Korenix JetCon 2302 Quick Installation Manual

ブランド: Korenix

モデル: JetCon 2302

カテゴリー: ネットワークスイッチ

タイプ: Quick Installation Manual

5 Years Warranty

Each of Korenix’s product line is designed, produced, and tested with high industrial

standard. Korenix warrants that the Product(s) shall be free from defects in materials and

Support

workmanship for a period of ve (5) years from the date of delivery provided that the

Product was properly installed and used.

is warranty is voided if defects, malfunctions or failures of the warranted Product are

caused by damage resulting from force measure (such as oods, re, etc.), other external

forces such as power disturbances, over spec power input, or incorrect cabling; or the

warranted Product is misused, abused, or operated, altered and repaired in an unauthorized

or improper way.

Attention! To avoid system damage caused by sparks, please DO NOT plug in power

connector when power is on.

e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European

Parliament and of the Council of 27 January 2003 on the restriction of the use of certain

hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)

Korenix Customer Service

KoreCARE is Korenix Technology's global service center, where our professional stas are

ready to solve your problems at any time Korenix global service center's e-mail is

[email protected].

For more information and documents download please visit our website:

http://www.korenix.com/downloads.htm

Installation

Mount the unit

Din-Rail mount: Mount the din-rail clip on the rear of JetCon 2302 on

the DIN rail. For information about the DIN Rail installation, please

refer to user’s manual.

Wiring the Power Inputs

1. Insert the positive and negative wires into the V+ and V- contact on the terminal block

connector.

2. Tighten the wire-clamp screws to prevent the DC wires from being loosened.

3. Both of the redundant power inputs accept negative or positive type power source; the

negative power source is commonly used in telecom applications. See the gure-1 and gure-2

for the power wiring.

Note: e recommended working voltage is DC24V (DC10~ 60V); both power inputs

should apply with the same power system; either positive or negative.

Wiring the Relay Output and Chassis Grounding

e relay output alarm contacts are in the middle of the terminal block connector as shown in

the gure below.

By inserting the wires and setting the DIP switch of the respective Port Alarm to “ON”, relay

output alarm will detect any port failure and form a short circuit. e alarm relay output is

“Normal Open”. Please refer to Figure -3 for the relay wiring architecture.

Operating Mode Selection

e JetCon 2302 is not only a 4-port Switch, but it is also a 2-channel Fast Ethernet Media

Converter. It is congured by the DIP switch and activated through the power resetting or the

reset button. To understand the functions of the Switching and converter modes, refer to the

table below:

In an industrial environment there might be

a lot of devices that generate electromagnetic

noise, such as AC motors, electric welding

machines and power generators. ese

devices will generate electric noise or surges

that might disturb communication. To

prevent these interferences, the JetCon 2302

should be well earthed.

Connecting to Network

1. Connecting the Ethernet Port: Connect the Ethernet RJ-45 port to another networking

device by properly twisted cable (UTP or STP). If the port is well linked with partner, the

Link LED (Green) will turn on and the Activity LED will start blinking slowly when the

packets are transmitting and receiving. e RJ-45 ports support MDI/MDI-X function.

2. Connecting the Fiber Port: Connect the ber port to ber link partner by proper ber

cable as shown in the Figure-4. Ensure that both of connected ber ports are the same type

and use exactly optical ber cable.

！

is is a Class 1 Laser/LED product.

Don't look into the Laser/LED Beam.

ATTENTION

Cable Wiring(SC to SC)

RX A TX B

TX A RX B

DIP Switch Setting

Package Check List



JetCon 2302 Industrial Media Converter



Quick Installation Guide

JetCon 2302 Industrial Fast Ethernet to Fiber Media Converter

Quick Installation Guide V1.3

JetCon 2302 is a Fast Ethernet to Fiber Media Converter with 2 Fast Ethernet copper and 2

ber ports allowing the device to act as 4 port Fast Ethernet Fiber switch or 2-channel

Converter for exible industrial applications. In switch mode, JetCon 2302 is an industrial

4-port 10/100Mbps Fast Ethernet Switch, incorporating 3.2Gbps switching fabric with

non-blocking store and forward technology to fulll the high transmission performance

requirements. In converter mode, JetCon 2302 is a cost eective industrial 2-channel

10/100TX to 100FX media converter with an error packet ltering function. It also provides

relay alarm output function for the port and power alert. e heavy industrial EMC compliant

JetCon 2302, designed with IP31 grade enclosure, is equipped with dual redundant

DC10~60V power inputs and provides 1.5KV Hi-Pot isolation protection and wide operating

temperature, therefore ensuring highly reliable network performance under harsh industrial

environments with vibration and shock.

Overview

A Beijer Electronics Group Company

Figure -3

Converter mode

No.

Port 1, 3 grouped as a single channel A

Port 2, 4 grouped as a single channel B

Store and forward

Fully supported

Switching mode

Yes

Store and forward

Fully supported

Data exchange

Forward Technology

Port Event Alarm

Description

Port link down event alarm enabled.

Port link down event alarm disabled. (Default)

Enabled Converter mode

Switch mode. (Default)

Enabled power event alarm

Disabled power event alarm (Default)

Status

Off

Not avaliable

Pin No. #

DIP 1~4

DIP 5

DIP 6

DIP 7

DIP Switch Setting

Description

Green on: the port is linked well with partner

Green blinking: the port is transmitting packet.

Green on: the port is linked well with partner.

Green blinking: the port is transmitting packet.

Green on: the power is on applying.

Red on: port link down or power off event occurred, and the

alarm relay output conductors formed a short circuit.

Green on: the device is setting on the converter mode.

LED color

Green

Yellow

Green

Yellow

Green

Red

Green

Indicators

Ethernet

RJ-45

Fiber

PWR 1,2

Con.

Alm

Package Check List



JetCon 2301 Industrial Media Converter



Quick Installation Guide

A Beijer Electronics Group Company

JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter

Quick Installation Guide V1.1

JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of

forwarding modes – Store and Forward, Modied Cut-through, Pure Converter and

Converter with auto-change modes. e JetCon 2301 adopts rugged aluminum case with

IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh

environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or

-40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes

for alerting remote or central management systems when a remote fault occurs. It also

adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be

enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range

DC10~60V through the 6-pin removable terminal block. e ber port supports

Single-mode or Multi-mode for providing up to 30KM extended distance transmission.