Tektronix WVR5200 Series Instructions Manual

タイプ
Instructions Manual

このマニュアルも適しています

xx
WFM5200
Waveform Monitor
Installation and Safety
ZZZ
Instructions
*P071288702*
071-2887-02
WFM5200
Waveform Monitor
Installation and Safety
ZZZ
Instructions
xx
www.te ktronix.com
071-2887-02
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specications and price change privileges rese rved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverto
n, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to nd contacts in your area.
Table of Contents
Preface ............................................................................................................... 1
Accessories ..................................................................................................... 2
Documentation................................................................................................. 3
General Safety Summary .......................................................................................... 5
Compliance Information ........................................................................................... 7
EMC Compliance.............................................................................................. 7
Environmental considerations................................................................................ 8
Operating Requirements ........................................................................................... 9
Electrical Ratings .............................................................................................. 9
Environmental Ratings....................................................................................... 10
Physical Specications....................................................................................... 11
Rear-Panel Connectors............................................................................................ 12
Input and Output Connectors ................................................................................ 12
Basic Installation Procedure...................................................................................... 15
Installing in a Video System ......... .................................. .................................. .... 16
Power-On and Power-Off Procedure ............................................................................ 19
Front-Panel Controls .............................................................................................. 20
はじめに.................................................................................................. 22
アクセサリ ............................................................................................ 23
マニュアル ........................................................................................... 24
安全にご使用いただくために .......................................................................... 26
適合性に関する情報.................................................................................... 28
EMC ......................................................................................... 28
環境に関する考慮事項 ............................................................................ 29
動作の要件 .............................................................................................. 30
電気定格 ............................................................................................ 30
環境要件 ............................................................................................ 32
物理仕様 ............................................................................................ 32
リア・パネル・コネクタ.................................................................................... 33
入出力コネクタ ...................................................................................... 33
基本的な設置手順 ...................................................................................... 36
ビデオ・システムへの設置.......................................................................... 37
電源投入、電源切断の手順............................................................................ 40
フロント・パネル・コントロール .......................................................................... 41
前言 ...................................................................................................... 43
附件 .................................................................................................. 44
文档 .................................................................................................. 45
WFM5200 Installation and Safety Instructions i
Table of Contents
常规安全概要 ........................................................................................... 47
符合性信息 .............................................................................................. 49
EMC .......................................................................................... 49
环境注意事项....................................................................................... 50
操作要求................................................................................................. 51
电源额定值.......................................................................................... 51
环境额定值.......................................................................................... 52
物理技术规格....................................................................................... 53
后面板连接器 ........................................................................................... 54
输入和输出连接器 ................................................................................. 54
基本安装步骤 ........................................................................................... 57
在视频系统中安装 ................................................................................. 58
开机和关机步骤
........................................................................................ 61
前面板控件 .............................................................................................. 62
ii WFM5200 Installation and Safety Instructions
Preface
This document contains the following information:
Important safety precautions to avoid injury and prevent damage to this
product or any products connected to it
EMC (electromagnetic compliance), safety, and environmental standards
with which the instrument complies
Voltage, power, and environmental requirements to use the product
Installation procedure
Power-on and power-off procedure
Front-p
anel and rear-panel features
WFM5200 Installation and Safety Instructions 1
Preface
Accessories
Unpack the instrument and check that you have received all of the items listed in
the following table as standard accessories. You can order optional accessories
separately. You may want to save the shipping carton and packing materials
(including the a nti-static bag) in case you need to ship the instrument. Check our
Web site (ww
w.tektronix.com) for the most current information on accessories.
Accessory Standard Optional Tektronix part number
WFM5200 Waveform Monitor Product D ocumentation Kit
This kit co
ntains this printed manual (071-2887-XX) and a CD
(063-4341-XX) containing various user documents. (See page 3,
Documentation.)
020-3075-XX
One EMI suppression ferrite core. Attach to the power cord to reduce
electrom
agnetic interference. Impedance 240 at 100 MHz.
276-0346-00
EMI supp
ression ferrite core installation instructions show how to attach
the ferrite core to the power cord.
071-2706-XX
One VGA (female) to DVI (male) display adapter to connect an external
monitor to the instrument.
013-03
47-00
One 75 terminator for use on the rear-panel connectors. The EXT REF
conne
ctor requires termination when in use.
011-0163-00
WFM50
F01, portable cabinet with handle, feet, tilt bail, and front-panel
cover.
WFM50F01
WFMRACK-NN accommodates two WFM8xxx, WFM7xxx, or WFM6xxx.
Also includes two short depth adaptors to accommodate two WFM5xxx or
WFM4
000.
WFMRACK-NN
WFM
RACK-ON accommodates one older unit (1700 Series, WFM601, or
764 and one new unit, such as the W F M 8xxx, WFM7xx x, or WFM 6xxx.
Also includes one short depth adapter (only usable in NEW Sleeve) for
th
e WFM5xxx or WFM4000.
WFM
RACK-ON
Po
wer Cord
NOTE. See the International Power C ords list that follows this table for
the type of power cord included with your instrument.
Not applicable
2 WFM5200 Installation and Safety Instructions
Preface
International
power cords. Your instrument was shipped with one o f the following
power cord options. Power cords for use in North America are UL listed and CSA
certied. Cords for use in areas other than North America are approved by at least
one authority acceptable in the country to which the product is shipped.
Opt. A0 North America power
Opt. A1 Universal EUR power
Opt. A2 United Kingdom power
Opt. A3 Australia power
Opt. A5 Switzerland power
Opt. A6 Japan power
Opt. A10 China power
Opt. A11 India power
Opt. A12 Brazil power
Opt. A99
1
No power cord or AC adapter
1
When ordering the A99 option, it is the responsibility of the end user to be sure that a certied power cord, for the
country or region it is installed, is used with this instrument.
CAUTION. To reduce risk of re and shock, use the certied power cord provided
with the product.
Documentation
The following table lists some of the documentation that is available for this
product and shows where you can nd it: in a printed manual, on the product
documentation CD-ROM, or on the Tektronix Web site at www.tektronix.com.
Table 1: Product documentation
Item Purpose Location
Installation and Safety Instructions
(this manual)
Provides safety and compliance information with
hardware installation instructions to present the
associated safety warnings. This manual is available
in English, Japanese, and Simplied Chinese.
Printed manual and also
available in electronic format
at www.tektronix.com/manuals
User Manual
Provides operation and application information. This
manual is available in English.
Product Documentation
CD and available at
www.tektronix.com/manuals
Online Help
In-depth instrument operation and UI help.
On the instrument
System Integration Technical
Reference
Provides information for system integrators designing
systems for HD, SD, and 3 Gb/s SDI video content
where these instruments are being deployed.
Product Documentation
CD and available at
www.tektronix.com/manuals
WFM5200 Installation and Safety Instructions 3
Preface
Table 1: Product documentation, (cont.)
Item Purpose Location
Specications and Performance
Verication Technical Reference
Specications and procedures for checking instrument
performance.
Product Documentation
CD and available at
www.tektronix.com/manuals
WFM and WVR Series
Management Information
Database (MIB) Programmer
Manual
SNMP command reference for remotely controlling the
instrument.
Product Documentation
CD and available at
www.tektronix.com/manuals
Service Manual Provides information about adjustments, repair, and
replaceable parts.
Available at
www.tektronix.com/manuals
Release Notes
Provides information about the key features and known
limitations of a specic software version release.
Available at
www.tektronix.com/manuals
4 WFM5200 Installation and Safety Instructions
General Safety Summary
General Safet
ySummary
Review the fo
llowing safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specied.
Only qualied personnel should perform service procedures.
To Avoid Fire or Personal
Injury
Use Proper Power Cord. Use only the power cord specied for this product and
certied for the country of use.
Ground the Product.. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid re or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Power Disconnect.. The power cord disconnects the product from the power
source. Do not block the power cord; it must remain accessible to the user at
all times.
Do Not Operate Without Covers. Do not operate this product with covers or
panels removed.
Do Not Operate With Suspected Failures. If you suspect that there is damage to
this product, have it inspected by qualied service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Use Proper AC Adapter. Use only the AC adapter specied for this p roduct.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual's installation instructions for
details on installing the product so it has proper ventilation.
WFM5200 Installation and Safety Instructions 5
General Safety Summary
TermsinthisManual
These terms may
appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Symbols and Terms on the
Product
These terms may appear on the product:
DANGER in
dicates an injury hazard immediately accessible as you read
the marking.
WAR N I N G
indicates an injury haza rd not immediately a ccessible as you
read the marking.
CAUTIO
N indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
6 WFM5200 Installation and Safety Instructions
Compliance Information
Compliance In
formation
This section
lists the EMC (electromagnetic compliance), safety, and
environmental standards with which the instrument complies.
EMC Compliance
EC Declaration of
Conformity EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.
Compliance was demonstrated to the following specications as listed in the
Ofcial Journal of the European Communities:
EN 55103:1996. Product family standard for audio, video, audio-visual and
entertainment lighting control apparatus for professional use.
1
,
2
Environment E2 commercial and light industrial
Part 1 Emission
EN 55022:1987. Class B radiated and conducted emissions
EN 55103-1:1996 Annex A. Radiated magnetic eld emissions
Part 2 Immunity
IEC 61000-4-2:2001. Electrostatic discharge immunity
IEC 61000-4-3:2006. RF electromagnetic eld immunity
IEC 61000-4-4:2004. Electrical fast transient / burst immunity
IEC 61000-4-5:2005. Power line surge immunity
IEC 61000-4-6:2003. Conducted R F Immunity
IEC 61000-4-11:2004. Voltage dips and interruptions immunity
EN 55103-2:1996 Annex A Radiated magnetic eld immunity
EN 55103-2:1996 Annex B Balanced ports common mode immunity
1
For compliance with the EMC standards listed here, high-quality shielded interface cables should be used.
2
Inrush current: 8 A peak.
EN 61000-3-2:2006. AC power line harmonic emissions
EN 61000-3-3:1995. Voltage changes, uctuations, and icker
European Contact.
Tektronix UK, Ltd.
Western Peninsula
Western Road
Bracknell, RG12 1RF, United Kingdom
WFM5200 Installation and Safety Instructions 7
Compliance Information
Australia / New Zealand
Declaration of
Conformity EMC
Complies with t
he EMC provision of the Radiocommunications Act per the
following standard, in a ccordance with ACMA:
EN 55022:1987
. Radiated and conducted emissions, Class B, in accordance
with EN 55103-1:1996.
Environmental considerations
This section provides information about the environmental impact of the product.
Product end-of-life
handling
Observe the following guidelines when recycling an instrument or component:
Equipment recycling.
Production of this equipment r equired the extraction and use of natural resources.
The equi
pment may contain substances that could be harmful to the environment
or human health if improperly handled at the product’s end of life. In order to avoid
release of such substances into the environment and to reduce the use of natural
resources, we encourage you to recycle this product in an appropriate system that
will ensure that most of the materials are reused or recycled appropriately.
This symbol indicates that this product complies with the applicable European
Union
requirements according to Directives 2002/96/E C and 2006/66/EC
on waste electrical and electronic equipment (WEEE) and batteries. For
information about recycling options, check the S upport/Service section of the
Tek tr
onix Web site (www.tektronix.com).
Perchlorate materials. This product contains one or more type CR lithium
batteries. According to the state of California, CR lithium batteries are
cla
ssied as perchlorate materials and require special handling. See
www.dtsc.ca.gov/hazardouswaste/perchlorate for additional information.
Restriction of hazardous
su
bstances
This product is classied as an industrial monitoring and control instrument,
an
d is not required to comply with the substance restrictions of the recast RoHS
Directive 2011/65/EU until July 22, 2017.
8 WFM5200 Installation and Safety Instructions
Operating Requirements
Operating Req
uirements
This section
provides the specications that you need to know to operate your
product safely and correctly. Refer to the complete product specications for
additional information.
Electrical Ratings
Power Requ irements
Power connector
NOTE. If you ordered a power cord, it will come with a ferrite core. Install the
ferrite core as shown in the instructions with which it was shipped.
The instrument operates from an external AC adapter and has the following power
requirements:
A single-phase power source with one current-carrying conductor at or near
earth-ground (the neutral conductor).
The power source frequency must be 50 or 60 Hz, and a operating voltage
range m ust be from 100 to 240 VAC, continuous.
WAR
NING. To re duce risk of re and shock, make sure the mains supply voltage
uctuations do not exceed 10% of the operating voltage range.
Sy
stems with both current-carrying conductors live with respect to ground
(such as phase-to-phase in multiphase systems) are not recommended as
power sources.
NOTE. Only the line conductor is fused for over-current protection. The fuse is
internal and not user replaceable. Do not attempt to replace the fuse. If you
suspect the fuse has blown, return the unit to an authorized service center for
repair.
WFM5200 Installation and Safety Instructions 9
Operating Requirements
Battery Power
This instrumen
t can be powered by a 12 V DC input or by a 14.4 V standard
camera battery. If you are using a battery with this instrument, read the following
battery safety notices. This instrument was designed to be used with an Anton
Bauer battery. It can also be used with a Sony or IDX V-mount style battery.
CAUTION. Before using the Anton Bauer Power Tap feature, refer to the product
information included with the battery. If that information is not available, contact
the battery
manufacturer for information.
WARNING. Fire can cause personal injury and/or property damage. To prevent
risk of r
e, when using a 12 V DC source other than the provided AC adapter,
make sure that it has a suitable current limiting device (such as a fuse).
WARNING
. Risk of personal injury and/or property damage from falling
instrument. Batteries from various manufacturers may vary in shape and weight.
When a battery is installed, it is possible that it will make the unit too heavy in the
back, causing the instrument to tip backward.
Environmental Ratings
Table 2: Environmental performance
Category Standards or description
Operating 0 °C to +40 °C
Temperature
Non Operating –20 °C to +60 °C
Operating 20% to 80% relative humidity relative humidity at up to +40 °C, noncondensing
Humidity
Non Operating below 5% or above 90% RH (relative humidity) at up to +60 °C, noncondensing
Operating Up to 9,842 feet (3,000 meters)
Altitude
Non Operating Up to 40,000 feet (12,192 meters)
The variable fans provide forced air circulation. Do not block ventilation openings.
Bare
Instrument
(no optional
sleeves)
To allow for proper airow, there must be at least 2 inches of clearance on both sides of
the instrument, at least 2 inches of clearance from the rear of the instrument, and at least a
1/2 inch of clearance from the top of the instrument.
Portable
Cabinet
Use only the Tektronix portable cabinet, WFMF02, to allow for proper airow with this
instrument. When using the portable c abinet, the same minimum clearances as the Bare
Instrument apply.
Cooling
Rack Cabinet Use only the WFMRACK-NN or WFMRACK-ON rackmount rack adapter for this instrument. To
allow for proper airow when installing the rack adapter in a closed rack with solid walls, there
must be at least 2 inches of clearance from both sides of the rack adapter frame to the rack side
walls, at least 3 inches of clearance from the rear of the rack adapter frame to the back wall of
the rack, and at least a 1/2 inch of clearance from the top of the rack adapter to another rack
adapter or installed instrument. The rack intake air to the side vents must not exceed 40 °C.
10 WFM5200 Installation and Safety Instructions
Operating Requirements
Physical Spec
ications
Table 3: Physical characteristics
Characteris
tic
Standard
Height
5.25 inches (
133.4 millimeters)
Width
8.5 inches (
215.9 millimeters)
Dimensions
Depth
4.75 inche
s (120.7 millimeters)
Net
3.3 pounds
(1.5 kilograms)
Weight
Shipping 12 pounds
(5.4 kilograms), approximate, excluding options and accessories
Cleaning
Not requ
ired for the safe operation of the instrument. However, if you wish to
perform routine cleaning on the exterior of the instrument, refer to the user manual
on the Product Documentation CD that was shipped with your instrument.
WFM5200 Installation and Safety Instructions 11
Rear-Panel Connectors
Rear-Panel Co
nnectors
The followin
g gure shows the rear-panel. The SDI inputs are arranged
horizontally and the external reference connectors are arranged vertically.
Rear-panel
Input and Output Connectors
Video Connectors
SDI inputs are self-terminating inputs.
Input
Connector
REF Loop. A synchronization input. The input signal can be
analog black burst, analog composite v ideo, or analog tri-level
for HD. Requires termination.
NOTE. The reference input is a passive loop input, so external
termination is required.
SDI 1A. The digital A c omponent serial digital input.
SD
I1B.The digital B component serial digital input.
SDI 2A. The digital A c omponent serial digital input.
SDI 2B. The digital B c omponent serial digital input.
12 WFM5200 Installation and Safety Instructions
Rear-Panel Connectors
Output Connector
SDI Out. Select to output Loop Out or Test S ignals (with Option
GEN installed) for SD-SDI, HD-S DI, or 3G-SDI (Level A or level
B)
1
.
1
3G-SDI Test Signals are available with Option 3G installed.
EXT DISPLAY C
onnector
Pin Assignment
This is the external display monitor output. The display resolution is 1024 x
768. The output supports DVI monitors directly and analog PC (RGB) monitors
with the use of a DVI-I to VGA adapter. The EXT DISPLAY connector is a
DVI-I conn
ector with socket contacts.
EXT DISPLAY connector
REMOTE C
onnector Pin
Assignment
The REMOTE connector interface uses ground closures for remote control and
indicating to external equipment when alarms have occurred. The input of LTC is
through the REMOTE connector. The REMOTE connector is a 15-pin D-type
connec
tor with socket contacts
NOTE. For more information on Preset recall, refer to the user manual on the
Product Documentation CD that was shipped with your instrument.
WFM5200 Installation and Safety Instructions 13
Rear-Panel Connectors
Remote connect
or preset functions.
Characteristic Pin out Preset functions
Connector Pin Assignments
Hex Binary
Pins 15,
14, 13,
12, 11,
10
Direct
mode
selection
Encoded
mode
selection
F 111111
none
No action
E XX1110 Preset 1 No action
D XX1101 Preset 2 No action
C
XX1100
SDI B
B XX1011 Preset 3
SDI A
A XX1010 No action
9 XX1001 No action
8 XX1000 Preset 8
7
XX0111 Preset 4 Preset 7
6 XX0110 Preset 6
5
XX0101 Preset 5
4 XX0100 Preset
4
3 XX0011 Preset 3
2 XX0010 Preset 2
1 XX000
1
Prese
t1
0 XX0000 Unused
N/A
101111 Preset 5
N/A
1GND(In)
2 Reserved (I/O)
3 Reserved (I
/O)
4 R eserved (In)
5 R eserved (In)
6GND(In)
7 Time Code Positive (LTC In)
8 Time C ode Negative (LTC In)
9 Ground Cl
osure (Alarm Out)
10 Preset 1 (In)
11 Preset 2 (In)
12 Preset
3(In)
13 Preset 4 (In)
14 Preset 5 (In)
15 Prese
t6(In)
N/A
011111 Preset 6
N/A
Ethernet Connector
The instrument provides a 10/100/1000 BaseT Ethernet interface. The Ethernet
connector is a standard RJ-45 connector.
E
thernet connector
14 WFM5200 Installation and Safety Instructions
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Tektronix WVR5200 Series Instructions Manual

タイプ
Instructions Manual
このマニュアルも適しています

他の言語で