Sony HT-CT350 ユーザーマニュアル

Home Theatre System

HT-CT350

4-181-487-14(1)

Operating Instructions

GB

CT

2

GB

3

The unit is not disconnected from the AC power source

(mains) as long as it is connected to the wall outlet,

even if the unit itself has been turned off.

To reduce the risk of fire, do not cover the ventilation

opening of the apparatus with newspapers, tablecloths,

curtains, etc.

Do not place the naked flame sources such as lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing, and do

not place objects filled with liquids, such as vases, on

the apparatus.

As the main plug is used to disconnect the unit from the

mains, connect the unit to an easily accessible AC

outlet. Should you notice an abnormality in the unit,

disconnect the main plug from the AC outlet

immediately.

Do not install the appliance in a confined space, such as

a bookcase or built-in cabinet.

Do not expose batteries or apparatus with battery-

installed to excessive heat such as sunshine, fire or the

like.

On safety

• Should any solid object or liquid fall into the system,

unplug the system and have it checked by qualified

personnel before operating it any further.

• Do not climb on the subwoofer, as you may fall down

and injure yourself, or system damage may result.

On power sources

• Before operating the system, check that the operating

voltage is identical to your local power supply. The

operating voltage is indicated on the nameplate at the

rear of the subwoofer.

• If you are not going to use the system for a long time,

be sure to disconnect the system from the wall outlet

(mains). To disconnect the AC power cord (mains

lead), grasp the plug itself; never pull the cord.

• AC power cord (mains lead) must be changed only at

the qualified service shop.

On heat buildup

Although the system heats up during operation, this is

not a malfunction. If you continuously use this system

at a large volume, the system temperature of the back

and bottom rises considerably. To avoid burning

yourself, do not touch the system.

On placement

• Place the system in a location with adequate

ventilation to prevent heat buildup and prolong the

life of the system.

• Do not place the system near heat sources, or in a

place subject to direct sunlight, excessive dust, or

mechanical shock.

• Do not place anything at the rear of the subwoofer that

might block the ventilation holes and cause

malfunctions.

• Do not place the system near equipment such as a TV,

VCR, or tape deck. (If the system is being used in

combination with a TV, VCR, or tape deck, and is

placed too close to that equipment, noise may result,

and picture quality may suffer. This is especially

likely when using an indoor antenna. Therefore, we

recommend using an outdoor antenna.)

• Use caution when placing the system on surfaces that

have been specially treated (with wax, oil, polish, etc.)

as staining or discoloration of the surface may result.

WARNING

Precautions

3

GB

• Take care to avoid any possible

injury on the corners of the

subwoofer.

On operation

Before connecting other components, be sure to turn off

and unplug the system.

If you encounter color irregularity on

a nearby TV screen

The system is magnetically shielded to allow it to be

installed near a TV set. However, color irregularities

may still be observed on certain types of TV sets.

If color irregularity is observed...

Turn off the TV set, then turn it on again after 15 to 30

minutes.

If color irregularity is observed

again...

Place the system further away from the TV set.

On cleaning

Clean the system with a soft dry cloth. Do not use any

type of abrasive pad, scouring powder or solvent such

as alcohol or benzine.

If you have any question or problem concerning your

system, please consult your nearest Sony dealer.

Copyrights

This system incorporates Dolby* Digital and Pro Logic

Surround and the DTS** Digital Surround System.

*

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, and the double-D symbol are

trademarks of Dolby Laboratories.

** Manufactured under license under U.S. Patent #'s:

5,451,942; 5,956,674; 5,974,380; 5,978,762;

6,487,535 & other U.S. and worldwide patents

issued & pending. DTS and the Symbol are

registered trademarks & DTS Digital Surround and

the DTS logos are trademarks of DTS, Inc. Product

This system incorporates High-Definition Multimedia

Interface (HDMI™) technology.

HDMI, the HDMI Logo, and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC in the United

States and other countries.

“BRAVIA Sync” is a trademark of Sony Corporation.

“PlayStation” is a registered trademark of Sony

Computer Entertainment Inc.

“x.v.Colour (x.v.Color)” and “x.v.Colour (x.v.Color)”

logo are trademarks of Sony Corporation.

4

GB

Precautions...............................................2

Getting Started

Unpacking................................................5

Positioning the system .............................7

Warning about installing the system’s

speaker to the TV stand or a wall ......9

Connecting the speaker ..........................21

Connecting the TV and player, etc. .......22

Connecting other components................24

Connecting the antenna (aerial) .............25

Connecting the AC power cord (mains

lead) .................................................26

Setting up the sound output of the

connected component ......................26

Playback Options

Index to parts and controls.....................27

Enjoying TV...........................................29

Enjoying other components ...................30

Tuner Functions

Direct tuning ..........................................32

Presetting radio stations .........................33

Listening to the radio .............................33

Naming preset stations...........................34

Viewing the station name or frequency in

the front panel display .....................35

Surround Function

Enjoying the surround effect..................36

“BRAVIA” Sync Features

What is “BRAVIA” Sync?.....................37

Preparing for “BRAVIA” Sync .............37

Enjoying Blu-ray Disc/DVD..................38

(One-Touch Play)

Enjoying the TV sound from the

system ..............................................39

(System Audio Control)

Turning off the system, TV and the

connected components.....................40

(System Power Off)

Using the power saving function ...........40

(HDMI SIGNAL PASS THRU)

Setting the Audio Return Channel function

to off................................................ 41

Advanced Settings

Controlling connected Sony components

with the remote ............................... 42

Changing the input button assignments of

the remote ....................................... 45

Settings and adjustments using the

amplifier menu................................ 47

Additional Information

Troubleshooting .................................... 51

Specifications ........................................ 53

Index...................................................... 56

Table of contents

Getting Started

5

GB

Getting Started

Unpacking

• Subwoofer (SA-WCT350) (1)

• Speaker (SS-CT350) (1)

• AM loop antenna (aerial) (1)

• FM wire antenna (aerial) (1)

• Speaker cord (1)

• Digital optical cord for a TV

(2.5 m) (1)

• Remote commander (RM-

AAU074) (1)

• R6 (size AA) batteries (2)

• WS-CT350EB

• Screws for the extension bracket

(large, +PSW5 × 16 mm) (6)

• Screws for the rear cover (small,

M3 × 8 mm) (1)

• Support belt (1)

• Screw for the support belt

(+PSW4 × 20 mm) (1)

• Wood screw for the support belt

(M3.8 × 20 mm) (1)

•Clamp screw (2)

• Spacer (4)

• Screw for the Wall-Mount

Bracket (+PSW6 × 22 mm) (4)

• Operating Instructions (1)

or

• Extension bracket (1)

• Rear cover A (1)

• Rear cover B (1)

• Rear cover C (1)

• Cover for the TV (1)

continued

6

GB

Inserting batteries into the remote

Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the

markings inside the compartment. To use the remote, point it at the remote sensor in the front panel

display of the subwoofer.

• Do not leave the remote in an extremely hot or humid place.

• Do not use a new battery with an old one.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.

• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage

from battery leakage and corrosion.

Notes

Getting Started

7

GB

The illustrations below are examples of how to install the subwoofer and speaker.

• Do not block the heat ventilation on the rear panel of the subwoofer.

Installing the speaker to the

TV

You can install the speaker with the following

TV models (not supplied):

• Installing the speaker on the TV stand

(page 12)

• Hanging the speaker and TV on a wall

(page 15)

Installing the speaker and the

TV separately

If you cannot install the speaker to the TV, you

can install the speaker as shown below.

• Installing the speaker in a rack

• Installing the speaker on a wall (page 20)

Positioning the system

Note

KDL-40NX800, KDL-46NX700,

KDL-40NX700, KDL-46HX800,

KDL-40HX800, KDL-46EX700,

KDL-40EX700, KDL-46EX710,

KDL-40EX710, KDL-40EX600,

KLV-40EX600

continued

8

GB

Connecting the speaker cord to the speaker

The connectors of the speaker cord are color-coded depending on the type of speaker. Connect the

connectors of the speaker cord to match the color of the speaker jacks.

1 Remove the screw of the cover at the rear of the speaker, and then remove the cover.

2 Connect the speaker cord.

3 Guide the speaker cord through the square notch at the bottom of the cover, and then

reattach the cover to the speaker and secure it with the screw removed in step 1.

If you install the speaker to the TV, do not reattach the cover. Perform the steps in “Installing the

speaker on the TV stand” (page 12), or “Hanging the speaker and TV on a wall” (page 15).

• When you install the speaker or a TV on a wall, be careful not to stumble over the cord connected to the speaker.

• Be careful not to pinch the speaker cord when you reattach the cover.

Notes

R CENTER L

Green

White

Red

A Speaker cord

(supplied)

A

Rear of the speaker

Getting Started

9

GB

To Customers

Sufficient expertise is required for installing this

product. Be sure to subcontract the installation to

Sony dealers or licensed contractors and pay

special attention to safety during the installation.

Sony is not liable for any damages or injury

caused by mishandling or improper installation,

or installing anything other than the specified

product. Your statutory rights (if any) are not

affected.

On Safety

Products by Sony are designed with safety in

mind. If the products are used incorrectly,

however, it may result in a serious injury through

fire, electric shock, the product toppling over, or

the product dropping. Be sure to observe the

precautions for safety to prevent such accidents.

WARNING

If the following precautions are not observed,

serious injury or death through fire or electric

shock, the product toppling over or falling can

result.

Do not drop the products or install them

where there is a possibility of them falling

down.

• Be sure to subcontract installing, moving or

dismounting the products to licensed

contractors and keep small children away

during the procedure.

• Unauthorized installation may result in serious

injury or property damage.

• Having an unauthorized dealer carry or

dismount the SS-CT350 speaker or SS-CT350

speaker-installed TV may lead to the products’

falling and result in serious injury or property

damage. Make sure that two or more persons

carry or dismount the product(s).

• Do not remove screws, etc., after mounting the

SS-CT350 speaker or SS-CT350 speaker-

installed TV.

• Do not handle the products with excessive

force during cleaning or maintenance.

• If you hang the SS-CT350 speaker or SS-

CT350 speaker-installed TV on a fragile wall

or a wall whose surface is not flat or

perpendicular, the product(s) may fall and

cause injury or property damage.

• If the SS-CT350 speaker or SS-CT350

speaker-installed TV is not installed firmly on

the wall, the product(s) may fall and cause

injury or property damage.

Do not place any object on the products.

• Do not put anything on the products. If you do

so, the system may fall and cause injury or

property damage.

Warning about installing the system’s speaker to the TV

stand or a wall

continued

10

GB

Do not lean or hang on the products.

• Do not lean or hang on the products, as they

may fall on you and cause serious injury.

Pay attention to the location.

• Do not install the products on wall surfaces

such as a pillar, where the corners or the sides

of the products protrude away from the wall

surface. If a person or object happens to hit the

protruded corner or side of the products, it may

cause injury or property damage.

• Do not expose the products to rain or moisture,

or spill liquid of any kind on them. It may cause

a fire or electric shock.

• Never place the products in hot, humid or

excessively dusty places, or in a place where

they are subject to mechanical vibrations.

Doing so may cause a fire or electric shock.

• Keep flammable objects or open flames (e.g.,

candles) away from the products.

• Do not install the products over or under an air-

conditioner. If the products are exposed to

wind from the air conditioner for an extended

period of time, or get wet by water leakage

from the air conditioner, this may cause a fire,

an electric shock, or malfunctions.

Do not allow the cords to be pinched.

• If the AC power cord (mains lead) or

connecting cords are pinched between the

products and the wall, floor, or other object, or

bent or twisted by force, the internal

conductors may become exposed and cause a

short circuit or an electrical break. This may

cause a fire or an electric shock.

• Do not step on the AC power cord (mains lead)

or connecting cords when you carry the

products. The cord may be damaged, and this

may result in a fire or electric shock.

Do not cover the ventilation holes of the

products.

• If you cover the ventilation holes (with a cloth,

etc.), heat may build up inside and cause a fire.

Do not stumble over the cords.

• You may trip, or may cause the products to

topple over and cause injury.

Getting Started

11

GB

CAUTION

If the following precautions are not observed,

injury or property damage may occur.

Do not install any equipment other than the

specified product.

• The WS-CT350EB accessories (supplied) are

designed for use with the specified equipment

only. If you install equipment other than that

specified, it may fall or break, and cause injury.

• Do not modify the products.

• Do not place anything hot directly on the

products. The heat may cause discoloration or

deformation of the products.

Be sure to secure the system’s speaker and

TV.

• Secure the SS-CT350 speaker and TV firmly

when installing them together. Then, secure the

SS-CT350 speaker-installed TV firmly on the

stand or wall. If the SS-CT350 speaker and TV

are not installed securely, they may fall or

topple over, and cause injury.

Do not apply weight to the products or

subject them to any kind of impact.

• When installing the SS-CT350 speaker to a TV

stand or hanging the SS-CT350 speaker -

installed TV on a wall, do not apply weight to

the speaker or TV with your hand. Do not hit

the speaker or TV with hard objects, such as a

screwdriver, etc.

When moving the SS-CT350 speaker-

installed TV

If you move the products forcefully, damage or

injury may result. Be sure to follow the proper

procedures and advice given below.

• Be sure that two or more persons carry the SS-

CT350 speaker-installed TV, and only after

unplugging and removing the connected

equipment.

• Be careful not to allow your hands or feet to be

pinched under the bottom of the SS-CT350

speaker-installed TV.

• When carrying the SS-CT350 speaker-

installed TV, do not hold it by the SS-CT350

speaker part. Doing so may cause damage or

injury.

• Do not drag the SS-CT350 speaker-installed

TV. The base part may come off and damage

the floor.

Notes on installation

• When assembling, spread a cloth on the floor to

avoid damaging the floor.

• Install the products on a solid and flat floor.

• Be sure that two or more persons install the

products. Doing it alone may result in an

accident or injury.

• Be sure to keep children away during the

process.

Be sure to install the products securely

following the instructions.

• Tighten the screws securely. If the SS-CT350

speaker is not installed securely, it may fall and

cause damage or injury.

• Be careful not to pinch your fingers or hands

when assembling the products.

Notes on installation on a wall

• If you use the products installed on a wall for a

long time, the wall behind or above the

products may become discolored or the

wallpaper may come unstuck, depending on

the material of the wall.

• If the products are removed after installed on

the wall, the screw holes will remain.

• Consult your licensed contractor regarding an

appropriate location (free from radio noise,

etc.) before installing.

continued

12

GB

Installing the speaker on the TV stand

You can install the speaker with the following TV models (not supplied):

• KDL-40NX800, KDL-46NX700, KDL-40NX700, KDL-46HX800, KDL-40HX800,

KDL-46EX700, KDL-40EX700, KDL-46EX710, KDL-40EX710, KDL-40EX600, KLV-40EX600

Although the shape of the TV stand base differs depending on the TV model, you can install the speaker

on the TV stand following this procedure.

1 Remove covers 1 and 2 from the rear of the TV.

For details on removing the covers, refer to the operating instructions of the TV.

• Some Sony TVs do not have cover 2.

2 Remove the screws of the TV, and then detach the TV from the TV stand.

• Make sure to place the TV on a soft thick cloth with the screen side down to prevent damaging the surface of

the LCD.

Note

Cover 2

Cover 1

Getting Started

13

GB

3 Secure the extension bracket (supplied) to the TV stand with the large screws (+PSW5

× 16 mm) (supplied).

4 Secure the speaker to the extension bracket with the large screws (+PSW5 × 16 mm)

(supplied).

5 Reattach the TV.

Extension bracket

continued

14

GB

6 Secure the TV with the screws removed in step 2.

7 Attach the rear covers A, B, and C (supplied).

Secure the rear cover A to the extension bracket with the small screw (M3 × 8 mm) (supplied).

Guide the speaker cord through the rectangular notch of the rear cover B, and insert the three

projecting parts of the rear cover B into the holes on the extension bracket and the speaker.

Insert the three projecting parts of the rear cover C into the holes on the extension bracket and the

speaker.

• When carrying the SS-CT350 speaker-installed TV, do not hold it by the SS-CT350 speaker part. Doing so

may cause damage or injury.

• The rear cover A is used only for the following TV model: KDL-40NX800, KDL-40/46NX700.

Notes

Rear cover A

Rear cover C

Rear cover B

Getting Started

15

GB

8 Attach the cover for the TV (supplied) and cover 1 removed in step 1.

Insert the two projecting parts of the cover for the TV into the holes on the TV.

For details on attaching cover 1, refer to the operating instructions of the TV.

• The cover for the TV is used only for the following TV model: KDL-40NX800 (You can attach cover 2 instead

if it was supplied with your TV.)

• As a protective measure, secure the TV. For details, see “Preventing the TV from toppling over” (page 18).

Hanging the speaker and TV on a wall

You can hang the speaker with the following TV models (not supplied):

• KDL-40NX800, KDL-46NX700, KDL-40NX700, KDL-46HX800, KDL-40HX800,

KDL-46EX700, KDL-40EX700, KDL-46EX710, KDL-40EX710, KDL-40EX600, KLV-40EX600

• To hang the TV on the wall, refer to the operating instructions of the TV and the Wall-Mount Bracket.

1 Remove covers 1 and 2 from the rear of the TV.

For details on removing the covers, refer to the operating instructions of the TV.

• Some Sony TVs do not have cover 2.

Note

Cover for the TV

Cover 1

Cover 2

Cover 1

continued

16

GB

2 Remove the screws of the TV, and then detach the TV from the TV stand.

3 Secure the speaker to the extension bracket with the large screws (+PSW5 × 16 mm)

(supplied).

4 Reattach the TV.

• Make sure to place the TV on a soft thick cloth with the screen side down to prevent damaging the surface of

the LCD.

Note

Cloth

Getting Started

17

GB

5 Secure the TV with the screws removed in step 2.

6 Hang the TV on the wall.

For details on hanging the TV on the wall, refer to the operating instructions of the TV.

• When hanging the SS-CT350 speaker-installed TV on the wall or taking it off the wall, do not hold it by the SS-

CT350 speaker part. Doing so may cause damage or injury.

When hanging TV model KDL-46HX800, KDL-40HX800, KDL-46EX700,

KDL-40EX700, KDL-46EX710, KDL-40EX710, KDL-40EX600, KLV-

40EX600 using the Wall-Mount Bracket (SU-WL500, not supplied)

You can only adjust the angle of the SS-CT350 speaker-installed TV to 0° or 5° downward. If you want

to set the TV’s angle to 10°, 15° or 20° downward, install the SS-CT350 speaker directly on the wall.

When hanging TV model KDL-40NX800, KDL-46NX700, KDL-40NX700

using the Wall-Mount Bracket (SU-WL700, not supplied)

Place the Spacers (supplied) between the TV and the Wall-Mount Bracket, and then secure them using

the Screws for the Wall-Mount Bracket (supplied).

Use the Spacers and Screws for the Wall-Mount Bracket supplied with the system. Do not use spacers

supplied with certain TVs.

Note

Spacer

continued

18

GB

Preventing the TV from toppling over

As a protective measure, secure the TV. If you fail to do so, the TV may topple over resulting in serious

injury.

• To avoid injury, place the SS-CT350 speaker-installed TV less than 25 cm from the wall, and firmly secure the TV

to the wall.

• Be careful not to pinch your fingers when setting up the TV or rack.

• Install the TV after allowing for a space of less than 25 cm from the wall. The wall will prevent the TV from falling

even if the TV leans backward towards the wall.

When installing the TV on a rack

1 Place the TV on the center of the rack.

2 Fit the support belt (supplied) to the TV, then firmly fasten with the screw for the support

belt (+PSW4 × 20 mm) (supplied) using a screw driver.

3 Fasten the support belt to the rack with the wood screw for the support belt (M3.8 × 20

mm) (supplied).

Warning

Notes

Screw for the support belt

(+PSW4 × 20 mm)

Wood screw for the support belt

(M3.8 × 20 mm)

Getting Started

19

GB

Securing the TV to a wall

Prepare strong string or chain (not supplied) and a fastener (not supplied) for fastening to the wall.

Secure the fastener to a reinforced wall.

Even if you have secured the TV to the rack, be sure to secure it to a wall following this procedure.

1 Fasten the clamp screws (supplied) to the rear of the TV.

2 Secure the fastener to the wall (1), and then thread the string or chain through the holes

of the clamp screws and the fastener (2). Firmly tie both ends of the string or chain

together.

Clamp screw

1

2

Less than

25 cm

Less than

25 cm

TV installed on the floor TV installed on a rack

continued

20

GB

Installing the speaker on a wall

You can install the speaker on the wall.

• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach

the screws securely to a wall beam. Install the speaker on a vertical and flat reinforced area of the wall.

• Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety

during the installation.

• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength,

improper screw installation or natural calamity, etc.

1 Prepare screws (not supplied) that are suitable for the holes on the back of the speaker.

See the illustrations below.

2 Fasten the screws to the wall. The screws should protrude 6 to 7 mm.

3 Hang the speaker onto the screws.

Align the holes on the back of the speaker to the screws, then hang the speaker onto the two screws.

Notes

Hole on the back of the speaker

4mm

more than 25 mm

5mm

10 mm

265 mm

6 to 7 mm

ページが読み込まれています...

Sony HT-CT350 ユーザーマニュアル

Sony HT-CT350 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント