEATURE

Your Phone

Your phone’s Bluetooth feature is off by default. To use your headset, you must turn

on the Bluetooth feature in your phone.

For most Motorola phones (at the main menu):

1

2

3

4

5

3 PAIR

Your Headset

Before you can use your headset, you must pair (link) it with your phone.

Step A - ENSURE HEADSET IS IN PAIRING MODE

Power on headset by sliding the Power switch towards the microphone to initiate

easy pairing. After a few moments, the indicator light will be steadily lit in blue to

indicate headset is in pairing mode.

Indicator Light

(steady blue for

pairing)

If the headset does not enter pairing mode, see TROUBLESHOOTING for help.

6

On your Motorola phone, press (Menu) > Settings > Connection > Bluetooth

Link > Handsfree > Look for Devices.

The phone lists Bluetooth devices it ﬁnds.

Select Motorola H560.

Select OK or Yes to pair your headset with your phone.

Enter the passkey: 0000

Select OK.

When your headset successfully pairs and connects with your phone, the

indicator light changes from steadily lit to ﬂashing blue and purple.

Note: These steps are for most Motorola phones. For other phones, see your phone’s user’s

guide.

3

PAIR

CONTINUED

Your Phone

Step B - SET YOUR PHONE TO LOOK FOR YOUR HEADSET

For most Motorola phones:

1

2

3

4

5

7

Place the headset over your ear.

On the phone, dial the number you want to call and press SEND key on your

phone.

If your phone and headset are successfully paired, you will hear ringing on the

headset.

After you have successfully paired your phone and headset, you don’t need to

repeat these steps. For daily use, ensure that your headset is turned ON and

that your phone’s Bluetooth feature is ON.

4

TEST AND USE

Your phone and headset are now paired and ready to make and receive calls.

To make a call:

1

2

8

USING YOUR H560

Note: If desired, your headset can be restored to original factory settings. This action will erase

all pairing information stored in your headset. Thus, you will need to pair your phone and headset

again (see step 3).

Note: To restore your headset to original factory settings, press and hold both Volume buttons and

the Call button at the same time for 10 seconds.

9

TURNING HEADSET ON AND OFF

To turn your headset on, slide the switch toward the indicator light. The indicator

light ﬂashes blue three times, then ﬂashes in blue and purple (if connected with a

device) or is steadily blue (if ready to be paired).

To turn your headset off, slide the switch toward the charging plug (the orange

color under the switch is displayed). The indicator light ﬂashes three times then

turns off.

Power

Switch

Indicator

Light

10

EARBUDS AND YOUR HEADSET

Your H560 headset is supplied with multiple earbuds. The earbud is ﬁtted onto the end

of your headset’s earpiece speaker, and placed onto your ear when using your headset.

Your headset’s performance is greatly dependent upon achieving a good ﬁt on your ear.

Therefore, we recommend trying all the supplied earbuds with your headset.

11

WEARING THE HEADSET

To wear your headset, ﬂex the earhook and loop it over your ear as shown.

Be sure to position the ear cushion into your ear canal for optimal audio performance

and comfort.

12

Gently lift and pull the top of the earhook

up and off speaker stem, as shown.

Flip the headset over.

Attach the earhook to the speaker stem,

as shown.

CHANGING FOR USE ON OTHER EAR

You can wear your H560 headset on your left or right ear. The headset comes ready

for the right ear. To change the headset for the left ear:

1

2

3

13

CHANGING VOLUME BUTTON ORIENTATION

You can also change the orientation of the volume buttons on your headset.

Turn the headset power off.

Press and hold the Volume button you want to assign as the “volume up”

button and slide the switch toward the microphone. The indicator light ﬂashes

blue three times, then steady blue. When connected, it will ﬂash blue/purple.

1

2

Volume

Buttons

Indicator

Light

14

QUICK BATTERY CHECK

When not on a call, you can check your headset’s battery charge level by pressing

and holding both Volume buttons.

The indicator light displays charge status for 5 seconds. See below for details on

indicator light and charge status.

Headset Indicator Talk Time

Red Less than 2 hours

Yellow Between 2 to 5 hours

Green Up to 7 hours

To save battery power, turn OFF the headset when you don’t use it for an extended

time by sliding the switch towards the charging plug.

15

Function Action

Receive a call Tap the Call button

Mute or unmute a call Tap both Volume buttons

Reject a call Press and hold a Volume button

until the ringer stops

End a call Tap the Call button

Redial last call Press and hold the Call button

until you hear two tones

Make a voice dial call Tap the Call button and wait for

voice prompt

Answer second incoming Use phone to answer

call

(follow your phone’s instructions)

MAKING CALLS

Note: Your H560 supports both Handsfree and Headset Proﬁles. Accessing call functions depends

upon which proﬁle your phone supports. See your phone’s user’s guide for more information.

Note: Some features are phone/network dependent.

16

INDICATOR LIGHT

Headset Indicator Headset Status

Red Charging (battery level less than

50% charge)

Yellow Charging (battery level more

than 50% charge)

Green Charging complete

With the Charger Plugged In

17

Note: After 20 minutes on a call or of inactivity, the light stops ﬂashing to conserve power, but the

headset remains on.

Headset Indicator Headset Status

Off Power off

Three blue ﬂashes Powering on/off

Steady blue Pairing/connect mode

Rapid blue/purple ﬂashes Connection successful

Quick blue ﬂash Incoming/outgoing call

Slow blue pulse Connected (on a call)

Slow blue ﬂash Standby (not on a call)

Slow red ﬂash Idle (not connected to phone)

Slow purple pulse Connected call muted

Steady red Attempting to connect

Quick red ﬂash Low battery

With No Charger Plugged In

INDICATOR LIGHT

18

Audio Tone Headset Status

Ascending tone Powering on

Two descending tones Powering off

Ring tone Incoming call

Two short tones when Volume at minimum

pressing Volume button or maximum

High/low tones Low battery

repeated every 60 sec.

No audio indications; Out of range

deteriorating quality

Two ascending tones Connected to phone

Two rapid ascending tones Mute enabled

Two rapid descending tones Mute disabled

Low tone every 10 seconds Mute reminder

AUDIO TONES

19

TROUBLESHOOTING

My headset will not enter pairing mode.

Make sure that any devices previously paired with the headset are turned off. If the

indicator light is not steadily lit in blue, turn off both the other device and headset,

wait 10 seconds, then turn headset back on. Wait for the indicator light to become

steadily lit in blue, indicating the headset is now in pairing mode.

My phone doesn’t ﬁnd my headset.

Make sure the indicator light on your headset is on (lit in blue) and steady when your

phone is searching for devices (see step 3).

My headset worked before but now it’s not working.

Make sure your phone is on and the Bluetooth feature is turned on in your phone (see

step 2). If the Bluetooth feature was turned off or was turned on only temporarily,

you may need to restart the Bluetooth feature (see step 2) and pair your phone and

headset again (see step 3).

ページが読み込まれています...

Motorola H390 - Headset - In-ear ear-bud クイックスタートガイド

このマニュアルも適しています

Motorola H390 - Headset - In-ear ear-bud クイックスタートガイド

他の言語で

関連論文

その他のドキュメント