Motorola H520 クイックスタートガイド

Quick Start Guide

MOTOROLA

H520

1

your headset

charge it

pair & connect

put it on

turn on & off

battery check

calls

status indicators

restore headset

troubleshooting

Safety & General Information

FCC Notice to Users

European Union Directives

Conformance Statement

Contents

2

3

4

6

9

10

11

13

16

17

19

23

34

2

Take a moment to familiarize yourself with your new H520 Headset.

your headset

Earhook

Charging

Port

Ear

Speaker

Indicator

Light

Microphone

Power

Switch

Call

Button

Volume

Buttons

3

charge it

The indicator light is red or purple while the battery is charging. When the battery

is fully charged, the indicator light turns blue.

Note: Before rst time use, leave headset charging overnight.

Note: Headset is not functional while charging.

Note: Your battery is designed to last the life of your product. It should only be

removed by a recycling facility. Any attempt to remove or replace your battery will

damage your headphones.

You’ll need to charge your headset overnight before using it. Plug the charger into

the charging port on your headset and a wall outlet.

4

pair & connect

Let’s get your headset paired and connected to your Bluetooth phone.

Turn off any Bluetooth devices previously paired with your headset.

Turn on the Bluetooth feature on your phone.

Turn on your headset (see page 9 for help).

The indicator light becomes steadily lit in blue.

Set your phone to search for Bluetooth devices.

Select Motorola H520 from the search results on your phone.

Select Ok or Yes to pair your headset with your phone.

Note: When prompted for the passkey, enter 0000.

The indicator light rapidly ashes blue and purple to indicate successful pairing

and connecting with your phone.

pair & connect

5

reconnect

After initially pairing and connecting your phone and headset, you don’t need to

do it again.

For daily use, make sure your headset is turned on, and your phone’s Bluetooth

feature is on. Your headset and phone will connect automatically!

test your connection

Place the headset over your ear.

On the phone, dial a number and press Call/Send key.

If your phone and headset are successfully connected, you hear ringing on the

headset.

pair & connect

6

You can wear your headset using either an earhook or ear cushion.

wear with earhook

Remove and install all the supplied earhooks to nd a good t.

Your headset comes ready for your right ear. To change for your left ear:

put it on

1 2

From Right Ear To Left Ear

7

put it on

wear with ear cushion

Remove earhook from headset.

Flex the earhook and loop it over your ear.

8

turn on & off

put it on

Try out all the supplied ear cushions to get a good t.

set volume buttons

Turn the headset power off.

Press and hold the Volume button you want to assign as the "volume up"

button and slide the Power switch on. The indicator light ashes blue three

times. When connected, it will ash blue/purple.

Volume

Buttons

Indicator

Light

9

turn on & off

turn on

Slide the Power switch to the on position (no red is shown under the switch).

The indicator light flashes blue three times, then flashes in blue and purple (if

connected with a device) or is steadily blue (if ready to be paired).

turn off

Slide the Power switch to the off position (red is shown under switch). The

indicator light ashes three times then turns off.

10

indicator light

red

purple

blue

available talk time

less than 1.5 hours

between 1.5 to 3.5 hours

up to 5 hours

battery check

Press and hold both Volume buttons while not on a call.

To save battery power, turn off the headset when you don't use it for an extended

time.

11

battery check

calls

TO…

answer call

mute or unmute a call

reject call

end a call

redial last call

make a voice dial call

answer or reject

second incoming call

Press the Call button.

Press both Volume buttons.

Press and hold a Volume button until you

hear a tone.

Press the Call button.

Press and hold the Call button until you

hear two tones.

Use phone to answer/reject second call

(follow your phone’s instructions)

Press the Call button and wait for voice

prompt.

calls

12

calls

Note: Your H520 supports both Handsfree and Headset Proles. Accessing call

functions depends upon which profile your phone supports. See your phone's

user's guide for more information.

Note: Some features are phone/network dependent.

13

calls

red

purple

blue

charging (battery level less than 50% charge)

charging (battery level more than 50% charge)

charging complete

headset indicator

headset status

status indicators

headset indicator

headset status

off

power off

three blue ashes

powering on/off

steady blue

pairing/connect mode

indicator light (with charger plugged in)

indicator light (with charger not plugged in)

14

status indicators

headset indicator

headset status

rapid blue/purple ashes

connection successful

quick blue ash

incoming/outgoing call

slow blue pulse

connected (on a call)

slow blue ash

standby (not on a call)

slow red ash

idle (not connected to a phone)

steady red

attempting to connect

quick red ash

low battery

slow purple pulse

connected(call muted)

Note: After 20 minutes on a call or of inactivity, the light stops flashing to

conserve power, but the headset remains on.

15

status indicators

audio tones

audio tone

headset status

ascending tone

powering on

two descending tones

powering of

ring tone

incoming call

two short tones when

pressing Volume button

volume at maximum or minimum

high/low tones repeated

every 60 seconds

low battery

two rapid descending tones

mute disabled

low tone every 10 seconds

mute reminder

no audio indications;

deteriorating quality

out of range

three ascending tones

connected to phone

two rapid ascending tones

mute enabled

16

restore headset

Caution: This action erases all pairing information stored in your headset.

To restore your headset to original factory settings, with the headset turned on,

press and hold both Volume buttons and Call button for 10 seconds until the

indicator light is steady blue.

17

restore headset

troubleshooting

My headset will not enter pairing mode.

Make sure that any devices previously paired with the headset are turned off.

If the indicator light is not steadily lit in blue, turn off both the other device and

headset, wait 10 seconds, then turn headset back on. Wait for the indicator light

to become steadily lit in blue, indicating the headset is now in pairing mode.

My phone doesn't nd my headset.

Make sure the indicator light on your headset is on (lit in blue) and steady when

your phone is searching for devices.

My headset worked before but now it's not working.

Make sure your phone is on and the Bluetooth feature is turned on in your phone.

If the Bluetooth feature was turned off or was turned on only temporarily, you may

need to restart the Bluetooth feature and pair your phone and headset again (see

“pair & connect” on page 4).

18

Support.

If you need more help, contact us at 1-877-MOTOBLU or visit us at

www.motorola.com/Bluetoothsupport or www.motorola.com/bluetoothconnect .

troubleshooting

19

Safety & General Information

032374o

Symbol Denition

Important safety information follows.

Do not let your battery, charger, or mobile device get wet.

IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ

THIS INFORMATION BEFORE USING YOUR DEVICE.

Approved Accessories

Use of accessories not approved by Motorola, including but not limited to

batteries, antennas, and convertible covers, may cause your mobile device

to exceed RF energy exposure guidelines and may void your mobile device’s

warranty. For a list of approved Motorola accessories, visit our Web site at:

www.motorola.com.

Batteries & Chargers

Your battery, charger, or mobile device may contain symbols, dened as follows:

troubleshooting

ページが読み込まれています...

Motorola H520 クイックスタートガイド

Motorola H520 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント