EN USER GUIDE
COOKER HOOD
烟机
CN 使用手册
•
1
274
mm
900 mm
60 mm
500 mm
331 mm
Min 650 - Max 1002 mm
Min 750 - Max 1102 mm
542 mm
I
•
1
1 x C
1 x F
1 x J
1 x L
5 x D/E
1 x H
1 x K
+
2 x M
2 x Q
2 x P
1.1
1 x G 1 x N
1.2
II
•
2
125
150
125
150
B
A
C
D
E
2.1
2.2
2.3
III
K
•
2
90°C
2cm
1
2
3
2.3.1
2.3.2
IV
•
2
F
H
I
G
H
I
K
J
P
L
2.4
V
M
M
•
4
•
3
4
VI
3
DEAR CUSTOMER,
EN
Discovering a De Dietrich product means experiencing
the range of unique emotions.
The attraction is immediate, from the moment you set eyes
on the product. The sheer quality of the design shines through,
thanks to the timeless style and outstanding finishes which make
each component an elegant and refined masterpiece in its own
right, each one in perfect harmony with the others.
Next, comes the irresistible urge to touch it.
De Dietrich design makes extensive use of robust and prestigious
materials, where the accent is place firmly upon authenticity.
By combining state-of-the-art technology with top quality materials,
De Dietrich produces
beautifully crafted products to help you get the most from the
culinary arts, a passion shared by all lovers of cooking and fine
food. We hope that you enjoy using this new appliance.
Thank you for choosing a De Dietrich product.
CONTENTS
Important safety advice and precautions........................................
Identification ....................................................................................
Installation.......................................................................................
Electrical connection..........................................................................
Use in evacuation mode ....................................................................
Use in recycling mode........................................................................
Fitting the hood ..................................................................................
Fitting the duct....................................................................................
Use....................................................................................................
Automatic mode ................................................................................
Selecting the type of hob ..................................................................
Changing to automatic mode..............................................................
Switching on/off ...............................................................................
Saturated filter cassettes ..................................................................
Saturated carbon filters ......................................................................
Changing speed..................................................................................
Configuration in recycling mode ........................................................
Time delay / deferred stop..................................................................
Eolysis function..................................................................................
Eolysis function programming............................................................
Fan auto-stop......................................................................................
Light auto-stop....................................................................................1
Care....................................................................................................1
Problems ..........................................................................................1
Environment......................................................................................1
Customer service..............................................................................
EN
9
IMPORTANT SAFETY ADVICE AND PRECAUTIONS
These instructions are also available on the brand’s web site.
Please read this advice carefully before installing and using your appliance. These
instructions are intended to protect your safety and the safety of others. Keep this
manual with the appliance. If you sell or give the appliance to someone else, make
sure that you also give them this manual.
• With a view to constantly improving our products, we reserve the right to make
changes to their technical, functional or aesthetic characteristics in line with
technological progress.
• To easily locate the make, model number, etc. of your appliance, we recommend
that you note this information on the “After-Sales Service Department and Customer
Support” page.
Important precautions
• This appliance was designed for use by private persons in their
homes. Do not use it for commercial or industrial purposes or for
any other purpose than that for which it was designed.
• When you receive the appliance, unpack it or have it unpacked
immediately. Check its general appearance. Make a note of any
reservations on the delivery slip and keep a copy.
• This appliance can be used by children aged under 8 and by
persons with diminished physical, sensory or mental capacities, or
persons without any experience or knowledge, provided that they
are properly attended to or are given the instructions on how to use
the appliance in complete safety and that any potential risks are
anticipated. Children must not play with the appliance. The
appliance must not be cleaned or maintained by unsupervised
children.
• Caution: The accessible parts of this appliance may become hot
when used with cooking appliances.
• The appliance can be disconnected by using an accessible
power outlet or by incorporating a switch in the fixed lines,
in accordance with installation rules.
• Do not modify or attempt to modify any of this appliance’s
characteristics. Doing so could be dangerous.
• The appliance should only be repaired by an approved specialist.
10
IMPORTANT SAFETY ADVICE AND PRECAUTIONS
• Always disconnect the hood before carrying out cleaning or mainte-
nance.
• Never use steam or high-pressure tools to clean your appliance (due
to electrical safety considerations).
Risk of asphyxiation
• Regulations on the evacuation of air must be complied with. Air must
not be sent into a duct used to evacuate fumes from appliances that
use gas or other fuels (this does not apply to appliances that only
emit air into the room).
• The room must be suitably ventilated when the cooker hood is used
at the same time as appliances that use gas or other fuels (this does
not apply to appliances that only emit air into the room).
Risk of fire
• Flambé-ing food or turning on gas rings below the hood, unless they
are covered by a pan is prohibited, since the flames could be sucked
in and damage the appliance.
• Keep a constant watch on fryers used below the hood. When heated
to very high temperatures, oil and fat can catch fire.
• Clean the appliance and replace filters at the recommended fre-
quency. Accumulated deposits of grease could cause a fire.
• Using the hood above a solid fuel range (wood, coal, etc.) is prohi-
bited.
• If the hood is installed above a gas-fired appliance, leave at least
65 cm between the top of the hob and the underside of the hood. If
the instructions for a hob installed below the hood specify a distance
greater than 65 cm, then that distance must be applied.
11
•
1
IDENTIFICATION
1.1 - PARTS LIST
C - Drilling template
D/E - Plug and + screws (duct support)
F - Duct support
J - Adapter
H - Duct
K - Fixing bracket
L - Hood
M - Screws (for fixing duct)
Q - Screws (for fixing motor)
P - Spacer
1.2 - OPTIONAL RECYCLING KIT
G - Fume deflector
N - Carbon filters
These parts are available from AFTER-
SALES SERVICE
12
•
2
INSTALLATION
ELECTRICAL CONNECTION
During installation and maintenance ope-
rations, the appliance must be disconnec-
ted from the mains; fuses must be
isolated or removed.
The electrical connections should be
made before the appliance is installed in
its housing.
Check that:
- the electrical installation is sufficiently
rated,
- the supply wires are in good condition,
- the diameter of the wires complies with
the installation requirements.
This appliance is supplied fitted with a
3-
core (phase, neutral and earth)
0.75mm
2
H 05 VVF cable. It must be
connected to a 220-240V single phase
mains network via a socket which must
remain accessible after ins-tallation, in
accordance with the installa-tion rules.
The fuse in your installation must be 10
or 16A. If the mains cable is damaged,
call after-sales service and so avoid any
danger.
If the electrical installation in your home
requires any changes in order to connect
your appliance, contact a professional
electrician.
If the hood malfunctions in any way, un-
plug it or remove the fuse for the circuit
concerned.
The installation must comply with current
regulations for the ventilation of rooms. In
particular, air must not be evacuated into
a duct used to evacuate fumes from ap-
pliances using gas or other fuels. Disused
ducts may only be brought into service, if
approved by a competent specialist. The
evacuation line, whatever its type, must
not emerge in a loft space
.
2.1 - USE IN EVACUATION MODE
You have a duct that leads outside.
Your hood may be connected to it via an
evacuation duct (minimum 125mm dia.,
made of enamelled, aluminium hose or
other non-flammable material). If your
duct is less than 125mm in diameter, you
must change to recycling mode.
2.2 - USE IN RECYCLING MODE
You do not have a duct leading to the out
-
side.
All our appliances can operate in recy-
cling mode.
In such a case, purchase a recycling kit
comprising a set of active carbon filters
and a deflector.
Energy saving advice
To obtain the best performance from your
appliance, limit the number of bends and
length of the duct as much as possible.
2.3 - FITTING THE HOOD
The minimum distance between the coo-
king surface (2.3) and the lowest part of
the hood is 65cm. If the instructions for a
hob installed below the hood specify a
distance greater than 65 cm, then that
distance must be applied.
- Draw a horizontal line (A) at least 65cm
above the cooking surface.
- Draw a vertical line (B) on the wall, cen-
tred on the cooking surface running
from the ceiling to the previous horizon-
tal line (A).
- Place the drilling guide (C) against the
wall.
- Drill the two holes. Install the plugs.
For hollow walls, use suitable plugs and
screws (2.3).
•
2
INSTALLATION
13
- Screw the fixing bracket (K) to the wall
with the two screws (D) (2.3.1).
- Attach the suction hood using the sus-
pension fittings.
- Adjust the height and level, using the
s
upport adjustment screws (the top
screw for horizontal adjustment and the
lower screw for contact with the wall).
Caution: manually tighten without forcing
- Fit the locking screw that prevents the
appliance being lifted off the suspension
fittings (E).
Remove the adhesive tape from the en-
closure
- Lift the enclosure approximately 2cm
and then release it, make it move a
quarter turn and then slide it and secure it
with the two screws (Q) on the front of the
motor.
Take care not to damage the cables du-
ring rotation and fixing.
2.4 - FITTING THE DUCT
•Evacuation outside
- Fix the metal duct support at ceiling
height, using the two screws (D/E).
- For a 125mm diameter duct, use the
adapter supplied (J).
If your duct to the outside is less than
125mm in diameter, you must connect
your hood in recycling mode.
- Push the end of the duct on to the motor
outlet.
- Prepare your telescopic duct, taking
care to hide the ears.
- Push the duct, assembled thus, on to
the hood and lift the upper part to adjust
the height and then screw it on to the
metal duct support using the two
screws (M).
• Recycling (optional kit - available
from after-sales service)
- Fix the plastic fume deflector (G)
against the wall at ceiling height with
the two screws. Take care to centre the
deflector with reference to the vertical
line (B) drawn on the wall.
Add the two spacers (P), supplied in the
product pouch, to the deflector.
- Push one end of the duct on to the de-
flector and the other end on to the
motor outlet.
- Prepare the duct, taking care to position
the ears at the top, so that they are vi-
sible (H).
- Push the duct, assembled thus, on to
the hood and lift the upper part to adjust
the height and then screw it on to the
fume deflector using the two screws
(M).
•
3
USE
Note
This installation and user guide covers
several models. Slight differences in the
details and equipment may appear bet-
ween your appliance and the descriptions
given.
When the appliance is switched on for the
first time, all the touch keys light and then
switch off.
Automatic mode
These hoods have an in-built ability to
adapt. Fitted with sensors, they trigger
automatically when they detect any heat
or emitted steam, adapt the suction
speed spontaneously and switch off once
the last fumes have been evacuated.
Hob type selection and sensitivity ad-
justment
To select your hob type, first switch off the
hob.
Hold the key pressed to enter confi-
guration mode; the key flashes ra-
pidly and another key lights up.
Press the key to select an induction
hob,
Press the key to select a ceramic
hob,
Press the key to select an electric
hob,
You can refine your hood’s reaction time
in automatic mode:
- give a short press on the key which
then flashes more slowly; you can then
adjust the sensitivity.
- give a short press on the key for
more sensitive detection.
- give a short press on the key for
medium-sensitive detection.
- give a short press on the key for
less sensitive detection.
Your configuration is confirmed automa-
tically after 10 seconds or after a short
press on the key.
All the keys light up one after the other
and your selections are saved.
Changing to automatic mode
Give a short press on the key (
flashes). Automatic mode is active.
The hood starts when it detects heat; the
key is lit.
The hood stops after 40 seconds or
10 minutes depending on the length of
time heat is detected.
Hood switch-off in automatic mode
If you are in automatic mode and you
want to switch off the hood, press the
key.
On/Off
Pressing the key starts the hood in
speed 1.
A long press on the key stops the
hood.
Saturated filter cassettes
The key flashes (1 short flash) for
2 minutes after the hood is switched off
to indicate that the filter cassettes should
be cleaned (see the “cleaning the filter
cassette” section).
Hold the key press (for at least
2 seconds) to reinitialise the “saturation”
function.
14
15
•
3
USE
Saturated carbon filters
The key flashes (2 short flashes) for
2 minutes after the hood is switched of
f
to indicate that the carbon filters should
be changed (see the “changing the car-
bon filter” section).
Hold the key pressed (for at least
5 seconds) to reinitialise the “saturation”
function.
Changing speed
After the hood has been started, you can
change the suction speed by pressing on
speed 2 (the key lights) or for
speed 3 (the key lights) for
10 minutes and then speed 2.
Configuring recycling mode
Your hood must be switched off.
By default the hood is in evacuation
mode.
Pressing and holding the and
keys together (for at least 2 sec) allows
you to switch between Evacuation and
Recycling modes. The and keys
light and the or keys flash.
A short press on the key selects re-
cycling mode (the key flashes and the
key switches off).
A short press on the key selects
evacuation mode ( key and the
key switches off).
A short press on the key confirms
the configuration (or automatically
confirmed after 10 seconds).
Time delay / deferred stop
At the end of cooking, you can press the
key to switch off the hood. This func-
tion maintains suction at the selected
speed for 10 minutes; the key flashes
and power remains on.
To cancel the deferred stop, press the
key again and the deferred stop is can-
celled.
Light
A short press on the key switches
the light on the hood on and off. With
each long press on the key, the
brightness is reduced by 25% for each
second the key is held pressed.
Eolysis function
A short press on the key starts the
function. For 1 hour the hood alternates
between 5 minutes at speed 1 with
10 minutes off; the key is lit and the
key flashes.
After 1 hour, the hood switches off on its
own. To interrupt this function, press the
key again.
Programming the Eolysis function
A long press on the key activates
programming.
The key flashes alternately with the
key, indicating the start of program-
ming.
The number of presses on the key is
the desired number of program hours
(maximum 9 = 9 hours).
16
•
3USE
The key flashes alternately with the
key (the number of successive flashes
is the number of hours selected).
The program is confirmed automatically
after 25 seconds or by a short press on
the key (the key flashes alterna-
tely with the key).
To cancel programming, press the
key.
Fan auto-stop
If you forget to switch off your hood, it will
switch off automatically after 9 hours.
Light auto-stop
If you forget to switch off the light on your
hood, it will switch off automatically after
9 hours.
Energy saving advice
Adjust the speed to the cooking mode
and the number of pans. Use the rear
burners on your hob for preference.
17
•
4CARE
4.1 - CLEANING THE FILTER CAS-
SETTES
They must be cleaned after every
30 hours approximately of use or at least
once a month. Use a brush, warm water
and a mild detergent. Rinse and dry them
carefully before putting back in place.
4.2 - CHANGING THE CARBON FIL-
TER
This filter holds odours; it should be re-
placed after approximately 120 hours of
use.
Order these filters from your dealer.
- Remove the filter cassettes.
- Remove the two metal fixings (4)
- Remove the carbon filters (3)
- Fit new filter on to the filter cassettes.
- Re-position the 2 fixings (4).
- Fit the filter cassette back in place.
- Repeat this operation for all filter cas-
settes.
CLEANING THE OUTER SURFACES
To clean the outer surfaces on your
hood, use soapy water and do not use
scouring creams or scouring sponges.
4.3 - CHANGING THE LED LAMPS
Contact after sales service.
18
•
5PROBLEMS
The hood does not work.
Check that:
• there is not a power cut.
• a speed has actually been selected.
The hood is not coping.
Check that:
• the motor speed selected is sufficient
for the quantity of fumes or steam
released.
• the kitchen is sufficiently ventilated to
allow air to be taken in.
• the carbon filter is not saturated (hood
in recycling mode).
The hood stops during operation.
Check that:
• there is not a power cut.
• the all-pole cut-off device has not
tripped.
19
•
6ENVIRONMENT
CARE FOR THE ENVIRONMENT
This appliance’s packaging can be
recycled. Recycle and contribute towards
protecting the environment by disposing
of packaging in local waste containers
designed for this purpose.
Your appliance also contains a
lot of recyclable material. This
logo indicates that used
appliances must not be mixed
with other waste.
Appliance recycling organised by your
manufacturer is carried out under
optimum conditions, in accordance with
European Directive 2002/96/EC on the
disposal of waste electrical and
electronic equipment.
Contact your local authority or retailer for
information on used appliance collection
points close to your home.
Thank you for helping to protect the
environment.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
