40560823 1*PD
KS-88 Stand Assembly
• Make sure that another person is on hand to help with the assembly and setup.
• Be very careful, when you assemble and move the VK-88, to make sure that you do not drop it on your hands or feet.
• To move the VK-88, lift it carefully—all the while keeping it level.
• Assemble the KS-88 with the stand lying on its back, with the rear panel facing down.
• Should you remove knob bolt and screws for stand, make sure to put them in a safe place out of children's reach, so there is no chance of them being swallowed accidentally.
Check the Parts
Before you begin assembling the stand, check that all the parts
were supplied. You will also need to have a Phillips screwdriver.
A: Side Board (left)
B: Side Board (right)
C: Center Board
D: Center Board Lower
E: Front Board
F: Screw (M6 x 70 mm) x 8 (including two spares)
G: Screw (M4 x 16 mm) x 2
H: Knob Bolt x 2
I: Round Nuts x 8 (including two spares)
J: Cap x 2
Assembly Procedure
Stand Assembly
* Assemble the KS-88 with the stand lying on its back, with the
rear panel facing down.
(1) Insert the six round nuts (I) in the center board (C) and
lower center board (D).
Insert each of the round nuts until the cross-shaped slot in the
head is flush with the surface.
Turn each nut so that the longer slot of the cross is horizontal
(refer to figure below).
(2) Screw one of the side boards (A) to the center board (C) and
lower center board (D) using three screws (F).
If you have difficulty getting the screw in, adjust the
orientation of the round nut.
(3) Screw the other side board (B) to the center board (C) and
lower center board (D) using three screws (F).
If you have difficulty getting the screw in, adjust the
orientation of the round nut.
(4) Attach the caps (J) to the side boards (one for each side).
Pinch the tips of the caps closed while inserting the caps into
the holes in the side board.
(5) Stand the entire assembly up.
(6) After righting the stand, check for any looseness in the
screws; screw in any that are loose while the stand is in its
normal position.
(7) Attach the front board (E)with the screws (G) in two places.
Attaching the VK-88 to the Stand (KS-88)
(8) Align the screws on the bottom panel of the VK-88 with the
fittings in the side boards (left and right) of the stand (KS-
88), then pull the VK-88’s rear panel, pulling the screws into
the slots.
(9) Secure the VK-88 to the stand (KS-88) with the knob bolts
(H) (one each left and right).
* When handling the VK-88, firmly grasp it at the front and back.
Be careful, so you do not get your fingers pinched.
When Moving the VK-88
C
D
E
A
B
H
I
G
F
J
C
D
A
B
I
F
F
F
C
D
A
F
F
F
B
A
J
J
B
E
G
G
H
* Disconnect the power cord, cables, music rest, and rear
cover from the VK-88.
* Then lift the VK-88 and KS-88 while keeping it level, and
move it with care, so that you do not drop it on your feet,
or get your hands caught.
40560823 1*PD
C
D
E
A
B
H
I
G
F
J
C
D
A
B
I
F
F
F
C
D
A
F
F
F
B
A
J
J
B
E
G
G
H
-
1
-
2
