1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
3
2
1
c
b
a
4
d
D
E
A
B
C
1
2
3
4
5
6
7
9
8
10
11
KSC-22/30 40565278 2PD
STAND ASSEMBLY
Part Check
Before you begin assembling the stand, check that all the parts
were supplied. You will also need to have a Phillips screwdriver.
fig.01
A: Side Board (left) 1: Screw a (4 x 16 mm) x 2
B: Side Board (right) 2: Screw b (4 x 25 mm) x 4
C: Pedal Board 3: Screw c (M6 x 45 mm) x 4
D: Rear Board 4: Screw d (M5 x 20 mm) x 8
E: Speaker Box
Assembly Procedure
* Fasten each screw tightly, then place the stand in a stable and horizontal place.
* Do not allow the pedal cord or power cable to get twisted or pinched while
assembling the stand.
Stand Assembly
At first, assemble the entire stand in a temporary fashion, without
really tightening the screws. Then, after checking the overall
alignment of the boards (and gently shifting certain parts where
necessary), go around and tightly fasten each of the screws.
When securing the screws, lay the entire unit sideways.
1. Attach the side boards for the right and left sides to the pedal board
(so that the metal parts face inside) using screws “c” (M6 x 45 mm).
Stand the instrument back up.
2. Place the rear board as shown below, and adjust the screw holes of
the rear board and the pedal board.
3. Attach the rear board to the metal parts on the side boards from the
front using screws “a” (4 x 16 mm). For clamping the rear board,
press each upper portion of both side boards. Then, fasten it to the
pedal board from the back using screws “b” (4 x 25 mm).
4. Set the speaker box so that the speaker cable is above it, and align
the holes in the metal parts on the inner side of the side boards with
the holes in the speaker box.
fig.02.e
5. Attach the speaker box to the metal parts on the inside of the side
boards from underneath using screws “d” (M5 x 20 mm). Then fasten
the rear with screws “d” (M5 x 20 mm) as well.
fig.02.e
Installing the Piano on the Stand
6. Align the protruding screws (one each at right and left) on the bottom
of the piano with the openings in the metal fittings on the side board,
then slide the piano forward until the screws are held in place.
7. Fasten the piano to the stand with the screw “d” (M5 X 20 mm) (two
each for the right and left).
* When handling the piano, firmly grasp it at the front and back. Be careful, so you do
not get your fingers pinched.
fig.03.e
Connecting the Speaker cable, the Pedal and
Power Cords
8. Connect the speaker cable to the speaker connector.
9. Connect the pedal cord to the Pedal connector on the rear of the
piano.
10. Connect the power cord to the power inlet on the piano, then plug the
other end into a wall socket.
fig.04
Adjusting the Adjuster
11. Lower the adjuster at the bottom of the pedal board (by rotating it), so
that the adjuster touches the floor. If you have the piano placed on a
carpet, lower it until it pushes into the carpet.
fig.05.e
When Moving the Piano
Disconnect the power cord and raise the stand’s adjuster. Then lift
the piano while keeping it level, and move it with care, so that you
do not drop it on your feet, or get your hands caught.
3
2
1
c
b
a
4
d
D
E
A
B
C
1
2
3
4
Screw c
Screw c
Screw b
Screw a
5
Screw d
Screw d
6
7
Please don't get
your fingers pinched
Screw d
Screw d
9
8
10
11
Adjuster
Make sure that another person is on hand to help with the assembly and setup.
Be very careful, when you assemble and move the piano, to make sure that you do not drop it on
your hands or feet.
To move the piano, lift it carefully—all the while keeping it level.
KSC-22/30 40565278 2PD
/