5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
Support
Support
workmanship for a period of ve (5) years from the date of delivery provided that the
Product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional stas are
ready to solve your problems at any time Korenix global service center's e-mail is
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 2302 on
the DIN rail. For information about the DIN Rail installation, please
refer to user’s manual.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent the DC wires from being loosened.
3. Both of the redundant power inputs accept negative or positive type power source; the
negative power source is commonly used in telecom applications. See the gure-1 and gure-2
for the power wiring.
Note: e recommended working voltage is DC24V (DC10~ 60V); both power inputs
should apply with the same power system; either positive or negative.
Wiring the Relay Output and Chassis Grounding
e relay output alarm contacts are in the middle of the terminal block connector as shown in
the gure below.
By inserting the wires and setting the DIP switch of the respective Port Alarm to “ON”, relay
output alarm will detect any port failure and form a short circuit. e alarm relay output is
“Normal Open”. Please refer to Figure -3 for the relay wiring architecture.
Operating Mode Selection
e JetCon 2302 is not only a 4-port Switch, but it is also a 2-channel Fast Ethernet Media
Converter. It is congured by the DIP switch and activated through the power resetting or the
reset button. To understand the functions of the Switching and converter modes, refer to the
table below:
In an industrial environment there might be
a lot of devices that generate electromagnetic
noise, such as AC motors, electric welding
machines and power generators. ese
devices will generate electric noise or surges
that might disturb communication. To
prevent these interferences, the JetCon 2302
should be well earthed.
Connecting to Network
1. Connecting the Ethernet Port: Connect the Ethernet RJ-45 port to another networking
device by properly twisted cable (UTP or STP). If the port is well linked with partner, the
Link LED (Green) will turn on and the Activity LED will start blinking slowly when the
packets are transmitting and receiving. e RJ-45 ports support MDI/MDI-X function.
2. Connecting the Fiber Port: Connect the ber port to ber link partner by proper ber
cable as shown in the Figure-4. Ensure that both of connected ber ports are the same type
and use exactly optical ber cable.
!
is is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
DIP Switch Setting
Package Check List
JetCon 2302 Industrial Media Converter
Quick Installation Guide
JetCon 2302 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.3
JetCon 2302 is a Fast Ethernet to Fiber Media Converter with 2 Fast Ethernet copper and 2
ber ports allowing the device to act as 4 port Fast Ethernet Fiber switch or 2-channel
Converter for exible industrial applications. In switch mode, JetCon 2302 is an industrial
4-port 10/100Mbps Fast Ethernet Switch, incorporating 3.2Gbps switching fabric with
non-blocking store and forward technology to fulll the high transmission performance
requirements. In converter mode, JetCon 2302 is a cost eective industrial 2-channel
10/100TX to 100FX media converter with an error packet ltering function. It also provides
relay alarm output function for the port and power alert. e heavy industrial EMC compliant
JetCon 2302, designed with IP31 grade enclosure, is equipped with dual redundant
DC10~60V power inputs and provides 1.5KV Hi-Pot isolation protection and wide operating
temperature, therefore ensuring highly reliable network performance under harsh industrial
environments with vibration and shock.
Overview
A Beijer Electronics Group Company
Figure -3
Converter mode
No.
Port 1, 3 grouped as a single channel A
Port 2, 4 grouped as a single channel B
Store and forward
Fully supported
Switching mode
Yes
Store and forward
Fully supported
Data exchange
Forward Technology
Port Event Alarm
Description
Port link down event alarm enabled.
Port link down event alarm disabled. (Default)
Enabled Converter mode
Switch mode. (Default)
Enabled power event alarm
Disabled power event alarm (Default)
Status
ON
Off
ON
Off
ON
Off
Not avaliable
Pin No. #
DIP 1~4
DIP 5
DIP 6
DIP 7
DIP Switch Setting
Description
Green on: the port is linked well with partner
Green blinking: the port is transmitting packet.
Green on: the port is linked well with partner.
Green blinking: the port is transmitting packet.
Green on: the power is on applying.
Red on: port link down or power off event occurred, and the
alarm relay output conductors formed a short circuit.
Green on: the device is setting on the converter mode.
LED color
Green
Yellow
Green
Yellow
Green
Red
Green
Indicators
Ethernet
RJ-45
Fiber
PWR 1,2
Con.
Alm
Package Check List
JetCon 2301 Industrial Media Converter
Quick Installation Guide
A Beijer Electronics Group Company
JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.1
JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of
forwarding modes – Store and Forward, Modied Cut-through, Pure Converter and
Converter with auto-change modes. e JetCon 2301 adopts rugged aluminum case with
IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh
environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or
-40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes
for alerting remote or central management systems when a remote fault occurs. It also
adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be
enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range
DC10~60V through the 6-pin removable terminal block. e ber port supports
Single-mode or Multi-mode for providing up to 30KM extended distance transmission.
Overview
Package Check List
JetCon 2302 Industrial Media Converter
Quick Installation Guide
JetCon 2302 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.3
JetCon 2302 is a Fast Ethernet to Fiber Media Converter with 2 Fast Ethernet copper and 2
ber ports allowing the device to act as 4 port Fast Ethernet Fiber switch or 2-channel
Converter for exible industrial applications. In switch mode, JetCon 2302 is an industrial
4-port 10/100Mbps Fast Ethernet Switch, incorporating 3.2Gbps switching fabric with
non-blocking store and forward technology to fulll the high transmission performance
requirements. In converter mode, JetCon 2302 is a cost eective industrial 2-channel
10/100TX to 100FX media converter with an error packet ltering function. It also provides
relay alarm output function for the port and power alert. e heavy industrial EMC compliant
JetCon 2302, designed with IP31 grade enclosure, is equipped with dual redundant
DC10~60V power inputs and provides 1.5KV Hi-Pot isolation protection and wide operating
temperature, therefore ensuring highly reliable network performance under harsh industrial
environments with vibration and shock.
Overview
A Beijer Electronics Group Company