CG36DC • CG36DC(L)
CG36DC
CG36DC(L)
en
zh
Handling instructions
en
zh
2
1
CG36DC
CG36DC(L)
A
A
H
FG
E
E
I
K
K
J
L
B
B
D
N
M
D
M
C
C
O
PT
QR
S
23
CG36DC
CG36DC(L)
3
45
3
5
12
4
2
1
78
6
67
1
9
12
11
11
15
10
14
16
13
89
18
21
20
19
17
16
20
10
22
23
25
24
4
10 11
28
26 27
24
28
26 27
24
11
2
23
34
4
12 13
30
33
31 10
32
29
7
30 32
14 15
32
34
33
33
76
31
5
16 17 18
35
36
37
35
39
38
41
42
40
25
43
36
44
45
19 20
45
45
46
35
47
36
52
51
50
48
49
38
39
25
40
21
CG36DC CG36DC(L)
a
b
53
54 56
56
55
55
53
POWER
ECO
AUTO
6
22
18
57
58
18
17
57
17
58
CG36DC
CG36DC(L)
23 24
7
25 26
54
60 59
1
27 28
1
ab
11
2
2
29 30
11
2
2
62
61
8
31
63 65
64
66
68
67
ba
32
69 43
100 mm
68
71
70
67
100 mm
d
c
b
a
9
33 34
67
36
68
43
72
73
74
65
75
35
110–140 mm
36
48 1.9–2.2 mm
10
English
Be careful of thrown objects.
Max
8,000 /min
Shows maximum shaft speed. Do not
use the cutting attachment whose max
rpm is below the shaft rpm.
Gloves should be worn when necessary,
e.g., when assembling cutting
equipment.
Use anti-slip and sturdy footwear.
Blade thrust may occur when the spinning
blade contacts a solid object in the critical
area. A dangerous reaction may occur
causing the entire unit and operator to
be thrust violently. This reaction is called
blade thrust. As a result, the operator may
lose control of the unit which may cause
serious or fatal injury. Blade thrust is more
likely to occur in areas where it is diffi cult
to see the material to be cut.
(CG36DC) Indicate handle location. Arrows which
show limits for handle positioning.
(CG36DC(L))
Direct current
V Rated voltage
n0No-load speed
Switching ON
Switching OFF
Eco mode
Auto mode
Power mode
Protection function activates
Battery
Lights ;
The battery remaining power is over 75%
Lights ;
The battery remaining power is 50%–75%.
Lights ;
The battery remaining power is 25%–50%.
Lights ;
The battery remaining power is less than 25%
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
CG36DC / CG36DC(L):
Cordless Grass Trimmer / Brush Cutter
To reduce the risk of injury, user must
read instruction manual.
Disconnect battery before maintenance
Always wear eye protection.
Always wear hearing protection.
Do not use a power tool in the rain and
moisture or leave it outdoors when it is
raining.
Beware of thrown objects
The distance between the machine and
bystanders shall be at least 15 m (50 ft)
Wear head protection
Wear hand protection
Wear slip-resistant footwear
Beware of blade thrust
It is important that you read, fully
understand and observe the following
safety precautions and warnings.
Careless or improper use of the unit may
cause serious or fatal injury.
Read, understand and follow all
warnings and instructions in this manual
and on the unit.
Prohibited action
Always wear eye, head and ear
protectors when using this unit.
Keep all children, bystanders and
helpers 15 m away from the unit. If
anyone approaches you, stop the unit
and cutting attachment immediately.
11
English
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to
fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please
contact your dealer.
WHAT IS WHAT? (Fig. 1)
A: Lever: Trigger for activating the unit.
B: Lock lever: Lever that prevents the accidental operation
of the trigger.
C: Motor: Battery-driven motor.
D: Guard: Protects operator from fl ying debris.
E: Battery (sold separately): Power source to drive the unit.
F: Power switch: Switch for switching the units power unit's
power ON or OFF.
G: Mode switch: Switch for adjusting the speed of the
motor.
H: Handle right: Handle with lever located on the right side
of the unit.
I: Handle left: Handle located on the left side of the unit.
J: Handle fi xture: Secures the handles to the unit.
K: Hanger: Used for attaching a shoulder belt to the unit.
L: Loop handle
M: Cutting attachment (Nylon head / Blade)
N: Guard extension
O: Shoulder belt: Harness with release mechanism.
P: Combi box spanner
Q: Goggles
R: Hex bar wrench
S: Blade cover
T: Handling instructions
WARNINGS AND SAFETY
INSTRUCTIONS
Pay special attention to statements preceded by the
following words:
WARNING
Indicates a strong possibility of severe personal injury or
loss of life, if instructions are not followed.
CAUTION
Indicates a possibility of personal injury or equipment
damage, if instructions are not followed.
NOTE
Helpful information for correct function and use.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-skid
safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
12
English
c) Prevent unintentional starting. Ensure the
switch is in the off -position before connecting
to power source and/or battery pack, picking up
or carrying the tool.
Carrying power tools with your fi nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.
A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may aff ect the power toolʼs operation. If
damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
b) Use power tools only with specifi cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modifi ed.
Damaged or modifi ed batteries may exhibit
unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or
excessive temperature.
Exposure to fi re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside
the specifi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
13
English
CORDLESS GRASS TRIMMER /
BRUSH CUTTER SAFETY WARNINGS
a) Do not use the machine in bad weather conditions,
especially when there is a risk of lightning. This
decreases the risk of being struck by lightning.
b) Thoroughly inspect the area for wildlife where the
machine is to be used. Wildlife may be injured by the
machine during operation.
c) Thoroughly inspect the area where the machine
is to be used and remove all stones, sticks, wires,
bones, and other foreign objects. Thrown objects can
cause personal injury.
d) Before using the machine, always visually inspect
to see that the cutter or blade and the cutter or
blade assembly are not damaged. Damaged parts
increase the risk of injury.
e) Follow instructions for changing accessories.
Improperly tightened blade securing nuts or bolts
may either damage the blade or result in it becoming
detached.
f) The rated rotational speed of the blade must be
at least equal to the maximum rotational speed
marked on the machine. Blades running faster than
their rated rotational speed can break and fl y apart.
g) Wear eye, ear, head and hand protection. Adequate
protective equipment will reduce personal injury by fl ying
debris or accidental contact with the cutting line or blade.
h) While operating the machine, always wear non-
slip and protective footwear. Do not operate the
machine when barefoot or wearing open sandals.
This reduces the chance of injury to the feet from contact
with the moving cutters or lines.
i) While operating the machine, always wear safety
footwear. Do not operate the machine when
barefoot or wearing open sandals. This reduces the
chance of injury to the feet from contact with a moving
cutter, line or blade.
j) While operating the machine, always wear long
trousers. Exposed skin increases the likelihood of injury
from thrown objects.
k) Keep bystanders away while operating the machine.
Thrown debris can result in serious personal injury.
l) Always use two hands when operating the machine.
Holding the machine with both hands will avoid loss of
control. (Fig. 2)
m) Hold the machine by the insulated gripping surfaces
only, because the cutting line or blade may contact
hidden wiring. Cutting line or blades contacting a "live"
wire may make exposed metal parts of the machine
"live" and could give the operator an electric shock.
n) Always keep proper footing and operate the
machine only when standing on the ground. Slippery
or unstable surfaces may cause a loss of balance or
control of the machine.
o) Do not operate the machine on excessively steep
slopes. This reduces the risk of loss of control, slipping
and falling which may result in personal injury.
p) When working on slopes, always be sure of your
footing, always work across the face of slopes,
never up or down and exercise extreme caution
when changing direction. This reduces the risk of
loss of control, slipping and falling which may result in
personal injury.
q) Keep all parts of the body away from the cutter,
line or blade when the machine is operating. Before
you start the machine, make sure the cutter, line
or blade is not contacting anything. A moment of
inattention while operating the machine may result in
injury to yourself or others.
r) Do not operate the machine above waist height.
This helps prevent unintended cutter or blade contact
and enables better control of the machine in unexpected
situations.
s) When cutting brush or saplings that are under
tension, be alert for spring back. When the tension
in the wood fi bres is released, the brush or sapling may
strike the operator and/or throw the machine out of
control.
t) Use extreme caution when cutting brush and
saplings. The slender material may catch the blade and
be whipped toward you or pull you off balance.
u) Maintain control of the machine and do not touch
cutters, lines or blades and other hazardous moving
parts while they are still in motion. This reduces the
risk of injury from moving parts.
v) When clearing jammed material or servicing the
machine, make sure the switch is off and the battery
pack is removed. Unexpected starting of the machine
while clearing jammed material or servicing may result in
serious personal injury.
w) Carry the machine with the machine switched off
and away from your body. Proper handling of the
machine will reduce the likelihood of accidental contact
with a moving cutter, line or blade.
x) When transporting or storing the machine, always
fi t the cover on metal blades. Proper handling of the
machine will reduce the likelihood of accidental contact
with the blade.
y) Only use replacement cutters, lines, cutting heads
and blades specifi ed by the manufacturer. Incorrect
replacement parts may increase the risk of breakage
and injury.
BLADE THRUST CAUSES AND
RELATED WARNINGS
Blade thrust is a sudden sideways, forward or backward
motion of the machine, which may occur when the blade
jams or catches on an object such as a sapling or a tree
stump. It can be violent enough to cause the machine and/or
operator to be propelled in any direction, and possibly lose
control of the machine.
Blade thrust and its related hazards can be avoided by
taking proper precautions as given below.
a) Maintain a fi rm grip with both hands on the machine
and position your arms to resist blade thrust.
Position your body to the left side of the machine.
Blade thrust can increase the risk of injury due to the
machine moving unexpectedly. Blade thrust can be
controlled by the operator if proper precautions are
taken.
b) If the blade binds, or when interrupting a cut
for any reason, switch the machine off and hold
the machine motionless in the material until the
blade comes to a complete stop. While the blade
is binding, never attempt to remove the machine
from the material or pull the machine backward
while the blade is in motion, otherwise blade thrust
may occur. Investigate and take corrective actions to
eliminate the cause of blade binding.
c) Do not use blunt or damaged blades. Blunt or
damaged blades increase the risk of jamming or
catching on an object, resulting in blade thrust.
d) Always maintain good visibility of the material
being cut. Blade thrust is more likely to occur in areas
where it is diffi cult to see the material being cut.
e) If you are approached by another person while
operating the machine, switch the machine off .
There is an increased risk of injury to other persons
being struck by the moving blade in the event of blade
thrust.
14
English
ADDITIONAL SAFETY WARNINGS
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Safe operation practices
● Training
a) Read the instructions carefully. Be familiar with the
controls and the correct use of the machine.
b) Never allow people unfamiliar with these instructions
or children to use the machine. Local regulations can
restrict the age of the operator.
c) Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
● Preparation
a) Before use check the supply and extension cord for
signs of damage or aging. If the cord becomes damaged
during use, disconnect the cord from the supply
immediately.
DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or worn.
b) Before use, always visually inspect the machine for
damaged, missing or misplaced guards or shields.
c) Never operate the machine while people, especially
children, or pets are nearby.
d) Never replace nylon head with metalic cutting means.
● Operation
a) Wear eye protection, stout shoes and long trousers at all
times while operating the machine.
b) Avoid using the machine in bad weather conditions
especially when there is a risk of lightning.
c) Use the machine only in daylight or good artifi cial light.
d) Never operate the machine with damaged guards or
shields or without guards or shields in place.
e) Switch on the motor only when the hands and feet are
away from the cutting means.
f) Always disconnect the machine from the power supply
(i.e. remove the plug from the mains or remove the
disabling device)
– whenever the machine is left user;
– before clearing a blockage;
– before checking, cleaning or working on the machine;
– after striking a foreign object to inspect the machine
for damage;
– if the machine starts to vivrate abnormally, for
immediately check.
g) Take care against injury to feet and hands from the
cutting means.
h) Always ensure that the ventilation openings are kept
clear of debris.
i) Never modify the unit/machine in any way. Do not use
your unit/machine for any job except that for which it is
intended.
j) If the unit striking a hard object or there appears to be
excessive vibration, inspect it carefully to check there is
no damage, cracks or deformation.
Using a tool that is damaged, cracked or deformed could
result in injury.
k) The guard extension is equipped with the knife.
Never place your hands near the knife.
I) Do not wear multiple belt harnesses or multiple shoulder
harnesses at the same time.
When wearing the shoulder belt, make sure that other
attachments do not interfere with the quick release
bracket of the shoulder belt.
● Maintenance, transport and storage
a) Disconnect the machine from the power supply (i.e.
remove the plug from the mains or remove the disabling
device) before carrying out maintenance or cleaning
work.
b) Use only the manufacturer’s recommended
replacement parts and accessories.
c) Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
d) When not in use, store the machine out of the reach of
children.
e) When transporting in a vehicle or storage, cover blade
with blade cover.
f) When cutting edges become dull, re-sharpen or fi le as
shown in the illustration or contact a HiKOKI Authorized
Service Center.
Incorrect sharpening may cause excessive vibration.
● KICKBACK DANGER (Fig. 3)
When using metal cutting attachments such as blades,
contact with obstacles such as trees or other hard
surfaces with the front or right portion of the spinning
attachment may force the unit to catch on an obstacle,
resulting in a kickback reaction towards the right side of
the operator.
Kickback may occur when the cutting attachment comes
into contact with tree stumps or rocks hidden behind
weeds. Always make sure there are no obstacles hidden
by weeds before starting work.
To minimize the danger of kickbacks when they do occur,
always position the unit to the right side of the body
during operation. With the operator properly positioned
as the cutting attachment rotates, this will reduce the
danger of the unit’s direct contact with the body.
PRECAUTIONS FOR CORDLESS
GRASS TRIMMER / BRUSH CUTTER
WARNING
1. Exercise patience in all work with the tool. And dress
properly to keep warm.
2. Plan all work ahead to prevent accidents.
3. Do not operate the tool at night or under bad weather
conditions when visibility is poor. And do not operate the
tool when it is raining or right after it has been raining.
Working on slippery ground could lead to an accident if
you lose your balance.
4. Inspect the cutting attachment before starting work.
Do not use the tool if the cutting attachment is cracked,
scarred or bent.
Make sure the cutting attachment is properly attached. A
cutting attachment that falls apart or comes loose during
operation could cause an accident.
5. Be sure to attach the guard before starting work.
Operating the tool without this parts could lead to injury.
6. Be sure to attach the handle before starting work. Make
sure it is not loose but properly attached before starting
work. Hold the handle fi rmly during work and do not
swing the tool around, but use the correct posture and
maintain your balance.
Losing your balance during work could lead to an injury.
7. Take care when starting the motor.
Place the tool on level ground.
Do not operate the tool within 15 m of people or animals.
Make sure that the cutting attachment does not come
into contact with the ground or trees and plants.
A careless start could lead to injury.
8. Do not secure the lock lever.
Accidentally pulling back the lever could lead to
unexpected injury.
9. Before leaving the tool, press the power switch to turn it
off .
15
English
10. Operate the tool with care near electric cables, gas pipes
and similar installations.
11. Look out for and remove empty cans, wire, stones or
other obstacles before starting work. And do not work
near tree roots or rocks.
Working in such areas could damage the cutting
attachment or lead to injury.
12. Never touch the cutting attachment during operation.
Also make sure it does not come into contact with your
hair, clothes, etc.
13. In the following situations, turn off the motor and check
that the cutting attachment has stopped rotating.
To move to another work area.
To remove rubbish or grass that has become stuck in the
tool.
To remove from the work area obstacles or the rubbish,
grass and chips generated by trimming.
To lay down the tool.
Doing this with the cutting attachment still rotating could
lead to unexpected accidents.
14. Do not use the tool within 15 m of another person.
When you work with someone else, maintain a distance
of more than 15 m.
Flying chips could lead to unexpected accidents.
When working on unstable surfaces like slopes, make
sure that your co-worker is not exposed to any hazards.
Use whistles or other means for calling the attention of
your co-workers.
15. When grass and other objects become entangled in the
cutting attachment, turn off the motor and make sure the
cutting attachment has stopped rotating before removing
them.
Removing objects from the cutting attachment when it is
still rotating will lead to injury.
Continuing operation when foreign matter is stuck in the
cutting attachment may lead to damage.
16. If the tool is operating poorly and produces strange noise
or vibrations, turn off the motor immediately and ask your
dealer to have it inspected and repaired.
Continued use under these conditions could lead to
injury or tool damage.
17. If you drop or bump the tool, inspect it carefully to check
there is no damage, cracks or deformation.
Using a tool that is damaged, cracked or deformed could
result in injury.
18. Secure the tool during vehicle transport to ensure that it
lies still.
Failure to heed this warning may result in an accident.
19. When transporting or moving the tool, hold the main pipe
with both hands, and keep the blade away from your
body when carrying.
20. Put the blade cover in the included tool bag so that it can
be used right away when needed, and always keep it
near the tool.
21. When transporting or storing the tool, remove the
battery, and remove the blade or cover it with the blade
cover.
22. When not working, remove the shoulder belt from the
tool.
23. Make sure that the battery is installed fi rmly. If it is at all
loose it could come off and cause an accident.
24. Do not use the product if the tool or the battery terminals
(battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
25. Keep the tool’s terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result in
smoke emission or ignition.
26. Always use the tool and battery at temperatures between
-5°C and 40°C.
27. Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
CAUTION
1. Do not turn on the cutting attachment for cutting objects
other than grass. Do not operate the tool in water puddles
and make sure that soil does not come into contact with
the cutting attachment.
2. The tool contains precision parts and should not be
dropped, exposed to strong impact or water.
The tool could be damaged or malfunction.
3. When the tool is to be stored after use or be transported,
remove the cutting attachment.
4. Do not expose the tool to insecticide and other
chemicals.
Such chemicals could cause cracking and other
damage.
5. Replace warning labels with new labels when they
become diffi cult to recognize or illegible and when they
start to peel.
Ask your dealer to provide the warning labels.
PRECAUTIONS FOR BATTERY AND
CHARGER (sold separately)
1. Always charge the battery at an ambient temperature
of 0–40°C. A temperature of less than 0°C will result in
over charging which is dangerous. The battery cannot
be charged at a temperature greater than 40°C.
The most suitable temperature for charging is that of
20–25°C.
2. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
3. Never disassemble the rechargeable battery or charger.
4. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
5. Do not dispose of the battery in fi re.
If the battery is burnt, it may explode.
6. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
7. Do not insert objects into the air ventilation slots of the
charger.
Inserting metal objects or fl ammable into the charger air
ventilation slots will result in an electrical shock hazard or
damage to the charger.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
16
English
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○ During work make sure that swarf and dust do not fall on
the battery.
○ Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
○ Do not store an unused battery in a location exposed to
swarf and dust.
○ Before storing a battery, remove any swarf and dust that
may adhere to it and do not store it together with metal
parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject the
battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery for a purpose other than those
specifi ed.
5. If the battery charging fails to complete even when a
specifi ed recharging time has elapsed, immediately stop
further recharging.
6. Do not put or subject the battery to high temperatures or
high pressure such as into a microwave oven, dryer, or
high pressure container.
7. Keep away from fi re immediately when leakage or foul
odor are detected.
8. Do not use in a location where strong static electricity
generates.
9. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
10. Do not immerse the battery or allow any fl uids to fl ow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in fi re or explosion. Store your
battery in a cool, dry place, away from combustible and
fl ammable items. Corrosive gas atmospheres must be
avoided.
11. Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you fi nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the fi rst time, do not use and return it to your
supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may occur
resulting in the risk of fi re. Please observe the following
matters when storing the battery.
○ Do not place electrically conductive cuttings, nails,
steel wire, copper wire or other wire in the storage
case.
○ Either install the battery in the power tool or store
by securely pressing into the battery cover until the
ventilation holes are concealed to prevent short-
circuits (See Fig. 4).
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please observe the
following precautions.
WARNING
Notify the transporting company that a package contains a
lithium-ion battery, inform the company of its power output
and follow the instructions of the transportation company
when arranging transport.
○ Lithium-ion batteries that exceed a power output of
100 Wh are considered to be in the freight classifi cation
of Dangerous Goods and will require special application
procedures.
○ For transportation abroad, you must comply with
international law and the rules and regulations of the
destination country.
Power Output
2 to 3 digit number
USB DEVICE CONNECTION
PRECAUTIONS (UC18YSL3)
When an unexpected problem occurs, the data in a USB
device connected to this product may be corrupted or lost.
Always make sure to back up any data contained in the USB
device prior to use with this product.
Please be aware that our company accepts absolutely no
responsibility for any data stored in a USB device that is
corrupted or lost, nor for any damage that may occur to a
connected device.
WARNING
○ Prior to use, check the connecting USB cable for any
defect or damage.
Using a defective or damaged USB cable can cause
smoke emission or ignition.
○ When the product is not being used, cover the USB port
with the rubber cover.
Buildup of dust etc. in the USB port can cause smoke
emission or ignition.
NOTE
○ There may be an occasional pause during USB
recharging.
○ When a USB device is not being charged, remove the
USB device from the charger.
Failure to do so may not only reduce the battery life
of a USB device, but may also result in unexpected
accidents.
○ It may not be possible to charge some USB devices,
depending on the type of device.
17
English
NAMES OF PARTS (Fig. 2–Fig. 36)
1Battery 31 Hanger
2Latch 32 Bracket
3Battery cover 33 Hook
4Terminals 34 Quick-release bracket
5Ventilation holes 35 Nylon head
6Push 36 Button
7Pull out 37 Wear limit mark
(2 marks)
8Insert 38 Cutter holder (A)
9Charge indicator lamp 39 25 mm diameter boss
10 Main pipe 40 Stopper pin
11 Grip side 41 Threaded fastener of
the gear case
12 Loop handle 42 Nylon head tightening
direction (left rotation)
13 M6 nuts 43 Nylon line
14 M6 x 43 bolts 44 Tap
15 Handle fi xture
(loop handle type) 45 Extends in 30 mm
increments
16 Handle location label 46 Tap/release
17 Handle right 47 Appropriate length
110–140 mm
18 Lever 48 Blade
19 Handle left 49 Cutter cover
20 Handle fi xture
(bike handlebars type) 50 Cutter holder (B)
21 M5 × 25 hex. Socket
bolts 51 Cutter holder cap
22 M6 × 25 hex. Socket
button bolts 52 Nut
23 Cover bracket 53 Power switch
24 Guard 54 Warning signal
25 Gear case 55 Mode switch
26 Guard extension 56 Mode Indicator lamp
27 Knife 57 Lock lever
28 Bolt 58 Grip
29 Shoulder belt 59 Battery level indicator
switch
30 Quick-release belt 60 Battery level indicator
lamp
61 Grease 69 U-shaped end
62 Screw hole of side 70 Groove
63 Cover 71 Direction to wind nylon
cord
64 Case 72 Eyelet line guide
65 Locking tab 73 While holding the reel
66 Press tabs (2 areas) 74 String the line through
the eyelet line guide
67 Reel 75 Locking holes of cover
(2 holes)
68 Stopper holes 76 Bolt (for Hanger)
SPECIFICATIONS
1. Power tool
Model CG36DC CG36DC(L)
Voltage 36 V
Pole type Straight type
Cutting capacity diameter 440 mm
Rotation direction Counterclockwise as seen
from above
No-load speed
Power 6000 /min
Auto 4700 /min
Eco 3000 /min
Operating time
under no load*
(BSL36B18)
Power 27 min
Auto 50 min
Eco 115 min
Battery available for this
tool** Multi volt battery
Weight*** 5.4 kg 5.2 kg
* When supplied rechargeable battery is fully charged
The data in the above table is provided only as an example.
Since ambient temperature, rechargeable battery
characteristics, etc. can vary widely the above should
only be used as a rough guideline. Conditions: When
using the blade, the mode switch is set to Power, Auto,
or Eco. (lever left ON all the time)
** AC/DC Adapter (ET36A) cannot be used. Existing
batteries (BSL3660/3626X/3626/3625/3620, BSL18 and
BSL14 series) cannot be used with this tool.
*** Weight: blade, guard and shoulder belt included
NOTE
Due to HiKOKI’s continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
2. Battery (sold separately)
Model BSL36B18
Voltage 36 V / 18 V (Automatic Switching*)
Battery capacity 4.0 Ah / 8.0 Ah
(Automatic Switching*)
* The tool itself will automatically switch over.
18
English
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 37.
Standard accessories are subject to change without notice.
APPLICATIONS
Trimming, scaling and mowing of weed.
CHARGING
Before using the power tool, charge the battery as follows.
<UC18YSL3 (sold separately)>
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (See Table 1).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 6 (on page 3).
3. Charging
When inserting a battery in the charger, charging will
commence and the charge indicator lamp will blink in
blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
Table 1: Indications of the charge indicator lamp
ON/OFF at 0.5 sec. intervals
(RED) Before charging*1
Lights for 0.5 sec. at intervals of
1 sec. (BLUE) Charged at less than
50%
Lights for 1 sec. at intervals of
0.5 sec. (BLUE) Charged at less than
80%
Lights continuously (BLUE) Charged at more than
80%
Lights continuously (Continuous
buzzer sound: about 6 sec.)
(GREEN) Charging complete
ON/OFF at 0.3 sec. intervals
(RED) Overheat standby*2
ON/OFF at 0.1 sec. intervals
(Intermittent buzzer sound;
about 2 sec.) (PURPLE) Charging impossible*3
NOTE
*1 If the red lamp continues to blink even after the charger
has been attached, check to confi rm that the battery has
been fully inserted.
*2 Battery overheated. Unable to charge.
Although charging will start once the battery has cooled
down even when left in situ, the best practice is to
remove the battery and allow it to cool down in a shaded,
well-ventilated location before charging.
*3 Malfunction in the battery or the charger
– Fully insert the battery.
– Check to confi rm that no foreign matter is stuck to
the battery mount or terminals. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 5 minutes rest until the next charging.
(2) Regarding the temperatures and charging time of the
battery. (See Table 2)
Table 2
Model UC18YSL3
Type of battery Li-ion
Charging voltage 14.4–18 V
Temperatures at which the
battery can be recharged 0°C–50°C
Charging time for
battery capacity,
approx.
(At 20°C)
1.5 Ah 15 min
2.0 Ah 20 min
2.5 Ah 25 min
3.0 Ah
20 min
(BSL1430C, BSL1830C:
30 min)
4.0 Ah 26 min
(BSL1840M: 40 min)
5.0 Ah 32 min
6.0 Ah 38 min
Charging time for
multi volt battery
capacity, approx.
(At 20°C)
1.5 Ah
(× 2 unit) 20 min
2.5 Ah
(× 2 unit) 32 min
4.0 Ah
(× 2 unit) 52 min
Number of battery cells 4–10
Charging voltage for USB 5 V
Charging current for USB 2 A
Weight 0.6 kg
NOTE
○ The recharging time may vary according to ambient
temperature and power source voltage.
○ If charging takes a long time
– Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
– Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
– If the cooling fan is not operating, contact a HIKOKI
Authorized Service Center for repairs.
4. Disconnect the charger's power cord from the
receptacle.
19
English
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a battery
is recharged immediately after use, its internal chemical
substance will deteriorate, and the battery life will be
shortened. Leave the battery and recharge it after it has
cooled for a while.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 5 3
Charging 6 3
Remaining battery indicator 26 7
Charging a USB device from a
electrical outlet 27-a 7
Charging a USB device and battery
from a electrical outlet 27-b 7
How to recharge USB device 28 7
When charging of USB device is
completed 29 7
Selecting accessories ―38
ASSEMBLY PROCEDURES
WARNING
Pull out battery before doing any assembly.
1. Installing of handle
(1) Loop handle type (Fig. 7)
Attach the handle to the main pipe with the angle towards
the grip side.
Adjust the location to the most comfortable position
before operation.
Make sure to securely attach the handle with the 2 bolts.
NOTE
Install the loop handle between the arrow marks on the
handle location label.
(2) Bike handle type (Fig. 8)
Remove the handle fi xture from the assembly.
Place the handle and attach the handle fi xture with four
bolts lightly. Adjust to appropriate position. Then attach it
fi rmly with the bolts.
NOTE
The bike handle can be adjusted by moving it forward to
the arrow mark on the handle location label.
2. Installing of guard
WARNING
○ If an incorrect or faulty guard is fi tted, this may cause
serious personal injury.
CAUTION
The guard extension is equipped with the knife. Be
careful with handling it.
Align the guard with the cover bracket and secure it to the
main pipe, using the bolt and cover bracket. (Fig. 9)
NOTE
○ The guard extension is already attached to the guard at
the time of purchase.
○ The cover bracket may come already mounted to the
gear case.
2-1 When using the semi-auto nylon head
When using a the nylon head, attach the guard extension
to the guard, then tighten the bolt. (Fig. 10)
2-2 When using the blade
WARNING
Remove the guard extension when using metal or plastic
blades. Failure to do so may result in injury or damage to
the guard.
NOTE
Wear gloves as the extension has the knife.
Loosen the bolt. Then push the three square tabs on
the guard one by one in order, and remove the guard
extension. (Fig. 11)
3. Installing the shoulder belt
WARNING
○ Be sure to attach the shoulder belt so that the grass
trimmer / brush cutter can be carried correctly.
○ If you get the feeling the tool is not operating normally,
turn off the motor immediately, remove the quick-release
bracket of the shoulder belt and remove the tool.
CAUTION
○ If you do not support the tool when you pull the quick-
release belt, it may fall causing injury or damage.
Hold the main pipe with one hand while you pull with the
other hand.
○ Make sure the quick-release function operates normally
before you start working.
○ Before attaching, check to confi rm that the belt is not cut,
frayed, or damaged.
○ Check to confi rm that the hook and hanger are neither
deformed nor damaged.
○ Once attached, press down on the main unit to confi rm
that the hook does not detach easily and that the
shoulder belt is not loose.
○ Check to confi rm that the quick release function operates
as it should.
(1) Place the shoulder belt on the shoulder as shown in
Fig. 12 and engage it with the hanger on the tool. Adjust
the shoulder belt to suitable length.
(2) To remove the tool from the shoulder belt, support the
tool by holding the main pipe with one hand and use
the other hand to pull the quick-release belt as shown in
Fig. 13 to free it from the bracket.
(3) To strap on the tool, insert the bracket in the hook and
insert the quick-release bracket over the hook and into
the wide opening of the bracket. (Fig. 14)
Gently pull the shoulder belt to make sure that it is
properly attached.
NOTE
You may need to adjust the position of the hanger to
balance the unit. To do so, loosen bolt and adjust the
position of hanger. After adjusting as necessary, make
sure to securely tighten the bolt. (Fig. 15)
20
English
4. Installation of cutting attachment
WARNING
○ Install the cutting attachment properly and securely as
instructed in the handling instructions.
If not attached properly or securely, it may come off and
cause serious and/or fatal injury.
○ Always use genuine HiKOKI cutting attachments and
metal fi ttings.
4.1 Installation of semi-auto nylon head
(1) Function
Automatically feeds more nylon cutting line when it is
tapped at low rpm (not greater than 4500 /min).
Specifi cations
Code
No.
Type of
attaching
screw
Direction of
rotation
Size of
attaching
screw
6696454 Female screw Counter-
clockwise
M10xP1.25-
LH
Applicable nylon cord
Cord diameter: Φ3.0 mm Length: 2 m
Cord diameter: Φ2.4 mm Length: 4 m
CAUTION
○ The case must be securely attached to the cover.
○ Check the cover, case and other components for cracks
or other damage.
○ Check the case and button for wear.
If the wear limit mark on the case is no longer visible or
there is a hole in the bottom of the button, change the
new parts immediately. (Fig. 16)
○ The nylon head must be securely mounted to the unit’s
gear case.
○ If the nylon head does not feed cutting line properly,
check that the nylon line and all components are properly
installed. Contact HiKOKI Authorized Service Centers if
you need assistance.
WARNING
For HiKOKI heads, use only fl exible, non-metallic line
recommended by the manufacturer. Never use wire or
wire ropes. They can break off and become a dangerous
projectile.
(2) Installation (Fig. 17)
Press the stopper pin of the gear case in order to lock the
cutter holder.
Install nylon head on gear case of tool. The mounting nut
is left-hand-threaded. Turn clockwise to loosen/counter-
clockwise to tighten.
NOTE
Since the cutter holder cap is not used here, keep it for
when a metal blade is used, if so equipped.
(3) Adjusting line length
Set the speed as low as possible and tap the button on
the ground. The nylon line will be drawn out about 30 mm
with each tap. (Fig. 18)
Also, you can extend the nylon line by hand but the
motor must be completely stopped. (Fig. 19)
Adjust the nylon line to the proper length of 110–140 mm
before each operation.
4.2 Installing the cutting blade
(1) Installation (Fig.20)
WARNING
○ When installing a cutting blade, make sure that there are
no cracks or any damage in it and that the cutting edges
are facing the correct direction.
○ Remove any surface grit from blade installation fi ttings
(cutter holder (A) (B), nut cover, nut). Failure to do so
may result in the loosening of nuts.
○ The protrusion of the cutter holder (A) may become
misaligned with the blade while tightening nut. Before
operation, make sure the blade has been properly
installed.
○ Rotate the blade by hand and make sure there is no
rocking or abnormal noise. Rocking may cause abnormal
vibrations or result in the loosening of nuts.
CAUTION
○ If your unit is equipped with protection cover under a
cutting blade, check the blade installation brackets for
wear or cracks before operation. If any damage or wear is
found, replace it, as it is an article of consumption.
○ You have to wear gloves when handling the cutting
blade.
NOTE
○ When installing cutter holder cap, be sure to set concave
side upward.
Press the stopper pin of the gear case in order to lock the
cutter holder. Please note that the cutter fi xing bolt or nut
has left-handed threads, (clockwise to loosen/ counter-
clockwise to tighten).
Tighten the fi xing bolt or nut with the box wrench.
OPERATION
WARNING
○ Do not operate the tool at night or under bad weather
conditions when visibility is poor.
○ Do not operate the tool when it is raining or right after it
has been raining.
○ Wear proper footwear to prevent slipping that could
cause you to lose your balance and fall.
○ Do not use the tool on steep slopes.
When cutting on slopes that are not so steep, cut by
moving towards the ridge.
○ Take care not to move the cutting attachment too close
to your feet.
○ Do not raise the cutting attachment above your knee
during cutting.
○ Do not use the tool where the cutting attachment may
come into contact with stones, tree and other obstacles.
○ A cutting attachment can injure while it continues to spin
after the motor is stopped. When the unit is turned off ,
make sure the cutting attachment has stopped before
the unit is set down.
○ Do not use the tool within 15 m of another person. When
you work with someone else, maintain a distance of
more than 15 m.
1. Insert the battery.
2. Turn on the tool. (Fig. 21-a)
○ Press the power switch on the handle, the power goes
on and the power lamp on the handle lights green.
○ Pressing the power switch a second time turns the
power off and the green lamp on the handle goes off .
○ While the lever is pulled, the power does not turn ON
when the power switch is pressed.
[Auto power off ]
When the power is turned on but the lever is not used for
5 seconds, the tool is automatically turned off . To turn
the tool on again, press the power switch a second time.
WARNING
Never leave the tool with the power on. This could result
in an accident.
3. Mode switch (Fig. 21-b)
The tool is equipped with three modes:
“Power Mode” “Auto Mode” “Eco Mode”.
Each time the mode switch is pressed, the operation
mode changes.
The set mode remains set even if the power is turned off .
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/