Tektronix WFM5200 series Instructions Manual

xx

WFM5200

Waveform Monitor

Installation and Safety

ZZZ

Instructions

*P071288702*

071-2887-02

WFM5200

Waveform Monitor

Installation and Safety

ZZZ

Instructions

xx

www.te ktronix.com

071-2887-02

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges rese rved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverto

n, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

Preface ............................................................................................................... 1

Accessories ..................................................................................................... 2

Documentation................................................................................................. 3

General Safety Summary .......................................................................................... 5

Compliance Information ........................................................................................... 7

EMC Compliance.............................................................................................. 7

Environmental considerations................................................................................ 8

Operating Requirements ........................................................................................... 9

Electrical Ratings .............................................................................................. 9

Environmental Ratings....................................................................................... 10

Physical Speciﬁcations....................................................................................... 11

Rear-Panel Connectors............................................................................................ 12

Input and Output Connectors ................................................................................ 12

Basic Installation Procedure...................................................................................... 15

Installing in a Video System ......... .................................. .................................. .... 16

Power-On and Power-Off Procedure ............................................................................ 19

Front-Panel Controls .............................................................................................. 20

はじめに.................................................................................................. 22

アクセサリ ............................................................................................ 23

マニュアル ........................................................................................... 24

安全にご使用いただくために .......................................................................... 26

適合性に関する情報.................................................................................... 28

EMC 適合性......................................................................................... 28

環境に関する考慮事項 ............................................................................ 29

動作の要件 .............................................................................................. 30

電気定格 ............................................................................................ 30

環境要件 ............................................................................................ 32

物理仕様 ............................................................................................ 32

リア・パネル・コネクタ.................................................................................... 33

入出力コネクタ ...................................................................................... 33

基本的な設置手順 ...................................................................................... 36

ビデオ・システムへの設置.......................................................................... 37

電源投入、電源切断の手順............................................................................ 40

フロント・パネル・コントロール .......................................................................... 41

前言 ...................................................................................................... 43

附件 .................................................................................................. 44

文档 .................................................................................................. 45

WFM5200 Installation and Safety Instructions i

Table of Contents

常规安全概要 ........................................................................................... 47

符合性信息 .............................................................................................. 49

EMC 符合性 .......................................................................................... 49

环境注意事项....................................................................................... 50

操作要求................................................................................................. 51

电源额定值.......................................................................................... 51

环境额定值.......................................................................................... 52

物理技术规格....................................................................................... 53

后面板连接器 ........................................................................................... 54

输入和输出连接器 ................................................................................. 54

基本安装步骤 ........................................................................................... 57

在视频系统中安装 ................................................................................. 58

开机和关机步骤

........................................................................................ 61

前面板控件 .............................................................................................. 62

ii WFM5200 Installation and Safety Instructions

Preface

This document contains the following information:

Important safety precautions to avoid injury and prevent damage to this

product or any products connected to it

EMC (electromagnetic compliance), safety, and environmental standards

with which the instrument complies

Voltage, power, and environmental requirements to use the product

Installation procedure

Power-on and power-off procedure

Front-p

anel and rear-panel features

WFM5200 Installation and Safety Instructions 1

Preface

Accessories

Unpack the instrument and check that you have received all of the items listed in

the following table as standard accessories. You can order optional accessories

separately. You may want to save the shipping carton and packing materials

(including the a nti-static bag) in case you need to ship the instrument. Check our

Web site (ww

w.tektronix.com) for the most current information on accessories.

Accessory Standard Optional Tektronix part number

WFM5200 Waveform Monitor Product D ocumentation Kit

This kit co

ntains this printed manual (071-2887-XX) and a CD

(063-4341-XX) containing various user documents. (See page 3,

Documentation.)

020-3075-XX

One EMI suppression ferrite core. Attach to the power cord to reduce

electrom

agnetic interference. Impedance 240 Ω at 100 MHz.

276-0346-00

EMI supp

ression ferrite core installation instructions show how to attach

the ferrite core to the power cord.

071-2706-XX

One VGA (female) to DVI (male) display adapter to connect an external

monitor to the instrument.

013-03

47-00

One 75 Ω terminator for use on the rear-panel connectors. The EXT REF

conne

ctor requires termination when in use.

011-0163-00

WFM50

F01, portable cabinet with handle, feet, tilt bail, and front-panel

cover.

WFM50F01

WFMRACK-NN accommodates two WFM8xxx, WFM7xxx, or WFM6xxx.

Also includes two short depth adaptors to accommodate two WFM5xxx or

WFM4

000.

WFMRACK-NN

WFM

RACK-ON accommodates one older unit (1700 Series, WFM601, or

764 and one new unit, such as the W F M 8xxx, WFM7xx x, or WFM 6xxx.

Also includes one short depth adapter (only usable in NEW Sleeve) for

th

e WFM5xxx or WFM4000.

WFM

RACK-ON

Po

wer Cord

NOTE. See the International Power C ords list that follows this table for

the type of power cord included with your instrument.

Not applicable

2 WFM5200 Installation and Safety Instructions

Preface

International

power cords. Your instrument was shipped with one o f the following

power cord options. Power cords for use in North America are UL listed and CSA

certiﬁed. Cords for use in areas other than North America are approved by at least

one authority acceptable in the country to which the product is shipped.

Opt. A0 – North America power

Opt. A1 – Universal EUR power

Opt. A2 – United Kingdom power

Opt. A3 – Australia power

Opt. A5 – Switzerland power

Opt. A6 – Japan power

Opt. A10 – China power

Opt. A11 – India power

Opt. A12 – Brazil power

Opt. A99

1

– No power cord or AC adapter

1

When ordering the A99 option, it is the responsibility of the end user to be sure that a certiﬁed power cord, for the

country or region it is installed, is used with this instrument.

CAUTION. To reduce risk of ﬁre and shock, use the certiﬁed power cord provided

with the product.

Documentation

The following table lists some of the documentation that is available for this

product and shows where you can ﬁnd it: in a printed manual, on the product

documentation CD-ROM, or on the Tektronix Web site at www.tektronix.com.

Table 1: Product documentation

Item Purpose Location

Installation and Safety Instructions

(this manual)

Provides safety and compliance information with

hardware installation instructions to present the

associated safety warnings. This manual is available

in English, Japanese, and Simpliﬁed Chinese.

Printed manual and also

available in electronic format

at www.tektronix.com/manuals

User Manual

Provides operation and application information. This

manual is available in English.

Product Documentation

CD and available at

www.tektronix.com/manuals

Online Help

In-depth instrument operation and UI help.

On the instrument

System Integration Technical

Reference

Provides information for system integrators designing

systems for HD, SD, and 3 Gb/s SDI video content

where these instruments are being deployed.

Product Documentation

CD and available at

www.tektronix.com/manuals

WFM5200 Installation and Safety Instructions 3

Preface

Table 1: Product documentation, (cont.)

Item Purpose Location

Speciﬁcations and Performance

Veriﬁcation Technical Reference

Speciﬁcations and procedures for checking instrument

performance.

Product Documentation

CD and available at

www.tektronix.com/manuals

WFM and WVR Series

Management Information

Database (MIB) Programmer

Manual

SNMP command reference for remotely controlling the

instrument.

Product Documentation

CD and available at

www.tektronix.com/manuals

Service Manual Provides information about adjustments, repair, and

replaceable parts.

Available at

www.tektronix.com/manuals

Release Notes

Provides information about the key features and known

limitations of a speciﬁc software version release.

Available at

www.tektronix.com/manuals

4 WFM5200 Installation and Safety Instructions

General Safety Summary

General Safet

ySummary

Review the fo

llowing safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedures.

To Avoid Fire or Personal

Injury

Use Proper Power Cord. Use only the power cord speciﬁed for this product and

certiﬁed for the country of use.

Ground the Product.. This product is grounded through the grounding conductor

of the power cord. To avoid electric shock, the grounding conductor must be

connected to earth ground. Before making connections to the input or output

terminals of the product, ensure that the product is properly grounded.

Observe All Terminal Ratings. To avoid ﬁre or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, that

exceeds the maximum rating of that terminal.

Power Disconnect.. The power cord disconnects the product from the power

source. Do not block the power cord; it must remain accessible to the user at

all times.

Do Not Operate Without Covers. Do not operate this product with covers or

panels removed.

Do Not Operate With Suspected Failures. If you suspect that there is damage to

this product, have it inspected by qualiﬁed service personnel.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Use Proper AC Adapter. Use only the AC adapter speciﬁed for this p roduct.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation. Refer to the manual's installation instructions for

details on installing the product so it has proper ventilation.

WFM5200 Installation and Safety Instructions 5

General Safety Summary

TermsinthisManual

These terms may

appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

Symbols and Terms on the

Product

These terms may appear on the product:

DANGER in

dicates an injury hazard immediately accessible as you read

the marking.

WAR N I N G

indicates an injury haza rd not immediately a ccessible as you

read the marking.

CAUTIO

N indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

6 WFM5200 Installation and Safety Instructions

Compliance Information

Compliance In

formation

This section

lists the EMC (electromagnetic compliance), safety, and

environmental standards with which the instrument complies.

EMC Compliance

EC Declaration of

Conformity – EMC

Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.

Compliance was demonstrated to the following speciﬁcations as listed in the

Ofﬁcial Journal of the European Communities:

EN 55103:1996. Product family standard for audio, video, audio-visual and

entertainment lighting control apparatus for professional use.

1

,

2

Environment E2 – commercial and light industrial

Part 1 Emission

EN 55022:1987. Class B radiated and conducted emissions

EN 55103-1:1996 Annex A. Radiated magnetic ﬁeld emissions

Part 2 Immunity

IEC 61000-4-2:2001. Electrostatic discharge immunity

IEC 61000-4-3:2006. RF electromagnetic ﬁ eld immunity

IEC 61000-4-4:2004. Electrical fast transient / burst immunity

IEC 61000-4-5:2005. Power line surge immunity

IEC 61000-4-6:2003. Conducted R F Immunity

IEC 61000-4-11:2004. Voltage dips and interruptions immunity

EN 55103-2:1996 Annex A Radiated magnetic ﬁeld immunity

EN 55103-2:1996 Annex B Balanced ports common mode immunity

1

For compliance with the EMC standards listed here, high-quality shielded interface cables should be used.

2

Inrush current: 8 A peak.

EN 61000-3-2:2006. AC power line harmonic emissions

EN 61000-3-3:1995. Voltage changes, ﬂuctuations, and ﬂicker

European Contact.

Tektronix UK, Ltd.

Western Peninsula

Western Road

Bracknell, RG12 1RF, United Kingdom

WFM5200 Installation and Safety Instructions 7

Compliance Information

Australia / New Zealand

Declaration of

Conformity – EMC

Complies with t

he EMC provision of the Radiocommunications Act per the

following standard, in a ccordance with ACMA:

EN 55022:1987

. Radiated and conducted emissions, Class B, in accordance

with EN 55103-1:1996.

Environmental considerations

This section provides information about the environmental impact of the product.

Product end-of-life

handling

Observe the following guidelines when recycling an instrument or component:

Equipment recycling.

Production of this equipment r equired the extraction and use of natural resources.

The equi

pment may contain substances that could be harmful to the environment

or human health if improperly handled at the product’s end of life. In order to avoid

release of such substances into the environment and to reduce the use of natural

resources, we encourage you to recycle this product in an appropriate system that

will ensure that most of the materials are reused or recycled appropriately.

This symbol indicates that this product complies with the applicable European

Union

requirements according to Directives 2002/96/E C and 2006/66/EC

on waste electrical and electronic equipment (WEEE) and batteries. For

information about recycling options, check the S upport/Service section of the

Tek tr

onix Web site (www.tektronix.com).

Perchlorate materials. This product contains one or more type CR lithium

batteries. According to the state of California, CR lithium batteries are

cla

ssiﬁed as perchlorate materials and require special handling. See

www.dtsc.ca.gov/hazardouswaste/perchlorate for additional information.

Restriction of hazardous

su

bstances

This product is classiﬁed as an industrial monitoring and control instrument,

an

d is not required to comply with the substance restrictions of the recast RoHS

Directive 2011/65/EU until July 22, 2017.

8 WFM5200 Installation and Safety Instructions

Operating Requirements

Operating Req

uirements

This section

provides the speciﬁcations that you need to know to operate your

product safely and correctly. Refer to the complete product speciﬁcations for

additional information.

Electrical Ratings

Power Requ irements

Power connector

NOTE. If you ordered a power cord, it will come with a ferrite core. Install the

ferrite core as shown in the instructions with which it was shipped.

The instrument operates from an external AC adapter and has the following power

requirements:

A single-phase power source with one current-carrying conductor at or near

earth-ground (the neutral conductor).

The power source frequency must be 50 or 60 Hz, and a operating voltage

range m ust be from 100 to 240 VAC, continuous.

WAR

NING. To re duce risk of ﬁre and shock, make sure the mains supply voltage

ﬂuctuations do not exceed 10% of the operating voltage range.

Sy

stems with both current-carrying conductors live with respect to ground

(such as phase-to-phase in multiphase systems) are not recommended as

power sources.

NOTE. Only the line conductor is fused for over-current protection. The fuse is

internal and not user replaceable. Do not attempt to replace the fuse. If you

suspect the fuse has blown, return the unit to an authorized service center for

repair.

WFM5200 Installation and Safety Instructions 9

Operating Requirements

Battery Power

This instrumen

t can be powered by a 12 V DC input or by a 14.4 V standard

camera battery. If you are using a battery with this instrument, read the following

battery safety notices. This instrument was designed to be used with an Anton

Bauer battery. It can also be used with a Sony or IDX V-mount style battery.

CAUTION. Before using the Anton Bauer Power Tap feature, refer to the product

information included with the battery. If that information is not available, contact

the battery

manufacturer for information.

WARNING. Fire can cause personal injury and/or property damage. To prevent

risk of ﬁr

e, when using a 12 V DC source other than the provided AC adapter,

make sure that it has a suitable current limiting device (such as a fuse).

WARNING

. Risk of personal injury and/or property damage from falling

instrument. Batteries from various manufacturers may vary in shape and weight.

When a battery is installed, it is possible that it will make the unit too heavy in the

back, causing the instrument to tip backward.

Environmental Ratings

Table 2: Environmental performance

Category Standards or description

Operating 0 °C to +40 °C

Temperature

Non Operating –20 °C to +60 °C

Operating 20% to 80% relative humidity relative humidity at up to +40 °C, noncondensing

Humidity

Non Operating below 5% or above 90% RH (relative humidity) at up to +60 °C, noncondensing

Operating Up to 9,842 feet (3,000 meters)

Altitude

Non Operating Up to 40,000 feet (12,192 meters)

The variable fans provide forced air circulation. Do not block ventilation openings.

Bare

Instrument

(no optional

sleeves)

To allow for proper airﬂow, there must be at least 2 inches of clearance on both sides of

the instrument, at least 2 inches of clearance from the rear of the instrument, and at least a

1/2 inch of clearance from the top of the instrument.

Portable

Cabinet

Use only the Tektronix portable cabinet, WFMF02, to allow for proper airﬂow with this

instrument. When using the portable c abinet, the same minimum clearances as the Bare

Instrument apply.

Cooling

Rack Cabinet Use only the WFMRACK-NN or WFMRACK-ON rackmount rack adapter for this instrument. To

allow for proper airﬂow when installing the rack adapter in a closed rack with solid walls, there

must be at least 2 inches of clearance from both sides of the rack adapter frame to the rack side

walls, at least 3 inches of clearance from the rear of the rack adapter frame to the back wall of

the rack, and at least a 1/2 inch of clearance from the top of the rack adapter to another rack

adapter or installed instrument. The rack intake air to the side vents must not exceed 40 °C.

10 WFM5200 Installation and Safety Instructions

Operating Requirements

Physical Spec

iﬁcations

Table 3: Physical characteristics

Characteris

tic

Standard

Height

5.25 inches (

133.4 millimeters)

Width

8.5 inches (

215.9 millimeters)

Dimensions

Depth

4.75 inche

s (120.7 millimeters)

Net

3.3 pounds

(1.5 kilograms)

Weight

Shipping 12 pounds

(5.4 kilograms), approximate, excluding options and accessories

Cleaning

Not requ

ired for the safe operation of the instrument. However, if you wish to

perform routine cleaning on the exterior of the instrument, refer to the user manual

on the Product Documentation CD that was shipped with your instrument.

WFM5200 Installation and Safety Instructions 11

Rear-Panel Connectors

Rear-Panel Co

nnectors

The followin

g ﬁgure shows the rear-panel. The SDI inputs are arranged

horizontally and the external reference connectors are arranged vertically.

Rear-panel

Input and Output Connectors

Video Connectors

SDI inputs are self-terminating inputs.

Input

Connector

REF Loop. A synchronization input. The input signal can be

analog black burst, analog composite v ideo, or analog tri-level

for HD. Requires termination.

NOTE. The reference input is a passive loop input, so external

termination is required.

SDI 1A. The digital A c omponent serial digital input.

SD

I1B.The digital B component serial digital input.

SDI 2A. The digital A c omponent serial digital input.

SDI 2B. The digital B c omponent serial digital input.

12 WFM5200 Installation and Safety Instructions

Rear-Panel Connectors

Output Connector

SDI Out. Select to output Loop Out or Test S ignals (with Option

GEN installed) for SD-SDI, HD-S DI, or 3G-SDI (Level A or level

B)

1

.

1

3G-SDI Test Signals are available with Option 3G installed.

EXT DISPLAY C

onnector

Pin Assignment

This is the external display monitor output. The display resolution is 1024 x

768. The output supports DVI monitors directly and analog PC (RGB) monitors

with the use of a DVI-I to VGA adapter. The EXT DISPLAY connector is a

DVI-I conn

ector with socket contacts.

EXT DISPLAY connector

REMOTE C

onnector Pin

Assignment

The REMOTE connector interface uses ground closures for remote control and

indicating to external equipment when alarms have occurred. The input of LTC is

through the REMOTE connector. The REMOTE connector is a 15-pin D-type

connec

tor with socket contacts

NOTE. For more information on Preset recall, refer to the user manual on the

Product Documentation CD that was shipped with your instrument.

WFM5200 Installation and Safety Instructions 13

Rear-Panel Connectors

Remote connect

or preset functions.

Characteristic Pin out Preset functions

Connector Pin Assignments

Hex Binary

Pins 15,

14, 13,

12, 11,

10

Direct

mode

selection

Encoded

mode

selection

F 111111

none

No action

E XX1110 Preset 1 No action

D XX1101 Preset 2 No action

C

XX1100

SDI B

B XX1011 Preset 3

SDI A

A XX1010 No action

9 XX1001 No action

8 XX1000 Preset 8

7

XX0111 Preset 4 Preset 7

6 XX0110 Preset 6

5

XX0101 Preset 5

4 XX0100 Preset

4

3 XX0011 Preset 3

2 XX0010 Preset 2

1 XX000

1

Prese

t1

0 XX0000 Unused

N/A

101111 Preset 5

N/A

1GND(In)

2 Reserved (I/O)

3 Reserved (I

/O)

4 R eserved (In)

5 R eserved (In)

6GND(In)

7 Time Code Positive (LTC In)

8 Time C ode Negative (LTC In)

9 Ground Cl

osure (Alarm Out)

10 Preset 1 (In)

11 Preset 2 (In)

12 Preset

3(In)

13 Preset 4 (In)

14 Preset 5 (In)

15 Prese

t6(In)

N/A

011111 Preset 6

N/A

Ethernet Connector

The instrument provides a 10/100/1000 BaseT Ethernet interface. The Ethernet

connector is a standard RJ-45 connector.

E

thernet connector

14 WFM5200 Installation and Safety Instructions

ページを読み込んでいます...

Tektronix WFM5200 series, WVR5200 Series Instructions Manual

関連論文

その他の書類