Makita UR012G ユーザーマニュアル

UR012G

EN Cordless Grass Trimmer INSTRUCTION MANUAL 11

ZHCN 充电式割草机使用说明书 26

ID Alat Potong Rumput Tanpa

Kabel PETUNJUK PENGGUNAAN 43

MS Pemangkas Rumput Tanpa

Kord MANUAL ARAHAN 60

VI Máy Tỉa Hàng Rào Cầm Tay

Hoạt Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 77

TH   93

Fig.1

12 2

Fig.2

12 1

2

3

4

5

8

9

10

11

Fig.3

6

7

8

9

10

11

12 13 14

15

16

1 2

3

4 5

Fig.4

2

1

2

3

Fig.5

1

2

Fig.6

2

1

Fig.7

1

2

Fig.8

2

1

Fig.9

2

1

Fig.10

3

2

1

Fig.11

3

1

3

2

Fig.12

1

3

2

4

5

6

Fig.13

1

Fig.14

1

2

Fig.15

1

2

Fig.16

1

2 2

3

4

5

6

Fig.17

1

2

Fig.18

1

2

3

4

Fig.19

4

1

2

Fig.20

1

2

3

4

5

6

Fig.21

1

Fig.22

Fig.23

Fig.24

1

2

4

3

Fig.25

1

2

3

4

5

Fig.26

1

2

3

4

5

Fig.27

5

Fig.28

2

1

Fig.29

Fig.30

1

Fig.31

2

1

Fig.32

12

3

750 mm

100-300 mm

Fig.33

Fig.34

1

Fig.35

6

1

Fig.36

Fig.37

Fig.38

Fig.39

7

1

2

3

5

4

6

7

8

3 m

80 mm

100 mm

Fig.40

8

9

1

2

4

3

5

6

3 m

100 mm

Fig.41

10

Fig.42

1

2

Fig.43

90°

1

2

Fig.44

11 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: UR012G

Handle type Bike handle

No load speed

(at each rotation speed level)

Cutter blade / Plastic blade 3: 0 - 6,800 min-1

2: 0 - 5,000 min-1

1: 0 - 3,500 min-1

Nylon cutting head 3: 0 - 5,000 min-1

2: 0 - 4,200 min-1

1: 0 - 3,500 min-1

Overall length

(without cutting tool)

1,790 mm

Nylon cord diameter 2.4 - 3.0 mm

Applicable cutting tool and

cutting diameter

2-tooth blade

(P/N 195624-6)

305 mm

3-tooth blade

(P/N 195300-2)

305 mm

4-tooth blade

(P/N 196895-8)

255 mm

8-tooth blade

(P/N B-14146)

255 mm

Chisel blade

(P/N 199872-9)

225 mm

Shredder blade

(P/N 199874-5)

270 mm

Nylon cutting head

(P/N 199884-2)

480 mm

Plastic blade

(P/N 199868-0)

305 mm

Rated voltage D.C. 72 V - 80 V max

Net weight 8.0 - 9.3 kg

Protection degree IPX4

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025 / BL4040 / BL4050F*

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

andchargersmaycauseinjuryand/orre.

12 ENGLISH

Symbols

Thefollowingsshowthesymbolswhichmaybeused

fortheequipment.Besurethatyouunderstandtheir

meaningbeforeuse.

Takeparticularcareandattention.

Read instruction manual.

15m(50FT)Keep distance at least 15 m.

Caution; kickback

Wear a helmet, goggles and ear protection.

Wear protective gloves.

Wear sturdy boots with nonslip soles.

Steeltoedsafetybootsarerecommended.

Danger;beawareofthrownobjects.

Warning;Disconnectbatterybefore

maintenance.

Warning:Hotsurface.Riskofburns.Donot

touch metal part until cooled.

Wear eye and ear protection.

Ni-MH

Li-ion

OnlyforEUcountries

Duetothepresenceofhazardouscom-

ponentsintheequipment,wasteelectrical

andelectronicequipment,accumulators

and batteries may have a negative impact

on the environment and human health.

Donotdisposeofelectricalandelectronic

appliances or batteries with household

waste!

In accordance with the European Directive

onwasteelectricalandelectronicequip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

wasteelectricalequipment,batteriesand

accumulators should be stored separately

and delivered to a separate collection point

formunicipalwaste,operatinginaccor-

dance with the regulations on environmen-

tal protection.

Thisisindicatedbythesymbolofthe

crossed-out wheeled bin placed on the

equipment.

Guaranteed sound power level according

to EU Outdoor Noise Directive.

Sound power level according to Australia

NSW Noise Control Regulation.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool.Failuretofollowallinstructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm“powertool”inthewarningsreferstoyour

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

whichmayignitethedustorfumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduceriskofelectricshock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tricshockifyourbodyisearthedorgrounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

theriskofelectricshock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increasetheriskofelectricshock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use.Useof

acordsuitableforoutdoorusereducestheriskof

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.UseofanRCDreduces

theriskofelectricshock.

7. Power tools can produce electromagnetic

elds (EMF) that are not harmful to the user.

However,usersofpacemakersandothersimilar

medicaldevicesshouldcontactthemakeroftheir

deviceand/ordoctorforadvicebeforeoperating

this power tool.

13 ENGLISH

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication.Amomentofinattentionwhileoperating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection.Protectiveequipmentsuch

asadustmask,non-skidsafetyshoes,hardhator

hearingprotectionusedforappropriateconditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attachedtoarotatingpartofthepowertoolmay

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

ofthepowertoolinunexpectedsituations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.Looseclothes,jewelleryor

long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.Useof

dustcollectioncanreducedust-relatedhazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

cancausesevereinjurywithinafractionofa

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rateforwhichitwasdesigned.

2. Do not use the power tool if the switch does

not turn it on and o. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools.Suchpreventivesafetymeasuresreduce

theriskofstartingthepowertoolaccidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

handsofuntrainedusers.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed.Useofthepowertool

foroperationsdierentfromthoseintendedcould

resultinahazardoussituation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handlesandgraspingsurfacesdonotallowfor

safehandlingandcontrolofthetoolinunexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled.Theentangle-

mentofclothworkglovesinthemovingpartsmay

resultinpersonalinjury.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer.Achargerthatissuitablefor

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs.Useofanyotherbattery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

14 ENGLISH

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

may exhibit unpredictable behaviour resulting in

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Never service damaged battery packs. Service

ofbatterypacksshouldonlybeperformedbythe

manufacturerorauthorizedserviceproviders.

3. Follow instruction for lubricating and chang-

ing accessories.

Important safety instructions for the

tool

WARNING: Read all safety warnings and

all instructions.Failuretofollowthewarningsand

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Intended use

1. This tool is only intended for cutting grass,

weeds, bushes and undergrowth. It should not

be used for any other purpose such as edging

or hedge cutting as this may cause injury.

General instructions

1. Never allow people unfamiliar with these

instructions, people (including children) with

reduced physical, sensory or mental capabil-

ities, or lack of experience and knowledge to

use the tool. Children should be supervised to

ensure that they do not play with the tool.

2. Before starting the tool, read this instruction

manual to become familiar with the handling of

the tool.

3. Do not lend the tool to a person with insu-

cient experience or knowledge regarding han-

dling of brushcutters and string trimmers.

4. When lending the tool, always attach this

instruction manual.

5. Handle the tool with the utmost care and

attention.

6. Never use the tool after consuming alcohol or

drugs, or if feeling tired or ill.

7. Never attempt to modify the tool.

8. Follow the regulations about handling of

brushcutters and string trimmers in your

country.

Personal protective equipment

►Fig.1

1. Wear safety helmet, protective goggles and

protective gloves to protect yourself from

ying debris or falling objects.

2. Wear ear protection such as ear mus to pre-

vent hearing loss.

3. Wear proper clothing and shoes for safe

operation, such as a work overall and sturdy,

non-slip shoes. Do not wear loose clothing or

jewelry.Looseclothes,jewelryorlonghaircanbe

caught in moving parts.

4. When touching the cutting blade, wear protec-

tive gloves. Cutting blades can cut bare hands

severely.

Work area safety

1. Operate the tool under good visibility and day-

light conditions only. Do not operate the tool in

darkness or fog.

2. Do not operate the tool in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust.Thetoolcreatessparks

whichmayignitethedustorfumes.

3. During operation, never stand on an unstable

or slippery surface or a steep slope. During

the cold season, beware of ice and snow and

always ensure secure footing.

4. During operation, keep bystanders or animals

at least 15 m away from the tool. Stop the tool

as soon as someone approaches.

5. Never operate the tool while people, especially

children, or pets are nearby.

6. Before operation, examine the work area for

stones or other solid objects.Theycanbe

thrown or cause dangerous kickback and result in

seriousinjuryand/orpropertydamage.

7. WARNING: Use of this product can create

dust containing chemicals which may cause

respiratory or other illnesses. Some examples

of these chemicals are compounds found in

pesticides, insecticides, fertilizers and herbi-

cides. Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to lter out microscopic particles.

Electrical and battery safety

1. Do not expose the tool to rain or wet condi-

tions. Water entering the tool will increase the risk

ofelectricshock.

2. Do not use the tool if the switch does not

turn it on and o. Any tool that cannot be con-

trolled with the switch is dangerous and must be

repaired.

15 ENGLISH

3. Prevent unintentional starting. Ensure the

switch is in the o-position before installing a

battery pack, picking up or carrying the tool.

Carryingthetoolwithyourngerontheswitchor

energising the tool that have the switch on invites

accidents.

4. Do not dispose of the battery(ies) in a re.

Thecellmayexplode.Checkwithlocalcodesfor

possible special disposal instructions.

5. Do not open or mutilate the battery(ies).

Released electrolyte is corrosive and may cause

damagetotheeyesorskin.Itmaybetoxicif

swallowed.

6. Do not charge battery in rain, or in wet

locations.

7. Avoid dangerous environment. Don't use the

tool in dump or wet locations or expose it to

rain. Water entering the tool will increase the risk

ofelectricshock.

8. Do not charge the battery outdoors.

9. Do not handle charger, including charger plug,

and charger terminals with wet hands.

10. Do not replace the battery with wet hands.

11. Do not replace the battery in the rain.

12. Do not wet the terminal of battery with liquid

such as water, or submerge the battery. Do not

leave the battery in the rain, nor charge, use,

or store the battery in a damp or wet place.If

theterminalgetswetorliquidentersinsideofbat-

tery, the battery may be short circuited and there is

ariskofoverheat,re,orexplosion.

13. After removing the battery from the tool or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

14. If the battery cartridge gets wet, drain the

water inside and then wipe it with a dry cloth.

Dry the battery cartridge completely in a dry

place before use.

Putting into operation

1. Before assembling or adjusting the tool,

remove the battery cartridge.

2. Before handling the cutter blade, wear protec-

tive gloves.

3. Before installing the battery cartridge, inspect

the tool for damages, loose screws/nuts or

improper assembly. Sharpen blunt cutter

blade. If the cutter blade is bent or dam-

aged, replace it. Check all control levers and

switches for easy action. Clean and dry the

handles.

4. Never attempt to switch on the tool if it is dam-

aged or not fully assembled. Otherwise serious

injurymayresult.

5. Adjust the shoulder harness and hand grip to

suit the operator's body size.

6. When inserting a battery cartridge, keep the

cutting attachment clear of your body and

other object, including the ground. It may rotate

whenstartingandmaycauseinjuryordamageto

the tool and/or property.

7. Remove any adjusting key, wrench or blade

cover before turning the tool on. An accessory

leftattachedtoarotatingpartofthetoolmay

resultinpersonalinjury.

8. The cutting tool has to be equipped with the

guard. Never run the tool with damaged guards

or without guards in place!

9. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

Operation

1. In the event of an emergency, switch o the

tool immediately.

2. If you feel any unusual condition (e.g. noise,

vibration) during operation, switch o the

tool and remove the battery cartridge. Do not

use the tool until the cause is recognized and

solved.

3. The cutting attachment continues to rotate for

a short period after turning the tool o. Don't

rush to contact the cutting attachment.

4. During operation, use the shoulder harness.

Keep the tool on your right side rmly.

5. Do not overreach. Keep proper footing and

balance at all times. Watch for hidden obsta-

cles such as tree stumps, roots and ditches to

avoid stumbling.

6. Always be sure of your footing on slopes.

7. Walk, never run.

8. Never work on a ladder or tree to avoid loss of

control.

9. If the tool gets heavy impact or fall, check the

condition before continuing work. Check the

controls and safety devices for malfunction. If

there is any damage or doubt, ask our autho-

rized service center for the inspection and

repair.

10. Do not touch the gear case during and imme-

diately after the operation.Thegearcase

becomes hot during operation and can cause burn

injury.

11. Take a rest to prevent loss of control caused

by fatigue. We recommend taking a 10 to 20-min-

ute rest every hour.

12. When you leave the tool, even if it is a short

time, always remove the battery cartridge.The

unattended tool with the battery cartridge installed

maybeusedbyunauthorizedpersonandcause

serious accident.

13. If grass or branches get caught between the

cutting attachment and guard, always turn

the tool o and remove the battery cartridge

before cleaning. Otherwise the cutting attach-

ment may rotate unintentionally and cause serious

injury.

14. Never touch moving hazardous parts before

the moving hazardous parts have come to

a complete stop and the battery cartridge is

removed.

15. If the cutting attachment hits stones or other

hard objects, immediately turn the tool o.

Then remove the battery cartridge and inspect

the cutting attachment.

16 ENGLISH

16. Check the cutting attachment frequently

during operation for cracks or damages.

Before the inspection, remove the battery

cartridge and wait until the cutting attachment

stops completely. Replace damaged cutting

attachment immediately, even if it has only

supercial cracks.

17. Never cut above waist height.

18. Before starting the cutting operation, wait until

the cutting attachment reaches a constant

speed after turning the tool on.

19. When using a cutting blade, swing the tool

evenly in half-circle from right to left, like

using a scythe.

20. Hold the tool by insulated gripping surfaces

only, because the cutter blade may contact

hidden wiring.Cutterbladescontactinga“live”

wiremaymakeexposedmetalpartsofthetool

“live”andcouldgivetheoperatoranelectric

shock.

21. Do not start the tool when the cutting tool is

tangled with cut grass.

22. Before starting the tool, be sure that the cut-

ting tool is not touching the ground and other

obstacles such as a tree.

23. During operation always hold the tool with

both hands. Never hold the tool with one hand

during use.

24. Do not use the tool when there is a risk of

lightning.

25. When you use the tool on muddy ground, wet

slope, or slippery place, pay attention to your

footing.

26. Avoid working in poor environment where

increased user fatigue is expected.

27. Do not use the tool in bad weather where visi-

bility is limited.Failuretodosomaycausefallor

incorrect operation due to low visibility.

28. Do not submerge the tool into a puddle.

29. Do not leave the tool unattended outdoors in

the rain.

30. When wet leaves or dirt adhere to the suc-

tion mouth (ventilation window) due to rain,

remove them.

31. Do not use the tool in the snow.

Cutting tools

1. Do not use a cutting tool which is not recom-

mended by Makita.

2. Use an applicable cutting attachment for the

job in hand.

— Nylon cutting heads (string trimmer heads)

andplasticbladesaresuitablefortrimming

lawn grass.

— Cuttingbladesaresuitableforcuttingweeds,

high grasses, bushes, shrubs, underwood,

thicket, and the like.

— Never use other blades including metal

multi-piecepivotingchainsandailblades.It

mayresultinseriousinjury.

3. Only use the cutting tool that are marked with

a speed equal or higher than the speed marked

on the tool.

4. Always keep your hands, face, and clothes

away from the cutting tool when it is rotating.

Failuretodosomaycausepersonalinjury.

5. Always use the cutting attachment guard prop-

erly suited for the cutting attachment used.

6. When using cutting blades, avoid kickback

and always prepare for an accidental kickback.

See the section for Kickback.

7. When not in use, attach the blade cover onto

the blade. Remove the cover before operation.

Kickback (Blade thrust)

1. Kickback (blade thrust) is a sudden reaction

to a caught or bound cutting blade. Once it

occurs, the tool is thrown sideway or toward

the operator at great force and it may cause

serious injury.

2. Kickback occurs particularly when applying

the blade segment between 12 and 2 o'clock

to solids, bushes and trees with 3 cm or larger

diameter.

►Fig.2

3. To avoid kickback:

1. Apply the segment between 8 and

11 o'clock.

2. Never apply the segment between 12 and

2 o'clock.

3. Never apply the segment between 11 and

12 o'clock and between 2 and 5 o'clock,

unless the operator is well trained and

experienced and does it at his/her own

risk.

4. Never use cutting blades close to solids,

such as fences, walls, tree trunks and

stones.

5. Never use cutting blades vertically, for

such operations as edging and trimming

hedges.

►Fig.3

Vibration

1. People with poor circulation who are exposed

to excessive vibration may experience injury

to blood vessels or the nervous system.

Vibrationmaycausethefollowingsymptoms

tooccurinthengers,handsorwrists:“Falling

asleep”(numbness),tingling,pain,stabbingsen-

sation,alterationofskincolororoftheskin.Ifany

ofthesesymptomsoccur,seeaphysician!

2. To reduce the risk of “white nger disease”,

keep your hands warm during operation and

well maintain the tool and accessories.

Transport

1. Before transporting the tool, turn it o and

remove the battery cartridge. Attach the cover

to the cutting blade.

2. When transporting the tool, carry it in a hori-

zontal position by holding the shaft.

3. When transporting the tool in a vehicle, prop-

erly secure it to avoid turnover. Otherwise

damage to the tool and other baggage may result.

17 ENGLISH

Maintenance

1. Have your tool serviced by our authorized

service center, always using only genuine

replacement parts. Incorrect repair and poor

maintenancecanshortenthelifeofthetooland

increasetheriskofaccidents.

2. Before doing any maintenance or repair work

or cleaning the tool, always turn it o and

remove the battery cartridge.

3. Always wear protective gloves when handling

the cutting blade.

4. Always clean dust and dirt o the tool. Never

use gasoline, benzine, thinner, alcohol or the

like for the purpose.Discoloration,deformation

orcracksoftheplasticcomponentsmayresult.

5. After each use, tighten all screws and nuts.

6. Do not attempt any maintenance or repair not

described in the instruction manual. Ask our

authorized service center for such work.

7. Always use our genuine spare parts and

accessories only. Using parts or accessories

supplied by a third party may result in the tool

breakdown, property damage and/or serious

injury.

8. Request our authorized service center to

inspect and maintain the tool at regular

interval.

9. Always keep the tool in good working condi-

tion.Poormaintenancecanresultininferiorper-

formanceandshortenthelifeofthetool.

10. Do not wash the tool with high pressure water.

11. When washing the tool, do not let water enter

the electrical mechanism such as battery,

motor, and terminals.

12. When storing the tool, avoid direct sunlight

and rain, and store it in a place where it does

not get hot or humid.

13. Perform inspection or maintenance in a place

where rain can be avoided.

14. After using the tool, remove the adhered dirt

and dry the tool completely before storing.

Depending on the season or the area, there is a

riskofmalfunctionduetofreezing.

Storage

1. Before storing the tool, perform full cleaning

and maintenance. Remove the battery car-

tridge. Attach the cover to the cutting blade.

2. Store the tool in a dry and high or locked loca-

tion out of reach of children.

3. Do not prop the tool against something, such

as a wall.Otherwiseitmayfallsuddenlyand

causeaninjury.

First aid

1. Always have a rst-aid kit close by.

Immediately replace any item taken from the

rst aid kit.

2. When asking for help, give the following

information:

— Placeoftheaccident

— What happened

— Numberofinjuredpersons

— Natureoftheinjury

— Your name

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

18 ENGLISH

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwardingagents,specialrequirementonpack-

aging and labeling must be observed.

Forpreparationoftheitembeingshipped,consult-

inganexpertforhazardousmaterialisrequired.

Please also observe possibly more detailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmayresultinpoorperformanceor

breakdownofthetoolorbatterycartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines.Itmayresultinamalfunction

orbreakdownofthetoolorbatterycartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Useofnon-genuineMakitabatteries,orbatteriesthat

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

alsovoidtheMakitawarrantyfortheMakitatooland

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

PARTS DESCRIPTION

►Fig.4

1Speed indicator 2ADTindicator

(ADT=AutomaticTorque

DriveTechnology)

3Caution lamp 4Main power button

5Reverse button 6Battery cartridge 7Hanger 8Lock-olever

9Switch trigger 10 Knob 11 Handle 12 Protector(forcutter

blade / nylon cutting

head / plastic blade)

13 Protector(forchisel

blade)

14 Protector(forshredder

blade)

15 Protectorextension(for

nylon cutting head /

plastic blade)

16 Shoulder harness

NOTE:Theprotectorsuppliedasthestandardaccessoryvariesdependingonthecountries.

19 ENGLISH

FUNCTIONAL

DESCRIPTION

WARNING: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Failuretoswitchoandremovethebatterycartridge

mayresultinseriouspersonalinjuryfromaccidental

start-up.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.5: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

withalittleclick.Ifyoucanseetheredindicatoras

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

not being inserted correctly.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsopowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placedunderoneofthefollowingconditions:

Caution lamp Status

Color On Blinking

Green Overload

Red (tool) / (battery) Overheat

Red

Overdischarge

Overload protection

Ifthetoolgetsintooneofthefollowingsituation,the

tool automatically stops and the caution lamp starts

blinking in green:

— Thetoolisoverloadedbyentangledweedsor

other debris.

— Thecutterbladeislockedorkickedback.

— Themainpowerbuttonisturnedonwhilethe

switch trigger is being pulled.

In this situation, release the trigger and pull it again to

resume.

CAUTION: If you need to remove the entan-

gled weeds on the tool or release the locked

cutter blade, be sure to turn the tool o before

you start.

Overheat protection for tool or

battery

Ifthetoolorbatterycartridgeisoverheated,thetool

stops automatically. When the tool is overheated, the

caution lamp lights up in red. When the battery cartridge

is overheated, the caution lamp blinks in red. Let the

tooland/orbatterycooldownbeforeturningthetoolon

again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically and the caution lamp starts blinking in red.

Ifthetooldoesnotoperateevenwhentheswitchesare

operated,removethebatterycartridgefromthetooland

charge it.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

lightupforafewseconds.

►Fig.6: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

20 ENGLISH

NOTE:Dependingontheconditionsofuseandthe

ambienttemperature,theindicationmaydierslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Main power switch

Tapthemainpowerbuttontoturnonthetool.

Toturnothetool,pressandholdthemainpower

buttonuntilthespeedindicatorgoeso.

►Fig.7: 1. Speed indicator 2. Main power button

NOTE:Thetoolwillautomaticallyturnedoifitisleft

withoutanyoperationsforacertainperiodoftime.

Switch action

WARNING: For your safety, this tool is

equipped with lock-o lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pressing the lock-o lever. Return the tool

to our authorized service center for proper repairs

BEFORE further usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-o lever.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the “OFF” position when released. Operating a tool

with a switch that does not actuate properly can lead

tolossofcontrolandseriouspersonalinjury.

CAUTION: Never put your nger on the main

power button and switch trigger when carrying

the tool.Thetoolmaystartunintentionallyandcause

injury.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-o lever. This can cause

switch breakage.

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-oleverisprovided.Tostartthetool,

depressthelock-oleverandpulltheswitchtrigger.

Thetoolspeedincreasesbyincreasingpressureonthe

switch trigger. Release the switch trigger to stop.

►Fig.8: 1.Lock-olever2. Switch trigger

Speed adjusting

Youcanadjustthetoolspeedbytappingthemain

power button. Each time you tap the main power button,

thelevelofspeedwillchange.Thetoolautomatically

adjuststherotationspeedaccordingtothecuttingtool

attached to the tool.

►Fig.9: 1. Speed indicator 2. Main power button

Speed

indicator

Mode Rotation speed

Cutter blade/

Plastic blade

Nylon cutting

head

High 0 -

6,800 min-1

0 -

5,000 min-1

Medium 0 -

5,000 min-1

0 -

4,200 min-1

Low 0 -

3,500 min-1

0 -

3,500 min-1

Automatic Torque Drive Technology

WhenyouturnontheAutomaticTorqueDrive

Technology(ADT),thetoolrunsatoptimumrotation

speedandtorquefortheconditionofgrassbeingcut.

Thetoolautomaticallydetectsthecuttingtoolattached

and choose a suitable rotation speed.

TostartADT,pressandholdthereversebuttonuntilthe

ADTindicatorturnson.

TostopADT,pressandholdthereversebuttonuntilthe

ADTindicatorturnso.

►Fig.10: 1.ADTindicator2. Reverse button

Indicator Mode Cutting tool Rotation

speed

ADT Cutter blade

Plastic blade

3,500 -

6,800 min-1

Nylon cutting

head

3,500 -

5,000 min-1

Reverse button for debris removal

WARNING: Switch o the tool and remove

the battery cartridge before you remove entan-

gled weeds or debris which the reverse rotation

function can not remove.Failuretoswitchoand

remove the battery cartridge may result in serious

personalinjuryfromaccidentalstart-up.

Thistoolhasareversebuttontochangethedirectionof

rotation.Itisonlyforremovingweedsanddebrisentan-

gled in the tool.

Toreversetherotation,tapthereversebuttonandpull

theswitchtriggerwhiledepressingthelock-olever

whenthecuttingtoolisstopped.Thespeedindicators

andADTindicatorstartblinking,andthecuttingtool

rotates in reverse direction when you pull the switch

trigger.

Toreturntoregularrotation,releasethetriggerandwait

until the cutting tool stops.

►Fig.11: 1. Speed indicator 2.ADTindicator

3. Reverse button

ページを読み込んでいます...

Makita UR012G ユーザーマニュアル

関連論文

その他の書類