Korenix JetNet 2005f Quick Installation Manual
- カテゴリー
- ネットワークスイッチ
- タイプ
- Quick Installation Manual
A Beijer Electronics Group Company
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
Package Check List
Unpack the box, you will find
JetNet 2005/2005f Switch
Quick Installation Guide
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
Overview
JetNet 2005/2005f Industrial Ethernet Switch, conforming IEEE 802.3 and 802.3u
standard, supports 5 10/100Base TX (JetNet 2005) or 4 10/100TX plus one
100FX Ethernet port (JetNet 2005f). JetNet 2005/2005f adopts slim industrial
design to save rail space of compact system requirement. In order to survive
under harsh environment, JetNet 2005/2005f chooses industrial-grade aluminum
case with IP30 standard protection.
It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetNet 2005/2005f is recommended to be powered by DC24V
(18~32V) from the 2-pin terminal block.
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
A Beijer Electronics Group Company
Package Check List
JetNet 2005/2005f Switch
Quick Installation Guide
JetNet 2005/2005f Industrial Ethernet Switch supports 5 10/100Base TX (JetNet 2005) or 4
10/100TX plus one 100FX Ethernet port (JetNet 2005f). In order to survive under harsh
environment, JetNet 2005/2005f chooses industrial-grade aluminum case with IP30 standard
protection.
It provides one relay output to alarm port break events, which is enabled/ disabled by the
dip switch. JetNet 2005/2005f is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
Installation
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
A Beijer Electronics Group Company
Port Alam Fault V+ V- DC24
Power Inputs
Fault
V-
V+
V-
Relay Output,
Carry ability
1A @24V
Fault V+
2. Connecting the Fiber Port (JetNet 2005f): Connect the ber port on your JetNet
2005f to another Fiber Ethernet device, by following the gure below. Wrong connection
will cause the ber port not working properly.
！
is is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
P1 to P5
(Pin1 ~5)
Pin No. # Status Description
To enable port break alarm at this port.ON
O To disable port break alarm at this port.
NO
1 2 543
Alarm Switch
DIP Switch Settings for Alarm Relay Output
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
workmanship for a period of ve (5) years from the date of delivery provided that the
Product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Connecting to Network
1. Connecting the Ethernet Ports: Connect one end of an Ethernet cable into the UTP
port of JetNet 2005/2005f, while the other end is connected to the attached networking
device. All UTP ports support auto MDI/MDIX function. e LNK / ACT LED will turn
Yellow for 10M Ethernet or Green for 100M Ethernet.
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
Package Check List
JetNet 2005/2005f Switch
Quick Installation Guide
Support
JetNet 2005/2005f Industrial Ethernet Switch supports 5 10/100Base TX (JetNet 2005) or 4
10/100TX plus one 100FX Ethernet port (JetNet 2005f). In order to survive under harsh
environment, JetNet 2005/2005f chooses industrial-grade aluminum case with IP30 standard
protection.
It provides one relay output to alarm port break events, which is enabled/ disabled by the
dip switch. JetNet 2005/2005f is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
Installation
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
DIP Switch Settings for Alarm Relay Output
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional stas are
ready to solve your problems at any time Korenix global service center's e-mail is
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Wiring the Relay Output
e relay output alarm contacts are in the middle of
the terminal block connector as shown in the gure.
By inserting the wires and set the DIP switch of Port
Alarm to "ON", relay output alarm will detect any
port failures, and form a short circuit. e alarm
relay output is "Normal Open".
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+
and V- contact on the terminal block connector
2. Tighten the wire-clamp screws to prevent the DC
wires from being loosened.
Notes: e recommended working voltage is DC24V
(DC18~ 32 V)
Grounding JetNet 2005/2005f Switch
ere is one grounding screw on the bottom side of
JetNet 2005/2005f. Connect the frame grounding of
switchto the grounding surface to ensure safety
andprevent noise to interfere communication.
！
is is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
导言
安装
客户服务
此产品保证完全符合欧盟2003年1月27日电气和电子设备危害物质限制委员会所提
出的限用指令2002/95/EC(ROHS禁令)及2011/65/EU(RoHS 2.0)。
Korenix
售后服务
KoreCARE 是科洛理思科技全球服务中心，我们专业的技术人员随时准备解答您的
疑问。科洛理思全球服务中心 EMAIL: [email protected]
详细说明及文件请至网站下载: http://www.korenix.com.cn/support_downloads.htm
业务服务: [email protected]
官网: www.korenix.com.cn
5
年质保
所有科洛理思产品的设计、制造及测试都是采用较高的工业标准。科洛理思保证
自产品出货日起提供最高5年之免费保修服务，保修期间如因零件损坏或制程不良
而导致产品故障，我们将提供免费维修服务。
然而，自然外力(火、水、雷灾)所造成的产品故障，或其它外部因素如电源干扰、
不当电源输入、不当接线等造成的损坏，不列入产品保固范围；此外，产品被误
用、未经授权的修理及修改等行为将造成保固条款失效。
注意! 请勿于电源开启时插拔接线端子，以避免产生火花造成系统损坏。
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Utility Model: M 339841
Utility Model: M 339840
JetNet 2005/2005f 工业级以太网交换机，提供5个10/100Base TX (JetNet 2005)，或
者4个10/100Base TX加1个100FX界面(JetNet 2005f)。
JetNet 2005/2005f 密闭的铝制外壳符合IP30工业防护标准。它还提供端口断线继电
器报警输出功能，透过底部的DIP拨码开关，启动或关闭报警系统。
JetNet 2005/2005f 建议供电范围︰透过 2-pin terminal block 为设备供给 DC24V
(18~32V)。
安装
导轨安装: 将JetNet 2005/2005f 后面的导轨夹
卡上导轨。
JetNet 2005/2005f
地线连接
在JetNet 2005/2005f 底部有一个地线连接螺丝。
将JetNet 2005/2005f 地线螺丝接地，可以确保设
备使用安全，并可防干扰。设备未接地，因自
然因素造成损害，将不予以修复。
电源线连接
1. 将电源线正负极插入产品底部接线端子的
V+ 和V- 接脚。
2. 将线夹拧紧，防止DC电源线脱落。备注: 建
议供电范围DC24V (DC18~32 V)
继电器报警连接
继电器输出触点在产品底部接线端子的中间，
如右图所示。使用该界面连接报警系统，并将
DIP拨码开关置"ON"，继电器报警输出系统就
可以监视任意端口的断线情况，一旦发现断线
，自动形成一个闭合环路。正常情况下报警系
统是开路。
网络连接
1. 连接以太口: 双绞线的一端连接JetNet 2005/2005f UTP口，另一段连接网络设备
。所有UTP口自适应MDI/MDIX10M连接时LNK / ACT指示灯显示黄色，100M
连接时指示灯显示绿色。
2. 连接光口(JetNet 2005f): 光纤线一端连接JetNet 2005f光口，另一端连设备，如下
图所示连接模式。错误的连接会致使光口不能正常工作。
Fault V-V+
继电器报警输出
Carry ability 1A @24V
电源输入
Fault
V-V+
Tel:+886-2-89111000
Fax:+886-2-29123328
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000N2005002
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
状态 描述
启动该端口断线报警
关闭该端口断线报警
DIP
拨码开关设置继电器报警
NO
1 2 543
Alarm Switch
P1 to P5
(Pin1 ~5)
Pin No. #
ON
O
产品清单
JetNet 2005/2005f 工业级以太网交换机
快速安装手册
Port Alam Fault V+ V- DC24
A Beijer Electronics Group Company
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
Package Check List
Unpack the box, you will find
JetNet 2005/2005f Switch
Quick Installation Guide
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
Overview
JetNet 2005/2005f Industrial Ethernet Switch, conforming IEEE 802.3 and 802.3u
standard, supports 5 10/100Base TX (JetNet 2005) or 4 10/100TX plus one
100FX Ethernet port (JetNet 2005f). JetNet 2005/2005f adopts slim industrial
design to save rail space of compact system requirement. In order to survive
under harsh environment, JetNet 2005/2005f chooses industrial-grade aluminum
case with IP30 standard protection.
It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetNet 2005/2005f is recommended to be powered by DC24V
(18~32V) from the 2-pin terminal block.
JetNet 2005/2005f Industrial Ethernet Switch
Quick Installation Guide V1.2
A Beijer Electronics Group Company
Package Check List
JetNet 2005/2005f Switch
Quick Installation Guide
JetNet 2005/2005f Industrial Ethernet Switch supports 5 10/100Base TX (JetNet 2005) or 4
10/100TX plus one 100FX Ethernet port (JetNet 2005f). In order to survive under harsh
environment, JetNet 2005/2005f chooses industrial-grade aluminum case with IP30 standard
protection.
It provides one relay output to alarm port break events, which is enabled/ disabled by the
dip switch. JetNet 2005/2005f is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Overview
Installation
Mounting the Unit
Din-Rail mount: Mount the din-rail clip screwed on the rear
of JetNet 2005/2005f on the DIN rail.
-
1
-
2
Korenix JetNet 2005f Quick Installation Manual
- カテゴリー
- ネットワークスイッチ
- タイプ
- Quick Installation Manual
他の言語で
- English: Korenix JetNet 2005f
関連論文
-
Korenix JetNet3008G V2 Quick Installation Manual
-
-
-
-
-
-
-
-
-
