*5100002091- 01*
1.
2.
3.
A
B
C
D
F
E
G
H
A
B
C
D
E
F
G
H
4.
5.
6.
7.
8.
9.
1.
2.
3.
AC IN
AC OUT
AC IN
KSC-48
©
KSC-48 STAND ASSEMBLY
Before you begin assembling the stand, check that all the parts were supplied. You will also need to have a Phillips screwdriver.
Before using this unit, carefully read the sections entitled:
“IMPORTANT SAFETY INSTRUCTIONS,” “USING THE UNIT
SAFELY,” and “IMPORTANT NOTES” (separate sheet)
.
This manual, sparate sheet, and RK-300 owner’s manual should be
saved and kept on hand as a convenient reference.
* Fasten each screw tightly, then place the stand in a stable and horizontal place.
* Do not allow the speaker cable or power cable to get twisted or pinched while assembling the stand.
At first, assemble the entire stand in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the
boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws. When securing the screws, lay the entire
unit sideways.
1.
Attach the side board R (A) for the right sides to the speaker
box (C).
Use screws (G) to temporarily fasten these parts together.
2.
Attach the side board L (B) for the left sides to the speaker
box (C).
Use screws (G) to temporarily fasten these parts together.
3.
After you’ve temporarily fastened the screws, place the
stand upright, and securely tighten screws (G) to fasten the
speaker box and side boards.
Checking the Included Items
A
B
C
D
F
E
G
H
For details on using the cord clamps,
refer to the RK-300 Owner’s Manual.
A
Side Board R 1
B Side Board L 1
C Speaker Box 1
D Piano Pedal 1
E Dedicated Power Cord 1
F Knob Bolt 4
G Screw (M6 x 20 mm) 6
H Cord clamp 8
Assembly Procedure
Stand Assembly
4.
Detach the jack cover that is attached to the RK-300’s rear
panel.
* Keep the removed screws in a safe place so that they will not be
lost.
fig.03.e
5.
Set the RK-300 on the stand, then firmly attach the four knob
bolts (F).
* When handling the RK-300, firmly grasp it. Be careful, so you do
not get your fingers pinched.
fig.03.e
* To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power on
all devices before making any connections.
6.
Connect the speaker cable extending from the speaker box
to the SPEAKER connector located on the RK-300’s rear
panel.
7.
Connect the piano pedal (D) to the PIANO PEDAL connector
located on the RK-300’s rear panel.
8.
Connect dedicated power cord (E) between the AC OUT
located on the RK-300’s rear panel and the AC IN of the stand.
9.
Connect the power cord to the AC IN located on the RK-300’s
rear panel.
Since this product is very heavy, you must make sure that a sufficient
number of people are on hand to help, so you can lift and move it
safely, without causing strain.
1.
Disconnect the power cord.
2.
Disconnect the piano pedal.
3.
When moving the RK-300, lift it carefully, all the while
keeping it horizontal. Take care not to drop it on your feet or
pinch your hands.
Place the RK-300 onto the Stand
Connect the Speaker Cable
Loosen
Loosen
Please don’t
get your fingers
pinched
Connect the Piano Pedal
Connect the Power Cords
When Transporting the Unit
Dedicated power cord
AC IN
AC OUT
Power cord
AC IN
Make sure that another person is on hand to help with the assembly and setup.
Be very careful, when you assemble and move the stand, to make sure that you do not drop it on your hands or feet.
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Copyright © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
/