Korenix JetCon 2301 Quick Installation Manual

ブランド: Korenix

モデル: JetCon 2301

カテゴリー: ネットワークスイッチ

タイプ: Quick Installation Manual

5 Years Warranty

Each of Korenix’s product line is designed, produced, and tested with high industrial

standard. Korenix warrants that the Product(s) shall be free from defects in materials and

Support

Note: After adjusting the DIP-switch, please reboot the unit to activate

the new settings.

Support

workmanship for a period of ve (5) years from the date of delivery provided that the

Product was properly installed and used.

is warranty is voided if defects, malfunctions or failures of the warranted Product are

caused by damage resulting from force measure (such as oods, re, etc.), other external

forces such as power disturbances, over spec power input, or incorrect cabling; or the

warranted Product is misused, abused, or operated, altered and repaired in an unauthorized

or improper way.

Attention! To avoid system damage caused by sparks, please DO NOT plug in power

connector when power is on.

e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European

Parliament and of the Council of 27 January 2003 on the restriction of the use of certain

hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)

Korenix Customer Service

KoreCARE is Korenix Technology's global service center, where our professional stas are

ready to solve your problems at any time Korenix global service center's e-mail is

[email protected].

For more information and documents download please visit our website:

http://www.korenix.com/downloads.htm

Package Check List



JetCon 2301 Industrial Media Converter



Quick Installation Guide

JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter

Quick Installation Guide V1.1

JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of

forwarding modes – Store and Forward, Modied Cut-through, Pure Converter and

Converter with auto-change modes. e JetCon 2301 adopts rugged aluminum case with

IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh environments

with severe electromagnetic interference and -25~70°C (JetCon 2301) or -40~75°C (JetCon

2301-w). It features Link Loss Forwarding to forward link status changes for alerting remote

or central management systems when a remote fault occurs. It also adopts one relay output to

alarm users if a port link fails or if the power fails. Alarms can be enabled/ disabled by dip

switch. JetCon 2301 has redundant power inputs with wide range DC10~60V through the

6-pin removable terminal block. e ber port supports Single-mode or Multi-mode for

providing up to 30KM extended distance transmission.

Overview

A Beijer Electronics Group Company

Installation

Mount the unit

Din-Rail mount: Mount the din-rail clip on the rear of JetCon 2301 on

the DIN rail. For information about the DIN Rail installation, please

refer to user’s manual.

Grounding JetCon 2301

ere is one grounding screw on the bottom side

of JetCon 2301. Connect the frame grounding of

JetCon 2301 to the grounding surface to ensure

safety and prevent noise for communication

interference.

Wiring the Power Inputs

1. Insert the positive and negative

wires into the V+ and V- contact on

the terminal block connector.

2. Tighten the wire-clamp screws to

prevent the power wires from being

loosened.

Note: e recommended working voltage

is DC 24V (Input range: DC10~ 60 V)

Wiring the Relay Output

e relay output contacts are in the middle of the

terminal block connector as shown in gure

below. By inserting the wires and by setting the

DIP switch of the respective alarm function to

“ON”, relay output alarm will detect port or

power fault, and form a short circuit. e alarm

relay output is “Normal Open”. For detailed

information, please refer to chapter 2-5 of the

User’s Manual.

Note: e relay contact supports only 1A current, DC 24V. It is not recommended

to apply higher voltage and current higher than this specication.

Connecting to Network

1. Connecting the Ethernet Port: Connect one end of an Ethernet cable into the UTP port

of JetCon 2301, while the other end is connected to the attached networking device. UTP

port supports auto MDI/MDIX function. e LNK / ACT LED will turn on and start

ashing to indicate RJ-45 port links and the packets received and transmitted from RJ-45.

2. Connecting the Fiber Port: Connect the ber port of your JetCon 2301 to another Fiber

Ethernet device, by following the gure below. Wrong connection or wrong ber cable type

will cause the ber port not working properly.

3. For dierent link distances, the JetCon 2301 provides JetCon 2301-m” for multi-mode

ber and “JetCon 2301-s” for single-mode ber.

4. e table below illustrates ber transceiver specication.

！

is is a Class 1 Laser/LED product.

Don't look into the Laser/LED Beam.

ATTENTION

Cable Wiring(SC to SC)

RX A TX B

TX A RX B

A Beijer Electronics Group Company

JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter

Quick Installation Guide V1.1

JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of

forwarding modes – Store and Forward, Modied Cut-through, Pure Converter and

Converter with auto-change modes. e JetCon 2301 adopts rugged aluminum case with

IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh

environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or

-40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes

for alerting remote or central management systems when a remote fault occurs. It also

adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be

enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range

DC10~60V through the 6-pin removable terminal block. e ber port supports

Single-mode or Multi-mode for providing up to 30KM extended distance transmission.