Makita ST001G ユーザーマニュアル

ST001G

ST002G

EN Cordless Stapler INSTRUCTION MANUAL 5

ZHCN 充电式马钉枪使用说明书 14

ID Stapler Tanpa Kabel PETUNJUK PENGGUNAAN 23

MS Pengokot Tanpa Kord MANUAL ARAHAN 33

VI Máy Bắn Đinh Cầm Tay Hoạt

Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 42

TH   51

1 1

Fig.1

Fig.2

Fig.3

1 2

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

5ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: ST001G ST002G

Staple width 4 mm 10 mm

Applicable staples length 13 mm - 25 mm

Staple magazine capacity 100 pcs

Dimensions (L x W x H) *1*2 269 mm x 86 mm x 216 mm

Rated voltage D.C. 36 V - 40 V max

Net weight 2.5 - 3.7 kg

*1 without hook

*2 with battery model BL4025

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsandbatterycartridgemaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

estcombinations,accordingtoEPTA-Procedure01/2014,areshowninthetable.

Applicable battery cartridge and charger

Battery cartridge BL4020*/BL4025*/BL4040*/BL4050F/BL4080F

* : Recommended battery

Charger DC40RA/DC40RB/DC40RC

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

andchargersmaycauseinjuryand/orre.

Symbols

Thefollowingsshowthesymbolswhichmaybeused

fortheequipment.Besurethatyouunderstandtheir

meaningbeforeuse.

Read instruction manual.

Ni-MH

Li-ion

OnlyforEUcountries

Duetothepresenceofhazardouscom-

ponentsintheequipment,wasteelectrical

andelectronicequipment,accumulators

and batteries may have a negative impact

on the environment and human health.

Donotdisposeofelectricalandelectronic

appliances or batteries with household

waste!

InaccordancewiththeEuropeanDirective

onwasteelectricalandelectronicequip-

ment and on accumulators and batteries

andwasteaccumulatorsandbatteries,

aswellastheiradaptationtonationallaw,

wasteelectricalequipment,batteriesand

accumulators should be stored separately

and delivered to a separate collection point

formunicipalwaste,operatinginaccor-

dance with the regulations on environmen-

tal protection.

Thisisindicatedbythesymbolofthe

crossed-out wheeled bin placed on the

equipment.

Intended use

Thetoolisintendedforpressingstaplesintoconstruc-

tion materials such as timbers.

SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instruc-

tions, illustrations and specications provided with

this power tool.Failuretofollowallinstructionslisted

belowmayresultinelectricshock,reand/orserious

injury.

Save all warnings and instruc-

tions for future reference.

Theterm“powertool”inthewarningsreferstoyour

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

6ENGLISH

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust.Powertoolscreatesparks

whichmayignitethedustorfumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduceriskofelectricshock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tricshockifyourbodyisearthedorgrounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

theriskofelectricshock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increasetheriskofelectricshock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use.Useof

acordsuitableforoutdoorusereducestheriskof

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.UseofanRCDreduces

theriskofelectricshock.

7. Power tools can produce electromagnetic

elds (EMF) that are not harmful to the user.

However,usersofpacemakersandothersimilar

medicaldevicesshouldcontactthemakeroftheir

deviceand/ordoctorforadvicebeforeoperating

this power tool.

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication.Amomentofinattentionwhileoperating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection.Protectiveequipmentsuch

asadustmask,non-skidsafetyshoes,hardhator

hearingprotectionusedforappropriateconditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attachedtoarotatingpartofthepowertoolmay

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

ofthepowertoolinunexpectedsituations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.Looseclothes,jewelleryor

long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.Useof

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

cancausesevereinjurywithinafractionofa

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rateforwhichitwasdesigned.

2. Do not use the power tool if the switch does

not turn it on and o. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools.Suchpreventivesafetymeasuresreduce

theriskofstartingthepowertoolaccidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool.Powertoolsaredangerousinthe

handsofuntrainedusers.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

7ENGLISH

6. Keep cutting tools sharp and clean.Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed.Useofthepowertool

foroperationsdierentfromthoseintendedcould

result in a hazardous situation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handlesandgraspingsurfacesdonotallowfor

safehandlingandcontrolofthetoolinunexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled.Theentangle-

mentofclothworkglovesinthemovingpartsmay

resultinpersonalinjury.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer.Achargerthatissuitablefor

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs.Useofanyotherbattery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

may exhibit unpredictable behaviour resulting in

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Never service damaged battery packs. Service

ofbatterypacksshouldonlybeperformedbythe

manufacturerorauthorizedserviceproviders.

3. Follow instruction for lubricating and chang-

ing accessories.

Cordless stapler safety warnings

1. Always assume that the tool contains fasten-

ers.Carelesshandlingofthestaplercanresultin

unexpectedringoffastenersandpersonalinjury.

2. Do not point the tool towards yourself or any-

one nearby. Unexpected triggering will discharge

thefastenercausinganinjury.

3. Do not actuate the tool unless the tool is

placed rmly against the workpiece.Ifthetool

isnotincontactwiththeworkpiece,thefastener

maybedeectedawayfromyourtarget.

4. Disconnect the tool from the power source

when the fastener jams in the tool. While

removingajammedfastener,thestaplermaybe

accidentallyactivatedifitispluggedin.

5. Use caution while removing a jammed fas-

tener.Themechanismmaybeundercompression

andthefastenermaybeforcefullydischarged

whileattemptingtofreeajammedcondition.

6. Do not use this stapler for fastening electrical

cables. Itisnotdesignedforelectriccableinstal-

lationandmaydamagetheinsulationofelectric

cablestherebycausingelectricshockorre

hazards.

7. Keep hands and feet away from the ejection

port area.

8. Follow instruction for lubricating and chang-

ing accessories.

9. Always remove the battery cartridge before

loading the fasteners, adjustment, inspection,

maintenance or after operation is over.

10. Make sure no one is nearby before operation.

Never attempt to drive fasteners from both the

inside and outside of wall at the same time.

Fasteners may rip through and/or y o, pre-

senting a grave danger.

11. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

when working in high locations.

12. Check walls, ceilings, oors, roong and

the like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused by

stapling into live wires, conduits or gas pipes.

13. Use only fasteners specied in this manual.

The use of any other fasteners may cause

malfunction of the tool.

14. Do not tamper with the tool or attempt to use it

for other than driving fasteners.

15. Do not operate the tool without fasteners. It

shortens the service life of the tool.

16. Stop driving operations immediately if you

notice something wrong or out of the ordinary

with the tool.

17. Never fasten into any materials which may

allow the fastener to puncture and y through

as a projectile.

18. Never actuate the switch trigger and contact

element at the same time until you are pre-

pared to fasten workpieces. Allow the work-

piece to depress the contact element. Never

defeat its purpose by securing the contact

element back or by depressing it by hand.

8ENGLISH

19. Never tamper with the contact element. Check

the contact element frequently for proper

operations.

20. Always remove fasteners from the tool when

not in use.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

Forcommercialtransportse.g.bythirdparties,

forwardingagents,specialrequirementonpack-

aging and labeling must be observed.

Forpreparationoftheitembeingshipped,consult-

inganexpertforhazardousmaterialisrequired.

Pleasealsoobservepossiblymoredetailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmaycauseheating,catchingre,

burstandmalfunctionofthetoolorbatterycar-

tridge,resultinginburnsorpersonalinjury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines.Itmayresultinamalfunction

orbreakdownofthetoolorbatterycartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Useofnon-genuineMakitabatteries,orbatteriesthat

havebeenaltered,mayresultinthebatterybursting

causingres,personalinjuryanddamage.Itwill

alsovoidtheMakitawarrantyfortheMakitatooland

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

9ENGLISH

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

withalittleclick.Ifyoucanseetheredindicatoras

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

not being inserted correctly.

Indicating the remaining battery

capacity

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

lightupforafewseconds.

►Fig.2: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE:Dependingontheconditionsofuseandthe

ambienttemperature,theindicationmaydierslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsopowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placedunderoneofthefollowingconditions:

Overload protection

Whenthetool/batteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetool

automaticallystops.Inthissituation,turnthetoolo

and stop the application that caused the tool to become

overloaded.Thenturnthetoolontorestart.

NOTE:Clearpossiblecausesforoverload(e.g.,

clearingjamsinsidethemagazine),andthentry

restartingthetool.Ifnoimprovementhasbeenmade,

ask your local Makita Service Center.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetool/batterycool

beforeturningthetoolonagain.

10 ENGLISH

NOTE:Thelampstartsashingwhenthetool/battery

becomes overheated or detects an error during driv-

ing operation. Allow the tool and battery together (with

the battery installed in the tool) to cool down until

thelampstopsashing.Ifnoimprovementhasbeen

madeaftercooling,askyourlocalMakitaService

Center.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically.Inthiscase,removethebatteryfromthe

tool and charge the battery.

Protections against other causes

Protectionsystemisalsodesignedforothercauses

that could damage the tool and allows the tool to stop

automatically.Takeallthefollowingstepstoclearthe

causes,whenthetoolhasbeenbroughttoatemporary

halt or stop in operation.

1. Turnthetoolo,andthenturnitonagainto

restart.

2. Chargethebattery(ies)orreplaceit/themwith

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

Ifnoimprovementcanbefoundbyrestoringprotection

system,thencontactyourlocalMakitaServiceCenter.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the “OFF” position when released.

CAUTION: When not operating the tool,

depress the trigger-lock button from B side to

lock the switch trigger in the “OFF” position.

Topreventtheswitchtriggerfromaccidentallypulled,

the trigger-lock button is provided.

Topulltheswitchtrigger,depressthetrigger-lockbutton

fromAside.

Afteruse,alwayspressinthetrigger-lockbuttonfrom

B side.

►Fig.3: 1.Trigger-lockbutton2. Switch trigger

Adjusting depths of stapling

WARNING: Always make sure that your n-

gers are not placed on the switch trigger or the

contact element and that the battery cartridge and

staples are removed before adjusting the depths

of stapling.

Depthsofstaplingcanbechangedbyliftingandlower-

ingthedepthguideatthebottomofthetool.Turnthe

adjusterinthedirectionshownintheguretoadjustthe

depth guide position. Settings toggle through 5 ranges

ofdepthin0.6mmincrements.

►Fig.4: 1.Adjuster2. Depth guide

Lighting up the lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggeroractuatethecontactelement

tolightupthelamp.Thelampremainslitforupto

15 minutes while pulling the switch trigger or actuating

thecontactelement.Thelampgoesoutapproximately

10secondsafterreleasingtheswitchtriggerandthe

contact element.

►Fig.5: 1. Lamp

NOTICE: Use a dry cloth to wipe the dirt o the

lens of the lamp. Be careful not to scratch the lens

of lamp, or it may lower the illumination.

NOTICE: The tool may not re staples after the

battery becomes low on power even while the

lamp remains lit. In this case, charge the battery

cartridge.

NOTICE: The lamp starts ashing when the tool/

battery becomes overheated or detects an error

during driving operation. Take the following steps

to clear possible causes.

1. Keep the battery installed in the tool, and let

the tool and battery together cool down until

the lamp stops ashing.

2. Remove the battery cartridge from the tool,

and then clear jams inside the magazine.

If the tool does not restart after recovery, ask your

local Makita Service Center.

ASSEMBLY

CAUTION: Always make sure that your

ngers are not placed on the switch trigger or

the contact element and the battery cartridge is

removed before carrying out any work on the

stapler.

Staples

CAUTION: Do not use deformed, rusted, and

corroded staple strips. Use staples specied in

this manual.Usingstaplesotherthanthosespecied

maycausestaplejammingandbreakageofthetool.

NOTICE: Handle the staples and their box care-

fully. If the staples have been handled roughly,

they may be bent out of shape, causing poor

staple feed or jamming.

NOTICE: Avoid storing the staples in a very

humid or hot place or place exposed to direct

sunlight.

11 ENGLISH

Loading and unloading staples

CAUTION: Always make sure that your n-

gers are not placed on the trigger and the battery

cartridge is removed before loading staples.

Unintentionalringmaycausepersonalinjuriesand

property damage.

CAUTION: After loading staples, make sure

that the sub magazine is surely closed. Falling

staplesoutofthemagazinemaycauseaninjuryto

theoperatororbystander,especiallywhenworkingin

high locations.

1. Turnthelockingleverinthedirectionshowninthe

gure,thenslidethesubmagazineopen.

►Fig.6: 1. Locking lever 2. Sub magazine

2. Load staples into the main magazine with their

feetfacingup.

►Fig.7: 1. Staples 2. Main magazine

NOTICE: Load staples in the correct direction

as illustrated.Thesubmagazinecannotbeclosed

securelyifyouloadstaplesinwrongdirection.

NOTICE: Avoid loading strips of fewer staples,

especially when using staples in short lengths. It

maycausejamminganddamagestothetool.

NOTICE: Prepare strips of staples of the same

length and size before loading multiple strips of

staples at one time.

Should strips of dierent dimensions be installed

in the magazine, discharge all the mismatched

staples in the magazine onto the junk material.

3. Return the sub magazine to the original position

and lock it in place with the locking lever.

Toremovethestaples,turnthelockingleverandslide

thesubmagazineopen.Takeoutthestaplesfromthe

magazine.

Nose adapter

CAUTION: Always make sure that your

ngers are not placed on the switch trigger or

the contact element and the battery cartridge is

removed before installing the nose adapter.

Whenringstaplesonthematerialwitheasily-marred

surfaces,attachthenoseadapterontothecontacttop.

You can store the nose adapter in the holder at the back

endofthemagazinetokeepitfrombeinglost.

►Fig.8: 1. Nose adapter 2. Holder 3. Contact top

Hook

CAUTION: When installing the hook, always

secure it with the screw rmly.Ifnot,thehook

maycomeofromthetoolandresultinthepersonal

injury.

CAUTION: Use the hanging/mounting parts

for their intended purposes only.Usingforunin-

tended purpose may cause accident or personal

injury.

CAUTION: Do not hang the hook from the

waist belt.Droppingthestapler,whichiscausedby

thehookaccidentallycomingoutofplace,maycause

unintentionalringandresultinpersonalinjuries.

►Fig.9

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.

Toinstallthehook,insertitintoagrooveinthetool

housing on either side and then secure it with a screw.

Toremove,loosenthescrewandthentakeitout.

►Fig.10: 1. Groove 2. Hook 3. Screw

OPERATION

Testing safety system

WARNING: Make sure all safety systems are

in working order before operation. Failure to do

so may cause personal injuries.

►Fig.11: 1.Trigger-lockbutton2. Switch trigger

3. Contact element 4. Magazine

Testsafetysystemasfollowsforpossiblefaultbefore

operation.

1. Unloadstaplesfromthetoolandkeepthemaga-

zine opened.

2. Install the battery cartridge and release the trigger

lock.

3. Pulltheswitchtriggerwithouttouchingthecontact

element against the material.

4. Touchthecontactelementagainstthematerial

without pulling the switch trigger.

Ifthetoolworksincase3or4describedabove,safety

systemisnotfunctioningproperly.Stopusingthetool

immediately and ask your local Makita Service Center.

12 ENGLISH

Driving staples

WARNING: Do not use this stapler for fasten-

ing electrical cables. Itisnotdesignedforelectric

cableinstallationandmaydamagetheinsulationof

electriccablestherebycausingelectricshockorre

hazards.

WARNING: Continue to place the contact

element rmly on the material until the staple is

driven completely.Unintentionalringmaycause

personalinjuries.

WARNING: Keep your face away from the tool

when operating the tool.Failuretodosomaycause

injury.

CAUTION: Hold the tool rmly during

operation.

CAUTION: Do not use the tool beyond the

continuous operating time allowed. It otherwise

may cause damages to the tool resulting in personal

injury.

NOTICE: The tool will not restart fastening

after ve seconds no switch operation while the

contact element is placed on the workpiece. Pull

the contact element free from the workpiece and

reposition it in place to restart fastening.

Youcanoperatethetoolineitherwayof“single

sequentialactuation”or“contactactuation”.

Single sequential actuation:

Inthismode,youcandriveonestaplebyonesequen-

tial operation.

1. Release the trigger lock.

2. Placeatthecontactelementonthematerial.

3. Holdthedepthguidermlyagainstthematerial.

►Fig.12: 1.Trigger-lockbutton2. Contact element

3. Depth guide

4. Pulltheswitchtriggerfullytodriveastaple.

►Fig.13: 1. Switch trigger

5. Releaseyourngerfromtheswitchtriggerbefore

movingthecontactelementfromthematerial.

Youcanalsosequentiallydrivestaplesbypullingthe

switch trigger while dragging the tool to the next area

with the contact element pressed against the material.

►Fig.14

Contact actuation:

Inthismode,youcandrivestaplesconsecutively.

1. Release the trigger lock.

2. Pulltheswitchtrigger.

►Fig.15: 1.Trigger-lockbutton2. Switch trigger

3. Placeatthecontactelementonthematerialto

drive a staple.

4. Move the tool to the next areas with the switch

triggerpulled,andplaceatthecontactelementonthe

materialtodrivefollowingstaples.

►Fig.16: 1. Switch trigger 2. Contact element

Iftheheadofthestapleremainsabovetheworkpiece

surface,drivethestaplewhileholdingthestaplerhead

rmlyagainsttheworkpiece.

►Fig.17

NOTE:Iftheheadofthestaplestillremainsabove

theworkpieceevenyouholdthestaplerhead,

thematerialmaynotbesuitableforthestapler.

Continuinguseofthestapleronsuchmaterialmay

resultinadamagetothestaplerdriverand/orstapler

jamming.

Anti dry re mechanism

WARNING: Always make sure that your

ngers are not placed on the switch trigger or

the contact element and the battery cartridge is

removed before loading the staples.

As all the staples loaded in the magazine become used

up,thetoolwillautomaticallystopringtominimize

damagefromdryringandenhancesafety.

Insertanewstripofstaplesinthemagazinebefore

restarting operation.

Checking remaining staples

Learn remaining staples in the magazine through the

sightwindow.Thepusherappearsinthewindowand

movestowardstheringopeningastheamountof

remaining staples becomes smaller.

►Fig.18: 1. Sight window 2. Staples 3.Pusher

Removing jammed staples

WARNING: Always make sure that the trigger

is released, and the battery cartridge and staples

are removed before removing jammed staples.

CAUTION: Do not remove the jammed staples

with bare hands.Thestaplesmayjumpoutofthe

magazineandcauseaninjury.

1. Turnthelockingleverinthedirectionshowninthe

gure,thenslidethesubmagazineopen.

2. Removeallthestaplesleftinthemainmagazine.

3. Clearjammedstaplesfromtheringopening.

►Fig.19: 1. Locking lever 2. Sub magazine 3. Main

magazine 4.Firingopening

4. Placethestripofstaplesbackinthemagazine,

and close the sub magazine securely.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers,alwaysusingMakitareplacementparts.

Cleaning magazine

Cleantheinsideofthemagazineatregularintervals.

Wipeoanydirt,dust,woodchips,andstapleglue

accumulated inside the magazine.

►Fig.20

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessoriesorattachmentsmightpresentariskof

injurytopersons.Onlyuseaccessoryorattachment

foritsstatedpurpose.

Ifyouneedanyassistanceformoredetailsregard-

ingtheseaccessories,askyourlocalMakitaService

Center.

• Staples

• Makitagenuinebatteryandcharger

NOTE: Some items in the list may be included in the

toolpackageasstandardaccessories.Theymay

dierfromcountrytocountry.

ENGLISH

中文简体

中文简体 (原本)

规格

型号： ST001G ST002G

马钉宽度 4 mm 10 mm

适用的马钉长度 13 mm - 25 mm

马钉盒容量 100 个

尺寸（长 × 宽 × 高）*1*2 269 mm × 86 mm × 216 mm

额定电压 D.C. 36 V - 40 V（最大）

净重 2.5 - 3.7 kg

*1 不带挂钩

*2 电池型号 BL4025

• 生产者保留变更规格不另行通知之权利。

• 规格和电池组可能因销往国家之不同而异。

• 重量因附件（包括电池组）而异。根据EPTA-Procedure01/2014，最重与最轻的组合见

表格。

适用电池组和充电器

电池组 BL4020*/BL4025*/BL4040*/BL4050F/

BL4080F

*：建议使用的电池

充电器 DC40RA/DC40RB/DC40RC

• 部分以上所列电池组和充电器是否适用视用户所在地区而异。

警告：请仅使用以上所列电池组和充电器。使用其他类型的电池组或充电器可能会导致

人身伤害和/或失火。

符号

以下显示本设备可能会使用的符号。在使用

工具之前，请务必理解其含义。

阅读使用说明书。

Ni-MH

Li-ion 仅限于欧盟国家

由于本设备中包含有害成分，

因此废弃的电气和电子设备、

蓄电池和普通电池可能会对环

境和人体健康产生负面影响。

请勿将电气和电子工具或电池

与家庭普通废弃物放在一起处

置！

根据欧洲关于废弃电气电子设

备、蓄电池和普通电池、废弃

的蓄电池和普通电池的指令及

其国家层面的修订法案，废弃

的电气设备、普通电池和蓄电

池应当单独存放并递送至城市

垃圾收集点，根据环保法规进

行处置。

此规定由标有叉形标志的带轮

垃圾桶符号表示。

中文简体

用途

本工具用于将马钉钉入木材等建筑材料。

安全警告

电动工具通用安全警告

警告

阅读随电动工具提供的所有安全警

告、说明、图示和规定。不遵照以下所列说

明会导致电击、着火和／或严重伤害。

保存所有警告和说明书以备查

阅。

警告中的术语“电动工具”是指市电驱动（有

线）电动工具或电池驱动（无线）电动工具。

工作场地的安全

1. 保持工作场地清洁和明亮。杂乱和黑暗

的场地会引发事故。

2. 不要在易爆环境，如有易燃液体、气体

或粉尘的环境下操作电动工具。电动工

具产生的火花会点燃粉尘或气体。

3. 操作电动工具时，远离儿童和旁观者。

注意力不集中会使你失去对工具的控制。

电气安全

1. 电动工具插头必须与插座相配。绝不能

以任何方式改装插头。需接地的电动工

具不能使用任何转换插头。未经改装的

插头和相配的插座将降低电击风险。

2. 避免人体接触接地表面，如管道、散热

片和冰箱。如果你身体接触接地表面会

增加电击风险。

3. 不得将电动工具暴露在雨中或潮湿环境

中。水进入电动工具将增加电击风险。

4. 不得滥用软线。绝不能用软线搬运、拉

动电动工具或拔出其插头。使软线远离

热源、油、锐边或运动部件。受损或缠

绕的软线会增加电击风险。

5. 当在户外使用电动工具时，使用适合户

外使用的延长线。适合户外使用的电线

将降低电击风险。

6. 如果无法避免在潮湿环境中操作电动工

具，应使用带有剩余电流装置（RCD）

保护的电源。RCD的使用可降低电击风

险。

7. 电动工具会产生对用户无害的电磁场

（EMF）。但是，起搏器和其他类似医

疗设备的用户应在操作本电动工具前咨

询其设备的制造商和／或医生寻求建议。

人身安全

1. 保持警觉，当操作电动工具时关注所从

事的操作并保持清醒。当你感到疲倦，

或在有药物、酒精或治疗反应时，不要

操作电动工具。在操作电动工具时瞬间

的疏忽会导致严重人身伤害。

2. 使用个人防护装置。始终佩戴护目镜。

防护装置，诸如适当条件下使用防尘面

具、防滑安全鞋、安全帽、听力防护等

装置能减少人身伤害。

3. 防止意外起动。在连接电源和 /或电池包、

拿起或搬运工具前确保开关处于关断位

置。手指放在开关上搬运工具或开关处

于接通时通电会导致危险。

4. 在电动工具接通之前，拿掉所有调节钥

匙或扳手。遗留在电动工具旋转零件上

的扳手或钥匙会导致人身伤害。

5. 手不要过分伸展。时刻注意立足点和身

体平衡。这样能在意外情况下能更好地

控制住电动工具。

6. 着装适当。不要穿宽松衣服或佩戴饰品。

让你的头发和衣服远离运动部件。宽松

衣服、佩饰或长发可能会卷入运动部件。

7. 如果提供了与排屑、集尘设备连接用的

装置，要确保其连接完好且使用得当。

使用集尘装置可降低尘屑引起的危险。

8. 不要因为频繁使用工具而产生的熟悉感

而掉以轻心，忽视工具的安全准则。某

个粗心的动作可能在瞬间导致严重的伤

害。

9. 使用电动工具时请始终佩带护目镜以免伤

害眼睛。护目镜须符合美国ANSI Z87.1、

欧洲EN 166或者澳大利亚／新西兰的

AS/NZS 1336的规定。在澳大利亚／

新西兰，法律要求佩带面罩保护脸部。

雇主有责任监督工具操作者和其他近工

作区域人员佩带合适的安全防护设备。

中文简体

电动工具使用和注意事项

1. 不要勉强使用电动工具，根据用途使用

合适的电动工具。选用合适的按照额定

值设计的电动工具会使你工作更有效、

更安全。

2. 如果开关不能接通或关断电源，则不能

使用该电动工具。不能通过开关来控制

的电动工具是危险的且必须进行修理。

3. 在进行任何调节、更换附件或贮存电动

工具之前，必须从电源上拔掉插头和/或

卸下电池包（如可拆卸）。这种防护性

的安全措施降低了电动工具意外起动的

风险。

4. 将闲置不用的电动工具贮存在儿童所及

范围之外，并且不允许不熟悉电动工具

和不了解这些说明的人操作电动工具。

电动工具在未经培训的使用者手中是危

险的。

5. 维护电动工具及其附件。检查运动部件

是否调整到位或卡住，检查零件破损情

况和影响电动工具运行的其他状况。如

有损坏，应在使用前修理好电动工具。

许多事故是由维护不良的电动工具引发

的。

6. 保持切削刀具锋利和清洁。维护良好地

有锋利切削刃的刀具不易卡住而且容易

控制。

7. 按照使用说明书，并考虑作业条件和要

进行的作业来选择电动工具、附件和工

具的刀头等。将电动工具用于那些与其

用途不符的操作可能会导致危险情况。

8. 保持手柄和握持表面干燥、清洁，不得

沾有油脂。在意外的情况下，湿滑的手

柄不能保证握持的安全和对工具的控制。

9. 使用本工具时，请勿佩戴可能会缠结的

布质工作手套。布质工作手套卷入移动

部件可能会造成人身伤害。

电池式工具使用和注意事项

1. 仅使用生产者规定的充电器充电。将适

用于某种电池包的充电器用到其他电池

包时可能会发生着火危险。

2. 仅使用配有专用电池包的电动工具。使

用其他电池包可能会产生伤害和着火危

险。

3. 当电池包不用时，将它远离其他金属物

体，例如回形针、硬币、钥匙、钉子、

螺钉或其他小金属物体，以防电池包一

端与另一端连接。电池组端部短路可能

会引起燃烧或着火。

4. 在滥用条件下，液体可能会从电池组中

溅出；应避免接触。如果意外碰到液体，

用水冲洗。如果液体碰到了眼睛，还应

寻求医疗帮助。从电池中溅出的液体可

能会发生腐蚀或燃烧。

5. 不要使用损坏或改装过的电池包或工具。

损坏或改装过的电池组可能呈现无法预

测的结果，导致着火、爆炸或伤害。

6. 不要将电池包暴露于火或高温中。电池

包暴露于火或高于130 ℃的高温中可能

导致爆炸。

7. 遵循所有充电说明。不要在说明书中指

定的温度范围之外给电池包或电动工具

充电。不正确或在指定的温度范围外充

电可能会损坏电池和增加着火的风险。

维修

1. 让专业维修人员使用相同的备件维修电

动工具。这将保证所维修的电动工具的

安全。

2. 决不能维修损坏的电池包。电池包仅能

由生产者或其授权的维修服务商进行维

修。

3. 上润滑油及更换附件时请遵循本说明书

指示。

充电式马钉枪安全警告

1. 始终假定工具中含有紧固件。粗心操作

马钉枪会导致紧固件意外射出并造成人

身伤害。

2. 请勿将工具对准自身或近旁任何人。意

外扣动工具会弹出紧固件，从而造成人

身伤害。

3. 将工具牢固抵住工件之前，请勿启动工

具。如果工具未抵住工件，紧固件可能

会偏离目标紧固位置。

4. 当紧固件卡在工具中时，请将工具从电

源处断开。如果插入其电源，拆卸卡住

的紧固件时，马钉枪可能会意外启动。

5. 拆卸卡住的紧固件时，请务必小心操作。

紧固机构可能会处于受压状态，当尝试

将紧固件从受卡状态中释放时，它可能

会强力弹出。

6. 请勿使用该马钉枪固定电缆。其并非设

计用于电缆安装，否则可能会损坏电缆

的绝缘材料，从而引发触电或火灾危险。

7. 手和脚勿靠近弹射口区域。

8. 根据说明进行润滑和更换附件。

9. 务必在装载紧固件，执行调整、检查和

保养前或使用之后拆下电池组。

中文简体

10. 操作工具前，请确保近旁无人。切勿尝

试从墙壁内外两侧同时驱动紧固件。紧

固件可能会穿透和／或飞出墙壁，造成

伤亡事故。

11. 使用工具时，请注意立足稳固并保持平

衡。在高处作业时，要确保下方无人。

12. 仔细检查墙壁、天花板、地板、屋面等

类似位置以避免因钉入带电电线、导管

或煤气管道而导致触电、煤气泄露和爆

炸等。

13. 仅可使用本说明书指定的紧固件。使用

任何其他紧固件可能会导致工具故障。

14. 请勿改装本工具，或将其用作驱动紧固

件以外的用途。

15. 未安装紧固件时，请勿操作本工具。这

会缩短工具使用寿命。

16. 如果注意到工具出现故障或异常情况，

请立即停止打钉操作。

17. 切勿将紧固件钉入可能会使紧固件穿透

并射出的任何材料。

18. 准备好紧固工件之前，切勿同时启动开

关扳机和接触部件。使工件按压接触部

件。切勿将接触部件固定在回缩位置或

手动按压接触部件而影响其用途。

19. 切勿改装接触部件。时常检查接触部件

以确保正常操作。

20. 不使用时，务必从工具上拆下紧固件。

请保留此说明书。

警告：请勿为图方便或因对产品足够熟

悉（由于重复使用而获得的经验）而不严格

遵循相关产品安全规则。使用不当或不遵循

使用说明书中的安全规则会导致严重的人身

伤害。

电池组的重要安全注意事项

1. 在使用电池组之前，请仔细通读所有的

说明以及（1）电池充电器，（2）电

池，以及（3）使用电池的产品上的警

告标记。

2. 切勿拆卸或改装电池组。否则可能引起

火灾、过热或爆炸。

3. 如果机器运行时间变得过短，请立即停

止使用。否则可能会导致过热、起火甚

至爆炸。

4. 如果电解液进入您的眼睛，请用清水将

其冲洗干净并立即就医。否则可能会导

致视力受损。

5. 请勿使电池组短路：

(1) 请勿使任何导电材料碰触到端子。

(2) 避免将电池组与其他金属物品如钉

子、硬币等放置在同一容器内。

(3) 请勿将电池组置于水中或使其淋雨。

电池短路将产生大的电流，导致过热，并

可能导致起火甚至击穿。

6. 请勿在温度可能达到或超过50°C（122°F）

的场所存放以及使用工具和电池组。

7. 即使电池组已经严重损坏或完全磨损，

也请勿焚烧电池组。电池组会在火中爆

炸。

8. 请勿对电池组射钉，或者切削、挤压、

抛掷、掉落电池组，又或者用硬物撞击

电池组。否则可能引起火灾、过热或爆

炸。

9. 请勿使用损坏的电池。

10. 本工具附带的锂离子电池需符合危险品

法规要求。

第三方或转运代理等进行商业运输时，

应遵循包装和标识方面的特殊要求。

有关运输项目的准备作业，咨询危险品

方面的专业人士。同时，请遵守可能更

为详尽的国家法规。

请使用胶带保护且勿遮掩表面的联络信

息，并牢固封装电池，使电池在包装内

不可动。

11. 丢弃电池组时，需将其从工具上卸下并

在安全地带进行处理。关于如何处理废

弃的电池，请遵循当地法规。

12. 仅将电池用于Makita（牧田）指定的产

品。将电池安装至不兼容的产品会导致

起火、过热、爆炸或电解液泄漏。

13. 如长时间未使用工具，必须将电池从工

具内取出。

14. 使用工具期间以及使用工具之后，电池

组温度可能较高易引起灼伤或低温烫伤。

处理高温电池组时请小心操作。

15. 在使用工具后请勿立即触碰工具的端子，

否则可能引起灼伤。

16. 避免锯屑、灰尘或泥土卡入电池组的端

子、孔口和凹槽内。否则可能会导致过

热、着火、爆炸和工具/电池组故障，导

致烫伤或人身伤害。

17. 除非工具支持在高压电源线路附近使用，

否则请勿在高压电源线路附近使用电池

组。否则可能导致工具或电池组故障或

失常。

中文简体

18. 确保电池远离儿童。

请保留此说明书。

小心：请仅使用Makita（牧田）原装电

池。使用非Makita（牧田）原装电池或经过

改装的电池可能会导致电池爆炸，从而造成

火灾、人身伤害或物品受损。同时也会导致

牧田工具和充电器的牧田保修服务失效。

保持电池最大使用寿命的提示

1. 在电池组电量完全耗尽前及时充电。发

现工具电量低时，请停止工具操作，并

给电池组充电。

2. 请勿对已充满电的电池组重新充电。过

度充电将缩短电池的使用寿命。

3. 请在10 °C - 40 °C（50 °F - 104 °F）的

室温条件下给电池组充电。请在灼热的

电池组冷却后再充电。

4. 不使用电池组时，请将其从工具或充电

器上拆除。

5. 如果电池组长时间（超过六个月）未使

用，请给其充电。

功能描述

小心：调节或检查工具功能之前，请务

必关闭工具的电源并取出电池组。

安装或拆卸电池组

小心：安装或拆卸电池组之前，请务必

关闭工具电源。

小心：安装或拆卸电池组时请握紧工具

和电池组。否则它们可能从您的手中滑落，导

致工具和电池组受损，甚至造成人身伤害。

► 图片1: 1. 红色指示器 2. 按钮 3. 电池组

拆卸电池组时，按下电池组前侧的按钮，同

时将电池组从工具中抽出。

安装电池组时，要将电池组上的舌簧与外罩

上的凹槽对齐，然后推滑到位。将其完全插

入到位，直到锁定并发出咔哒声为止。若能

看到图示中的红色指示器，则说明未完全锁

紧。

小心：务必完全装入电池组，直至看不

见红色指示器为止。否则，它可能会从工具

中意外脱落，从而造成自身或他人受伤。

小心：请勿强行安装电池组。如果电池

组难以插入，可能是插入方法不当。

显示电池的剩余电量

按电池组上的CHECK（查看）按钮可显示电

池剩余电量。指示灯将亮起数秒。

► 图片2: 1. 指示灯 2.CHECK（查看）按钮

指示灯剩余电量

点亮熄灭闪烁

75%至

100%

50%至

75%

25%至

50%

0%至

25%

给电池

充电。

电池可

能出现

故障。

注：在不同的使用条件及环境温度下，指

示灯所示电量可能与实际情况略有不同。

注：当电池保护系统启动时，第一个（最

左侧）指示灯将闪烁。

工具／电池保护系统

本工具配备有工具／电池保护系统。该系统

可自动切断电机电源以延长工具和电池寿命。

作业时，如果工具或电池处于以下情况，工

具将会自动停止运转。

过载保护

以导致异常高电流的方式操作工具／电池时，

工具会自动停止运转。在这种情况下，请关

闭工具并停止导致工具过载的应用程序。然

后开启工具以重新启动。

中文简体

注：清除可能的过载原因（例如清除钉盒内

侧卡住的钉子），然后尝试重新启动工具。如

果仍无改善，请咨询当地的Makita（牧田）

维修服务中心。

过热保护

工具／电池过热时，工具会自动停止。在这

种情况下，请待工具／电池冷却后再开启工

具。

注：打钉操作期间，工具／电池变得过热或

检测到错误时，照明灯开始闪烁。使工具和

电池一起（电池安装在工具内的状态下）冷

却，直至照明灯停止闪烁。如果冷却后仍无

改善，请咨询当地的Makita（牧田）维修服

务中心。

过放电保护

电池电量不足时，本工具自动停止运转。此

时，请取出工具中的电池并予以充电。

其他原因防护

保护系统还适用于其他可能导致工具受损的

情况，从而使工具自动停止运转。工具暂时

或中途停止工作时，执行以下所有步骤以排

除异常原因。

1. 关闭工具，然后再次重新启动。

2. 给电池充电或更换为充电电池。

3. 请等待工具和电池冷却。

如果保护系统恢复后仍无改善，请联络当地

的Makita（牧田）维修服务中心。

开关操作

小心：在将电池组插入工具之前，请务

必检查开关扳机是否能扣动自如，松开时能

否退回至“OFF”（关闭）位置。

小心：不操作工具时，从B侧按下扳机

锁按钮，将开关扳机锁定在“OFF”（关闭）

位置。

为避免使用者不小心扣动开关扳机，本工具

采用扳机锁按钮。

要扣动开关扳机，请从A侧按下扳机锁按钮。

使用之后，请务必从B侧按下扳机锁按钮。

► 图片3: 1. 扳机锁按钮 2. 开关扳机

调节打钉深度

警告：调节打钉深度前，请务必确保未

将手指放置在开关扳机或接触部件上，并已

取出电池组和马钉。

通过提升和降低工具底部的深度导板来改变

打钉深度。按图中所示方向旋转调节器以调

节深度导板的位置。以0.6 mm为增量在5个

深度范围内进行切换设定。

► 图片4: 1. 调节器 2. 深度导板

点亮照明灯

小心：请勿直视灯光或光源。

扣动开关扳机或启动接触部件，以点亮照明

灯。在扣动开关扳机或启动接触部件时，此

照明灯将保持常亮，时间最长为15分钟。松

开开关扳机和接触部件约10秒后，此照明灯

会熄灭。

► 图片5: 1. 照明灯

注意：请使用干布擦拭灯头灰。注意不要

刮花灯头，否则会降低亮度。

注意：当电池电量变低时，即使照明灯保

持常亮，工具也可能无法打钉。在这种情况

下，请给电池组充电。

注意：打钉操作期间，工具／电池变得过

热或检测到错误时，照明灯开始闪烁。执行

以下步骤以清除可能的原因。

1. 保持电池安装在工具内的状态，使工具

和电池一起冷却，直至照明灯停止闪

烁。

2. 从工具中取出电池组，然后清除钉盒内

侧卡住的钉子。

如果复原后工具不重启，请咨询当地的

Makita（牧田）维修服务中心。

装配

小心：对钉枪进行任何操作前，请务必

确保未将手指放置在开关扳机或接触部件

上，并已取出电池组。

中文简体

马钉

小心：请勿使用变形、生锈和有腐蚀的

钉条。请使用本说明书中指定的马钉。使用

其他非指定的马钉，可能会导致卡钉和工具

破损。

注意：小心操作马钉和钉盒。如果处理不

当，可能会导致马钉弯折变形，造成无法正

常出钉或导致卡钉。

注意：避免将马钉存放在非常潮湿、高温

或阳光直射的位置。

装载和卸载马钉

小心：装载马钉前，请务必确保未将手

指放置在扳机上，并已取出电池组。意外打

钉可能会造成人身伤害和财产损失。

小心：装入马钉后，确保副钉盒已关

闭。马钉从钉盒中跌落可能会对操作者或旁

观者造成伤害，尤其是在高处作业时。

1. 按图中所示方向转动锁定杆，然后滑动

打开副钉盒。

► 图片6: 1. 锁定杆 2. 副钉盒

2. 使钉脚朝上将马钉装入主钉盒。

► 图片7: 1. 马钉 2. 主钉盒

注意：如图所示以正确的方向装入马钉。

如果以错误方向装入马钉，副钉盒无法牢固

关闭。

注意：避免装入马钉较少的钉条，尤其是

使用较短的马钉时。可能会导致卡钉和工具

受损。

注意：一次性装入多个马钉条前，请准备

相同长度和尺寸的马钉条。

万一钉盒中装入了不同尺寸的钉条，请在废

料上打出钉盒中所有不匹配的马钉。

3. 将副钉盒恢复至原来位置，然后用锁定

杆将其锁定到位。

拆卸马钉时，转动锁定杆后，滑动打开副钉

盒。从钉盒中取出马钉。

枪头适配器

小心：安装枪头适配器前，请勿将手指

放置在开关扳机或接触部件上，并取出电池

组。

当在表面易损的材料上打马钉时，请先将枪

头适配器安装至接触顶点。

您可以将枪头适配器存放在钉盒后端的固定

器中，以防丢失。

► 图片8: 1. 枪头适配器 2. 固定器 3. 接触

顶点

挂钩

小心：安装挂钩时，务必使用螺丝将其

固定。否则挂钩可能会脱离工具，导致人身

伤害。

小心：悬挂／安装部件只能用于预期用

途。用作其他用途可能会引发意外或造成人

身伤害。

小心：请勿将挂钩挂在腰带上。因挂钩

意外脱落而导致马钉枪掉落，可能会造成意

外打钉并导致人身伤害。

► 图片9

挂钩便于临时悬挂工具。可安装在工具的任

一侧。

要安装挂钩，请将其插入工具外壳上任一侧

的凹槽中，然后用螺丝加以紧固。要拆卸挂

钩，请将螺丝拧松，然后将其取出。

► 图片10: 1. 凹槽 2. 挂钩 3. 螺丝

操作

测试安全系统

警告：请在操作前确保所有的安全系统

处于工作状态。否则可能会导致人身伤害。

► 图片11: 1. 扳机锁按钮 2. 开关扳机 3. 接

触部件 4. 钉盒

操作前按如下步骤测试安全系统，查找可能

存在的故障。

1. 从工具中取出马钉并保持钉盒打开。

2. 安装电池组并释放扳机锁。

3. 在接触部件未抵住材料的情况下扣动开

关扳机。

4. 在不扣动开关扳机的情况下，使接触部

件抵住材料。

如果工具在以上3或4的情况下运转，则安全

系统不正常工作。请立即停止使用工具，并

咨询当地的Makita（牧田）维修服务中心。

ページを読み込んでいます...

Makita ST001G ユーザーマニュアル

関連論文