TTA Utensil Stand
CK-305
Instruction Manual : Ver 1.00
●Materials : Main unit/ Stainless steel, Bracket/ Polypropylene
●Size : diameter 67×110(h)mm / 2.6"×4.3"(h)
●Weight : 160g / 0.35 lbs
● Maximum loading weight : 1kg / 2.2 lbs
Specifications
Contents (Name of the Parts)
Thank you for purchasing a Snow Peak product. This product is Utensil Stand, part of Snow Peak’s Tabletop Architect series. For safety, read the following instruction manual before use. Please keep it safe for
future reference. Finally, if you find anything that you do not understand in the description or any problems with the product, please stop use immediately and contact the retailer or Snow Peak Customer Service.
Safety Precautions: Before use, please read thoroughly to ensure safety and avoid accidents.
DANGER / Misuse could easily result in a serious accident or death.
● Keep an eye on small children when they are nearby. Children playing with the product may cause unexpected accidents.
WARNING / Misuse could result in serious injury or death.
●Before using the product, check each part for abnormalities. If there are abnormalities, take the product to the dealer or Snow Peak
Customer Service for inspection or repair.
●Do not use this product near heat sources such as stoves or barbecue boxes. The unit may become hot, potentially resulting in burns or
ignition of stored items.
●Do not put this product on fire. Using over flames may cause burns or damage to the unit.
●When using in combination with the Tabletop Architect series, be sure to read the instruction manual of each product carefully.
●This product can hold a maximum weight of 1 kg (2.2lbs). When used in combination with the Tabletop series, the maximum weight of the
other products must be observed.
CAUTION / Misuse could result in injury to the user and/or damage to property.
●Use in combination with products other than the Tabletop series or products of other manufacturers may result in injury or damage to the
product due to instability.
●This product cannot be used as a drinking vessel. Due to the structure of this product, if more than a certain amount of water is added,
liquid will leak from the hole in the center of the main unit and cause damage to the product.
●If using this product as a flower vase, fill it with about halfway with water. Overfilling the product may cause leaks.
●After assembling this product, check for any wobbling of the main unit, as well as looseness in the clamps and other extension pieces.
Periodically check each screw for looseness during use, tightening as needed. Using the product with wobbling or loose screws may
cause parts to disconnect or objects to fall, resulting in injury or damage to the product.
●Be careful if the product is exposed to direct sunlight for long periods of time, as it will become hot.
●When using the product outdoors, use it under a tarp or in a location where it will not be exposed to rainwater. Leaving the product wet
for an extended periods will cause rust to form on the screws and joints, resulting in discoloration and poor functionality.
●Be sure to remove any items placed inside before adjusting and moving the mounting position or putting the product away.
●Do not subject the product to strong impacts. Dropping or rough handling may deform or damage the product.
Instructions for Use
Snow Peak, Inc.
456, Nakanohara, Sanjo-Shi, Niigata 955-0147 Japan
Tel. +81 256-46-5858 / Fax. +81 256-46-5860
www.snowpeak.co.jp
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. [email protected] / www.snowpeak.com
Maintenance
●Before use, wash the product with the soft side of a sponge dipped in neutral detergent. Using a scrubber or the rough side of a sponge may cause scratches.
●After use, wash the product with a neutral detergent, remove water with a soft cloth such as a towel, and dry it in a shaded and well-ventilated place. Dirt and moisture left on the surface may cause rust.
●Do not use a dishwasher or dryer for this product.
This product is designed to be assembled with a shaft of 8 mm in diameter, such as the 300 mm shaft which is included in CK-302 TTA Lantern Hanger and CK-303 TTA Unit Frame. This product cannot be
combined with products other than the Tabletop Architect series or products from other manufacturers. Be sure to read and understand the instruction manuals of complementary products before assembling.
This manual explains an example of installation on a 300 mm shaft attached to a CK-300 TTA Clamp.
※Cautionary points for assembly
This product cannot be installed on the groove at the end of the 300
mm shaft due to the risk of tipping over. When installing on a 300 mm
shaft, install on the third groove, counting from the bottom.
Before installing this product, check the clamps and shafts are
securely tightened and not loose.
Attach the bracket to the groove on the 300 mm shaft. Align the
protruding part of the bracket with the groove on the 300 mm shaft
as shown in the illustration, then close and secure the bracket.
Put the main unit through the 300 mm shaft and secure it. Push the
main unit into the bracket until it is secured.
Follow the reverse procedure to disassemble.
●If professional repairs are required, please contact the retailer where you purchased the product or Snow Peak Customer Service.
●When you request repairs, please make sure that the product is dry and clean.
●Please attach a memo or a tag indicating the necessary repair and please write details of how and when the damage occurred.
●Transportation and repair costs are determined as follows.
1. Within warranty: The transportation cost (both ways) and repair cost will be covered by Snow Peak.
2.Outside warranty: The transportation cost (both ways) and repair cost will be covered by the customer.
Repair
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find any product defects, please contact the retailer where you purchased the product or Snow Peak
Customer Service. If there are apparent defects in the product's manufacturing, the defective product will be repaired or exchanged free of charge. In other cases, Snow Peak will repair the product for an
appropriate fee. The decision to repair or replace the product will be at our discretion. Snow Peak will not repair the product for any damage that occurred due to the following:
1.Material deterioration caused by age
2.Damage caused by modifications or rough handling
3.Damage caused by inappropriate use not mentioned in the instruction manual
4.Damage caused by unexpected accidents
5.Any damage other than defects in the manufacturing process
Warranty
6.Damage caused by dust or rust
7.Damage and defects caused by dismantling the product
8.Damage and defects caused by dropping, jolting or other shocks
9. Deterioration or failure of parts due to friction
10. Damage caused by the use of the product in combination with another manufacturer's products
Instruction manual
(This manual)
Bracket
Main unit
300mm Shaft (Sold separately)
CK-300 TTA clamp (Sold separately)
Cannot be
installed on tip
groove.
Can be installed
on the third row
from the bottom.
300mm shaft groove
Bracket protrusions
/
