Makita EM408MP ユーザーマニュアル

EM408MP

EM409MP

EN Grass Trimmer Attachment ORIGINAL INSTRUCTION

MANUAL 7

PTBR Acessório para Aparador de

Grama MANUAL DE INSTRUÇÕES

ORIGINAL 17

ES Accesorio de Desbrozadora MANUAL DE

INSTRUCCIONES ORIGINAL 28

ZHCN 割草头组件原版使用说明书 39

ZHTW 割草機頭組件原始操作手冊 49

ID Alat Tambahan Pemotong

Rumput PETUNJUK PENGGUNAAN

ASLI 59

MS Pemasangan Pemangkas

Rumput MANUAL ARAHAN ASAL 70

VI   81

TH   91

FA   111

AR   119

Fig.1

12 1

2

3

4

5

11

10

9

8

Fig.2

1

4

3

5

2

Fig.3

1

4

2

3

Fig.4

1

2

Fig.5

1

32

4

2

5

6

Fig.6

2

3

1

Fig.7

2

1

7

2

3

4

5

6

Fig.8

1

2

3

Fig.9

1

Fig.10

1

4

23

5

Fig.11

1

4

23

5

Fig.12

1

Fig.13

1

2

3

Fig.14

1

Fig.15

3

Fig.12

3

1

2

Fig.16

1

750 mm 750 mm

100-300 mm

Fig.17

1

750 mm 750 mm

100-300 mm

Fig.18

1

Fig.19

Fig.20

4

1

2

4

3

5

6

4 m

100 mm

Fig.21

5

6

Fig.22

Fig.23

7ENGLISH

ENGLISH (Original instructions)

TABLE OF CONTENTS

SPECIFICATIONS....................................................... 7

SAFETY WARNINGS .................................................. 8

PARTS DESCRIPTION...............................................11

ASSEMBLY.................................................................11

OPERATION.............................................................. 14

MAINTENANCE......................................................... 14

TROUBLESHOOTING............................................... 16

SPECIFICATIONS

Model: EM408MP EM409MP

Dimensions: length x width x height

(without cutting tool) 880 mm x 320 mm x 196 mm 880 mm x 185 mm x 203 mm

Nylon cord diameter 2.0 mm

Applicable

cutting tool

and cutting

diameter

2-tooth blade

(P/N 197997-3) 230 mm -

3-tooth blade

(P/N 195298-3) 230 mm -

4-tooth blade

(P/N B-14118) 230 mm -

8-tooth blade

(P/N B-14130) 230 mm -

Nylon cutting head

(P/N 191D89-4) 300 mm 330 mm

Plastic blade

(P/N 198383-1) 255 mm

Gear ratio 14:19

Net weight 1.4 kg 1.2 kg

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may dier from country to country.

•Weight according to EPTA-Procedure 01/2014

Approved power unit

This attachment is approved to use only with the follow-

ing power unit(s):

•DUX60 Cordless multi function power head

•DUX18 Cordless multi function power head

•UX01G Cordless multi function power head

•EX2650LH Multi function power head

WARNING: Never use the attachment with

non-approved power unit. Non-approved combi-

nation may cause serious injury.

Symbols

The following symbols are used on the attachment and

this instruction manual. Understand these denitions.

Take Particular care and attention!

Read instruction manual.

Wear protective helmet, eye and ear

protection!

Wear eye and ear protection.

Protective gloves must be worn!

Wear sturdy boots with nonslip soles.

Steeltoed safety boots are recommended!

15m(50FT)Keep bystanders at least 15 m (50 ft) away.

Danger; be aware of thrown objects.

Kickback!

Top permissible tool speed

8ENGLISH

Never use metal blade.

Intended use

For EM408MP

This attachment is designed only for the purpose of

cutting grass, weed, bushes and undergrowth in con-

junction with an approved power unit. Never use the

attachment for the other purpose. Abusing the attach-

ment may cause serious injury.

For EM409MP

This attachment is designed only for the purpose of

trimming grass and light weed in conjunction with an

approved power unit. Never use the attachment for

the other purpose. Abusing the attachment may cause

serious injury.

WARNING: Read the instruction manual of

the attachment as well as this instruction manual

before using. Failure to follow the warnings and

instructions may result serious injury.

SAFETY WARNINGS

Grass trimmer safety warnings

WARNING: Read all safety warnings,

-

vided with this machine. Failure to follow all instruc-

tions listed below may result in re and/or serious

injury to the operator and/or bystanders.

Save all warnings and instruc-

tions for future reference.

The term “grass trimmer” and “machine” in the warnings

and precautions refer to the combination of the attach-

ment and the power unit.

The term “motor” in the warnings and precautions refers

to the engine or electric motor of the power unit.

General safety

1. First-time or inexperienced operator should

ask the dealer for training in all operation of

the machine. Never allow children, persons

with reduced physical, sensory or mental

capabilities or lack of experience and knowl-

edge or people unfamiliar with the instructions

to use the machine.

2. It is recommended only to lend the machine

to people who have proven to be experienced.

Always hand over the instruction manual.

3. Stay alert, watch what you are doing and use

common sense when operating the machine.

Do not use the machine while you are tired,



medication. A moment of inattention while oper-

ating the machine may result in serious personal

injury.

4. Avoid using the machine in bad weather

conditions especially when there is a risk of

lightning.

5. Follow your national and local regulation for

use of outdoor power machines.

Intended use of machine

This machine is only intended for cutting grass,

weeds, bushes and undergrowth. Never use the

machine for any other purpose such as edging or

hedge cutting. Use for unintended purpose may result

in serious injury.

Personal protective equipment

1. Always wear heavy, long pants, sturdy boots,

gloves, and a long-sleeve shirt. Do not wear

loose clothing, jewelry, short pants, sandals,

or go barefoot. Secure hair so it is above

shoulder level.

2. Always wear a helmet where there is a risk of

falling objects.

3. Always wear protective goggles to protect

your eyes from injury when using the machine.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

4. 

Exposure to noise can cause hearing loss.

5. Always wear sturdy shoes with a non-slip

sole. This protects your feet against injuries and

ensures a good footing.

6. Wear a dust mask as necessary.

7. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

9ENGLISH

Preparation before use

1. Before use, always check the machine is safe

for operation:

—Check for fuel leaks.

—Make sure all fasteners are in place and

secure.

—Replace damaged parts.

—Make sure the cutting tool is properly

installed and securely fastened.

—Make sure the cutting tool guard is prop-

erly attached in the position as described

in this manual.

—

and other control switch for smooth

action and proper function.

—Clean the handles for proper control of

the machine.

—Make sure the handles are installed as

described in this manual.

Failure to follow those instructions may cause

serious injury.

2. Use a sharp blade. Discard blades that are

bent, warped, cracked, broken, chipped or

damaged in any way. A dull blade is more likely

to snag and kickback.

3. 

blade properly. Improper xing parts can cause

the blade to y o and seriously injure the operator

and/or bystanders.

Electrical and battery safety

1. Do not expose the machine, battery, or charger

to rain or wet conditions. Water entering the tool

will increase the risk of electric shock.

2. Do not charge battery in rain, or in wet

locations.

3. Do not replace the battery in the rain.

Refueling

1. Stop the engine before refueling. Keep away



during refueling. Otherwise re and/or explosion

may result.

2. Refuel outdoors. Refueling in a closed room can

cause explosion of fuel vapor.

3. Avoid contact with fuel or engine oil. Do not



from the machine and/or ground immediately.

If fuel spills on your clothes, change it immedi-



4. After refueling, carefully tighten the fuel tank

cap and check for fuel leak. Move at least 3 m

(10 feet) away from the fueling source and site

before starting engine.

5. Only transport and store fuel in approved con-

tainers. Keep children away from the stored

fuel.

Starting up the machine

1. Keep children, bystanders and pets at least

15 m (50 feet) away, when starting up or

using the machine. Additionally, bystanders

should wear eye protection, as there is still a

risk of injury from thrown objects. Otherwise

bystanders' unexpected action or blade kickback

may cause serious injury to the operator and/or

bystanders.

2. Start and operate the machine only outdoors

in a well ventilated area. Operation in aconned

or poorly ventilated area can result in death due to

suocation or carbon monoxide poisoning.

3. Before starting, make sure that the cutting

tool has no contact with hard objects such as

branches, stones etc. as the cutting tool will

revolve when starting.

4. If the cutting tool rotates at idle, adjust the idle

speed so that it stops at idle. Otherwise uninten-

tional contact with moving cutting tool may result

in serious injury.

5. Stop the motor immediately if you notice any

trouble.

6. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the machine.

Transportation

1. Stop the motor during transport. Otherwise

unintentional start-up may cause injury.

2. When transporting the machine, always attach

the cover to the cutting blade. Contact with bare

blades results in injury.

3. Ensure safe position of the machine during car

transportation to avoid fuel leakage.

4. Lift the entire machine from the ground when

carrying the machine. Dragging the machine

causes fuel tank damage and fuel leakage, result-

ing in re.

Operation

1. Only use the machine in good light and visi-

bility. Use in the dark or poor visibility area may

cause unexpected accident.

2. Avoid using the machine when it is hard to

keep your balance, for example, working on a

steep surface or windy day.

3. During operation, never stand on an unstable

or slippery surface or a steep slope. During

the cold season, beware of ice and snow and

always ensure secure footing.

4. If you are approached, stop the motor.

Otherwise the rotating cutting tool may hit the

bystander and result in serious injury.

5. Clear the working area before operation.

Remove all objects such as rocks, broken

glass, nails, wire, or string, which can be

thrown or become entangled in the cutting

attachment. Foreign particles may damage the

cutting tool and can cause dangerous kickback.

10 ENGLISH

6. To control the machine steadily, do the follow-

ing during operation:

—

on your right side.

—Hang the machine on your shoulder(s)

with the shoulder harness.

—Ensure a safe footing. Never work on a

ladder or in a tree.

—Avoid over-reach.

—Keep cutting tool below waist level.

—Keep all parts of your body away from the

rotating cutting tool and hot surface.

Those action reduces the risk of injury.

7. If weeds or branches get caught between the

cutting tool and guard, always stop the motor

before clearing. Otherwise unintentional blade

rotation may cause serious injury.

8. Never drop or throw the machine, unless an

emergency. If the machine drops or hits some-

thing, immediately check for fuel leakage,

safety devices and other damages. Operating

an malfunctioned machine may cause injury and/

or re.

9. Inspect the cutting tool frequently, or immedi-

ately after it hits a stone or other hard objects.

If the cutting tool breaks during operation, the

broken piece may y and cause injury.

10. Stop the motor when inspecting, cleaning or

replacing the cutting tool. Otherwise the cutting

tool may rotate unexpectedly and result in serious

injury.

11. Maintain proper control until the cutting tool

stops completely, when stopping the motor or

releasing the throttle trigger. A coasting blade

can cause injury.

12. Before starting the cutting operation, wait until

the cutting tool attains enough speed for cut-

ting. It reduces the risk of kickback and entangling

weeds.

13. Take a rest to prevent loss of control caused

by fatigue. We recommend to take a 10 to

20-minute rest every hour.

14. Stop the motor and place it in safe location,

when resting or leaving the machine. It pre-

vents unexpected accident.

15. 

not put them onto combustible materials, while

the engine runs or just after stopping it, as

they are hot. Burn and/or re may result.

16. Do not operate the tool in bad weather or if

there is a risk of lightning.

Cutting Tools

1. Use a suitable cutting tool for your work.

—Nylon cutting heads (string trimmer heads)

are suitable for trimming lawn grass.

—Metal blades are suitable for cutting weeds,

high grasses, bushes, shrubs, underwood,

thicket, and the like.

Always use the cutting tool guard properly

suited for the cutting tool used.

2. When using a nylon cutting head, use only



manual. Never use wire or wirerope. They can

break o and become adangerous projectile.

3. Never use metal multi-piece pivoting chains,



manual. Otherwise serious injury may result.

4. When handling the metal blade, always wear

gloves and put the blade cover on the blade.

The blade can cut bare hands.

5. When using metal blades, avoid “kickback”

and always prepare for an accidental kickback.

See the section Kickback.

Kickback (blade thrust)

Kickback (blade thrust) may occur when the spin-

ning blade contacts an object that it does not imme-

diately cut. It can be violent enough to cause the

unit and/or operator to be propelled in any direc-

tion, and possibly lose control of the unit, resulting

in serious injury. Kickback can occur without warn-

ing if the blade snags, stalls or binds and is more



material being cut.

Kickback occurs particularly when applying the

blade segment between 12 and 2 o’clock to solids,

bushes and trees with 3 cm or larger diameter.

►Fig.1

To avoid kickback:

1. Apply the segment between 8 and 11 o’clock.

2. Swing the tool evenly in half-circle from right

to left, like using a scythe. This allows the

proper segment of blade to contact plants to be

cut.

3. Never apply the segment between 12 and 2

o’clock.

4. Never apply the segment between 11 and 12

o’clock and between 2 and 5 o’clock, unless

the operator is well trained and experienced

and does it at his/her own risk.

►Fig.2

5. Never use cutting blades close to solids, such

as fences, walls, tree trunks and stones.

6. Never use cutting blades vertically, for such

operations as edging and trimming hedges.

7. -

cult to see the object being cut.

Vibration

Exposing to excessive vibration injures blood ves-

sels or nervous system of the operator and causes



wrists: “Falling asleep” (numbness), tingling, pain,

stabbing sensation, or alteration of skin color or

of the skin. If any of these symptoms occur, see a

physician.



your hands warm during operation and well main-

tain the machine and accessories.

11 ENGLISH

Maintenance

1. Have your machine serviced by our authorized

service center using only identical replace-

ment parts. Use only identical spare parts and

accessories supplied by MAKITA. Incorrect

repair and poor maintenance can shorten the life

of the machine and increase the risk of accidents.

2. Never alter or remove any components of the

machine. It may cause re and/or serious injury.

3. After use, clean the machine and check all

screws and nuts for tightness.

4. Check the condition of the cutting tool, cutting

tool guard and shoulder harness. The cutting

blade must be sharp. Never straighten or weld

damaged cutting tools.

Storage

1. Before storing the machine, perform full clean-

ing and maintenance. Remove the battery

cartridge. Empty the fuel tank. Attach the cover

to the cutting blade.

2. Store the machine in a dry and high or locked

location out of reach of children.

3. Do not prop the machine against something,

such as a wall. Otherwise it may fall suddenly

and cause an injury.

Other instructions

1. Pay attention to the environment. Avoid unnec-

essary throttle operation for less pollution

and noise emissions. Adjust the carburetor

correctly.

2. Do not operate the engine with faulty exhaust



First Aid

1. 

box is available in the vicinity of the cutting

operations. Immediately replace any item



2. When asking for help, give the following

information:

—Place of accident

—What happened

—Number of injured persons

—Kind of injuries

—Your name

Additional safety instructions

1. To avoid accident, leave more than 15m (50 ft)

distance between operators when two or more

operators work in one area. Also, arrange a

person to observe the distance between oper-

ators. If someone or an animal enter the work-

ing area, immediately stop the operation.

2. Only use the cutting tools that are marked with

a speed equal or higher than the speed marked

on the tool.

3. Be sure to remove the cover on the cutting

blade before operation.

PARTS DESCRIPTION

EM408MP

►Fig.3: 1. Cap 2. Pipe 3. Protector (universal type)

4. Protector extension 5. Cutter

EM409MP

►Fig.4: 1. Cap 2. Pipe 3. Protector (narrow type)

4. Cutter

ASSEMBLY

WARNING: Before assembling or adjusting



the spark plug cap or battery cartridge. Otherwise

the cutting tool or other parts may move and result in

serious injury.

WARNING: Before handling cutting blade,

wear protective gloves. During the assembly or

adjustment, your ngers may contact with the cutting

blade and it may cause serious injury.

WARNING: When assembling or adjusting

the equipment, always put it down. Assembling or

adjusting the equipment in an upright position may

result in serious injury.

WARNING: Follow the warnings and precau-

tions in the chapter “SAFETY WARNINGS” and

the instruction manual of the power unit.

12 ENGLISH

Correct combination of the cutting tool and the protector

CAUTION:Always use the correct combination of cutting tool and protector. The wrong protector may

not protect you from ying debris and stones. It can also aect the balance of the tool and result in serious per-

sonal injury.

Model Cutting tool Protector

EM408MP Metal blade

(with nut, cup, and clamp washer) Protector (universal type)

Nylon cutting head / Plastic blade Protector (universal type) with protector extension

EM409MP Nylon cutting head / Plastic blade Protector (narrow type)

Installing the protector (cutting tool

guard)

WARNING: Do not use a cutting tool without

an appropriate protector at any time.

WARNING: Always use the cutting tool

with the correct combination of the protector.

Otherwise contact with a cutting tool may cause

serious injury.

NOTICE:Periodically tighten the bolts on the

protector. Tighten the right and left bolts evenly

so that the gap between the clamp and the protec-

tor is constant.

Protector (universal type)

CAUTION:Make sure to push in the protec-

tor extension until it is fully inserted. Otherwise

the protector extension may fall and result in personal

injury.

CAUTION:Be careful not to injure your-

self with the cutter mounted on the protector

extension.

Fix the protector to the clamp with bolts.

►Fig.5: 1. Clamp 2. Protector

To install the protector extension, insert the protector

extension to the protector and then snap the clips on.

Make sure that the tabs on the protector extension t

into the slots on the protector.

►Fig.6: 1. Protector (universal type) 2. Clip

3. Protector extension 4. Cutter (inside)

5. Slot 6. Tab

To remove the protector extension from the protector,

unclasp the clips and pull the protector extension out.

NOTE: The cutter on the protector extension keeps

the nylon cord best length for cutting.

Protector (narrow type)

CAUTION:Be careful not to injure yourself

with the cutter mounted on the protector.

Attach the protector to the clamp using bolts.

►Fig.7: 1. Clamp 2. Protector 3. Cutter

NOTE: The cutter on the protector keeps the nylon

cord best length for cutting.

Installing the cutting tool

CAUTION:Be sure to use genuine MAKITA

cutting tools.

CAUTION:Be sure to remove the hex

wrench after installation.

NOTE: When installing the cutting tool, turn the tool

upside down for ease of the procedure.

13 ENGLISH

Installing the metal blade

For EM408MP

CAUTION:When handling the metal blade,

always wear gloves and put the blade cover on

the blade.

CAUTION:The outside diameter of the metal





CAUTION:The metal blade must be well

polished, free of cracks or breakage. If the metal

blade hits against a stone during operation, stop

the motor and check the blade immediately.

CAUTION:Polish or replace the metal blade

every three hours of operation.

CAUTION:Always use the supplied

wrench(es) to remove or to install the blade.

Applicable blade

Metal blade (2-tooth)

Metal blade (3-tooth)

Metal blade (4-tooth)

Metal blade (8-tooth)

1. Make sure that the receive washer is attached to

the shaft.

2. Insert the hex wrench through the hole in the gear

case to lock the shaft. Rotate the shaft until the hex

wrench is fully inserted.

3. Mount the metal blade onto the receive washer.

4. Install the clamp washer and cup, and then tighten

the nut securely.

Tightening torque: 16 - 23 N• m

5. Remove the hex wrench.

►Fig.8: 1. Nut 2. Cup 3. Clamp washer 4. Metal blade

5. Receive washer 6. Shaft 7. Hex wrench

►Fig.9: 1. Socket wrench 2. Hex wrench 3. Tighten

Make sure that the arrows on the blade and protector

indicate the same way.

►Fig.10: 1. Arrow

To remove the metal blade, follow the installation proce-

dure in reverse.

NOTE: The resin part on the blade fastening nut

wears out in course of time. Replace the nut if there

appears any wear or deformation.

Installing the nylon cutting head

CAUTION:If the nylon cutting head hits

against a stone during operation, stop the motor

and check the nylon cutting head immediately.

►Fig.11: 1. Nylon cutting head 2. Receive washer

3. Shaft 4. Hex wrench 5. Tighten

1. Make sure that the receive washer is attached to

the shaft.

2. Insert the hex wrench through the hole in the gear

case.

3. Screw the nylon cutting head onto the shaft.

4. After installing nylon cutting head, remove the hex

wrench.

To remove the nylon cutting head, turn it clockwise

while holding the receive washer with the hex wrench.

Installing plastic blade

Optional accessory

CAUTION:If the plastic blade accidentally

impacts a rock or hard object during operation,

stop the tool and inspect for any damage. If the

plastic blade is damaged, replace it immediately.

Use of a damaged cutting tool could result in serious

personal injury.

CAUTION:Be sure to remove the hex

wrench after installation.

NOTICE:Be sure to use genuine Makita plastic

blade.

►Fig.12: 1. Plastic blade 2. Receive washer 3. Shaft

4. Hex wrench 5. Tighten

1. Make sure that the receive washer is attached to

the shaft.

2. Insert the hex wrench through the hole on the gear

case and rotate the spindle until the spindle is locked.

3. Place the plastic blade onto the threaded spindle

directly and tighten.

4. Remove the hex wrench.

To remove the plastic blade, turn it clockwise while hold-

ing the receive washer with the hex wrench.

14 ENGLISH

Mounting the attachment pipe

CAUTION:Always check that the attach-

ment pipe is secured after installation. Improper

installation may cause the attachment falling o from

the power unit and cause personal injury.

Mount the attachment pipe to the power unit.

1. Turn the lever of the power unit toward the attach-

ment side.

►Fig.13: 1. Lever

2. Remove the cap of the attachment. Align the pin

with the arrow mark and insert the attachment pipe until

the release button pops up.

►Fig.14: 1. Release button 2.Arrow mark 3. Pin

3. Turn the lever toward the power unit side.

►Fig.15: 1. Lever

Make sure that the surface of the lever is parallel to the

pipe.

To remove the pipe, turn the lever toward the attach-

ment side and pull the pipe out while pressing down the

release button.

►Fig.16: 1. Release button 2. Lever 3. Pipe

OPERATION

WARNING: Follow the warnings and precau-

tions in the chapter “SAFETY WARNINGS” and

the instruction manual of the power unit.

WARNING: If the cutting tool moves at

idle, adjust the idle speed of the engine down.

Otherwise you cannot stop the cutting tool by throttle

o and it may cause serious injury.

Adjusting the hanger position and

shoulder harness

For DUX60 Cordless multi function power head,

EX2650LH Multi function power head

WARNING: Do not use the tool if you cannot

adjust the hanger position and shoulder harness

length within the range as illustrated. Using the

tool with improper weight balance may bring the

cutting tool upward and result in personal injury.

When replacing an accessory with another, the weight

balance of the equipment may change. In such case,

adjust the hanger position and shoulder harness length

as follows.

►Fig.17: 1. Hanger

To change the hanger position, loosen the xing screw

on the hanger and then move the hanger.

Adjust the hanger position and shoulder harness length

so that:

•the hanger positions 750 mm or higher from the

ground,

•the cutting tool positions 100 mm to 300 mm high

from the ground and,

•the unguarded part of cutting tool is horizontally

750 mm or further away from the hanger.

After adjusting the hanger position, tighten the screw

with a wrench or screwdriver (depending on the power

unit) securely.

Adjusting the shoulder harness

For DUX18/UX01G Cordless multi function power

head

WARNING: Do not use the tool if you cannot

adjust the shoulder harness length within the

range as illustrated. Using the tool with improper

weight balance may bring the cutting tool upward and

result in personal injury.

When replacing an accessory with another, the weight

balance of the equipment may change. In such case,

adjust the shoulder harness length as follows.

►Fig.18: 1. Hanger

Adjust the shoulder harness length so that:

•the hanger positions 750 mm or higher from the

ground,

•the cutting tool positions 100 mm to 300 mm high

from the ground and,

•the unguarded part of cutting tool is horizontally

750 mm or further away from the hanger.

Using a nylon cutting head

During operation, use the tip of the nylon cutting cord

for cut. As the nylon cutting cord is worn and shortened

with the cutting operation, the operator needs to feed it

manually. To feed the nylon cutting cord, tap the nylon

cutting head against the ground while rotating.

NOTE: If the nylon cutting cord does not feed out,

rewind it. Refer to the chapter “MAINTENANCE.”

MAINTENANCE

WARNING:Before inspecting or maintaining



the spark plug cap or battery cartridge. Otherwise

the cutting tool or other parts may move and result in

serious injury.

WARNING: When inspecting or maintaining

the equipment, always put it down. Assembling or

adjusting the equipment in an upright position may

result in serious injury.

WARNING: Follow the warnings and precau-

tions in the chapter “SAFETY WARNINGS” and

the instruction manual of the power unit.

NOTICE:Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

15 ENGLISH

Overall inspection

•Tighten loose bolts, nuts and screws.

•Check for damaged parts and blades. Ask our

authorized service center to replace them if

necessary.

Resharpening the cutting tool

WARNING: Do not resharpen cutting blades

by yourself. Manual resharpening unbalances a

cutting blade and it can cause vibrations and damage

to the equipment.

Ask Makita authorized service center to resharpen and

rebalance blunt cutter blades.

Lubricating moving parts

NOTICE:Follow the instruction of the fre-

quency and amount of grease supplied. Otherwise

insucient lubrication may damage moving parts.

Gear case:

CAUTION:Do not apply grease when the

gear case is hot. Hot gear case can cause burn

injury.

Apply grease (Shell Alvania 1 or 2, or equivalent) to the

gear case through the grease hole approximately every

30 working hours.

►Fig.19: 1. Grease hole

Drive axle:

Apply grease (Shell Alvania 1 or 2, or equivalent) to the

drive axle approximately every 30 working hours.

►Fig.20

NOTE: Genuine Makita grease may be purchased

from your local Makita dealer.

Replacing the nylon cord

WARNING: Use only the nylon cord with



Never use heavier line, metal wire, rope or the

like. Failure to do so may cause damage to the tool

and result in serious personal injury.

WARNING: Always remove the nylon cutting

head from the tool when replacing the nylon cord.

WARNING: Make sure that the cover of the

nylon cutting head is secured to the housing

properly as described in this instruction manual.

Failure to properly secure the cover may cause the

nylon cutting head to y apart resulting in serious

personal injury.

Replace the nylon cord if it is not fed any more. The

method of replacing the nylon cord varies depending on

the type of the nylon cutting head.

96-M10L

►Fig.21

Replacing the plastic blade

Replace the blade if it is worn out or broken.

►Fig.22

When installing the plastic blade, align the direction of

the arrow on the blade with that of the protector.

Storage

WARNING: Follow the warnings and precau-

tions in the chapter “SAFETY WARNINGS” and

the instruction manual of the power unit.

When storing the attachment separated from the power

unit, put the cap onto the end of the shaft.

►Fig.23

Interval of inspection and maintenance

Operating hour Before

Operation Daily (10h) 30h

Whole unit Visually inspect for

damaged parts - -

All xing screws and

nuts Tighten - -

Gear case Supply grease - -

Drive axle Supply grease - -

Cutter blade Visually inspect for

damage -

Power unit Refer to the instruction manual of the power unit

16 ENGLISH

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection rst. If you nd aproblem that is not explained in the man-

ual, do not attempt to dismantle the machine. Instead, ask Makita Authorized Service Centers, always using Makita

replacement parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Motor does not start. -Refer to the instruction manual of the power unit.

Motor stops soon. -Refer to the instruction manual of the power unit.

Motor speed does not increase. -Refer to the instruction manual of the power unit.

Cutting tool does not rotate.

Stop the motor immediately. Loose attachment of the cutting tool Tighten securely.

Cutting tool caught a twig. Remove foreign matter

Abnormal drive system Contact an authorized service center for repairs.

Main unit vibrates abnormally.

Stop the motor immediately. Broken, bent or worn cutting tool Replace the cutting tool.

Loose attachment of the cutting tool Tighten securely.

One end of nylon cutting cord has been

broken and the nylon cutting head got

unbalanced.

Feed the nylon cutting cord with tapping the nylon

cutting head on the ground.

Irregular attachment of cutting tool Attach properly.

Abnormal drive system Contact an authorized service center for repairs.

Cutter blade does not stop imme-

diately.

Stop the motor immediately.

The power unit does not work properly. Refer to the instruction manual of the power unit.

The nylon cutting cord does not feed. The cord is used up or tangled in the

spool. Rewind the cord.

The nylon cutting cord is not cut o at

the correct length. The cord cutter on the protector is

damaged or missing. Contact an authorized service center for repairs.

The cord extends past the protector. Rewind the cord.

17 PORTUGUÊS DO BRASIL

PORTUGUÊS DO BRASIL (Instruções originais)

CONTEÚDO

ESPECIFICAÇÕES ................................................... 17

AVISOS DE SEGURANÇA........................................ 18

DESCRIÇÃO DAS PEÇAS........................................ 22

MONTAGEM.............................................................. 22

OPERAÇÃO .............................................................. 24

MANUTENÇÃO......................................................... 25

SOLUÇÃO DE PROBLEMAS.................................... 27

ESPECIFICAÇÕES

Modelo: EM408MP EM409MP

Dimensões: comprimento x largura x altura

(sem a ferramenta de corte) 880 mm x 320 mm x 196 mm 880 mm x 185 mm x 203 mm

Diâmetro do o de náilon 2,0 mm

Ferramenta de

corte aplicável

e diâmetro de

corte

Lâmina de 2 dentes

(P/N 197997-3) 230 mm -

Lâmina de 3 dentes

(P/N 195298-3) 230 mm -

Lâmina de 4 dentes

(P/N B-14118) 230 mm -

Lâmina de 8 dentes

(P/N B-14130) 230 mm -

Cabeçote de corte de náilon

(P/N 191D89-4) 300 mm 330 mm

Lâmina de plástico

(P/N 198383-1) 255 mm

Relação de transmissão 14:19

Peso líquido 1,4 kg 1,2 kg

• Em função do nosso contínuo programa de pesquisa edesenvolvimento, as especicações que constam neste

manual estão sujeitas amudanças sem aviso prévio.

• As especicações podem diferir de país para país.

•Peso de acordo com o Procedimento 01/2014 da EPTA

Ferramenta aprovada

Este implemento está aprovado para ser usado apenas

com as seguintes ferramentas:

•Ferramenta multifuncional a bateria DUX60

•Ferramenta multifuncional a bateria DUX18

•Ferramenta multifuncional a bateria UX01G

•Ferramenta multifuncional EX2650LH

AVISO: Nunca use o implemento com ferra-

mentas não aprovadas. A combinação não apro-

vada pode causar ferimentos graves.

Símbolos

Os seguintes símbolos são usados no implemento e

neste manual de instruções. Entenda essas denições.

Tenha especial cuidado e atenção!

Leia o manual de instruções.

Use capacete, proteção visual e auditiva!

Use proteção ocular e auditiva.

Use luvas de proteção!

Use botas resistentes com solado antider-

rapante. Recomenda-se o uso de botas

com biqueira de aço!

15m(50FT)Mantenha outras pessoas afastadas a uma

distância de pelo menos 15 m.

Perigo! Tome cuidado, pois objetos podem

ser lançados na sua direção e de outras

pessoas.

Recuo!

Velocidade máxima permitida da

ferramenta

18 PORTUGUÊS DO BRASIL

Nunca use lâminas de metal.

Indicação de uso

Para o modelo EM408MP

Este implemento se destina somente ao corte de

grama, erva daninha, mato e vegetação rasteira em

conjunto com aferramenta aprovada. Nunca use o

implemento para outra nalidade. Abusar do imple-

mento pode causar ferimentos graves.

Para o modelo EM409MP

Este implemento se destina somente a aparar grama

eervas daninhas pequenas em conjunto com aferra-

menta aprovada. Nunca use o implemento para outra

nalidade. Abusar do implemento pode causar ferimen-

tos graves.

AVISO: Leia o manual de instruções do

implemento e também este manual de instruções

antes de usá-los. O descumprimento destos avisos

einstruções pode provocar ferimentos sérios.

AVISOS DE SEGURANÇA

Avisos de segurança para o

aparador de grama

AVISO: Leia todos os avisos de segurança,

-

cidos com esta máquina. O descumprimento das

instruções descritas abaixo pode resultar em incêndio

e/ou ferimentos graves no operador e/ou em pessoas

próximas.

Guarde todos os avisos e instru-

ções para consultas futuras.

Os termos “aparador de grama” e“máquina” nos avisos

e precauções referem-se à combinação do acessório

com a ferramenta.

O termo “motor” nos avisos e precauções refere-se ao

motor acombustão ou elétrico da ferramenta.

Segurança geral

1. Operadores iniciantes ou inexperientes

devem solicitar treinamento nas operações

da máquina ao revendedor. Nunca permita

que crianças, pessoas com capacidade física,

sensorial ou mental reduzida ou falta de expe-

riência e conhecimento, tampouco pessoas

não familiarizadas com as instruções, usem a

máquina.

2. Recomenda-se emprestar a máquina somente

a pessoas com experiência comprovada.

Empreste sempre acompanhada do manual de

instruções.

3. Mantenha-se alerta, preste atenção ao que

estiver fazendo e utilize bom senso quando

operar a máquina. Não use a máquina se

estiver cansado, indisposto, ou ainda sob



Um instante de desatenção durante a operação

da máquina pode resultar em ferimentos pessoais

graves.

4. Evite usar a máquina em condições climáti-

cas hostis, especialmente se houver risco de

raios.

5. Siga suas regulamentações federais e locais

sobre o uso de máquinas motorizadas ao ar

livre.

Uso pretendido da máquina

Esta máquina se destina somente ao corte de

grama, ervas daninhas, mato e vegetação rasteira.

-

dade, tal como o corte de bordaduras ou de cercas

vivas. Ouso para nalidades não indicadas pode

resultar em ferimentos sérios.

Equipamentos de proteção pessoal

1. Use sempre calças compridas grossas, botas

resistentes, luvas e camisa de manga com-

prida. Não use roupas folgadas, acessórios,



Prenda o cabelo acima da altura do ombro.

2. Use sempre um capacete em locais onde

houver risco de objetos caírem de locais altos.

3. Quando usar a máquina, use sempre os óculos

de segurança para proteger os olhos contra

ferimentos. Os óculos de segurança devem

atender aos requisitos das normas ANSI Z87.1

nos EUA, EN 166 na Europa, ou AS/NZS 1336

na Austrália/Nova Zelândia. Na Austrália/Nova

Zelândia, também é exigido por lei o uso de

um protetor facial para proteger o rosto.

É responsabilidade do empregador garantir

que os operadores da ferramenta e as outras

pessoas nas imediações da área de trabalho

usem os equipamentos protetores de segu-

rança apropriados.

4. Use proteção auditiva, tal como protetores

auriculares tipo concha. A exposição a ruídos

pode causar perda auditiva.

5. Use sempre sapatos resistentes, com solado

antiderrapante. Eles protegem os pés contra

lesões egarantem que estejam rmes no chão.

19 PORTUGUÊS DO BRASIL

6. Quando necessário, use uma máscara contra

poeiras.

7. Use equipamentos de proteção individual. Use

sempre óculos de proteção. Equipamentos de

proteção, como máscara contra pó, sapatos de

segurança antiderrapantes, capacete de segu-

rança e protetores auditivos, reduzem lesões

pessoais quando usados conforme exigido pelas

condições.

Preparação antes de utilizar

1. 

em condições seguras para operação:

—

combustível.

—

estão instalados e seguros.

—

—

corte está corretamente instalada e presa

com segurança.

—-

menta de corte está corretamente insta-

lada na posição descrita neste manual.

—-

vanca de travamento e outras chaves de

controle estão operando sem problemas

e funcionando corretamente.

—Limpe as empunhaduras para poder

controlar a máquina adequadamente.

—

estão instaladas conforme descrito neste

manual.

O descumprimento destas instruções pode provo-

car ferimentos sérios.

2. 

estiverem deformadas, empenadas, quebra-



Uma lâmina cega tem mais chances de car presa

e causar um recuo.

3. Use sempre todas as peças requeridas para

montar a lâmina corretamente. Peças mal ins-

taladas podem fazer com que alâmina seja arre-

messada ecause ferimentos sérios no operador

e/ou em pessoas próximas.

Segurança elétrica e da bateria

1. Não exponha a máquina, a bateria ou o carre-

gador à chuva ou umidade.Aentrada de água

na ferramenta aumenta orisco de choque elétrico.

2. Não carregue a bateria na chuva ou em locais

úmidos.

3. Não substitua a bateria na chuva.

Reabastecimento

1. Desligue o motor antes de reabastecer.

Mantenha-se afastado de chamas abertas e

faíscas. Nunca fume durante o reabasteci-

mento. Pois isso pode resultar em incêndio e/ou

explosões.

2. Reabasteça ao ar livre. O reabastecimento em

ambientes fechados pode causar explosão dos

vapores de combustível.

3. Evite o contato com o combustível ou o óleo

de motor. Não inale vapores de combustível.

Em caso de derramamento de combustível

ou óleo, limpe imediatamente o material der-

ramado para removê-lo da máquina e/ou do

chão. Se algum combustível derramado atingir

suas roupas, troque-as imediatamente para

impedir que se incendeiem.

4. Depois de reabastecer, aperte cuidadosamente



se há vazamentos. Afaste-se a uma distância

de pelo menos 3 m da fonte e do local do rea-

bastecimento antes de ligar o motor.

5. Transporte e armazene combustível somente

em recipientes aprovados. Mantenha o com-

bustível armazenado afastado de crianças.

Para ligar a ferramenta

1. Mantenha crianças, outras pessoas e animais

de estimação afastados a uma distância de

pelo menos 15 m ao ligar ou usar a máquina.

Além disso, pessoas próximas devem usar

proteção para os olhos, uma vez que existe

risco de ferimentos causados por objetos

arremessados. Do contrário, as ações inespera-

das de pessoas próximas ou um recuo da lâmina

podem causar ferimentos graves no operador e/

ou em pessoas próximas.

2. Ligue e opere a máquina somente ao ar livre,

em áreas bem ventiladas. A operação em locais

connados ou mal ventilados pode resultar em

morte por asxia ou envenenamento por monó-

xido de carbono.

3. 

que a ferramenta de corte não está em contato

com objetos duros, como galhos de árvore,

pedras, etc., pois ela irá girar quando for

ligada.

4. Se a ferramenta de corte girar em marcha

lenta, ajuste a velocidade de marcha lenta para

que ela pare na marcha lenta. Do contrário, o

contato acidental com a ferramenta de corte em

movimento pode resultar em ferimentos graves.

5. Desligue o motor imediatamente se perceber

algo anormal.

6. 

tubulações de água, tubulações de gás, etc.



uso da máquina.

Transporte

1. Desligue o motor durante o transporte. Do

contrário, oacionamento acidental pode provocar

ferimentos.

2. Ao transportar a máquina, coloque sempre a

capa na lâmina de corte. O contato com a lâmina

descoberta resulta em ferimentos.

3. -

ção segura ao transportá-la em um veículo

para evitar vazamentos de combustível.

4. Levante a máquina do chão totalmente ao

transportá-la manualmente.Arrastar amáquina

pode causar danos ao tanque de combustível e

vazamentos de combustível, resultando em um

incêndio.

20 PORTUGUÊS DO BRASIL

Operação

1. Somente utilize a máquina em boas condições

de iluminação e visibilidade. O uso no escuro

ou em áreas de pouca visibilidade pode causar

acidentes inesperados.

2. Evite usar a máquina quando for difícil manter

o equilíbrio, como por exemplo, trabalhando

em uma superfície íngreme ou em dias com

muito vento.

3. 

uma superfície instável ou escorregadia, nem

em um declive acentuado. Durante os meses

mais frios, tome cuidado com gelo e neve e



assentados no chão.

4. Se alguém se aproximar de você, desligue o

motor. Do contrário, aferramenta de corte em

rotação poderá atingir essa pessoa eprovocar

ferimentos sérios.

5. Limpe a área de trabalho antes da operação.

Remova todos os objetos que puderem ser

-

rio de corte, tais como pedras, cacos de vidro,

 Partículas estranhas

podem danicar aferramenta de corte eprovocar

um recuo perigoso.

6. 

seguinte durante a operação:

—

ambas as mãos, mantendo-a à sua

direita.

—Pendure a máquina em seu(s) ombro(s)

usando a correia de ombro.

—

chão. Nunca trabalhe em uma escada ou

em cima de uma árvore.

—Evite se esticar além do ponto de equilí-

brio para alcançar pontos distantes.

—Mantenha a ferramenta de corte abaixo

do nível da cintura.

—Mantenha todas as partes do corpo afas-

tadas da ferramenta de corte em rotação

e de superfícies quentes.

Essas ações reduzem o risco de ferimentos.

7. 

entre a ferramenta de corte e a proteção, desli-

gue o motor antes de retirá-los. Do contrário, a

rotação acidental da lâmina pode causar ferimen-

tos graves.

8. Nunca derrube ou jogue a máquina, exceto

durante uma emergência. Se a máquina cair ou

-

sitivos de segurança e se existem vazamentos

de combustível ou outros danos. A operação de

uma máquina defeituosa pode provocar ferimen-

tos e/ou incêndios.

9. Inspecione a ferramenta de corte com fre-

quência, ou imediatamente após ela atingir

uma pedra ou outros objetos rígidos. Se a

ferramenta de corte quebrar durante a operação,

opedaço quebrado poderá ser arremessado e

provocar ferimentos.

10. Desligue o motor ao inspecionar, limpar ou

trocar a ferramenta de corte. Do contrário, a

ferramenta de corte pode girar inesperadamente e

provocar ferimentos sérios.

11. Mantenha o controle apropriado até a ferra-

menta de corte parar completamente depois

de desligar o motor ou soltar o gatilho do

acelerador. Uma lâmina girando inercialmente

pode provocar ferimentos.

12. Antes de iniciar a operação de corte, aguarde

até que a ferramenta de corte atinja uma velo-

 Isso reduzirá o

risco de recuos ou do enroscamento de ervas

daninhas.

13. Descanse para evitar perda de controle cau-

sada por cansaço. Recomendamos tirar de 10 a

20 minutos de descanso a cada hora de trabalho.

14. Desligue o motor e coloque a máquina em

um local seguro ao descansar ou parar de

usar a máquina. Fazer isso previne acidentes

inesperados.

15. Não toque no motor nem no silenciador, nem

os coloque sobre materiais combustíveis

enquanto o motor estiver funcionando ou logo

após desligá-lo, pois estarão quentes. Poderá

ocorrer queimaduras e/ou um incêndio.

16. Não use a ferramenta durante intempéries ou

quando houver risco de relâmpagos.

Ferramentas de corte

1. Use uma ferramenta de corte adequada ao seu

trabalho.

— Os cabeçotes de corte de náilon (cabeçotes

de aparador de grama) são adequados para

aparar gramados.

— As lâminas metálicas são adequadas para

o corte de ervas daninhas, gramados altos,

mato, arbustos, vegetação rasteira, moitas e

similares.

Use sempre a proteção adequada à ferramenta

de corte utilizada.

2. Quando utilizar um cabeçote de corte de



metálicos recomendados neste manual. Nunca

use arames ou cabos de aço. Esses materiais

podem quebrar ese tornar projéteis perigosos.

3. Nunca use correntes articuladas de elos múl-

tiplos, facas articuladas ou lâminas não reco-

mendadas neste manual. Do contrário, podem

ocorrer ferimentos sérios.

4. Quando manusear a lâmina metálica, use sem-

pre luvas e coloque a capa da lâmina nesta. A

lâmina pode cortar as mãos desprotegidas.

5. Quando usar lâminas metálicas, evite

“recuos”, e esteja sempre preparado para um

recuo acidental. Consulte a seção Recuo.

ページが読み込まれています...

Makita EM408MP ユーザーマニュアル

Makita EM408MP ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント