A
D
B
C
b
2
1
a
4
3
5
6
(1)
(2)
(2)
(3)
(4)
(4)
©
AT-75_l_stand_j1(B4) 1 ページ ２００８年８月６日 水曜日 午後４時１４分
(1)
(2)
(3)
(3)
(5)
(4)
(1)
*5100000712- 01*
5100000712 1PD
AT-75_l_stand_j1(B4) 2 ページ ２００８年８月６日 水曜日 午後４時１４分
Setting Up the AT-75 and the AT-75’s Stand
• Make sure that another person is on hand to help with the assembly and setup.
• Be very careful when lifting and moving the AT-75, since it is quite heavy.
• Be very careful, when you assemble and move the AT-75, to make sure that you do not drop it on your hands or feet.
• To move the AT-75, lift it carefully—all the while keeping it level.
• When assembling the AT-75 stand, do not apply excessive pressure on any part. To do so can cause metal parts to get bent out of shape, and
may damage wooden parts.
• Should you remove screws, knob bolts, caps, and cord clamps, make sure to put them in a safe place out of children’s reach, so there is no
chance of them being swallowed accidentally.
●
Part Check
(1) Before you begin assembling the stand, check that all the parts were
supplied.
A: Side Board (left)
B: Side Board (right)
C: Pedal Board
D: Rear Board
1: Screw a (M6 x 70 mm) x 4
2: Screw b (M6 x 20 mm) x 4
3: Knob bolt (M5 x 20 mm) x 2
4: Cap x 4
5: Cord Clamp x 3
6: Cord Hook (with Wing Nut) x 1
(2) You will also need to have a Phillips screwdriver.
●
Stand Assembly
At first, assemble the entire stand in a temporary fashion, without
really tightening the screws. Then, after checking the overall alignment
of the boards (and gently shifting certain parts where necessary), go
around and tightly fasten each of the screws.
(1) Detach the pedal cord which are temporarily attached to the bottom of
the pedal board.
(2) Attach the side boards (so that the metal parts face inside) for the right
and left sides to the pedal board using screws “a” (two each on the left
and right).
(3) Attach the rear board with the wood grain side facing inside to the side
boards for the right and left sides using screws “b” (two each on the left
and right).
(4) Attach the caps (two each on the left and right) on screws “a.”
* Fasten each screw tightly, then place the stand in a stable and horizon-
tal place.
* Do not allow the pedal cord or power cord to get twisted or pinched
while assembling the stand.
A
D
B
C
b
2
1
a
4
3
5
6
(1)
Screw a
(2)
(2)
Pedal Cord
Screw b
Wood grain side
(3)
(4)
Cap
(4)
Cap
Copyright © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
● Installing the Organ on the Stand
(1) Align the pins (one each at right and left) on the bottom of the organ
with the receiving slots of the stand on the side board, then slide the
organ forward until the screws are held in place.
* Firmly grasp the organ at the front and back. Be careful, so you do not
get your fingers pinched.
* Be careful not to pinch the speaker cord and pedal cord, which are
located on the bottom of the organ.
(2) Fasten the organ to the stand with the knob bolt (one each on the left
and right).
(3) Connect the stand’s pedal cord to the pedal cord leading from the
organ.
You can push the plugged portion underneath the stand to keep the
pedal cord connection hidden from behind.
(4) Connect the power cord to the AC inlet on the back of the organ.
(5) Attach the music rest (supplied with the organ) to the top of the organ.
(6) If necessary, peel off the sheet from the rear of the cord clamps, and
attach the clamps to the rear edge of the (right) side board (in three
places).
●
Adjusting the Adjuster
(1) Rotate the adjuster at the bottom of the pedal board, so that the adjuster
touches the floor. If you have the AT-75 placed on a carpet, lower it until
it pushes into the carpet.
●
Attaching the Cord Hook
You can use the cord hook to fasten the cables together to keep them
out of the way of your feet. As appropriate for your situation, screw the
cord hook (with wing nut) approximately 80% of the way into the hole
located on the bottom of the organ (near the left foot), orient the hook in
the desired direction, and tighten the wing nut to fasten it.
●
When Moving the AT-75
* Be sure to detach the organ from the stand before transporting it.
Attempting to transport the organ together with the stand may damage
the connecting hardware.
(1) Rotate the adjuster at the bottom of the pedal board to leave the floor.
(2) Disconnect the power cord at the back of the organ.
(3) Disconnect the stand’s pedal cord from the organ’s pedal cord.
(4) Remove the knob bolt (one each at left and right).
(5) Push the organ slightly away from yourself to disengage the pins (one
each at left and right) located on the bottom of the organ from the
receiving slots of the stand, and take the organ off of the stand.
(6) Transport the organ and stand separately.
(7) When moving the stand, grasp it by the side boards (at the locations
shown in the illustration).
(1)
(2)
Knob Bolt
Please don’t get
your fingers pinched
(3)
(3)
(5)
(4)
Note the shape of the connectors for the pedal cord. Connect
the matching pairs of connectors, making sure they click into
place. After the cords have been connected, grasp the
connectors and gently tug on them to confirm that they’re
connected properly, and won’t easily come apart.
Organ side
Stand side
Pedal Cord
Music Rest
AC Inlet
Caution
Pedal Cord
Cord Clamp
(1)
Foot
Cord Hook
*5100000712- 01*
5100000712 1PD
-
1
-
2
-
3
-
4
