Tektronix WVR5250 Installation And Safety Instructions

xx

WVR5250

Waveform Rasterizer

Installation and Safety

ZZZ

Instructions

*P071315300*

071-3153-00

WVR5250

Waveform Rasterizer

Installation and Safety

ZZZ

Instructions

xx

www.tektronix.com

071-3153-00

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges rese rved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverto

n, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

Preface ............................................................................................................... 1

Accessories ..................................................................................................... 1

Documentation ................................................................................................. 3

General safety summary ........................................................................................... 4

Compliance information ........................................................................................... 6

EMC compliance .............................................................................................. 6

Environmental considerations................................................................................ 7

Operating requirements ............................................................................................ 8

Electrical ratings ............................................................................................... 8

Environmental ratings......................................................................................... 9

Physical speciﬁcations ........................................................................................ 9

Rear-panel connectors............................................................................................. 10

Input and output connectors ................................................................................. 10

Basic installation procedure ...................................................................................... 14

Connect a monitor ............................................................................................ 15

Install in a video system...................................................................................... 16

Power-on and Power-off procedure.............................................................................. 19

Front-panel controls ............................................................................................... 20

はじめに.................................................................................................. 22

アクセサリ ............................................................................................ 23

マニュアル ........................................................................................... 25

安全にご使用いただくために .......................................................................... 26

適合性に関する情報.................................................................................... 28

EMC 適合性......................................................................................... 28

環境に関する考慮事項 ............................................................................ 29

動作の要件 .............................................................................................. 30

電気定格 ............................................................................................ 30

環境要件 ............................................................................................ 31

物理仕様 ............................................................................................ 31

後部パネル・コネクタ.................................................................................... 32

入出力コネクタ ...................................................................................... 32

基本的な設置手順 ...................................................................................... 36

モニタの接続 ........................................................................................ 37

ビデオ・システムへの設置.......................................................................... 38

電源投入、電源切断の手順............................................................................ 41

フロント・パネル・コントロール .......................................................................... 42

前言 ...................................................................................................... 45

附件 .................................................................................................. 45

文档 .................................................................................................. 47

WVR5250 Installation and Safety Instructions i

Table of Contents

常规安全概要 ........................................................................................... 48

符合性信息 .............................................................................................. 50

EMC 符合性 .......................................................................................... 50

环境注意事项....................................................................................... 51

操作要求................................................................................................. 52

电气额定值.......................................................................................... 52

环境额定值.......................................................................................... 53

物理技术规格....................................................................................... 53

后面板连接器 ........................................................................................... 54

输入和输出连接器 ................................................................................. 54

基本安装步骤 ........................................................................................... 58

连接监视器.......................................................................................... 59

在视频系统中安

装 ................................................................................. 60

开机和关机步骤 ........................................................................................ 63

前面板控件 .............................................................................................. 64

Предисловие ...................................................................................................... 66

Принадлежности ............................................................................................ 67

Документация ................................................................................................ 69

Общи

е правила техники безопасности ....................................................................... 70

Информация о соответствии ................................................................................... 72

Электромагнитная совместимость ....................................................................... 72

Требования к защите окружающей среды .............................................................. 73

Эксплуатационные требования ................................................................................ 75

Номинальные параметры электропитания.............................................................. 75

По

казатели условий эксплуатации ....................................................................... 76

физические характеристики ............................................................................... 77

Разъемы на задней панели...................................................................................... 78

Входнойивыходнойразъемы............................................................................. 78

Основная процедура установки ............................................................................... 83

Подключение монитора .................................................................................... 84

Установка видеосистемы................................................................................... 85

Процедура включения и выключения питания ............................................................. 89

Элементы управления передней панели ..................................................................... 90

ii WVR5250 Installation and Safety Instructions

Preface

This document contains the following information:

Important safety precautions to avoid injury and prevent damage to this

product or any products connected to it

EMC (electromagnetic compliance), safety, and environmental standards

with which the instrument complies

Voltage, power, and environmental requirements to use the product

Installation procedure

Power-on and power-off procedure

Front-p

anel and rear-panel features

Accessories

Unpack

the instrument and check that you have received all of the items listed in

the following table as standard accessories. You can order optional accessories

separately. You may want to save the shipping carton and packing materials

(including the anti-static bag) in case you need to ship the instrument. Check our

Web site (www.tektronix.com) for the most curre nt information on accessories.

Accessory Standard Optional Tektronix part number

WVR5250 Waveform Rasterizer Safety and Installation Instructions (this

manual)

071-

3153-XX

WVR5250 Waveform Rasterizer P roduct Documentation CD

Thi

s CD contains various user documents. (See page 3, Documentation.)

063-4491-XX

On

e E MI suppression ferrite core. Attach to the power cord to reduce

electromagnetic interference. Impedance 240 Ω at 100 MHz.

276-0346-00

EMI suppression ferrite core installation instructions show how to attach

the ferrite core to the power cord.

07

1-2706-XX

One VGA (female) to DVI (male) display adapter to connect an external

m

onitor to the instrument.

013-0347-00

One 75 Ω terminator for use on the rear-panel connectors. The EXT REF

connector requires termination when in use.

011-0163-00

VTSRACK-S2 is a full rack (19"), short depth, 1RU adapter (with zero

clearance mounting) to ﬁt one or two (side by side) WV R5xxx instruments.

VTSRACK-L1 and V TSRACK-L2 also available.

VTSRACK-S2

VTSRACK-L1

VTSRACK-L2

Power Cord

NOTE. See the International Power Cords list that follows this table for

the type of power cord included with your instrument.

See Option number in

following table

WVR5250 Installation and Safety Instructions 1

Preface

International

power cords. Your instrument was shipped with one of the following

power cord options. Power cords for use in North America are UL listed and CSA

certiﬁed. Cords for use in areas other than North America are approved by a t least

one authority acceptable in the country to which the product is shipped.

Opt. A0 – North America power

Opt. A1 – Universal EUR power

Opt. A2 – Uni

ted Kingdom power

Opt. A3 – Australia power

Opt. A5 – Switzerland power

Opt. A6 – Japan power

Opt. A10 – China power

Opt. A11 – India power

Opt. A1

2–Brazilpower

Opt. A99

1

–NopowercordorACadapter

1

It is the responsibility of the end user to use a certiﬁed power cord for the country or region in which the

instrument is installed.

CAUTI

ON. To reduce risk of ﬁre and shock, use the certiﬁed power cord provided

with the product.

2 WVR5250 Installation and Safety Instructions

Preface

Documentation

The following table lists some of the documentation that is available for

this product and shows where you can ﬁnd it: in a printed manual, on

the product documentation CD-ROM, or on the Tektronix Web site at

www.tektronix.com/downloads.

Table 1: Pro

duct documentation

Item Purpose Location

Installat

ion and Safety Instructions

(this manual)

Provides s

afety and compliance information with

hardware installation instructions to present the

associated safety warnings. This manual is available

in English

, Japanese, and Simpliﬁed Chinese.

Printed manual and also

available

in electronic format

at www.tektronix.com/downloads

and on Product Documentation CD

User Manual

Provides

operation and application information. This

manual is available in English.

Product Documentation

CD and ava

ilable at

www.tektronix.com/downloads

Online Help

In-depth

instrument operation and UI help.

On the instrument

System Integration Technical

Reference

Provides information for system integrators designing

systems for HDMI and HD, SD, 3 Gb/s SDI video

conten

t where these instruments are being deployed.

Product

Documentation

CD and available at

www.tektronix.com/downloads

Speciﬁ

cations and Performance

Veriﬁcation Technical Reference

Speciﬁ

cations and procedures for checking instrument

performance.

Product Documentation

CD and a

vailable at

www.tektronix.com/downloads

Service Manual Provides information about adjustments, repair, and

replaceable parts.

Avail

able at

www.tektronix.com/downloads

Release Notes

Provides information about the key features and known

limi

tations of a speciﬁc software version release.

Available at

www.tektronix.com/downloads

WVR5250 Installation and Safety Instructions 3

General safety summary

General safet

ysummary

Review the fo

llowing safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perf orm service procedures.

To avoid ﬁre or personal

injury

Use proper power cord. Use only the power cord speciﬁed for this product and

certiﬁed for the country of use.

Ground the product. This product is grounded through the grounding conductor

of the power cord. To avoid electric shock, the grounding conductor must be

connected to earth ground. Before making connections to the input or output

terminals of the product, ensure that the product is properly grounded.

Observe all terminal ratings. To avoid ﬁre or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

Do not apply a potential to any terminal, i

ncluding the common terminal, that

exceeds the maximum rating of that terminal.

Power disconnect. The p ower cord disconnects the product from the power

source. Do not block the power cord; it must remain accessible to the user at

all times.

Do not operate without covers. Do not operate this product with covers or panels

removed.

Do not operate with suspected failures. If you suspect that there is damage to this

product, have it inspected by qualiﬁed service p ersonnel.

Avoid exposed circuitry. Do not touch exposed connections and components

when power is present.

Use proper AC adapter. Use only the AC adapter speciﬁed for this product.

Do not operate in wet / damp conditions.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

Provide proper ventilation. Refer to t he manual's installation instructions for

details on installing the product so it has proper ventilation.

4 WVR5250 Installation and Safety Instructions

General safety summary

Terms in this manual

These terms may

appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

Symbols and terms on the

product

These terms may appear on the product:

DANGER in

dicates an injury hazard immediately accessible as you read

the marking.

WARN IN G

indicates an injury hazard not immediately accessible as you

read the marking.

CAUTIO

N indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

WVR5250 Installation and Safety Instructions 5

Compliance information

Compliance in

formation

This section

lists the EMC (electromagnetic compliance), safety, and

environmental standards with which the instrument complies.

EMC compliance

EC Declaration of

Conformity – EMC

Meets intent of Directive 2 004/108/EC for Electromagnetic Compatibility.

Compliance was demonstrated to the following speciﬁcations as listed in the

Ofﬁcial Journal of the European Communities:

EN 55103:2009. Product family standard for audio, video, audio-visual and

entertainment lighting control apparatus for professional use.

1

,

2

Environment E2 – commercial and light industrial

Part 1 Emission

EN 55022:2006. Class B radiated and conducted emissions

EN 55103-1:2009 Annex A. Radiated magnetic ﬁeld emissions

Part 2 Immunity

IEC 61000-4-2+A1+A2:2000. Electrostatic discharge immunity

IEC 61000-4-3+A1:2007. RF electromagnetic ﬁeld immunity

IEC 61000-4-4:2004. Electrical fast transient / burst immunity

IEC 61000-4-5:2005. Power line surge immunity

IEC 61000-4-6+A1+A2:2006. Conducted RF Immunity

IEC 61000-4-11:2004. Voltage dips and interruptions immunity

EN 55103-2:2009 Annex A. Radiated magnetic ﬁeld immunity

1

For compliance with the EMC standards listed here, high-quality shielded interface cables should be used.

2

Average half-cycle r.m.s. inrush current at initial switch-on and after 5 second power interruption: 3A.

EN 61000-3-2:2006. AC power line harmonic emissions

EN 61000-3-3:1995. Voltage changes, ﬂ uctuations, and ﬂicker

European contact.

Tektronix UK, Ltd.

Western Peninsula

Western Road

Bracknell, RG12 1RF, United Kingdom

6 WVR5250 Installation and Safety Instructions

Compliance information

Australia / New Zealand

Declaration of

Conformity – EMC

Compliance was

demonstrated to EN 55022:2006, radiated and conducted

emissions, Class B, in accordance with:

EN 55103:2009

Environmental considerations

This sectio

n provides information about the environmental impact of the product.

Product end-of-life

handling

Observe the following guidelines when recycling an instrument or component:

Equipmen

t recycling.

Production of this equipment required the extraction and use of natural resources.

The equipment may contain substances that could be harmful to the environment

or human

health if improperly handled at the product’s end o f life. In order to avoid

release of such substances into the environment and to reduce the use of natural

resources, we encourage you to recycle this product in an appropriate system that

will ensure that most of the materials are reused or recycled appropriately.

This symbol indicates that this product complies with the applicable European

Union requirements according to Directives 2002/96/EC and 2006/66/EC

on waste electrical and electronic equipment (WEEE) and batteries. For

information about recycling options, check the Support/Service section of the

Tektronix Web site (www.tektronix.com).

Perchlorate m aterials. This product contains one or more type CR lithium

batteries. According to the state of California, CR lithium batteries are

classiﬁed as perchlorate materials and require spe cia l handling. See

www

.dtsc.ca.gov/hazardouswaste/perchlorate for additional information.

Restriction of hazardous

substances

This product is cla ssiﬁ ed as an industrial monitoring and control instrument,

and is not required to comply with the substance restrictions of the recast RoHS

Di

rective 2011/65/EU until July 22, 2017.

WVR5250 Installation and Safety Instructions 7

Operating requirements

Operating req

uirements

This section

provides the speciﬁcations that you need to know to operate your

product safely and c orrectly. Refer to the complete product speciﬁcations for

additional information.

Electrical ratings

Power requirements

Power connector

NOTE. If you ordered a power cord, it will come with a ferrite core. Install the

ferrite core as shown in the instructions with which it was shipped.

The instrument operates from an external AC adapter and has the following power

requirements:

A single-phase power s ource with one current-carrying conductor at or near

earth-ground (the neutral conductor).

The power source frequency must be 50 or 60 Hz, and a operating voltage

range must be from 100 to 240 VAC, continuous.

WAR

NING. To reduce risk of ﬁre and shock, make sure the mains supply voltage

ﬂuctuations do not exceed 10% of the operating voltage range.

Sy

stems with both current-carrying conductors live with respect to ground

(such as phase-to-phase in multiphase systems) are not recommended as

power sources.

NOTE. Only the line conductor is fused for over-current protection. The fuse is

internal and not user replaceable. Do not attempt to replace the fuse. If you

suspect the fuse has blown, return the unit to an authorized service center for

repair.

8 WVR5250 Installation and Safety Instructions

Operating requirements

Environmental ratings

Table 2: Environmental performance

Category Standards or description

Operating 0 °C to +40 °C

Temperature

Non operating

–20 °C to +60 °C

Operating 20% to 80% relative humidity at up to +40 °C, noncondensing

Humidity

Non operating

Below 5% or above 90% relative humidity at up to +60 °C, noncondensing

Operating Up to 9,842 feet (3,000 meters)

Altitude

Non operating

Up to 40,000 feet (12,192 meters)

The variable fans provide forced air circulation.

Base

instrument

(no opt

ional

sleeves)

Do not block more than half the vent holes on the sides.

Cooling

Rack

Use only the VTSRACK-S2, VTSRACK-L1, or VTSRACK-L2 rackmount adapter for this

instrument. The rack intake air to the side vents must not exceed 40 °C.

Physical speciﬁcations

Tabl

e 3: Physical characteristics

Characteristic Standard

Heig

ht

1.71 inches (43.4 m illimeters)

Wid

th

8.12 inches (206.3 m illimeters)

Dime

nsions

De

pth

4.75 inches (120.7 m illimeters)

Ne

t

1.8 pounds (0.82 kilograms)

We

ight

Shipping 12 pounds (4.08 kilograms), approximate, excluding options and accessories

Cleaning

Not required for the safe operation of the instrument. However, if you wish to

perform routine cleaning on the exterior of the instrument, refer to the user manual

on the Product Documentation CD that was shipped with your instrument.

WVR5250 Installation and Safety Instructions 9

Rear-panel connectors

The following ﬁgure shows the rear-panel.

Rear-panel

Input and output connectors

Video connectors

SDI and HDMI inputs are self-terminating inputs.

Input

Connector

REF LOOP. A synchronization input. The input signal can be

analog black burst, analog composite v ideo, or analog tri-level

for HD. Requires termination.

NOTE. The reference input is a passive loop input, so external

termination is required.

SDI 1A. The digital A component serial digital input.

SDI 1B. The digital B component serial digital input.

HDMI 2A. The2Ahighdeﬁnition multimedia interface input.

HDMI 2B. The2Bhighdeﬁnition multimedia interface input.

10 WVR5250 Installation and Safety Instructions

Rear-panel connectors

Output Connector

SDI OUT. Select to output Loop Out, Pixmon, or Test Signals

(with Option GEN installed) for SD-SDI, HD-SDI, or 3G-SDI

(Level A or lev

el B)

1

.

HDMI OUT. Thehighdeﬁnition multimedia interface loop output.

1

3G-SDI Test Signals are available with Option 3G installed.

EXT DISPLAY connector

This is the e

xternal display monitor output. The display resolution is 1024 x

768. The output supports DVI monitors directly and analog PC (RGB) monitors

with the use of a DVI-I to VGA adapter. The EXT DISPLAY connector is a

DVI-I connector with socket contacts.

EXT DISPLAY connector

NOTE. A compliant HDCP monitor is required to view HDCP signals.

WVR5250 Installation and Safety Instructions 11

Rear-panel connectors

REMOTE connector pin

assignment

The REMOTE conn

ector interface uses ground closures for remote control and

indicating to external equipment when alarms have occurred. The input o f LTC is

through the REMOTE connector. The REMOTE connector is a 15-pin D-type

connector with socket contacts

NOTE. For more information on Preset recall, refer to the user manual on the

Product Documentation CD that was shipped with your instrument.

Remote connector preset function pin assignments.

Characteristic Pin out Preset functions

Connector Pin Assignments

Hex Binary

Pins 15,

14, 13,

12, 11,

10

Direct

mode

selection

Encoded

mode

selection

F 111111

none

No action

E XX1110 Preset 1 HDMI B

D XX1101 Preset 2 HDMI A

C

XX1100

SDI B

B XX1011 Preset 3

SDI A

A XX1010

Channel B

9 XX1001

Channel A

8 XX1000 Preset 8

7

XX0111 Preset 4 Preset 7

6 XX0110 Preset 6

5

XX0101 Preset 5

4 XX0100 Preset 4

3 XX0011 Preset 3

2 XX0010 Preset 2

1 XX0001 Preset 1

1GND(In)

2 Reserved (I/O)

3 Reserved (I/O)

4 R eserved (In)

5 R eserved (In)

6GND(In)

7 Time Code Positive (LTC In)

8 Time Code Negative (LTC In)

9 Ground Closure (Alarm Out)

10 Preset 1 (In)

11 Preset 2 (In)

12 Preset 3 (In)

13 Preset 4 (In)

14 Preset 5 (In)

15 Preset 6 (In)

0 XX0000 Unused

12 WVR5250 Installation and Safety Instructions

Rear-panel connectors

Camera Tally mo

de pin assignments. Used to deﬁne which input is On-Air (RED)

and w hich input is available to be adjusted (GREEN). This state is indicated i n t he

Status Bar and above the Picture display of the selected input. When a suitable

input is grounded, the state RED or GREEN state will be asserted depending

on the p in selected. Yellow will appear when both a ‘RED’ and ‘GREEN’ pin

for an input is selected.

Characteristic Pin out camera tally encoded mode

Connector pin assignments 1GND(In)

2 Not available

3 Not available

4 Channel 2A Green

5 Channel 2B Green

6GND(In)

7 Time Code Positive (LTC In)

8 Time Code Negative (LTC In)

9 Ground Closure (Alarm Out)

10 Channel 1A Red

11 Channel 1B Red

12 Channel 2A Red

13 Channel 2B Red

14 Channel 1A Green

15 Channel 1B Green

Ethernet connector

The instrument provides a 10/100/1000 BaseT Ethernet interface. The Ethernet

connector is a standard RJ-45 connector.

Ethernet connector

WVR5250 Installation and Safety Instructions 13

Basic installation procedure

Your instrument is shipped in a fully enclosed metal chassis. You can operate the

instrument in the provided chassis or install the chassis in an approved portable

cabinet or ra

ck adapter.

To install your instrument in a cabinet or rack, follow the instructions that are

included wi

th the optional accessory kits that are available for each type of

installation. Also refer to the Environmental Ratings section for cooling and

clearance requirements. (See page 9, Environmental ratings.)

CAUTION. Do not i nstall this instrument in any cabinet except those that are

listed in the Accessories table; attempting to do so can damage the instrument

and the cabinet.

If you need to install your instrument in a custom application, such as a console,

be sure to provide adequate airﬂow and make sure the intake air to the side vents

do not exceed 40 °C. Do not block or restrict the ventilating holes. Refer to the

Environmental Ratings section for cooling and clearance requirements. (See

page 9, Environmental ratings.)

When installing in a custom application, use the Rack Adapter clearances.

CAUTION. To prevent risk of ﬁre, adequate airﬂow must be maintained. Failure

to pr

ovide adequate airﬂow to the instrument could cause the instrument to

shut down. Inadequate a irﬂow includes placing the instrument in any small,

enclosed room that lacks a ventilation system, such as a closet. If the airﬂow is

restricted or blocked and the instrument does not shut down, the instrument c ould

be permanently damaged and increases the risk of ﬁre.

14 WVR5250 Installation and Safety Instructions

ページが読み込まれています...

Tektronix WVR5250 Installation And Safety Instructions

Tektronix WVR5250 Installation And Safety Instructions

他の言語で

関連論文

その他のドキュメント