Sony SS-X500A 取扱説明書

Speaker System

Operating Instructions Page 2

Mode d’emploi Page 16

Bedienungsanleitung Seite 30

Manual de instrucciones Página 46

Istruzioni per l’uso Pagina 60

74

 1998 by Sony Corporation

SS-X500A

3-864-740-03(1)

English
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

3

English

Table of Contents

Features .....................................................................3

Precautions................................................................4

Parts List....................................................................5

Parts Identification....................................................6

Installing the Speakers .............................................7

Installing the Speakers on a Wall......................9

Changing the Speaker Angles .........................10

Attaching the Ferrite Filters ...................................11

Connecting to the Monitor .....................................12

Connecting to the Amplifier ...................................14

Specifications..........................................................15

EN

Features

The SS-X500A is a two-way bass reflex speaker system

which adopts a cone-type woofer and tweeter. This speaker

system is designed for use with the PFM-500A1WU/A1WE

flat panel monitor. The metal mesh grill has been designed

to improve the quality of the sound. You can enjoy the high

quality stereo sound.

4

Operating and storage locations

Avoid operating or storing the product in the following

locations.

• Extremely hot or cold places

• In direct sunlight for long periods, or close to heating

equipment

• Damp or dusty places

• Where it is exposed to rain

• Locations subject to strong vibration

Care

• Clean the cabinet with a soft, dry cloth. If it is very dirty,

use a cloth dampened with a small quantity of neutral

detergent, then wipe dry.

• Avoid the use of volatile solvents such as alcohol, benzene,

and thinners. They may damage the surface finish, or

impair the operation of the shutter adaptor.

Ventilation

Do not wrap the unit in a cloth, etc., during operation. This

may cause the internal temperature to rise excessively and

the unit to malfunction.

Miscellaneous

• Be careful not to spill water or other liquids on the unit or

allow combustible or metallic objects inside the body. If

used with foreign objects inside, the unit is liable to fail or

cause a fire or an electric shock.

• If the product is transported or shipped, repack it as

originally packed at the factory, or in materials equal in

quality.

• Avoid driving the speaker system continuously with an

input exceeding the maximum input power of this speaker

system.

• Before connecting, turn off the amplifier to avoid

damaging the speaker system.

• If the +/– connection is incorrect, the bass tones seem to be

missing and the position of the instruments becomes

obscure.

In the event of any problems with the operation of the unit,

contact your Sony service representative.

Precautions

5

Parts List

Speaker (2)

Bracket (2)

Speaker attachment screw

(black, M5×9) (6)

Speaker cord 2.5 m (2)

Bracket attachment screw

(gray, M4×14) (8)

Speaker cord holder (4)

R

L

Ferrite filter (4)

6

Parts Identification

Tweeter

Speaker Rear

Woofer

Speaker Front

Angle lock

screw

Bracket

attachment

holes

Bracket

Woofer

Wall

attachment

holes

Angle lock

screw

Speaker

attachment

holes

R

L

Speaker

attachment

holes

RL

Wall

attachment

hole

Wall

attachment

hole

7

Installing the Speakers

Right Speaker

Left Speaker

Panel cover

screws

Brackets

Bracket

attachment

screws

Install the right/left speakers using the brackets as follows:

1 Match the speaker attachment holes on the speaker to

the speaker attachment holes on the bracket. Attach the

brackets to the speakers with the supplied M5 screws

(black, 3 screws each for left and right holes).

Assemble the left speaker by matching the L-mark of

the speaker to the L-mark of the bracket. (The L-marks

must be aligned side by side.)

Similarly, you can install the right speaker by matching

the R-mark of the speaker to the R-mark of the bracket.

(The R-marks must be aligned side by side.)

2 Loosen the panel cover screws (2 each for right and

left). Open the panel cover.

There are 4 bracket attachment holes to install the

speakers.

3 Insert the supplied M4 screws (gray, 4 screws each for

right and left) into the bracket attachment holes and

temporarily tighten them.

Bracket

attachment

holes

RL R

L

RL

R

L

RL

R

L

Speaker

attachment

holes

The L-marks must be

aligned side by side.

8

Monitor

Speaker

4 Hook the bracket attachment holes on the bracket onto

the screws temporarily tightened in Step 3. Install the

speakers.

5 Tighten the screws completely with a coin and lock the

speakers.

6 Connect the speaker to the monitor with the supplied

cord.

For more details, see “Connecting to the Monitor” on

page 12.

7 Close the panel cover and tighten the panel cover

screws (2 screws each for right and left.)

To remove the speakers

Reverse the installation process.

Note

Only use the supplied screws when installing the speakers.

Installing the Speakers

R

9

You can install the speakers on a wall using the wall

attachment screw holes of the brackets and speakers.

You can change the speaker angles if you have installed the

speakers with the brackets.

Installing the Speakers on a Wall

Wall attachment holes (

φ

6 mm)

When you use a bracket

R

L

When you do not use a bracket

552 mm

(

21

3

/

4

inches

)

Wall attachment holes

10

PFM-500A1WU/A1WE Front

After installing the speakers on the monitor, you can change

the speaker angle.

To move the speakers far forward, follow the steps below:

1 Loosen the M5 screws (black, 3 screws each for right

and left that fix the speakers and the brackets). Slide out

the speaker.

When fixing the speaker angle, check the scale on the

speaker to fix it evenly.

As the speakers slide out, the speakers move more

toward the front.

2 Move the speakers to change the speaker angle.

3 To lock the speaker angle, tighten the angle lock screw

by hand or with a hexagon wrench.

Note

Do not turn the speaker with excessive force after tightening

the angle lock screw.

Changing the Speaker Angles

When turning for forward

Installing the Speakers

Angle lock screw

RL

R

L

RL

R

L

R

RL

L

11

Attaching the Ferrite Filters

Wrap the speaker cable around the supplied filters four

times to hold them in place.

Speaker cord

Tip of the speaker cord

Approx. 5 cm

(2 inches)

to speaker terminal on the

PFM-500A1WU/A1WE

flat panel monitor

to speaker terminal on the

SS-X500A speaker system

Approx. 5 cm

(2 inches)Ferrite filters

12

SPEAKERS

(6-16 Ω)

+

L

–

+

R

–

Connecting to the Monitor

Before connecting the speakers to the monitor, be

sure to turn off the monitor’s power.

Connect the speakers to the monitor while the panel cover

on the monitor is open.

For details on how to install the speakers to the monitor, see

“Installing the Speakers” on page 7.

1 Connect the speaker cords to the monitor speaker

terminals.

Make sure the R (Right) speaker and L (Left) speaker

are connected to the R (Right) terminals and L (Left)

terminals on the monitor respectively.

Match the polarity of the speaker terminals with the

polarity of the speaker terminals on the monitor, ‘ to

‘ with the red cord and ’ to ’ with black cord.

2 Connect the speaker cords to the speakers.

Make sure to connect the R (Right) cord to the right

speaker and the L (Left) cord to the left speaker.

When you connect the cord to the right speaker, pull out

the cord from under the monitor panel cover and lay it

under the monitor to the right speaker.

Use the supplied speaker cord holders to tuck the cord.

For details on how to attach the speaker cord holder,

see “To install the speaker cord holders” on next page.

Similarly, when you connect the cord to the left speaker,

pull out the cord from under the monitor panel cover

and lay it under the monitor to the left speaker.

Tuck any excess cord inside the panel cover.

3 Close the right and left panel covers.

Red

buttons

Black

buttons

Press the button

and insert the

cord into the

proper terminal.

Pull the cord

slightly to make

sure it is

connected firmly.

Red

cord

Black cords

Red

cord

Right

speaker

Left

speaker

Speaker cord holders

13

2 cm

To install the speaker cord holders

As shown in the figure, insert the holders into the holes on

the ventilation openings.

Evenly space the holders and insert them under the monitor

cover.

If you use an optional mounting bracket, the bracket

position and the holder positions should not overlap.

Securely insert the

holders into the holes

on the ventilation

openings.

Monitor cover

To use an optional

mounting bracket,

insert the holders

where the brackets are

not installed. See the

figure.

Notes

• Be careful not to short-circuit the speaker terminals

according to the wire sticking out of the insulation.

• Connect the speaker cords with correct polarity. Correct

‘’ connections of both speaker systems insures proper

inphase operation. If the speaker system is out-of-phase,

the bass tones seem to be missing and the position of the

sound sources become obscure.

• Do not connect the speakers to both an amplifier and a

monitor at the same time. Otherwise, the excessive electric

current may flow from the amplifier to the monitor via the

speaker cord, which may damage the monitor.

(

13

/16 inches)

14

Connect the cord to the speaker terminals of the AV

amplifier.

Notes

• The amplifier output must be 120W or less.

• Do not connect the speaker system to the monitor and an

amplifier. Doing so may cause a large amount of current

to flow into the monitor from the amplifier via the speaker

cord, resulting in damage to the monitor.

Connecting to the Amplifier

AV amplifier

Right speaker

Left speaker

RL RL

15

Speaker system

Woofer × 2, magnetically shielded

Tweeter × 1, magnetically shielded

Speaker unit 8 cm (3

1

/4 inches), cone type

2.5 cm (1 inch), dome type

Enclosure type

Bass reflex

Rated impedance

8 ohms

Power handling capacity

Maximum input power: 120 W

Characteristic sensitivity level

88 dB (1 W, 1 m)

Effective frequency range

70 Hz to 20,000 Hz

Operating conditions

Temperature 0°C to +35°C (32°F to 95°F)

Humidity 0% to +90% (no condensation)

Pressure 700 hPa to 1,060 hPa

Transport and storage conditions

Temperature –10°C to +40°C (14°F to

104°F)

Humidity 0% to +90% (no condensation)

Pressure 700 hPa to 1,060 hPa

Dimensions Approx. 159 × 634 × 90 mm (6

3

/8 × 25 ×

3

5

/8 inches) (w/h/d), including front grille

(net per speaker)

Specifications

Mass Approx. 3.5 kg (7 lb 11 oz) (net per speaker)

Approx. 1.1 kg (2 lb 7 oz) (net per bracket)

Supplied accessories

Speaker cord (2, 2.5 m)

Speaker attachment screw (6)

Bracket attachment screw (8)

Speaker cord holder (4)

Ferrite filter (4)

Operating instructions (1)

Design and specifications are subject to change without

notice.

Characteristic curves

20 50

100 200 500 1K 2K 5K 10K 20K 50K

0

100

90

80

70

60

50

40

30

20

10

8

Frequency in Hz

Frequency response

Impedance

Sound Pressure Level in dB

Impedance in ohms

Français

AVERTISSEMENT

Afin d’eviter tout risque d’incendie ou

d’électrocution, ne pas exposer cet

appareil à la pluie ou à l’humidité.

17

Français

Table des matières

Caractéristiques ......................................................17

Précautions..............................................................18

Liste des composants ............................................19

Identification des composants ..............................20

Installation des haut-parleurs ................................21

Installation des haut-parleurs au mur ..............23

Changement de l’angle des haut-parleurs .......24

Installation des filtres en ferrite.............................25

Raccordement au moniteur....................................26

Raccordement à l’amplificateur.............................28

Spécifications..........................................................29

F

Caractéristiques

Le SS-X500A est un système de haut-parleurs bass reflex à

deux voies intégrant un woofer et un tweeter en cône. Ce

système de haut-parleurs est conçu en vue d’une utilisation

avec un moniteur à écran plat PFM-500A1WU/A1WE. La

grille métallique a été étudiée pour permettre une

optimisation de la qualité sonore. Vous pouvez de ce fait

pleinement exploiter une haute qualité sonore stéréo.

18

Lieu d’utilisation et de stockage

Evitez d’utiliser ou de stocker l’unité dans des endroits :

• extrêmement chauds ou froids;

• soumis au rayonnement direct du soleil durant de longues

périodes ou à proximité d’un système de chauffage;

• humides ou poussiéreux;

• exposés à la pluie;

• soumis à de fortes vibrations;

Entretien

• Nettoyez le châssis avec un chiffon doux et sec. S’il est

fortement souillé, utilisez un chiffon légèrement imprégné

d’une solution détergente neutre et essuyez-le ensuite.

• N’utilisez pas de solvants volatiles comme de l’alcool, du

benzène ou des diluants. Ils risquent de ternir le fini du

châssis ou de perturber le bon fonctionnement de

l’adaptateur d’obturation.

Ventilation

N’enveloppez pas l’unité dans du tissu, etc., en cours de

fonctionnement. Cela risque d’entraîner une augmentation

excessive de la température intérieure et un

dysfonctionnement de l’unité.

Divers

• Veillez à ne pas répandre d’eau ou un autre liquide sur

l’unité; prévenez toute pénétration éventuelle de matériaux

combustibles ou métalliques dans le châssis. En cas de

pénétration d’un corps étranger à l’intérieur du châssis,

l’unité est susceptible de tomber en panne, de prendre feu

ou de provoquer une électrocution.

• Si l’unité doit être transportée ou expédiée, remballez-la

dans son conditionnement d’origine ou dans des matériaux

de qualité équivalente.

• Evitez de faire fonctionner les enceintes de manière

continue avec une entrée qui excède la puissance d’entrée

maximum de ce système.

• Avant d’effectuer les connexions, mettez l’amplificateur

hors tension pour éviter d’endommager les enceintes.

• Si les bornes +/– ne sont pas raccordées correctement, les

tonalités basses sembleront absentes et la position des

instruments sera confuse.

Si vous rencontrez des problèmes d’utilisation avec cet

appareil, consultez un représentant du service après-vente

Sony.

Précautions

19

Liste des composants

Haut-parleur (2)

Support (2) Vis de fixation de haut-parleur

(noir, M5×9) (6)

Cordon de haut-parleur

(2,5 m) (2)

Vis de fixation de support

(gris, M4×14) (8)

Crochet à cordon de

haut-parleur (4)

R

L

Filtre en ferrite (4)

20

Identification des composants

Tweeter

Support

Woofer

Haut-parleur

avant

Vis de réglage

d’angle

Orifices de

fixation de

support

Woofer

Orifice de

fixation

murale

Orifice de

fixation

murale

RL

R

L

Orifices de

fixation de

haut-parleur

Orifices de

fixation de

haut-parleur

Orifice de

fixation

murale

Haut-parleur

arrièr

Vis de réglage

d’angle

ページを読み込んでいます...

Sony SS-X500A 取扱説明書

関連論文

その他の書類