M18 BLDD
M18 BLPD
2
3
4
15
9
8
11
13 21
14 M18 BLPD
5
12
16
10
17
6
START
STOP
Remove the battery pack before starting any work on the machine.
在机器上进行任何修护工作之前，先拿出蓄电池。
기기를 사용하지 않을때는 배터리를 빼어두십시요.
Keluarkan pek bateri sebelum memulakan sebarang kerja pada mesin.
6
1
2
2
1
click
Remove the battery pack before
starting any work on the machine.
在机器上进行任何修护工作之
前，先拿出蓄电池。
기기를 사용하지 않을때는
배터리를 빼어두십시요.
Keluarkan pek bateri sebelum
memulakan sebarang kerja
pada mesin.
7
78-100 %
55-77 %
33-54 %
10-32 %
< 10 %
8
3
4
2
1
5
1
1
9
1
2
1
2
10
START
STOP
11
12
LOCK
13
14
M18 BLPD
15
16
1
2
click
17
1
2
18
English
18
TECHNICAL DATA M18 BLDD M18 BLPD
Drilling capacity in steel.........................................13 mm........................................13 mm
Drilling capacity in wood.........................................38 mm.......................................38 mm
Drilling capacity in brick and tile............................._................................................16 mm
Wood screws (without pre-drilling).........................6 mm..........................................6 mm
No-load speed 1st gear..........................................0-450 min-1................................0-450 min-1
No-load speed 2nd gear.........................................0-1800 min-1..............................0-1800 min-1
Impact rate 1st gear................................................_................................................0-7200 min-1
Impact rate 2nd gear..............................................._................................................0-28800 min-1
Torque with battery (Li-Ion 2.0 Ah)*1.......................50 Nm..........................................50 Nm
Torque with battery (Li-Ion 4.0 Ah/5.0 Ah)*.............60 Nm.......................................60 Nm
Battery voltage.......................................................18 V...........................................18 V
Drill chuck range ...................................................1.5-13 mm.................................1.5-13 mm
Weight according EPTA-Procedure 01/2003 (2.0 Ah)..1.7 kg..................................1.8 kg
Weight according EPTA-Procedure 01/2003 (4.0 Ah / 5.0 Ah)..2.0 kg.....................2.1 kg
Noise/vibration information
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound presure level (K = 3 dB(A)).........................94.7 dB(A).................................94.7 db (A)
Sound power level (K=3dB(A))..............................105.7 dB(A)...............................105.7 db (A)
Always wear ear protectors!
Always wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value ah
Percussion drilling into concrete............................13 m/s2 .....................................15.4 m/s2
Uncertainty K=.......................................................1.5 m/s2 .....................................1.5 m/s2
Drilling into metal....................................................0.95 m/s2...................................0.9 m/s2
Uncertainty K=.......................................................1.5 m/s2......................................1.5 m/s2
Screwing.................................................................0.66 m/s2....................................0.9 m/s2
Uncertainty K =......................................................1.5 m/s2......................................1.5 m/s2
*1 Measured according to Milwaukee standard N 877318
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN
60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures, such as maintaining the tool and the accessories, keeping the hands warm and organising
work patterns, to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
English 19
give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Fasteners contacting a „live“ wire may
make exposed metal parts of the power tool „live“ and could
give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing, such
as dust mask, protective gloves, sturdy non-slip footwear,
helmet and ear defenders, is recommended.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g., asbestos).
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined;
• it has pierced through the material to be machined;
• the power tool is overloaded.
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
Sawdust and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. Milwaukee Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Use only System C18 chargers for charging System C18
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case
of eye contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The electronic battery percussion drill/screwdriver may be
used for drilling, percussion drilling, as well as screwdriving for
independent use away from mains supply.
Do not use this product in any other way than stated for
normal use.
BATTERIES
Battery packs which have not been used for some time should
be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life time, the battery packs have to be fully
charged after use.
To obtain the longest possible battery life, remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
• store the battery pack where the temperature is below
27°C and away from moisture;
• store the battery packs in a 30% to 50% charged
condition.
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 2 seconds and turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperature of the
battery could become to high. If this happens, the battery will
shut down.
Place the battery on the charger to charge and reset it.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Always use a side handle when using a 9.0 Ah or higher
capacity battery pack; the output torque of some tools may
increase. If your drill/driver did not come with a side handle,
use the spare part side handle (see explosion drawing of the
tool).
20 繁體中文
警告!
請詳閱所有安全警告及說明，包括隨附於手冊內的安全警告及說
明。若未能遵守警告與指示，可能會導致觸電、火災和/或嚴重受
傷。 請將所有警告與指示存檔以供未來參考。
螺絲刀安全警告
應握住電動工具的絕緣握持面上，因為作業時其緊固件可能會觸及
隱藏線路。碰到「帶電」電線的緊固件會使該電動工具外露的金屬
件同樣「帶電」，從而造成作業人員觸電。
穿戴護耳裝置!暴露於噪音下可能會造成聽力損害。
若有提供附加把手，請使用。機器失控會造成肢體傷害。
螺絲刀安全警告
應握住電動工具的絕緣握持面上，因為作業時其緊固件可能會
觸及隱藏線路。碰到「帶電」電線的緊固件會使該電動工具外
露的金屬件同樣「帶電」，從而造成作業人員觸電。
其他安全和工作指示
操作機器時務必佩戴護目鏡。建議穿戴工作手套、堅固防滑的
鞋具和工作圍裙。
工具操作中引起的粉塵可能有害健康。切勿吸入粉塵。使用吸
塵裝置和配戴合適的防塵面罩。徹底清除堆積的粉塵，像是利
用真空吸塵器。
技術資料 M18 BLDD M18 BLPD
鑽擊力 -- 對金屬.................................13 mm........................13 mm
鑽擊力 -- 對木材.................................38 mm........................38 mm
鑽擊力 -- 對磚瓦.................................xx mm........................16 mm
木螺絲（無預先鑽孔）.............................6 mm.........................6 mm
空載轉速 -- 第一檔...............................0-450 min-1...................0-450 min-1
空載轉速 -- 第二檔...............................0-1800 min-1..................0-1800 min-1
衝擊率 -- 第一檔.................................__...........................0-7200 min-1
衝擊率 -- 第二檔.................................__...........................0-28800 min-1
扭矩 (電池: Li-Ion 2.0 Ah)*......................50 Nm.........................50 Nm
扭矩 (電池: Li-Ion 4.0 Ah/5.0 Ah)*...............60 Nm........................60 Nm
電池電壓.........................................18 V.........................18 V
鑽頭夾盤範圍 ....................................1.5-13 mm....................1.5-13 mm
根據EPTA-Procedure01/2003的重量 (2.0 Ah).........1.7 kg.......................1.8 kg
根據EPTA-Procedure01/2003的重量 (4.0 Ah/5.0 Ah)..2.0 kg.......................2.1 kg
噪音/震動資訊
噪音/震動資訊
依 EN 60745 所測的測量值
一般來說，本工具的A加權躁音標準為:
聲壓量測 (K = 3 dB(A))...........................94.7 dB(A)...................94.7 db (A)
聲壓率級 (K = 3 dB(A))...........................105.7 dB(A)..................105.7 db (A)
穿戴護耳裝置！
穿戴護耳裝置！
依EN 60745所測的振動總值 (三軸向量總和)
震動釋放值ah
衝擊鑽擊水泥.....................................13 m/s2 .....................15.4 m/s2
不確定性 K 值....................................1.5 m/s2 .....................1.5 m/s2
鑽擊金屬.........................................0.95 m/s2.....................0.9 m/s2
不確定性 K 值....................................1.5 m/s2......................1.5 m/s2
扭轉螺絲.........................................0.66 m/s2.....................0.9 m/s2
不確定性 K 值....................................1.5 m/s2......................1.5 m/s2
*1依據Milwaukee 標準 N 877318測量
警告!
本說明書所提供的震動等級是依EN 60745 規定的標準化測試所測得，且可能用於與另一個工具進行比較。該等級可用來初步評估風險。
宣告的震動釋放等級代表的是本工具的主要應用。然而，如果用於不同的應用、使用不同的配件或保養不當，震動釋放也可能不同。這可能
會在總工作時間上顯著增加風險等級。
評估震動暴露的等級還應考慮本工具關機時的時間，或當工具運轉但卻未實際使用的時間。這可能會明顯降低總工作期間的風險等級。
請確認額外的安全措施，以保護操作員不受震動的影響，例如:保養本工具與配件、保持手部溫暖和井然有序的工作方式。
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/