Sony SA-VE525は、映画鑑賞に最適な5.1チャンネルスピーカーシステムです。フロントスピーカー2台、リアスピーカー2台、センタースピーカー1台、サブウーファー1台で構成されており、DVDプレーヤー、LDプレーヤー、ビデオデッキなどの映像機器につなぐことができます。
Sony Digital Cinema Sound、Dolby* Pro Logic、Dolby Digitalに対応しており、迫力のあるサラウンドサウンドを楽しむことができます。また、サブウーファーのレベル調整や、映画や音楽に適したモードの切り替えも可能です。
設置にあたっては、フロントスピーカーとサブウーファーはテレビの左右に、センタースピーカーはテレビの上部に設置します。リアスピーカーは、リスニングポジションの左右または後方に設置してください。スピーカーの角度調整も可能なので、最適なリスニング環境を整えることができます。
このスピーカーシステムで映画や音楽を聴けば、臨場感あふれるサウンドを楽しむことができます。自宅で映画館のような体験
Sony SA-VE525は、映画鑑賞に最適な5.1チャンネルスピーカーシステムです。フロントスピーカー2台、リアスピーカー2台、センタースピーカー1台、サブウーファー1台で構成されており、DVDプレーヤー、LDプレーヤー、ビデオデッキなどの映像機器につなぐことができます。
Sony Digital Cinema Sound、Dolby* Pro Logic、Dolby Digitalに対応しており、迫力のあるサラウンドサウンドを楽しむことができます。また、サブウーファーのレベル調整や、映画や音楽に適したモードの切り替えも可能です。
設置にあたっては、フロントスピーカーとサブウーファーはテレビの左右に、センタースピーカーはテレビの上部に設置します。リアスピーカーは、リスニングポジションの左右または後方に設置してください。スピーカーの角度調整も可能なので、最適なリスニング環境を整えることができます。
このスピーカーシステムで映画や音楽を聴けば、臨場感あふれるサウンドを楽しむことができます。自宅で映画館のような体験
SA-VE525 (GB/CS) 4-233-674-61(1)
2001 Sony Corporation Printed in China
eE Ee
Ee
Ee Ee
Ee
Ee Ee
LINE IN
WOOFER OUT
FRONT
CENTER
REAR
R
R
L
L
A
R
L
R
L
Ee Ee
SPEAKER
IN
SPEAKER
OUT
e
e
E
E
eE Ee
Ee
FRONT
CENTER
REAR
R
R
L
L
Ee
Ee Ee
B
E
e
E
e
E
e
E
e
C
English
Hooking up the system
Connect the speaker system to the speaker output
terminals of an amplifier.
Make sure power to all components (included the
subwoofer) is turned off before starting the hook-up.
Hookup A
This configuration is used when the amplifier is
connected to a DVD player, LD player, VCR or other
video devices.
Hookup B
Try this configuration instead of “Hookup A” in the
following situations:
—When there are no jacks on the amplifier for a
subwoofer.
—When you want a stronger bass sound from the
subwoofer.
Notes (C)
• Make sure the plus (+) and the minus (–) terminals on
the speakers are matched to the corresponding plus (+)
and minus (–) terminals on the amplifier.
• Be sure to tighten the screws of the speaker terminals
securely as loose screws may become a source of noise.
• Make sure all connections are firm. Contact between
bare speaker wires at the speaker terminals may cause
a short-circuit.
• Do not connect the subwoofer to the amplifier’s
CENTER output terminal (which is for Dolby Pro Logic
or Dolby Digital). No bass sound will output from the
subwoofer if you do.
• For details regarding the connections on the amplifier
side, refer to the manual that was provided with your
amplifier.
Tip
All striped wires are minus (–) in polarity, and should be
connected to the minus (–) speaker terminals.
Front (Right)
Subwoofer
Front (Left)
Rear (Right) Rear (Left)
Amplifier
Rear (Right)
Rear (Left)
Front (Right)
Subwoofer
Front (Left)
Amplifier
Precautions
On safety
• Before operating the system, be sure that the operating
voltage of the system is identical with that of your local
power supply.
• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet,
even if the unit itself has been turned off.
• Unplug the system from the wall outlet if it is not to be
used for an extended period of time. To disconnect the
cord, pull the cord by grasping the plug. Never pull
the cord itself.
• Should any liquid or solid object fall into the system,
unplug the system’s power cord and have the system
checked by qualified personnel before operating it any
further.
• AC power cord must be changed only at the qualified
service shop.
On operation
• Do not drive the speaker system with a continuous
wattage exceeding the maximum input power of the
system.
• If the polarity of the speaker connections are not
correct, the bass tones will be weak and the position of
the various instruments obscure.
• Contact between bare speaker wires at the speaker
terminals may result in a short-circuit.
• Before connecting, turn off the amplifier to avoid
damaging the speaker system.
If you encounter color irregularity on a
nearby TV screen
This speaker system is magnetically shielded to allow it
to be installed near a TV set. However, color
irregularities may still be observed on certain types of TV
sets.
If color irregularity is observed...
c Turn off the TV set once, then turn it on again after
15 to 30 minutes.
If color irregularity is observed again...
c Place the speakers further away from the TV set.
If howling occurs
Reposition the speakers or turn down the volume on the
amplifier.
On placement
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
— Extremely hot or cold
— Dusty or dirty
— Very humid
— Subject to vibrations
— Subject to direct sunlight
On cleaning
Clean the speaker cabinets with a soft cloth lightly
moistened with a mild detergent solution or water. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning your
speaker system, please consult your nearest Sony dealer.
About this manual
The instructions in this manual are for SA-VE525,
Sony Micro Satellite Systems.
The SA-VE525 is a 5.1 channel speaker system
consisting of two front speakers, two rear speakers,
one center speaker, and one subwoofer. It supports
Sony Digital Cinema Sound, Dolby* Pro Logic, and
Dolby Digital and is thus gearedtowards the
enjoyment of movies.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
Micro Satellite System
SA-VE525
4-233-674-61(1)
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To prevent fire, do not Cover the ventilation of the
apparatus with news papers, table-cloths, curtains, etc.
And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place vases on
the apparatus.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
Center
Center
3.5m
3.5m 3.5m
3.5m
3.5m
3.5m
2.5m
2.5m
10m 10m
10m 10m
A
B
A
—
—
C
•
•
•
•
•
•
•
•
•
•
•
•
•
•
c
c
•
•
—
—
—
—
—
SA-VE525 (GB/CS) 4-233-674-61(1)
E
H
G
F
D
ON/STANDBY indicator
AA
BB
Front (Right)
WS-FV10A
Subwoofer
Rear (Right)
Front (Left)
Rear (Left)
Micro Satellite System
SA-VE525
WS-WV10A
(for rear speakers)
WS-TV10A
15º
25º
LEVEL
MODE
MIN MAX
MOVIE
MUSIC
POWER
ON
/
STANDBY
1
2
3
4
Screws
POWER LEVEL MODE
AUTO
OFF
POWER
SAVE
Foot pads
I
J
Center
•
•
•
×
× ×
× ×
× ×
× ×
I
1
2
•
•
• B
•
A
B
•
•
•
•
•
D
A B
•
•
E
1
2
3
4
F
G
H
I
1
2
3
J
English
There is hum or noise in the speaker output.
•Make sure all the connections have been
correctly made.
•Make sure none of the audio components are
positioned too close to the TV set.
The sound has suddenly stopped.
•Make sure all the connections have been
correctly made. Contact between bare
speaker wires at the speaker terminals may
cause a short-circuit.
Specifications
SS-MS525 (front, center, and rear speakers)
Speaker system Full range × 2,
magnetically shielded
Speaker units 5 cm, balance drive
type
Enclosure type Bass reflex
Rated impedance 8 ohms
Power handling capacity
Maximum input power: 120 watts
Sensitivity level 87 dB (1 W, 1 m)
Frequency range 120 Hz - 20,000 Hz
Dimensions (w/h/d)
When attached speaker grille:
Approx. 89 × 144 × 130
mm
When attached supplied speaker stand:
Approx. 89 × 128 × 143
mm
(pointed upwards)
Approx. 89 × 122 × 143
mm
(pointed
downwards)
Mass
When attached speaker grille:
Approx.
750 g
When attached supplied speaker stand:
Approx.
850 g
SA-WMS525 (subwoofer)
Speaker system Active subwoofer,
magnetically shielded
Speaker unit Woofer: 20 cm, cone
type
Enclosure type Advanced SAW type
Reproduction frequency range
26 Hz - 250 Hz
Amplifier section
Rated Power Output 120 W (8 ohms 20 Hz - 20
kHz, THD 0.8%)
Inputs
LINE IN (input pin jack)
SPEAKER IN (input terminals)
Outputs
LINE OUT (output pin jack)
SPEAKER OUT (output terminals)
General
Power requirements 220 V AC, 50/60 Hz
Power consumptions 90 W
1 W (standby mode)
Dimensions (w/h/d) Approx. 230 × 392 ×
464 mm, including front
grille
Mass
Approx. 13.2 kg
Supplied accessories
Foot pads (16)
Center speaker stand (1)
Screw (for the center speaker stand) (1)
Washer (for the center speaker stand) (1)
Audio connecting cord (1)
Speaker connecting cords, 10 m (2)
Speaker connecting cords, 3.5 m (3)
Speaker connecting cords, 2.5 m (2)
Design and specifications are subject to change without
notice.
Adjusting the sound
Slight adjustments to the system can enhance your sound
enjoyment.
Adjusting the subwoofer (I)
1 Set MODE according to the program
source as follows:
Source MODE
DVD, LD, video cassette MOVIE
or other video source
MD, CD, cassette tape MUSIC
or other audio source
2 Rotate LEVEL to adjust the volume.
Set the volume level to best suit your
preference according to the program
source.
Notes
• Some amplifier functions for enhancing the sound may
cause distortion in the subwoofer. If such distortion
occurs, turn off those functions.
• To enjoy high-quality sound, do not turn the
subwoofer volume too high.
• To increase the bass sound from the subwoofer,
connect the system using “Hookup B”.
• The bass sound is enhanced in MOVIE mode rather
than in MUSIC mode. Therefore, if you change the
mode to MOVIE while listening to some sources that
do not include the bass sound, you may not be able to
get the effect.
Setting amplifier to enjoy movies
For the Dolby Digital
If your amplifier is connected internally or externally
with a Dolby Digital processor, you should use the setup
menus for the amplifier to specify the parameters of your
speaker system.
See the table below for the proper settings. For details on
the setting procedure, refer to the manual that was
provided with your amplifier.
Select Micro Satellite Position if a Sony amplifier
provides it.
When “Hookup A” is used
(Speaker setup)
For Set to
Front speakers SMALL
Center speaker SMALL
Rear speakers SMALL
Subwoofer ON (or YES)
When “Hookup B” is used
(Speaker setup)
For Set to
Front speakers LARGE
Center speaker SMALL
Rear speakers SMALL
Subwoofer OFF (or NO)
For the Dolby Pro Logic
If your amplifier is connected internally or externally
with a Dolby Pro Logic processor, you should set the
surround effect mode to “NORMAL” on the amplifier for
your particular speaker system.
For details on the setting procedure, refer to the manual
that was provided with your amplifier.
Troubleshooting
Should you encounter a problem with your speaker
system, check the following list and take the indicated
measures. If the problem persists, consult your nearest
Sony dealer.
There is no sound from the speaker system.
•Make sure all the connections have been
correctly made.
•Make sure the volume on the amplifier has
been turned up properly.
•Make sure the program source selector on the
amplifier is set to the proper source.
•Check if headphones are connected. If they
are, disconnect them.
There is distortion in the subwoofer sound
output.
•Check if any sound-enhancing functions have
been activated on the amplifier. If they have,
turn them off.
Positioning the speakers
Location of each speaker (D)
Each speaker should face the listening position. Better
surround effect will result if all speakers are set at the
same distance from the listening position.
Place the front speakers at a suitable distance to the left
and right of the television.
Place the subwoofer on either side of the television.
Place the center speaker on the top-center of the TV set.
The placement of rear speakers greatly depends on the
configuration of the room. The rear speakers may be
placed on both sides of the listening position A or
behind the listening position B.
Tips
• Movies are best enjoyed in a room that produces no
echoes (as in one with surrounding curtains).
• Music (especially classical music) is best enjoyed in a
room that produces some echo.
Positioning the center speaker
(E)
Attach the center speaker to the supplied speaker stand
and place it on a top of the TV set.
For optimum listening enjoyment, the speaker should
face directly towards the listener. Adjust the angle of the
speaker stand for that purpose.
1 Pass the speaker cord into the hole on
the back of the stand and out from the
hole at the center of the stand.
2 Connect the speaker cord to the speaker
terminal.
3 Using the supplied screw and washer,
secure the speaker to the stand.
Note
Do not remove the supplied speaker grille from the
speaker while attaching the speaker to the speaker stand.
4 Adjust the angle of the speaker stand.
Loosen the two screws under the base to
adjust the angle. Then tighten them again
afterwards.
Setting the speakers
To prevent speaker vibration or movement while
listening, attach the supplied foot pads to the bottom of
the front speakers and rear speakers (
F).
The optional speaker stands (G)
For greater flexibility in the positioning of the speakers,
use the optional WS-FV10A (floor stand),
WS-TV10A (TV stand), or WS-WV10A (wall mount
bracket) speaker stand (available only in certain
countries).
Tip
The height of the front speakers should be adjusted to
about the center of the TV screen (
H).
Listening to the sound (I)
First, turn down the volume on the amplifier. The
volume should be set to minimum before you begin
playing the program source.
1 Turn on the amplifier and select the
program source.
2 Press POWER on the subwoofer.
The ON/STANDBY indicator on the
subwoofer lights up green.
3 Play the program source.
Power turns on and off automatically — Auto
power on/off function
(J)
When the subwoofer is on (i.e, the ON/STANDBY
indicator lights up green) and there is no signal input for
a few minutes, the ON/STANDBY indicator changes to
red and the subwoofer enters power saving mode. While
in this mode a signal is input to the subwoofer, the
subwoofer automatically turns on (auto power on/off
function).
To turn this feature off, slide the POWER SAVE switch
on the rear panel to OFF.
Note
If you turn down the volume level of the amplifier too
low, the auto power on/off function may activate,
causing the subwoofer to enter power saving mode.
-
1
-
2
Sony SA-VE525は、映画鑑賞に最適な5.1チャンネルスピーカーシステムです。フロントスピーカー2台、リアスピーカー2台、センタースピーカー1台、サブウーファー1台で構成されており、DVDプレーヤー、LDプレーヤー、ビデオデッキなどの映像機器につなぐことができます。
Sony Digital Cinema Sound、Dolby* Pro Logic、Dolby Digitalに対応しており、迫力のあるサラウンドサウンドを楽しむことができます。また、サブウーファーのレベル調整や、映画や音楽に適したモードの切り替えも可能です。
設置にあたっては、フロントスピーカーとサブウーファーはテレビの左右に、センタースピーカーはテレビの上部に設置します。リアスピーカーは、リスニングポジションの左右または後方に設置してください。スピーカーの角度調整も可能なので、最適なリスニング環境を整えることができます。
このスピーカーシステムで映画や音楽を聴けば、臨場感あふれるサウンドを楽しむことができます。自宅で映画館のような体験
他の言語で
- English: Sony SA-VE525 User manual