Makita DDF489 ユーザーマニュアル

DDF489

EN Cordless Driver Drill INSTRUCTION MANUAL 4

ZHCN 充电式起子电钻使用说明书 12

ID Bor Obeng Tanpa Kabel PETUNJUK PENGGUNAAN 21

MS Gerudi Pandu Tanpa Wayar MANUAL ARAHAN 30

VI Máy Khoan Và Vặn Vít Cầm

Tay Hoạt Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 39

TH   48

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

4ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DDF489

Drilling capacities Steel 13 mm

Wood Auger bit: 38 mm

Self-feed bit: 51 mm

Hole saw: 51 mm

Fastening capacities Wood screw 10 mm x 90 mm

Machine screw M6

No load speed (RPM) High (2) 0 - 1,800 min-1

Low (1) 0 - 550 min-1

Overall length 174 mm

Rated voltage D.C. 18 V

Net weight 1.8 - 2.5 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

estcombinations,accordingtoEPTA-Procedure01/2014,areshowninthetable.

Applicable battery cartridge and charger

Batterycartridge BL1815N/BL1820B/BL1830B/BL1840B/BL1850B/BL1860B

Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF/

DC18SH/DC18WC

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

andchargersmaycauseinjuryand/orre.

Symbols

Thefollowingsshowthesymbolswhichmaybeused

fortheequipment.Besurethatyouunderstandtheir

meaning before use.

Read instruction manual.

Ni-MH

Li-ion

OnlyforEUcountries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

andbatteriesmayhaveanegativeimpact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulatorsshouldbestoredseparately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

Thisisindicatedbythesymbolofthe

crossed-out wheeled bin placed on the

equipment.

Intended use

Thetoolisintendedfordrillingandscrewdrivingin

wood, metal and plastic.

5ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instruc-

tions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed

belowmayresultinelectricshock,reand/orserious

injury.

Save all warnings and instruc-

tions for future reference.

Theterm“powertool”inthewarningsreferstoyour

mains-operated(corded)powertoolorbattery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

whichmayignitethedustorfumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

youtolosecontrol.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tricshockifyourbodyisearthedorgrounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

7. Power tools can produce electromagnetic

elds (EMF) that are not harmful to the user.

However, users of pacemakers and other similar

medical devices should contact the maker of their

deviceand/ordoctorforadvicebeforeoperating

this power tool.

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

asadustmask,non-skidsafetyshoes,hardhator

hearing protection used for appropriate conditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.Carryingpowertoolswith

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attachedtoarotatingpartofthepowertoolmay

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.Looseclothes,jewelleryor

long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

cancausesevereinjurywithinafractionofa

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

6ENGLISH

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and o.Anypowertoolthatcannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools.Suchpreventivesafetymeasuresreduce

theriskofstartingthepowertoolaccidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Manyaccidentsarecausedbypoorlymaintained

power tools.

6. Keep cutting tools sharp and clean.Properly

maintained cutting tools with sharp cutting edges

arelesslikelytobindandareeasiertocontrol.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

foroperationsdierentfromthoseintendedcould

result in a hazardous situation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease.Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled.Theentangle-

mentofclothworkglovesinthemovingpartsmay

resultinpersonalinjury.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

onetypeofbatterypackmaycreateariskofre

whenusedwithanotherbatterypack.

2. Use power tools only with specically desig-

nated battery packs.Useofanyotherbattery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.Shortingthebatterytermi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

mayexhibitunpredictablebehaviourresultingin

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

peratureabove130°Cmaycauseexplosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions.Chargingimproperlyorattemperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Never service damaged battery packs. Service

ofbatterypacksshouldonlybeperformedbythe

manufacturer or authorized service providers.

3. Follow instruction for lubricating and chang-

ing accessories.

Cordless driver drill safety warnings

Safety instructions for all operations

1. Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting accessory or fasteners may contact

hidden wiring. Cuttingaccessoryorfasteners

contactinga“live”wiremaymakeexposedmetal

partsofthepowertool“live”andcouldgivethe

operator an electric shock.

2. Always be sure you have a rm footing. Be

sure no one is below when using the tool in

high locations.

3. Hold the tool rmly.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit, the workpiece or

chips immediately after operation; they may be

extremely hot and could burn your skin.

7. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

8. If the drill bit cannot be loosened even you

open the jaws, use pliers to pull it out. In such a

case,pullingoutthedrillbitbyhandmayresultin

injurybyitssharpedge.

9. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

Safety instructions when using long drill bits

1. Never operate at higher speed than the max-

imum speed rating of the drill bit. At higher

speeds,thebitislikelytobendifallowedtorotate

freelywithoutcontactingtheworkpiece,resulting

inpersonalinjury.

7ENGLISH

2. Always start drilling at low speed and with the

bit tip in contact with the workpiece. At higher

speeds,thebitislikelytobendifallowedtorotate

freelywithoutcontactingtheworkpiece,resulting

inpersonalinjury.

3. Apply pressure only in direct line with the bit

and do not apply excessive pressure. Bits can

bend causing breakage or loss of control, resulting

inpersonalinjury.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge.Suchconductmayresultina

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

Forcommercialtransportse.g.bythirdparties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Pleasealsoobservepossiblymoredetailed

national regulations.

Tapeormaskoopencontactsandpackupthe

batteryinsuchamannerthatitcannotmove

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmaycauseheating,catchingre,

burstandmalfunctionofthetoolorbatterycar-

tridge,resultinginburnsorpersonalinjury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines.Itmayresultinamalfunctionor

breakdownofthetoolorbatterycartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

havebeenaltered,mayresultinthebatterybursting

causingres,personalinjuryanddamage.Itwill

alsovoidtheMakitawarrantyfortheMakitatooland

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

8ENGLISH

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3.Batterycartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoras

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2. Check button

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

mayhave

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

thebatteryprotectionsystemworks.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsothepowerto

extendtoolandbatterylife.Thetoolwillautomatically

stopduringoperationifthetoolorbatteryisplaced

under one of the following conditions:

Overload protection

Thisprotectionworkswhenthetool/batteryisoperated

inamannerthatcausesittodrawanabnormallyhigh

current.Inthissituation,turnthetooloandstopthe

application that caused the tool to become overloaded.

Thenturnthetoolontorestart.

Overheat protection

Thisprotectionworkswhenthetoolorbatteryisover-

heated.Inthissituation,letthetoolandbatterycool

before turning the tool on again.

Overdischarge protection

Thisprotectionworkswhentheremainingbattery

capacitygetslow.Inthissituation,removethebattery

fromthetoolandchargethebattery.

Protections against other causes

Protectionsystemisalsodesignedforothercauses

that could damage the tool and allows the tool to stop

automatically.Takeallthefollowingstepstoclearthe

causes,whenthetoolhasbeenbroughttoatemporary

halt or stop in operation.

1. Turnthetoolo,andthenturnitonagainto

restart.

2. Chargethebattery(ies)orreplaceit/themwith

rechargedbattery(ies).

9ENGLISH

3. Letthetoolandbattery(ies)cooldown.

Ifnoimprovementcanbefoundbyrestoringprotection

system,thencontactyourlocalMakitaServiceCenter.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the “OFF” position when released.

►Fig.3: 1. Switch trigger

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ing the switch trigger for about 6 minutes.

Electric brake

Thistoolisequippedwithanelectricbrake.Ifthetool

consistentlyfailstoquicklystopaftertheswitchtrigger

is released, have the tool serviced at a Makita service

center.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.4: 1. Lamp

Pulltheswitchtriggertolightupthelamp.Thelamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: When the tool is overheated, the tool stops

automaticallyandthelampstartsashing.Inthis

case,releasetheswitchtrigger.Thelampturnsoin

one minute.

NOTE:Useadryclothtowipethedirtothelensof

the lamp. Be careful not to scratch the lens of lamp, or

itmaylowertheillumination.

Reversing switch lever action

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch lever

only after the tool comes to a complete stop.

Changing the direction of rotation before the tool

stopsmaydamagethetool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

►Fig.5: 1. Reversing switch lever

Thistoolhasareversingswitchlevertochangethe

direction of rotation. Depress the reversing switch lever

from the A side for clockwise rotation or from the B side

for counterclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Speed change

CAUTION: Always set the speed change lever

fully to the correct position.Ifyouoperatethe

toolwiththespeedchangeleverpositionedhalfway

betweenthe“1”sideand“2”side,thetoolmaybe

damaged.

CAUTION: Do not use the speed change lever

while the tool is running.Thetoolmaybedamaged.

►Fig.6: 1. Speed change lever

Displayed

Number

Speed Torque Applicable

operation

1Low High Heavyload-

ing operation

2High Low Light loading

operation

Tochangethespeed,switchothetoolrst.Pushthe

speedchangelevertodisplay“2”forhighspeedor“1”

for low speed. Be sure that the speed change lever is

set to the correct position before operation.

Ifthetoolspeediscomingdownextremelyduringthe

operationwithdisplay“2”,pushthelevertodisplay“1”

and restart the operation.

Adjusting ring

Youcanselecttheactionmodeandadjustthefastening

torquewiththeadjustingring.

Selecting the action mode

►Fig.7: 1.Adjustingring2. Mark 3. Arrow

Thistoolhastwoactionmodes.

Drillingmode(rotationonly)

1 - 21 Screwdriving mode (rotation

with clutch)

Selectthemodesuitableforyourwork.Turntheadjust-

ingringandalignthemarkthatyouselectwiththe

arrowonthetoolbody.

NOTICE:Alwayssettheringcorrectlytoyour

desiredmodemark.Ifyouoperatethetoolwiththe

ringpositionedhalfwaybetweenthemodemarks,the

toolmaybedamaged.

NOTICE: Do not change the action mode while tool

is rotating.

NOTICE:Ifitisdiculttoslidetheadjustingring,

switch on and run the tool for a second, then stop

thetoolandslidetheadjustingringtoyourdesired

position again.

10 ENGLISH

Adjusting the fastening torque

►Fig.8: 1.Adjustingring2. Mark (1 - 21 graduation)

3. Arrow

Thefasteningtorquecanbeadjustedin21levelsbyturningtheadjustingring.Alignthegraduationswiththearrow

onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat21.

Beforeactualoperation,driveatrialscrewintoyourmaterialorapieceofduplicatematerialtodeterminewhich

torque level is required for a particular application.

Graduation 12345678910 11 12 13 14 15 16 17 18 19 20 21

Machine screw M4 M5 M6

Wood

screw

Soft wood

(e.g. pine)

–ø3.5 x 22 ø4.1x 38 –

Hard wood

(e.g. lauan)

–ø3.5 x 22 ø4.1x 38 –

NOTE:Theadjustingringdoesnotlockwhenthearrowispositionedonlyhalfwaybetweenthegraduations.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

Optional accessory

►Fig.9: 1. Sleeve 2. Close 3. Open

Turnthesleevecounterclockwisetoopenthechuck

jaws.Placethedriverbit/drillbitinthechuckasfar

asitwillgo.Turnthesleeveclockwisetoclosethe

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing side grip (auxiliary handle)

Optional accessory

►Fig.10: 1. Side grip 2. Protrusion 3. Groove 4. Arm

When operating in the heavier load, using the side grip

enablestoholdthetoolmorestably.

Installthesidegripsothattheprotrusionsonthearmt

inthegroovesonthetoolbarrel.Turnthegripclockwise

to secure it.

Dependingtheoperations,youcaninstallthesidegrip

either right or left side of the tool.

Installing hook

WARNING: Use the hanging/mounting parts

for their intended purposes only, e.g., hanging the

tool on a tool belt between jobs or work intervals.

WARNING: Be careful not to overload the

hook as too much force or irregular overburden

may cause damages to the tool resulting in per-

sonal injury.

CAUTION: When installing the hook, always

secure it with the screw rmly. If not, the hook

maycomeofromthetoolandresultinthepersonal

injury.

CAUTION: Make sure to hang the tool

securely before releasing your hold.Insucient

orunbalancedhookingmaycausefallingoandyou

maybeinjured.

►Fig.11: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

eithersideandthensecureitwithascrew.Toremove,

loosen the screw and then take it out.

Using hole

WARNING: Never use the hanging hole for

unintended purpose, for instance, tethering the

tool at high location.Bearingstressinaheavily

loadedholemaycausedamagestothehole,result-

ingininjuriestoyouorpeoplearoundorbelowyou.

►Fig.12: 1. Hanging hole

Use the hanging hole at the bottom rear of the tool to

hang the tool on a wall using a hanging cord or similar

strings.

Installing driver bit holder

Optional accessory

►Fig.13: 1. Driver bit holder 2. Driver bit

Fit the driver bit holder into the protrusion at the tool foot

on either right or left side and secure it with a screw.

When not using the driver bit, keep it in the driver bit

holders. Driver bits 45 mm-long can be kept there.

11 ENGLISH

OPERATION

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

►Fig.14

NOTICE:Donotcovervents,oritmaycauseover-

heating and damage to the tool.

►Fig.15: 1. Vent

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

First,turntheadjustingringsothatthearrowonthetool

bodypointstotheproperfasteningtorquelevel(1-21).

Place the point of the driver bit in the screw head and

applypressuretothetool.Startthetoolslowlyandthen

increasethespeedgradually.Releasetheswitchtrigger

as soon as the clutch cuts in.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

and prevents splitting of the workpiece.

Drilling operation

CAUTION: Pressing excessively on the tool

will not speed up the drilling. In fact, this excessive

pressurewillonlyservetodamagethetipofyourdrill

bit, decrease the tool performance and shorten the

service life of the tool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

First,turntheadjustingringsothatthearrowpointsto

the marking.Thenproceedasfollows.

Drilling in wood

When drilling in wood, the best results are obtained

withwooddrillsequippedwithaguidescrew.Theguide

screwmakesdrillingeasierbypullingthedrillbitinto

the workpiece.

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole, make an indentation with a center-punch and

hammer at the point to be drilled. Place the point of the

drill bit in the indentation and start drilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers,alwaysusingMakitareplacementparts.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

Ifyouneedanyassistanceformoredetailsregard-

ingtheseaccessories,askyourlocalMakitaService

Center.

• Drillbits

• Driverbits

• Driverbitholder

• Hook

• Sidegrip

• Rubberpadassembly

• Woolbonnet

• Foampolishingpad

• Makitagenuinebatteryandcharger

NOTE:Someitemsinthelistmaybeincludedinthe

toolpackageasstandardaccessories.Theymay

dierfromcountrytocountry.

中文简体

中文简体 (原本)

规格

型号： DDF489

钻孔能力钢材 13 mm

木材螺旋钻头：38 mm

自进给钻头：51 mm

孔锯：51 mm

紧固能力木螺丝 10 mm × 90 mm

机器螺丝 M6

空载速度（RPM）高（2）0-1,800r/min

低（1）0-550r/min

总长度 174 mm

额定电压 D.C. 18 V

净重 1.8 - 2.5 kg

• 生产者保留变更规格不另行通知之权利。

• 规格可能因销往国家之不同而异。

• 重量因附件（包括电池组）而异。根据EPTA-Procedure01/2014，最重与最轻的组合见

表格。

适用电池组和充电器

电池组 BL1815N/BL1820B/BL1830B/

BL1840B/BL1850B/BL1860B

充电器 DC18RC/DC18RD/DC18RE/DC18SD/

DC18SE/DC18SF/DC18SH/DC18WC

• 部分以上所列电池组和充电器是否适用视用户所在地区而异。

警告：请仅使用以上所列电池组和充电器。使用其他类型的电池组或充电器可能会导致

人身伤害和／或失火。

中文简体

符号

以下显示本设备可能会使用的符号。在使用

工具之前，请务必理解其含义。

阅读使用说明书。

Ni-MH

Li-ion 仅限于欧盟国家

由于本设备中包含有害成分，

因此废弃的电气和电子设备、

蓄电池和普通电池可能会对环

境和人体健康产生负面影响。

请勿将电气和电子工具或电池

与家庭普通废弃物放在一起处

置！

根据欧洲关于废弃电气电子设

备、蓄电池和普通电池、废弃

的蓄电池和普通电池的指令及

其国家层面的修订法案，废弃

的电气设备、普通电池和蓄电

池应当单独存放并递送至城市

垃圾收集点，根据环保法规进

行处置。

此规定由标有叉形标志的带轮

垃圾桶符号表示。

用途

本工具用于在木材、金属和塑料中钻孔和拧

紧螺丝。

安全警告

电动工具通用安全警告

警告

阅读随电动工具提供的所有安全警

告、说明、图示和规定。不遵照以下所列说

明会导致电击、着火和／或严重伤害。

保存所有警告和说明书以备查

阅。

警告中的术语“电动工具”是指市电驱动（有

线）电动工具或电池驱动（无线）电动工具。

工作场地的安全

1. 保持工作场地清洁和明亮。杂乱和黑暗

的场地会引发事故。

2. 不要在易爆环境，如有易燃液体、气体

或粉尘的环境下操作电动工具。电动工

具产生的火花会点燃粉尘或气体。

3. 操作电动工具时，远离儿童和旁观者。

注意力不集中会使你失去对工具的控制。

电气安全

1. 电动工具插头必须与插座相配。绝不能

以任何方式改装插头。需接地的电动工

具不能使用任何转换插头。未经改装的

插头和相配的插座将降低电击风险。

2. 避免人体接触接地表面，如管道、散热

片和冰箱。如果你身体接触接地表面会

增加电击风险。

3. 不得将电动工具暴露在雨中或潮湿环境

中。水进入电动工具将增加电击风险。

4. 不得滥用软线。绝不能用软线搬运、拉

动电动工具或拔出其插头。使软线远离

热源、油、锐边或运动部件。受损或缠

绕的软线会增加电击风险。

5. 当在户外使用电动工具时，使用适合户

外使用的延长线。适合户外使用的电线

将降低电击风险。

6. 如果无法避免在潮湿环境中操作电动工

具，应使用带有剩余电流装置（RCD）

保护的电源。RCD的使用可降低电击风

险。

7. 电动工具会产生对用户无害的电磁场

（EMF）。但是，起搏器和其他类似医

疗设备的用户应在操作本电动工具前咨

询其设备的制造商和／或医生寻求建议。

人身安全

1. 保持警觉，当操作电动工具时关注所从

事的操作并保持清醒。当你感到疲倦，

或在有药物、酒精或治疗反应时，不要

操作电动工具。在操作电动工具时瞬间

的疏忽会导致严重人身伤害。

2. 使用个人防护装置。始终佩戴护目镜。

防护装置，诸如适当条件下使用防尘面

具、防滑安全鞋、安全帽、听力防护等

装置能减少人身伤害。

3. 防止意外起动。在连接电源和 /或电池包、

拿起或搬运工具前确保开关处于关断位

置。手指放在开关上搬运工具或开关处

于接通时通电会导致危险。

4. 在电动工具接通之前，拿掉所有调节钥

匙或扳手。遗留在电动工具旋转零件上

的扳手或钥匙会导致人身伤害。

5. 手不要过分伸展。时刻注意立足点和身

体平衡。这样能在意外情况下能更好地

控制住电动工具。

6. 着装适当。不要穿宽松衣服或佩戴饰品。

让你的头发和衣服远离运动部件。宽松

衣服、佩饰或长发可能会卷入运动部件。

中文简体

7. 如果提供了与排屑、集尘设备连接用的

装置，要确保其连接完好且使用得当。

使用集尘装置可降低尘屑引起的危险。

8. 不要因为频繁使用工具而产生的熟悉感

而掉以轻心，忽视工具的安全准则。某

个粗心的动作可能在瞬间导致严重的伤

害。

9. 使用电动工具时请始终佩带护目镜以免伤

害眼睛。护目镜须符合美国ANSI Z87.1、

欧洲EN 166或者澳大利亚／新西兰的

AS/NZS 1336的规定。在澳大利亚／

新西兰，法律要求佩带面罩保护脸部。

雇主有责任监督工具操作者和其他近工

作区域人员佩带合适的安全防护设备。

电动工具使用和注意事项

1. 不要勉强使用电动工具，根据用途使用

合适的电动工具。选用合适的按照额定

值设计的电动工具会使你工作更有效、

更安全。

2. 如果开关不能接通或关断电源，则不能

使用该电动工具。不能通过开关来控制

的电动工具是危险的且必须进行修理。

3. 在进行任何调节、更换附件或贮存电动

工具之前，必须从电源上拔掉插头和/或

卸下电池包（如可拆卸）。这种防护性

的安全措施降低了电动工具意外起动的

风险。

4. 将闲置不用的电动工具贮存在儿童所及

范围之外，并且不允许不熟悉电动工具

和不了解这些说明的人操作电动工具。

电动工具在未经培训的使用者手中是危

险的。

5. 维护电动工具及其附件。检查运动部件

是否调整到位或卡住，检查零件破损情

况和影响电动工具运行的其他状况。如

有损坏，应在使用前修理好电动工具。

许多事故是由维护不良的电动工具引发

的。

6. 保持切削刀具锋利和清洁。维护良好地

有锋利切削刃的刀具不易卡住而且容易

控制。

7. 按照使用说明书，并考虑作业条件和要

进行的作业来选择电动工具、附件和工

具的刀头等。将电动工具用于那些与其

用途不符的操作可能会导致危险情况。

8. 保持手柄和握持表面干燥、清洁，不得

沾有油脂。在意外的情况下，湿滑的手

柄不能保证握持的安全和对工具的控制。

9. 使用本工具时，请勿佩戴可能会缠结的

布质工作手套。布质工作手套卷入移动

部件可能会造成人身伤害。

电池式工具使用和注意事项

1. 仅使用生产者规定的充电器充电。将适

用于某种电池包的充电器用到其他电池

包时可能会发生着火危险。

2. 仅使用配有专用电池包的电动工具。使

用其他电池包可能会产生伤害和着火危

险。

3. 当电池包不用时，将它远离其他金属物

体，例如回形针、硬币、钥匙、钉子、

螺钉或其他小金属物体，以防电池包一

端与另一端连接。电池组端部短路可能

会引起燃烧或着火。

4. 在滥用条件下，液体可能会从电池组中

溅出；应避免接触。如果意外碰到液体，

用水冲洗。如果液体碰到了眼睛，还应

寻求医疗帮助。从电池中溅出的液体可

能会发生腐蚀或燃烧。

5. 不要使用损坏或改装过的电池包或工具。

损坏或改装过的电池组可能呈现无法预

测的结果，导致着火、爆炸或伤害。

6. 不要将电池包暴露于火或高温中。电池

包暴露于火或高于130 ℃的高温中可能

导致爆炸。

7. 遵循所有充电说明。不要在说明书中指

定的温度范围之外给电池包或电动工具

充电。不正确或在指定的温度范围外充

电可能会损坏电池和增加着火的风险。

维修

1. 让专业维修人员使用相同的备件维修电

动工具。这将保证所维修的电动工具的

安全。

2. 决不能维修损坏的电池包。电池包仅能

由生产者或其授权的维修服务商进行维

修。

3. 上润滑油及更换附件时请遵循本说明书

指示。

中文简体

充电式起子电钻使用安全警告

所有操作的安全注意事项

1. 当进行作业时切割附件或紧固装置可能

会接触到隐藏的电线，请握住电动工具

的绝缘抓握表面。切割附件或紧固装置

接触到“带电”的电线时，电动工具上

曝露的金属部分可能也会“带电”，并

使操作者触电。

2. 请务必确保立足稳固。在高处使用工具

时确保下方无人。

3. 请牢握本工具。

4. 手应远离旋转的部件。

5. 运行中的工具不可离手放置。只可在手

握工具的情况下操作工具。

6. 操作之后，请勿立即触摸钻头、工件或

碎屑，此时其温度可能会非常高，从而

导致皮肤烫伤。

7. 某些材料含有有毒化学物质。小心不要

吸入粉尘，并避免皮肤接触。遵循材料

供应商的安全提示。

8. 如果打开卡爪依然无法拧松钻头，请使

用虎钳将其拉出。在这种情况下，徒手

拉出钻头会因尖锐的边缘受伤。

9. 请确保不存在电缆、水管、煤气管道等，

如果其因使用本工具而受损，可能会引

起危险。

使用长钻头时的安全注意事项

1. 操作时的速度切勿高于钻头的额定速度。

在高速状态下，如果让钻头不接触工件

空转，则钻头可能会弯曲，造成人身伤

害。

2. 务必以低速开始钻孔，并将钻头的端部

与工件接触。在高速状态下，如果让钻

头不接触工件空转，则钻头可能会弯曲，

造成人身伤害。

3. 只在与钻头对齐的位置施加压力，切勿

过度施压。否则钻头可能弯曲导致破损

或失控，造成人身伤害。

请保留此说明书。

警告：请勿为图方便或因对产品足够熟

悉（由于重复使用而获得的经验）而不严格

遵循相关产品安全规则。使用不当或不遵循

使用说明书中的安全规则会导致严重的人身

伤害。

电池组的重要安全注意事项

1. 在使用电池组之前，请仔细通读所有的

说明以及（1）电池充电器，（2）电

池，以及（3）使用电池的产品上的警

告标记。

2. 切勿拆卸或改装电池组。否则可能引起

火灾、过热或爆炸。

3. 如果机器运行时间变得过短，请立即停

止使用。否则可能会导致过热、起火甚

至爆炸。

4. 如果电解液进入您的眼睛，请用清水将

其冲洗干净并立即就医。否则可能会导

致视力受损。

5. 请勿使电池组短路：

(1) 请勿使任何导电材料碰触到端子。

(2) 避免将电池组与其他金属物品如钉

子、硬币等放置在同一容器内。

(3) 请勿将电池组置于水中或使其淋雨。

电池短路将产生大的电流，导致过热，

并可能导致起火甚至击穿。

6. 请勿在温度可能达到或超过50°C（122°F）

的场所存放以及使用工具和电池组。

7. 即使电池组已经严重损坏或完全磨损，

也请勿焚烧电池组。电池组会在火中爆

炸。

8. 请勿对电池组射钉，或者切削、挤压、

抛掷、掉落电池组，又或者用硬物撞击

电池组。否则可能引起火灾、过热或爆

炸。

9. 请勿使用损坏的电池。

10. 本工具附带的锂离子电池需符合危险品

法规要求。

第三方或转运代理等进行商业运输时，

应遵循包装和标识方面的特殊要求。

有关运输项目的准备作业，咨询危险品

方面的专业人士。同时，请遵守可能更

为详尽的国家法规。

请使用胶带保护且勿遮掩表面的联络信

息，并牢固封装电池，使电池在包装内

不可动。

11. 丢弃电池组时，需将其从工具上卸下并

在安全地带进行处理。关于如何处理废

弃的电池，请遵循当地法规。

12. 仅将电池用于Makita（牧田）指定的产

品。将电池安装至不兼容的产品会导致

起火、过热、爆炸或电解液泄漏。

13. 如长时间未使用工具，必须将电池从工

具内取出。

中文简体

14. 使用工具期间以及使用工具之后，电池

组温度可能较高易引起灼伤或低温烫伤。

处理高温电池组时请小心操作。

15. 在使用工具后请勿立即触碰工具的端子，

否则可能引起灼伤。

16. 避免锯屑、灰尘或泥土卡入电池组的端

子、孔口和凹槽内。否则可能会导致过

热、着火、爆炸和工具/电池组故障，导

致烫伤或人身伤害。

17. 除非工具支持在高压电源线路附近使用，

否则请勿在高压电源线路附近使用电池

组。否则可能导致工具或电池组故障或

失常。

18. 确保电池远离儿童。

请保留此说明书。

小心：请仅使用Makita（牧田）原装电

池。使用非Makita（牧田）原装电池或经过

改装的电池可能会导致电池爆炸，从而造成

火灾、人身伤害或物品受损。同时也会导致

牧田工具和充电器的牧田保修服务失效。

保持电池最大使用寿命的提示

1. 在电池组电量完全耗尽前及时充电。发

现工具电量低时，请停止工具操作，并

给电池组充电。

2. 请勿对已充满电的电池组重新充电。过

度充电将缩短电池的使用寿命。

3. 请在10 °C - 40 °C（50 °F - 104 °F）的

室温条件下给电池组充电。请在灼热的

电池组冷却后再充电。

4. 不使用电池组时，请将其从工具或充电

器上拆除。

5. 如果电池组长时间（超过六个月）未使

用，请给其充电。

功能描述

小心：调节或检查工具功能之前，请务

必关闭工具的电源并取出电池组。

安装或拆卸电池组

小心：安装或拆卸电池组之前，请务必

关闭工具电源。

小心：安装或拆卸电池组时请握紧工具

和电池组。否则它们可能从您的手中滑落，导

致工具和电池组受损，甚至造成人身伤害。

► 图片1: 1. 红色指示器 2. 按钮 3. 电池组

拆卸电池组时，按下电池组前侧的按钮，同

时将电池组从工具中抽出。

安装电池组时，要将电池组上的舌簧与外罩

上的凹槽对齐，然后推滑到位。将其完全插

入到位，直到锁定并发出咔哒声为止。若能

看到图示中的红色指示器，则说明未完全锁

紧。

小心：务必完全装入电池组，直至看不

见红色指示器为止。否则，它可能会从工具

中意外脱落，从而造成自身或他人受伤。

小心：请勿强行安装电池组。如果电池

组难以插入，可能是插入方法不当。

显示电池的剩余电量

仅限带指示灯的电池组

► 图片2: 1. 指示灯 2. CHECK（查看）按钮

按电池组上的CHECK（查看）按钮可显示电

池剩余电量。指示灯将亮起数秒。

指示灯剩余电量

点亮熄灭闪烁

75%至

100%

50%至

75%

25%至

50%

0%至

25%

给电池

充电。

电池可

能出现

故障。

中文简体

注：在不同的使用条件及环境温度下，指示

灯所示电量可能与实际情况略有不同。

注：当电池保护系统启动时，第一个（最左

侧）指示灯将闪烁。

工具／电池保护系统

本工具配备有工具／电池保护系统。该系统

可自动切断电源以延长工具和电池寿命。作

业时，如果工具或电池处于以下情况，工具

将会自动停止运转。

过载保护

以导致异常高电流的方式操作工具／电池时，

此保护功能将启动。在这种情况下，请关闭

工具并停止导致工具过载的应用程序。然后

开启工具以重新启动。

过热保护

当工具或电池过热时，将启动此保护功能。

在这种情况下，请待工具和电池冷却后再开

启工具。

过放电保护

当剩余电池电量变低时，将启动此保护功能。

此时，请取出工具中的电池并予以充电。

其他原因防护

保护系统还适用于其他可能导致工具受损的

情况，从而使工具自动停止运转。工具暂时

或中途停止工作时，执行以下所有步骤以排

除异常原因。

1. 关闭工具，然后再次重新启动。

2. 给电池充电或更换为充电电池。

3. 请等待工具和电池冷却。

如果保护系统恢复后仍无改善，请联络当地

的Makita（牧田）维修服务中心。

开关操作

小心：在将电池组插入工具之前，请务

必检查开关扳机是否能扣动自如，松开时能

否退回至“OFF”（关闭）位置。

► 图片3: 1. 开关扳机

启动工具时，只要扣动开关扳机即可。随着

在开关扳机上施加压力的增大，工具速度会

提高。松开开关扳机工具即停止。

注：如果持续扣动开关扳机约6分钟，机器

将自动停止。

电动制动器

本工具配备有电动制动器。如果在松开开关

扳机后，工具始终无法立即停机，则须交由

Makita（牧田）维修中心维修。

点亮前灯

小心：请勿直视灯光或光源。

► 图片4: 1. 照明灯

扣动开关扳机点亮照明灯。在扣动开关扳机

期间此灯保持常亮。松开开关扳机约 10秒后，

灯将熄灭。

注：工具过热时，工具将自动停止运转且指

示灯开始闪烁。在这种情况下，请松开开关

扳机。指示灯将在一分钟内熄灭。

注：请使用干布擦拭灯头灰。注意不要刮

花灯头，否则会降低亮度。

反转切换柄操作

小心：操作前请务必检查旋转方向。

小心：仅在工具完全停止后使用反转切

换柄。若在工具停止前改变旋转方向，可能会

损坏工具。

小心：未操作工具时，请务必将反转切

换柄放在空档位置。

► 图片5: 1. 反转切换柄

本工具设有反转切换柄，可改变旋转方向。

从A侧按下反转切换柄可进行顺时针旋转；

从B侧按下可进行逆时针旋转。

反转切换柄处于空档位置时，开关扳机无法

扣动。

变速

小心：请务必将变速杆完全置于正确位

置。在变速杆处于“1”侧与“2”侧之间的

半位时操作工具，会使工具受损。

小心：请勿在机器运转时使用变速杆。

否则可能会损坏工具。

► 图片6: 1. 变速杆

中文简体

显示的

数字

速度转矩适用操作

1低高高负荷

操作

2高低低负荷

操作

要改变速度，请先关闭工具。需要高速时推

动变速杆以显示“2”，需要低速时推动变速

杆以显示“1”。确保使用之前将变速杆置于

正确位置。

如果在显示为“2”的操作中工具速度极速降

低，请推变速杆以显示“1”，然后重新开始

操作。

调节环

您可以利用调节环选择动作模式以及调节紧

固转矩。

选择动作模式

► 图片7: 1. 调节环 2. 标记 3. 箭头

本工具设有两种动作模式。

钻孔模式（仅旋转）

1 - 21 螺丝起子模式（离合

旋转）

选择适合您作业的模式。旋转调节环并将所

选标记与工具机身上的箭头对齐。

注意：一定要将调节环正确设置到所需的

模式标记处。如果在调节环位于模式标记之

间的中间位置时操作工具，则工具可能会受

损。

注意：请勿在工具转动时更改动作模式。

注意：若调节环难以滑动，开启工具并运

转片刻，然后停止工具，再将调节环滑动至

所需位置。

调节紧固转矩

► 图片8: 1. 调节环 2. 标记（1 - 21刻度）

3. 箭头

可通过转动调节环在21个等级范围内调节紧固扭矩。对齐刻度和工具主体上的箭头。设至

1时紧固扭矩最小，设至21时紧固扭矩最大。

实际操作前，将试验螺丝拧入材料或与其相同的材料，以确定具体应用所需的转矩水平。

刻度 12345678910 11 12 13 14 15 16 17 18 19 20 21

机器螺丝 M4 M5 M6

木螺丝软木

（如松

木）

─ø3.5 x 22 ø4.1 x 38 ─

硬木

（如柳

安木）

─ø3.5 x 22 ø4.1 x 38 ─

注：当箭头位于刻度间的中间位置时，调节环不会锁定。

装配

小心：对工具进行任何装配操作前，

请务必关闭工具电源，并取出电池组。

起子头／钻头的安装或拆卸

选购附件

► 图片9: 1. 套筒 2. 关闭 3. 打开

逆时针转动套筒以打开卡盘爪。尽量将起子

头／钻头放入卡盘最里侧。顺时针转动套筒

以关闭卡盘。逆时针转动套筒即可卸下起子

头／钻头。

中文简体

安装侧把手（辅助手柄）

选购附件

► 图片10: 1. 侧把手 2. 凸起部分 3. 凹槽

4. 臂

在过重负载下进行操作时，使用侧把手可更

稳固地控制工具。

安装侧把手，使电钻臂上的凸起部分嵌入工

具套筒的凹槽中。顺时针旋转把手将其紧固。

把手可固定在需要的角度。

侧把手可安装在工具左侧或右侧，视具体操

作情况而定。

安装挂钩

警告：仅可将悬挂/承载部件用于原本目

的，例如在作业或工作间隙时，将工具挂在

挂带上。

警告：小心不要让挂钩过载，过大的压

力或不正常的过载可能导致工具受损乃至人

身伤害。

小心：安装挂钩时，务必使用螺丝将其

固定。否则挂钩可能会脱离工具，导致人身

伤害。

小心：在松开手之前，务必确保工具被

稳固挂住。不完全或不平稳的挂载操作可能

导致工具掉落，乃至人身伤害。

► 图片11: 1. 凹槽 2. 挂钩 3. 螺丝

挂钩便于临时悬挂工具。可安装在工具的任

一侧。要安装挂钩，请将其插入工具外壳上

任一侧的凹槽中，然后用螺丝加以紧固。要

拆卸挂钩，请将螺丝拧松，然后将其取出。

孔的使用

警告：切勿将悬挂孔用于非预期用途，

例如将工具系于高处。重载孔内承受应力会

导致其损坏，进而伤及您或者您周围或下方

的人员。

► 图片12: 1. 悬挂孔

使用工具后侧底部的悬挂孔并搭配挂绳或类

似绳索将工具挂在墙壁上。

安装起子头夹持器

选购附件

► 图片13: 1. 起子头夹持器 2. 起子头

将起子头夹持器嵌入工具底座左侧或右侧的

突起中，并用螺丝加以紧固。

不使用起子头时，将其存放在起子头夹持器

内。夹持器可存放45 mm长的起子头。

操作

小心：如果速度极速降低，请减小负荷

或停止工具以避免损坏工具。

一手握住机器把手，另一只手握住电池组底

部，紧握机器，防止其出现扭动现象。

► 图片14

注意：请勿遮盖通风口，否则可能导致工

具因过热而受损。

► 图片15: 1. 通风口

旋紧螺丝的操作

小心：将调节环调至适当的转矩等级操

作。

小心：务必要将起子头平直地插入螺丝

头端，否则会损坏螺丝和／或起子头。

首先，旋转调节环使工具机身上的箭头指向

适当的紧固转矩等级（1 - 21）。

将起子头的尖端放进螺丝头部并对工具施加

压力。要慢速启动工具，然后逐渐提高转速。

插入离合器的同时即可松开开关扳机。

注：钉入木螺丝时，应先钻直径为木螺丝

直径2/3的引导孔。以便于操作并防止工件开

裂。

中文简体

钻孔操作

小心：过分用力按压工具并不会提高钻

孔效率。事实上，过大的压力只会损坏钻头

尖，降低工具性能，缩短工具使用寿命。

小心：钻头即将钻穿工件时需握紧工

具，注意力集中。钻穿时工具／钻头会受到

极大的突然扭力。

小心：取出卡住的钻头时，只需将反转

开关设为反向旋转便可退出工具。但如果不

紧紧握住工具，工具可能突然退出。

小心：请务必用虎钳或类似夹紧装置固

定工件。

小心：如果工具连续工作到电池组电量

耗尽，则应暂停使用工具15分钟，再用充电

后的电池继续操作。

首先，转动调节环使箭头指向标记。然

后进行如下操作。

在木材上钻孔

在木材上钻孔时，使用带有前导螺丝的木材

用钻头将获得最佳效果。这种前导螺丝可令

钻孔操作更加轻松。

在金属上钻孔

开始钻孔时，为了防止钻头打滑，可用一尖冲头

和锤子在金属板上想要钻孔的地方打一痕记。

将钻头尖端放入凹痕，然后开始钻孔。

在金属上钻孔时请使用切割油。但在铁和铜

材料上钻孔时应干钻。

保养

小心：检查或保养工具之前，请务必关

闭工具电源并取出电池组。

注意：切勿使用汽油、苯、稀释剂、酒精

或类似物品清洁工具。否则可能会导致工具

变色、变形或出现裂缝。

为了保证产品的安全与可靠性，维修、任何

其他的维修保养或调节需由Makita（牧田）

授权的或工厂维修服务中心完成。务必使用

Makita（牧田）的替换部件。

选购附件

小心：这些附件或装置专用于本说明书

所列的Makita（牧田）工具。如使用其他厂

牌附件或装置，可能导致人身伤害。仅可将

附件或装置用于规定目的。

如您需要了解更多关于这些选购附件的信息，

请咨询当地的Makita（牧田）维修服务中心。

• 钻头

• 起子头

• 起子头夹持器

• 挂钩

• 侧把手

• 橡胶垫组件

• 羊毛抛光球

• 泡沫抛光垫

• Makita（牧田）原装电池和充电器

注：本列表中的一些部件可能作为标准配件

包含于工具包装内。它们可能因销往国家之

不同而异。

ページを読み込んでいます...

Makita DDF489 ユーザーマニュアル

関連論文