1.
2.
3.
4.
5.
6.
7.
8.
D
A
B
C
3
2
1
c
b
a
4
d
1
2
3
4
5
6
7
8
KS-307D 40344923 ’00-1-A3-11K
STAND ASSEMBLY (KS-307)
Part Check
Before you begin assembling the stand, check that all the parts were
supplied. You will also need to have a Phillips screwdriver.
fig.01
A: Side Board (left) 1: Screw a (4 x 16 mm) x 2
B: Side Board (right) 2: Screw b (4 x 25 mm) x 4
C: Pedal Board 3: Screw c (M6 x 60 mm) x 4
D: Rear Board 4: Screw d (M5 x 20 mm) x 2
Assembly Procedure
* Fasten each screw tightly, then place the stand in a stable and horizontal
place.
* Do not allow the pedal cord or power cable to get twisted or pinched
while assembling the stand.
Stand Assembly
At first, assemble the entire stand in a temporary fashion, without
really tightening the screws. Then, after checking the overall
alignment of the boards (and gently shifting certain parts where
necessary), go around and tightly fasten each of the screws.
1. Attach the side boards for the right and left sides to the
pedal board (so that the metal parts face inside) using
screws “c” (M6 x 60 mm).
2. Place the rear board as shown below, with the wood grain
side facing inside, and adjust the screw holes of the rear
board and the pedal board.
3. Attach the rear board to the metal parts on the side boards
from the front using screws “a” (4 x 16 mm). For clamping
the rear board, press each upper portion of both side
boards. Then, fasten it to the pedal board from the back
using screws “b” (4 x 25 mm).
fig.02.e
Installing the Piano on the Stand
4. Align the protruding screws (one each at right and left) on
the bottom of the piano with the openings in the metal
fittings on the side board, then slide the piano forward until
the screws are held in place.
5. Fasten the piano to the stand with the screw “d” (M5 X 20
mm) (one each for the right and left).
* When handling the piano, firmly grasp it at the front and back. Be
careful, so you do not get your fingers pinched.
fig.03.e
Connecting the Pedal and Power Cords
6. Connect the pedal cord to the Pedal jack on the rear of the
piano.
7. Connect the power cord to the power inlet on the piano, then
plug the other end into a wall socket.
fig.04
Adjusting the Adjuster
8. Lower the adjuster at the bottom of the pedal board (by
rotating it), so that the adjuster touches the floor. If you have
the piano placed on a carpet, lower it until it pushes into the
carpet.
fig.05.e
When Moving the Piano
Disconnect the power cord and raise the stand’s adjuster. Then lift the
piano while keeping it level, and move it with care, so that you do not
drop it on your feet, or get your hands caught.
D
A
B
C
3
2
1
c
b
a
4
d
Screw b
Wood grain
side
Screw c
Screw a
1
2
3
4
5
Please don't get
your fingers pinched
Screw d
6
7
Adjuster
8
Make sure that another person is on hand to help with the assembly and setup.
Be very careful, when you assemble and move the piano, to make sure that you do not
drop it on your hands or feet.
To move the piano, lift it carefully—all the while keeping it level.
KS-307 40344923 ’00-1-A3-11K
/