M18 FIW12
M18 FIWF38
User Manual
사용시 주의사항
คําสั่งเดิม
2
3
4
8
9
12
10
START
STOP
12
M18 FIW12 M18 FIWF38
5
13
14
6
Remove the battery pack before starting any work on the machine.
在机器上进行任何修护工作之前，先拿出蓄电池。
기기를 사용하지 않을때는 배터리를 빼어두십시요.
Keluarkan pek bateri sebelum memulakan sebarang kerja pada mesin.
6
1
2
2
1
click
Remove the battery pack before
starting any work on the machine.
在机器上进行任何修护工作之
前，先拿出蓄电池。
기기를 사용하지 않을때는
배터리를 빼어두십시요.
Keluarkan pek bateri sebelum
memulakan sebarang kerja
pada mesin.
7
78-100 %
55-77 %
33-54 %
10-32 %
< 10 %
8
click
M18 FIW12
click
9
M18 FIWF38
10
START
STOP
11
0-1700 0-2000 0-2500 2000
0-2400 0-2600 0-3100
0-900 0-1600 0-2500 1600
0-1900 0-2300 0-3100 0-2300
min
-1
min
-1
M18 FIW12
M18 FIWF38
0-2600
12
LOCK
13
LOCK
14
1
2
LOCK!
15
16
English
16
TECHNICAL DATA M18 FIW12
TECHNICAL DATA M18 FIW12
M18 FIWF38
M18 FIWF38
Tool reception 1/2”(13 mm) 3/8” (10 mm)
No-load speed 0-2500 min-
1
0-2500 min-
1
Impact range 0-3100 min-
1
0-3100 min-
1
Torque min. 263 ft-lbs 250 ft-lbs
Max. diameter bolt/nut
≥ M12 (12.9)/ ≥ M14 (8.8) ≥ M12 (12.9)/ ≥ M10 (8.8)
Max. diameter bolt/nut
≥ M14 (12.9)/ ≥ M16 (8.8) ≥ M12 (12.9)/ ≥ M12 (8.8)
Max. diameter bolt/nut
≥ M16 (12.9)/ ≥ M18 (8.8) ≥ M16 (12.9)/ ≥ M18 (8.8)
Max. diameter bolt/nut
≥ M12 (12.9)/ ≥ M12 (8.8)
Battery voltage 18 V 18 V
Weight according to EPTA-Procedure
01/2003 (4.0Ah/5.0 Ah)
1,8 kg 1,8 kg
Noise/vibration information
Measured values determined
according to EN 60745.
Typically, the A-weighted noise
levels of the tool are:
Sound pressure level (K = 3 dB(A))
93,5 dB (A)
93,5 dB (A
Sound power level (K = 3 dB(A))
104,5 dB (A)
104,5 dB (A)
Wear ear protectors!
Total vibration values (vector sum
in the three axes) determined
according to EN 60745.
Vibration emission value a
h
7,7
m/s
2
6,7 m/s
2
Uncertainty K
1,5
m/s
2
1,5 m/s
2
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent
applications, with di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running but not actually doing the job. This may
signi cantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Hold power tool by insulated gripping surfaces, when performing an operation
where the fastener may contact hidden wiring. Fasteners contacting a “live“ wire may
make exposed metal parts of the power tool “live“ and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.
≥ M14 (12.9)/ ≥ M16 (8.8)
17
English
17
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine.
The use of protective clothing is recommended, such as dust mask, protective gloves,
sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust.
Wear a suitable dust protection mask.
Do not use the product on any material that presents a danger to health (e.g. asbestos).
Switch the device o immediately if the insertion tool stalls! Do not switch the device on
again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled and rectify this, paying heed
to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running. The insertion tool may become hot
during use.
• when changing tools
• when setting the device down
Sawdust and splinters must not be removed while the machine is running.
When working in walls ceiling, or oor, take care to avoid electric cables and gas or water
pipes.
Secure your workpiece with a clamping device. Unclamped workpieces can cause severe
injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them.
Milwaukee Distributors o er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M18 chargers for charging System M18 battery packs. Do not use battery
packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all
times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it o immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and loosen nuts and bolts wherever no
mains connection is available.
Do not use this product in any way other than stated for normal use.
RPM SETTING
The function is designed to give the user greater control in application and reduce
damage to the fastener or work surface by automatically shutting the tool off after the tool
senses the mechanism impacting for approximately one second.
M18 FIWF38: Max RPM 1600 min-1- tool will shut off after about one second of impacting.
BATTERIES
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid
extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully charged.
To obtain the longest possible battery life remove the battery pack from the charger once
it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture.
Store the battery packs in a 30% - 50% charged condition.
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause high
current draw, the tool will vibrate for about 2 seconds and then the tool will turn OFF. To
reset, release the trigger.
Under extreme circumstances, the internal temperature of the battery could become too
high. If this happens, the battery will shut down. Place the battery on the charger to charge
and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and
international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous
Goods regulations. Transport preparation and transport are exclusively to be carried out
by appropriately trained persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts. Should components need to
be replaced which have not been described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No. as well
as the machine type printed on the label and order the drawing at your local service agents.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the product.
Please read the instructions carefully before starting the
machine.
Do not dispose of electric tools together with household
waste material. Electric tools and electronic equipment
that have reached the end of their life must be collected
separately and returned to an environmentally compatible
recycling facility. Check with your local authority or retailer
for recycling advice and collection point.
18
繁體中文
技術參數
技術參數
M18 FIW12
M18 FIW12
M18 FIWF38
M18 FIWF38
工具收納
1/2”(13 mm) 3/8” (10 mm)
空載轉速
0-2500 min-
1
0-2500 min-
1
衝擊範圍
0-3100 min-
1
0-3100 min-
1
最小扭力
263 ft-lbs 250 ft-lbs
螺絲/母最大直徑
≥ M12 (12.9)/ ≥ M14 (8.8) ≥ M12 (12.9)/ ≥ M10 (8.8)
螺絲/母最大直徑
≥ M14 (12.9)/ ≥ M16 (8.8) ≥ M12 (12.9)/ ≥ M12 (8.8)
螺絲/母最大直徑
≥ M16 (12.9)/ ≥ M18 (8.8) ≥ M16 (12.9)/ ≥ M18 (8.8)
螺絲/母最大直徑
≥ M12 (12.9)/ ≥ M12 (8.8)
電池電壓
18 V 18 V
根據EPTA-Procedure
01/2003(4.0 Ah/5.0 Ah)
的重量
1,8 kg 1,8 kg
噪音/震動資訊
依 EN 60745 所測的測
量值
一般來說，本工具的A
加權躁音標準為:
聲壓量測(K = 3 dB(A))
93,5 dB (A)
93,5 dB (A
聲壓率級(K = 3 dB(A))
104,5 dB (A)
104,5 dB (A)
穿戴護耳裝置！
依EN 60745所測的振動
總值 (三軸向量總和)
震動釋放值 a
h
7,7
m/s
2
6,7 m/s
2
不確定性 K=
1,5 m/s
2
1,5 m/s
2
警告!
本說明書所提供的震動等級是依EN 60745 規定的標準化測試所測得，且可能用於與另一個工具進行比較。該等級可用來初步評估風險。
宣告的震動釋放等級代表的是本工具的主要應用。然而，如果用於不同的應用、使用不同的配件或保養不當，震動釋放也可能不同。這可能
會在總工作時間上顯著增加風險等級。
評估震動暴露的等級還應考慮本工具關機時的時間，或當工具運轉但卻未實際使用的時間。這可能會明顯降低總工作期間的風險等級。
請確認額外的安全措施，以保護操作員不受震動的影響，例如:保養本工具與配件、保持手部溫暖和井然有序的工作方式。
警告!
請詳閱所有安全警告及說明，包括隨附於手冊內的安全警告及說
明。若未能遵守警告與指示，可能會導致觸電、火災和/或嚴重受
傷。 請將所有警告與指示存檔以供未來參考。
安全說明
應握住電動工具的絕緣握持面上，因為作業時其緊固件可能會
觸及隱藏線路。碰到「帶電」電線的緊固件會使該電動工具外
露的金屬件同樣「帶電」，從而造成作業人員觸電。
穿戴護耳裝置!暴露於噪音下可能會造成聽力損害。
≥ M14 (12.9)/ ≥ M16 (8.8)
19
19
繁體中文
其他安全和工作指示
操作機器時務必佩戴護目鏡。建議穿戴工作手套、堅固防滑的
鞋具和工作圍裙。
工具操作中引起的粉塵可能有害健康。切勿吸入粉塵。使用吸
塵裝置和配戴合適的防塵面罩。徹底清除堆積的粉塵，像是利
用真空吸塵器。
如果插入工具停滯不前, 請立即關閉設備！
當插入工具停滯不前, 請不要再次打開設備，以免引發突然反
衝力。
確定為什麼插入工具停滯不前並解決暇問題，請留意安全說
明。
可能的原因是：
- 它在待加工的工作部件中傾斜
- 它刺穿過待加工的材料
- 電動工具超載
不要將手伸入運行中的機器。插入工具在使用過程中，可能會
變熱。
警告！
燙傷危險
- 當更換工具時
- 當設置設備時
在機器運行時, 不可移除芯片和碎片。
在對天花板、地板進行作業時，請注意避開電線、瓦斯或自來
水管路。
將工件固定在穩定的平台上。妥善支撐工件能將意外傷害、鋸
片卡住或失控的風險最小化。
在機器上做任何調整前，請先取出電池組。
勿將用過的電池組與家庭廢棄物混合或燃燒電池。Milwaukee
經銷商提供舊電池回收，以保護我們的環境。
勿將電池匣與其他金屬物品一起存放（可能引起短路)。
千萬不可將金屬物件插入充電器的電池部分（導電的風險）。
僅可使用系統 System M18 充電器對系統 System M18 電池組
進行充電。請勿使用其他系統的電池組。
不可拆開蓄電池和充電器。蓄電池和充電器必須儲藏在乾燥的
空間，勿讓濕氣滲入。
在極端負載或極端溫度下，損壞的電池可能漏出內部酸液。若
碰觸到電池酸液，請即刻用肥皂與清水洗去。
若酸液接觸到眼睛，以清水沖洗至少10分鐘後立即就醫。
在機器上做任何調整前，請先取出電池組。
指定的使用條件
無電源可連接的情況下，可用無線衝擊板手來鎖緊和鬆開螺栓
和螺帽。
請勿以非正常使用的任何其他方式使用本產品。
轉速設置
該功能的目的是讓用戶應用時能夠更好地控制及當該工具
感測到機制受影響約一秒鐘後，通過自動關掉工具，從而減低
對緊固件或工作表面的損害。
M18 FIWF38：最高轉速1600 min-1──當約受影響一秒鐘後，
工具將會關掉。
維修
久未使用的電池組必須重新充電後再使用。
超過 50°C (122°F) 的高溫會降低電池組的效能。避免暴露
於高溫或陽光下(可能導致過熱)。
充電器和電池組的接點處應保持清潔。
為確保最佳電池使用壽命，電池組使用後，應再完全充電。
為確保電池的最長壽命，充電完成後，勿將電池匣繼續留在充
電器上。
電池組存放超過30天:
將電池組存放於溫度低於27°C的環境，且避免受潮。
將電池組保持在充電量30%-50%的狀態。
存放中的電池組應每六個月照常充電一次。
電池組保護
在極高扭矩、咬合、 停轉與短路的情況下會造成高電流，此時
工具會震動約兩個秒鐘，然後關閉運作。
欲重新啟動，鬆開板機。
在極端的狀況下，電池的內部溫度可能過高。如果發生這個情
形，能源表會開始閃燈直到電池匣冷卻為止。燈熄後應可以繼
續運作。
將電池放在充電器上進行充電與重設。
鋰電池運輸中
鋰離子電池須受制於危險品法例的要求。
運送鋰電池必須在符合當地、國家及國際標準及法例的情況下
進行。
使用者可於陸地上運送電池而無須受限。
第三方負責的商業式鋰電池運送須受制於危險品法例。運送的
預備及過程必須由受嚴格訓練的人士進行，亦必須得到專家在
場監管。
運送電池時：
請確保電池接觸終端受到嚴密保護及經過絕緣，防止短
路。
請確保電池組妥善包裝，防止碰撞磨刷。
切勿運送有裂痕或洩漏中的電池。
與速遞公司緊密聯繫以獲得進一步資訊。
維修
議使用Milwaukee的配件和零件。缺少檢修說明的機件如果損
壞了，必須交給Milwaukee的顧客服務中心更換。
如果需要機器的分解圖，可以向您的顧客服務中心查詢。索件
時必須提供以下資料﹕機型和機器銘牌上的六位數號碼。
符號
警告!
在機器上做任何調整前，請先取出電池組。
啟動機器前，務必詳閱說明書。
電動工具必須與生活垃圾分開處理。電動工具和已不
能使用的電子設備必須分開收集，並且把它帶到環保
回收機構。有關回收的建議和收集點，請諮詢你的地
方當局或零售商。.
20
20
简体中文
技术数据 M18 FIW12
技术数据 M18 FIW12
M18 FIWF38
M18 FIWF38
工具夹头
1/2” (13 mm) 3/8” (10 mm)
无负载转速
0-2500 min-
1
0-2500 min-
1
撞击次数
0-3100 min-
1
0-3100 min-
1
最小扭力
263 ft-lbs 250 ft-lbs
最大螺丝尺寸 /
螺母尺寸
≥ M12 (12.9)/ ≥ M14 (8.8) ≥ M12 (12.9)/ ≥ M10 (8.8)
最大螺丝尺寸 /
螺母尺寸
≥ M14 (12.9)/ ≥ M16 (8.8) ≥ M12 (12.9)/ ≥ M12 (8.8)
最大螺丝尺寸 /
螺母尺寸
≥ M16 (12.9)/ ≥ M18 (8.8) ≥ M16 (12.9)/ ≥ M18 (8.8)
最大螺丝尺寸 /
螺母尺寸
≥ M12 (12.9)/ ≥ M12 (8.8)
蓄电池电压
18 V 18 V
重量符合EPTA－
Procedure01／2003 (4,0 Ah /
5,0 Ah)
1,8 kg 1,8 kg
噪音/振动信息
本测量值符合 EN 60 745
条文的规定。
本机器的音压值通常为
音压值(K=-不可靠性
=3dB(A))
93,5 dB (A)
93,5 dB (A
音量值(K=-不可靠性
=3dB(A))
10
4,5
dB (A)
104,5 dB (A)
请戴上护耳罩！
依欧盟EN 60745 标准确
定的振荡总值（三方向
矢量和）。
振荡发射值 a
h
7,7
m/s
2
6,7 m/s
2
K-不可靠性
1,5 m/s
2
1,5 m/s
2
注意!
本规程列出的依欧盟EN 60745 标准一项标准测量方法测量的振荡级也可用于电动工具比较并适合于临时振荡负荷估计。
该振荡级代表电动工具的主要应用。电动工具的其他应用，不正确的工作工具或欠缺维护可造成振荡级偏差。此可明确提高总工
作期间的振荡负荷。
正确地估计一定工作期间的振荡负荷也要考虑到工具关闭或接通而不使用的期间。此可明确减少总工作期间的振荡负荷。
为提高操作人员对振荡作用的保护得规定补充安全措施：电动工具及工作工具的维护，温手，工作过程组织等。
警告！务必阅读所有安全提示和指示。如未确实 遵循警告
提示和指示，可能导致电击、火灾並且/ 或其他的严重伤害。
妥善保存所有的警告提示和指示，以便日后查阅。
关于起子机的安全指示
螺丝可能接触隐藏的电线时，得将机器握住于其绝缘把手表
面。螺丝接触带电电线，会将电导向其他金属部位并引起电
击。
≥ M14 (12.9)/ ≥ M16 (8.8)
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
