DeWalt DWE7492 ユーザーマニュアル

ブランド: DeWalt

モデル: DWE7492

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

DWE7492

Final Page size: A5 (148mm x 210mm)

English 7

简体中文 21

Fig. B

图 B

Fig. A

图 A

8 7 6

1116

Fig. C

图 C

Fig. E

图 E

Fig. D

图 D

5213

Fig. F

图 F

Fig. G

图 G

Fig. H

图 H

Fig. L

图 L

Fig. K

图 K

Fig. J

图 J

Fig. I

图 I

34 33

Position 1

位置 1

Position 2

位置 2

Fig. M

图 M

Fig. P

图 P

Fig. Q

图 Q

Fig. O

图 O

Fig. N

图 N

Fig. R

图 R

Fig. S

图 S

Fig. V

图 V

Fig. T

图 T

Fig. U

图 U

Fig. X

图 X

Fig. W

图 W

Fig. AA

图 AA

Fig. Y

图 Y

Fig. Z

图 Z

Lorem ipsum

ENGLISH

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough

product development and innovation make DeWALT one of the

most reliable partners for professional power toolusers.

Technical Data

DWE7492

Voltage V

220-240

Motor power (input) W 2000

Motor power (output) W 1200

No load speed min

-1

4800

Blade diameter mm 254

Blade bore mm 25.4

Blade body thickness mm 2.0

Riving knife thickness mm 2.2

Depth of cut at 90° mm 79

Depth of cut at 45° mm 57

Bevel angle º 45–90

Maximum bevel angle º 45–90

Mitre angle º 30–90

Ripping capacity mm 825

Overall dimensions mm 680 x 650 x 330

Weight

kg 26.5

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

General Power Tool Safety Warnings



WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

English (original instructions)

TABLE SAW

DWE7492

ENGLISH

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

Safety Instructions for Table Saws

1) Guarding Related Warnings

a ) Keep guards in place. Guards must be in working

order and be properly mounted. A guard that is loose,

damaged, or is not functioning correctly must be repaired

orreplaced.

b ) Always use saw blade guard, riving knife and anti-

kickback pawls for every through-cutting operation.

For through-cutting operations where the saw blade

cuts completely through the thickness of the workpiece,

the guard and other safety devices help reduce the risk

ofinjury.

c ) Immediately reattach the guarding system after

completing an operation (such as rabbeting cuts)

which requires removal of the guard, riving knife

and/or anti-kickback device. The guard, riving knife,

and anti-kickback device help to reduce the risk ofinjury.

d ) Make sure the saw blade is not contacting the guard,

riving knife or the workpiece before the switch is

turned on. Inadvertent contact of these items with the

saw blade could cause a hazardouscondition.

e ) Adjust the riving knife as described in this instruction

manual. Incorrect spacing, positioning and alignment

can make the riving knife ineffective in reducing the

likelihood ofkickback.

f ) For the riving knife and anti-kickback pawls to

work, they must be engaged in the workpiece. The

riving knife and anti-kickback pawls are ineffective when

cutting workpieces that are too short to be engaged with

the riving knife and anti-kickback pawls. Under these

conditions a kickback cannot be prevented by the riving

knife and anti-kickbackpawls.

g ) Use the appropriate saw blade for the riving knife.

For the riving knife to function properly, the saw blade

diameter must match the appropriate riving knife and the

body of the saw blade must be thinner than the thickness

of the riving knife and the cutting width of the saw blade

must be wider than the thickness of the rivingknife.

ENGLISH

2) Cutting Procedures Warnings

a ) DANGER: Never place your fingers or hands

in the vicinity or in line with the saw blade. A

moment of inattention or a slip could direct your

hand towards the saw blade and result in serious

personalinjury.

b ) Feed the workpiece into the saw blade or cutter

only against the direction of rotation. Feeding the

workpiece in the same direction that the saw blade is

rotating above the table may result in the workpiece, and

your hand, being pulled into the sawblade.

c ) Never use the mitre gauge to feed the workpiece

when ripping and do not use the rip fence as a

length stop when cross cutting with the mitre gauge.

Guiding the workpiece with the rip fence and the mitre

gauge at the same time increases the likelihood of saw

blade binding andkickback.

d ) When ripping, always apply the workpiece feeding

force between the fence and the saw blade. Use a

push stick when the distance between the fence and

the saw blade is less than 150 mm, and use a push

block when this distance is less than 50 mm. "Work

helping" devices will keep your hand at a safe distance

from the sawblade.

e ) Use only the push stick provided by the

manufacturer or constructed in accordance with the

instructions. This push stick provides sufficient distance

of the hand from the sawblade.

f ) Never use a damaged or cut push stick. A damaged

push stick may break causing your hand to slip into the

sawblade.

g ) Do not perform any operation "freehand". Always

use either the rip fence or the mitre gauge to

position and guide the workpiece. "Freehand" means

using your hands to support or guide the workpiece, in lieu

of a rip fence or mitre gauge. Freehand sawing leads to

misalignment, binding andkickback.

h ) Never reach around or over a rotating saw blade.

Reaching for a workpiece may lead to accidental contact

with the moving sawblade.

i ) Provide auxiliary workpiece support to the rear

and/or sides of the saw table for long and/or wide

workpieces to keep them level. A long and/or wide

workpiece has a tendency to pivot on the table’s edge,

causing loss of control, saw blade binding andkickback.

j ) Feed workpiece at an even pace. Do not bend or

twist the workpiece. If jamming occurs, turn the

tool off immediately, unplug the tool then clear the

jam. Jamming the saw blade by the workpiece can cause

kickback or stall themotor.

k ) Do not remove pieces of cut-off material while the

saw is running. The material may become trapped

between the fence or inside the saw blade guard and the

saw blade pulling your fingers into the saw blade. Turn

the saw off and wait until the saw blade stops before

removingmaterial.

l ) Use an auxiliary fence in contact with the table top

when ripping workpieces less than 2 mm thick. A

thin workpiece may wedge under the rip fence and create

akickback.

3) Kickback Causes and Related Warnings

Kickback is a sudden reaction of the workpiece due to a pinched,

jammed saw blade or misaligned line of cut in the workpiece with

respect to the saw blade or when a part of the workpiece binds

between the saw blade and the rip fence or other fixedobject.

Most frequently during kickback, the workpiece is lifted from the

table by the rear portion of the saw blade and is propelled towards

theoperator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as givenbelow.

a ) Never stand directly in line with the saw blade.

Always position your body on the same side of

the saw blade as the fence. Kickback may propel the

workpiece at high velocity towards anyone standing in

front and in line with the sawblade.

b ) Never reach over or in back of the saw blade to pull

or to support the workpiece. Accidental contact with

the saw blade may occur or kickback may drag your

fingers into the sawblade.

c ) Never hold and press the workpiece that is being

cut off against the rotating saw blade. Pressing the

workpiece being cut off against the saw blade will create a

binding condition andkickback.

d ) Align the fence to be parallel with the saw blade. A

misaligned fence will pinch the workpiece against the saw

blade and createkickback.

e ) Use a featherboard to guide the workpiece against

the table and fence when making non-through cuts

such as rabbeting cuts. A featherboard helps to control

the workpiece in the event of akickback.

f ) Support large panels to minimise the risk of saw

blade pinching and kickback. Large panels tend to sag

under their own weight. Support(s) must be placed under

all portions of the panel overhanging the tabletop.

g ) Use extra caution when cutting a workpiece that is

twisted, knotted, warped or does not have a straight

edge to guide it with a mitre gauge or along the

fence. A warped, knotted, or twisted workpiece is unstable

and causes misalignment of the kerf with the saw blade,

binding andkickback.

h ) Never cut more than one workpiece, stacked

vertically or horizontally. The saw blade could pick up

one or more pieces and causekickback.

i ) When restarting the saw with the saw blade in the

workpiece, centre the saw blade in the kerf so that

the saw teeth are not engaged in the material. If the

saw blade binds, it may lift up the workpiece and cause

kickback when the saw isrestarted.

ENGLISH

j ) Keep saw blades clean, sharp, and with sufficient

set. Never use warped saw blades or saw blades with

cracked or broken teeth. Sharp and properly set saw

blades minimise binding, stalling andkickback.

4) Table Saw Operating Procedure Warnings

a ) Turn off the table saw and disconnect from the

power source when removing the table insert,

changing the saw blade or making adjustments to

the riving knife, anti-kickback pawls or saw blade

guard, and when the machine is left unattended.

Precautionary measures will avoidaccidents.

b ) Never leave the table saw running unattended.

Turn it off and don’t leave the tool until it comes

to a complete stop. An unattended running saw is an

uncontrolledhazard.

c ) Locate the table saw in a well-lit and level area

where you can maintain good footing and balance.

It should be installed in an area that provides

enough room to easily handle the size of your

workpiece. Cramped, dark areas, and uneven slippery

floors inviteaccidents.

d ) Frequently clean and remove sawdust from under

the saw table and/or the dust collection device.

Accumulated sawdust is combustible and may self-ignite.

e ) The table saw must be secured. A table saw that is not

properly secured may move or tipover.

f ) Remove tools, wood scraps, etc. from the table

before the table saw is turned on. Distraction or a

potential jam can bedangerous.

g ) Always use saw blades with correct size and shape

(diamond versus round) of arbour holes. Saw blades

that do not match the mounting hardware of the saw will

run off-centre, causing loss ofcontrol.

h ) Never use damaged or incorrect saw blade mounting

means such as flanges, saw blade washers, bolts or

nuts. These mounting means were specially designed for

your saw, for safe operation and optimumperformance.

i ) Never stand on the table saw, do not use it as a

stepping stool. Serious injury could occur if the tool is

tipped or if the cutting tool is accidentallycontacted.

j ) Make sure that the saw blade is installed to rotate

in the proper direction. Do not use grinding wheels,

wire brushes, or abrasive wheels on a table saw.

Improper saw blade installation or use of accessories not

recommended may cause seriousinjury.

Additional Safety Rules for Table Saws



WARNING: Cutting plastics, sap coated wood, and other

materials may cause melted material to accumulate on

the blade tips and the body of the saw blade, increasing

the risk of blade overheating and binding whilecutting.

• Avoid awkward positions, where a sudden slip could

cause a hand to move into a sawblade.

• Do not attempt to retrieve materials near the blade on

the saw table while the blade isspinning.

• Never reach in back of, or around, the cutting tool with

either hand to hold down theworkpiece.

• Keep arms, hands and fingers away from the blade to

prevent seriousinjury.

• Use a push stick that is appropriate to the application

to push workpieces through the saw. A push stick is a

wooden or plastic stick, often homemade, that should be used

whenever the size or shape of the workpiece would cause you

to place your hands within 152mm of theblade.

• Use hold-downs, jigs, fixtures or feather boards to help

guide and control the workpiece. Accessories for use with

your tool are available at extra cost from your local dealer or

authorized service centre.

• Do not perform ripping, crosscutting or any other

operationfreehand.

• Never reach around or over sawblade while the blade

isspinning.

• Stability. Make sure the table saw is firmly mounted to a

secure surface before use and does notmove.

• The table saw should only be set up on a level and stable

surface. The work area should be free from obstructions and

trip hazards. No materials or tools should be leaned against

thesaw.

• Never cut metals, cement board or masonry. Certain

man-made materials have special instructions for cutting on

table saws. Follow the manufacturer’s recommendations at all

times. Damage to the saw and personal injury mayresult.

• Do not install a diamond masonry blade and attempt to use

the table saw as a wetsaw.

• The proper throat plate must be locked in place at all

times to reduce the risk of a thrown workpiece and

possibleinjury.

• Wear gloves when handling sawblades.

• Use the correct saw blade for the intended operation.

The blade must rotate toward the front of the saw. Always

tighten the blade arbor nut securely. Before use, inspect the

blade for cracks or missing teeth. Do not use a damaged or

dullblade.

• Never attempt to free a stalled saw blade without first

turning the machine off and disconnect tool from power

source. If a workpiece or cut-off piece becomes trapped inside

the blade guard assembly, turn saw off and wait for blade to

stop before lifting the blade guard assembly and removing

thepiece.

• Never start the machine with the workpiece against

the blade to reduce the risk of a thrown workpiece and

personalinjury.

• Do not have any part of your body in line with the blade.

Personal injury may occur. Stand to either side of theblade.

• Never perform layout, assembly or set-up work on the

table/work area when the machine is running. A sudden

slip could cause a hand to move into the blade. Severe injury

canresult.

ENGLISH

• Never perform any adjustments while the saw is running

such as fence repositioning or removal, bevel lock

adjustment, or blade heightadjustment.

• Clean the table/work area before leaving the machine.

Lock the switch in the “OFF” position and disconnect tool from

power source to prevent unauthorizeduse.

• Always lock the fence and bevel adjustment

beforecutting.

• Avoid overheating the saw blade tips. Keep material

moving and parallel with the fence. Do not force work into

theblade.

• If cutting plastic materials, avoid melting theplastic.

• Do not leave a long board (or other workpiece)

unsupported so the spring of the board causes it to shift

on the table resulting in loss of control and possible

injury. Provide proper support for the workpiece, based on its

size and the type of operation to be performed. Hold the work

firmly against the fence and down against the tablesurface.

• If this saw makes an unfamiliar noise or if it vibrates

excessively, cease operating immediately, turn unit

off and disconnect tool from power source until the

problem has been located and corrected. Contact a

DeWALT factory service centre, a DeWALT authorized service

centre or other qualified service personnel if the problem can

not befound.

• Do not operate this machine until it is completely

assembled and installed according to the instructions. A

machine incorrectly assembled can cause seriousinjury.

• Never attempt to cut a stack of loose pieces of material

which could cause loss of control or kickback. Support all

materialssecurely.

Saw Blades



WARNING: to minimise the risk of kickback and to ensure

proper cutting, the splitter and riving knife must be the

proper thickness for the blade used. If a different blade

is used, check the blade body (plate) thickness and the

blade kerf (cutting) width marked on the blade or on the

blade packaging. The splitter and riving knife thickness

must be greater than the body thickness and less than the

kerfwidth.

• Do not use saw blades that do not conform to the dimensions

stated in the Technical Data. Do not use any spacers to make

a blade fit onto the spindle. Use only the blades specified in this

manual, complying with EN847-1, if intended for wood and

similarmaterials.

• Consider applying specially designed noise-reductionblades.

• Do not use high steel (HS) sawblades.

• Do not use cracked or damaged sawblades.

• Ensure that the chosen saw blade is suitable for the material

to becut.

• Always wear gloves for handling saw blades and rough

material. Saw blades should be carried in a holder

whereverpracticable.

Residual risks

The following risks are inherent to the use of saws:

• injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of accidents caused by the uncovered parts of the rotating

sawblade.

• Risk of injury when changing the saw blade with

unprotectedhands.

• Risk of squeezing fingers when opening theguards.

• Health hazards caused by breathing dust developed when

sawing wood, especially oak, beech andMDF.

The following factors are of influence to noise production:

• the material to be cut

• the type of saw blade

• the feed force

• machine maintenance

The following factors are of influence to dust exposure:

• worn saw blade

• dust extractor with air velocity less than 20 m/s

• workpiece not exactly guided

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the power supply corresponds to the voltage

on the ratingplate.

Your DeWALT tool is double insulated in accordance

with IEC60745; therefore no earth wire isrequired.



WARNING: 220-240V units have to be operated via a fail-

safe isolating transformer with an earth screen between

the primary and secondarywinding.

If the supply cord is damaged, it must be replaced only by

DeWALT or an authorised serviceorganisation.

NOTE: This device is intended for the connection to a power

supply system with maximum permissible system impedance

Zmax of 0.28 Ω at the interface point (power service box)

of user’s supply. The user has to ensure that this device is

connected only to a power system which fulfills the requirement

above. If necessary, the user can ask the public power supply

company for the system impedance at the interface point.

Using an Extension Cable

If an extension cable is required, use an approved 3–core

extension cable suitable for the power input of this tool (see

Technical Data).The minimum conductor size is 1.5 mm

; the

maximum length is 30m.

When using a cable reel, always unwind the cablecompletely.

ENGLISH

Package Contents

The package contains:

1 Partly assembled machine

1 Rip fence

1 Mitre gauge

1 Upper blade guard assembly

1 Throat plate

2 Blade wrenches

1 Push Stick

1 Dust extraction adapter

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Wear respiratoryprotection.

Keep hands away from cutting area and theblade.

Riving knife or splitter thickness

Saw blade body thickness and kerf width

Saw blade diameter

Blade guard release lever

Lock/unlock cover at the mainswitch.

Unplug saw before changing blade

Protect the supply cord/plug against humidity and

sharp edges of saw blade

Date Code Position (Fig. A)

The Date Code

51

, which also includes the year of

manufacture, is printed into thehousing.

Example:

2020 XX XX

Year of Manufacture

Description (Fig. A, B)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

Table

Blade(Sawblade is not included for A9 and IN products)

Rip scale indicator

Fine adjust knob

Rail lock lever

Blade height adjustment wheel

Bevel lock lever

ON/OFF switch

Mounting holes

Mitre gauge

Blade guard assembly

Blade guard release lever

Splitter

Dust exhaust port

Guard dust exhaust port

Throat plate

Rip fence

Rip fence latch

Work support/narrrow rip fence(shown in stored position)

Blade wrenches

Push stick(shown in stored position)

Carrying handles

Non-through cutting riving knife

(shown in storage position)

Intended Use

DWE7492 table saw is designed for professional ripping, cross-

cutting, mitreing and bevelling with various materials as wood,

wood composite materials andplastics.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

DO NOT use for cutting metal, cement board, ormasonry.

DO NOT use shaping cutter heads on thissaw.

DO NOT perform tapered cuts without a tapered jigaccessory.

DO NOT use the saw for plunge or cove cutting.

These table saws are professional powertools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

ENGLISH

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

without supervision. This product is not intended for use

by persons (including children) suffering from diminished

physical, sensory or mental abilities; lack of experience,

knowledge or skills unless they are supervised by a person

responsible for their safety. Children should never be left

alone with thisproduct.

ASSEMBLY



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Unpacking

• Remove the saw from the packaging materialcarefully.

• The machine is fully assembled except for the rip fence,

blade guard assembly, mitre gauge, blade wrenches, and

dust extraction reducerport.

• Finalize the assembly following the instructions as

describedbelow.



WARNING: Always keep the push stick in its place when

not inuse.

Mounting the Saw Blade(Fig.A,C)



WARNING: To reduce the risk of injury, turn unit

off and disconnect machine from power source

before installing and removing accessories, before

adjusting or changing set-ups or when making

repairs. An accidental start-up can causeinjury.



WARNING: When mounting the saw blade, wear

protective gloves. The teeth of the saw blades are very

sharp and can bedangerous.



WARNING: The saw blade MUST be replaced as described

in this section. ONLY use saw blades as specified under

Technical Data.



WARNING: Do not touch the saw blade after working

before it has cooled. The saw blade becomes very hot

whileworking.

1. Raise the saw blade arbor to its maximum height by turning

the blade height adjustment wheel

6

clockwise.

2. Remove the throat plate

16

. Refer to Mounting the

ThroatPlate.

3. Using wrenches

20

, loosen and remove the arbor

nut

22

and flange

24

from the saw arbor by turning

anti-clockwise.

4. Place the saw blade on to the spindle

23

making sure the

teeth of the blade

2

point down at the front of the table.

Assemble the washers and arbor nut to the spindle and

tighten arbor nut

22

as far as possible by hand, making sure

that the saw blade is against the inner washer and the outer

flange

24

is against the blade. Ensure the largest diameter

of the flange is against the blade. Ensure the spindle and

washers are free from dust anddebris.

5. To keep the spindle from rotating when tightening the

arbor nut, use the open end of the blade wrench

20

secure thespindle.

6. Using the arbor wrench, tighten the arbor nut

22

turning itclockwise.

7. Replace the throatplate.



WARNING: Always check the rip fence pointer and the

blade guard assembly after having changed theblade.

Mounting the Blade Guard Assembly/

Riving Knife (Fig.A,D)



WARNING: Use the guard assembly for all

throughcutting.



WARNING: Use the riving knife for non-through-cutting

when blade guard assembly cannot beused.



WARNING: Do not insert both the blade guard assembly

and the non-through-cutting riving knife into the clamp

at the same time.

NOTE: The saw is shipped with the non-through-cutting riving

knifeinstalled.

1. Raise the saw blade arbor to its maximumheight.

2. Install blade guard assembly by pulling the guard release

lever

12

and inserting either the non-through-cutting

riving knife

52

or the blade guard assembly

11

until it

bottomsout.

3. Release lever, make sure clamp plates are fully closed and

clamp the splittersecurely.



WARNING: Before connecting the table saw to the power

source or operating the saw, always inspect the blade

guard assembly for proper alignment and clearance

with saw blade. Check alignment after each change of

bevelangle.



WARNING: To reduce the risk of serious personal injury,

DO NOT operate saw if blade assembly is not securely

clamped inplace.

When properly aligned, the splitter

13

or riving knife

52

will

be in line with the blade at both table top level, and at the top

of the blade. Using a straight edge, ensure that the blade

2

aligned with the splitter

13

 or riving knife

52

. With power

disconnected, operate the blade tilt and height adjustments

through the extremes of travel and insure the blade guard

assembly clears the blade in alloperations. Refer to Aligning

Guard Assembly/Splitter to Blade.



WARNING: Correct mounting and alignment of the blade

guard assembly is essential to safe operation!

To Remove the Blade Guard Assembly/

Riving Knife (Fig.D)

1. Pull the guard release lever

12

2. Lift up on blade guard assembly

11

or riving knife

52

Mounting the Throat Plate(Fig.E)

1. Align the throat plate

16

as shown in FigureE, and insert

the tabs on the back of the throat plate into the holes on the

back of the tableopening.

ENGLISH

2. Turn the locking screw

40

clockwise 90° to lock the table

insert inplace.

3. The throat plate includes four adjustment screws

25

which

raise or lower the throat plate. When properly adjusted, the

front of the throat plate should be flush or slightly below the

surface of the table top and secured in place. The rear of the

throat plate should be flush or slightly above the tabletop.



WARNING: Never use the machine without the throat

plate. Immediately replace the throat plate when worn

ordamaged.

To Remove the Throat Plate

1. Remove the throat plate

16

by turning the locking

screw

40

90˚ anti-clockwise

2. Using finger hole

26

, pull throat plate up and forward

to expose the inside of the saw. DO NOT operate the saw

without the throat plate. If using a dado blade, use proper

dado throat plate (sold separately).

Fitting the Rip Fence(Fig.F)

The rip fence can be installed in two positions on the

right(Position 1 for 0 mm to 62 cm ripping, and Position 2 for

20.3 cm to 82.5 cm ripping) and one position on the left of your

tablesaw.

1. Unlock the rip fence latches

18

2. Holding the fence at an angle, align the locator

pins(front and back)

29

on the fence rails with the fence

headslots

30

3. Slide the head slots onto the pins and rotate the fence down

until it rests on therails.

4. Lock the fence in place by closing the front and back

latches

18

onto therails.

Bench Mounting(Fig.A)



CAUTION: To reduce the risk of personal injury, make sure

table saw is firmly mounted to a stable surface beforeuse.



CAUTION: Ensure that the surface is stable enough

that large pieces of material will not cause it to tip over

duringuse.

The table saw must be mounted firmly. Four holes

9

are

provided in the tool’s base for mounting. We strongly

recommend that these holes be used to anchor the table saw to

your workbench or other stationary rigidframe.

1. Centre the saw on a square piece of 12.7mmplywood.

2. Mark the positions of the two rear mounting holes(spaced

220 mm apart) in the frame of the saw with a pencil. Then

measure forward 498.5 mm for the two front holes spaced

230 mmapart.

3. Remove the saw and drill 9 mm holes in the places you have

justmarked.

4. Position the saw over the four holes you drilled in the

plywood and insert four 8mm machine screws FROM

THE BOTTOM. Install washers and 8mm nuts on the top.

Tightensecurely.

5. In order to prevent the screw heads from marring the

surface to which you clamp the saw, attach two strips of

scrap wood to the bottom of the plywood base. These strips

can be attached with wood screws installed from the top

side as long as they don’t protrude through the bottom of

thestrip.

6. Use a “C” clamp to secure the plywood base to your

workbench whenever you use thesaw.

ADJUSTMENTS

Blade Adjustment(Fig.G)

Blade Alignment (Parallel to Mitre Slot)



WARNING: Cut Hazard. Check the blade at 0˚ and 45˚

to make sure blade does not hit the throat plate, causing

personalinjury.

If the blade appears to be out of alignment with the mitre slot

on the table top, it will require calibration for alignment. To

realign the blade and mitre slot, use the following procedure:



WARNING: To reduce the risk of injury, turn unit

off and disconnect machine from power source

before installing and removing accessories, before

adjusting or changing set-ups or when making

repairs. An accidental start-up can causeinjury.

1. Using a 5mm hex wrench, loosen rear pivot bracket

fasteners

32

, located on the underside of the table, just

enough to allow the bracket to move side-to-side.

2. Adjust the bracket until the blade is parallel to the mitre

gaugeslot.

3. Tighten the rear pivot bracket fasteners to 12.5–13.6 Nm

(110–120 in-lbs).

Blade height adjustment(Fig.A)

The blade can be raised and lowered by turning the blade

height adjustment wheel

6

Make sure the top three teeth of the blade are just breaking

through the upper surface of the workpiece when sawing. This

will ensure that the maximum number of teeth are removing

material at any given time, thus giving optimumperformance.

Aligning Guard Assembly/Splitter to

Blade(Fig.A, H)

1. Remove the throat plate. Refer to Remove ThroatPlate.

2. Raise the blade to full depth of cut and 0° bevelangle.

3. Locate the three small set screws

39

adjacent to the guard

assembly lock shaft

38

. These screws will be used to adjust

the guard assemblyposition.

4. Lay a straight edge on the table against two blade tips. The

splitter

13

should not touch the straight edge. If needed,

loosen the two larger lock screws

41

5. Adjust the small set screws

39

to move the splitter

according to the position noted in step 4. Lay the straight

edge on the opposite side of the blade and repeat

adjustments asneeded.

6. Lightly tighten the two larger lock screws

41

ENGLISH

7. Place a square flat against the splitter to the verify splitter is

vertical and in-line with theblade.

8. If needed, use the set screws to bring the splitter vertical

with thesquare.

9. Repeat steps 4 and 5 to verify position ofsplitter.

10. Fully tighten the two larger lock screws

41

11. Re-install and lock the throat plate

16

Parallel Adjustment(Fig.A,I,J,O)



WARNING: A misaligned fence, not parallel to the blade,

increases the risk of kickback!

For optimum performance, the blade must be parallel to the

rip fence. This adjustment has been made at the factory. To

re-adjust:

Position 1 Fence Alignment

1. Install the fence in position 1 and unlock the rail lock

lever

5

. Locate both locator pins

29

that support the fence

on the front and rearrails.

2. Loosen the rear locator pin screw and adjust the alignment

of the fence in the groove until the fence face is parallel to

the blade. Make sure you measure from the fence face to

the front and back of the blade to ensurealignment.

3. Tighten the locator screw and repeat on the left side of

theblade.

4. Check rip scale pointer adjustment(Fig.J).

Position 2 Fence Alignment

1. To align position 2 fence locator pins

29

, ensure

position 1 pins have been aligned, refer to Position 1

FenceAlignment.

2. Loosen the position 2 pins, then using the blade wrench

holes as a guide for positioning, align the pins(Fig.O).

3. Tighten the locator pins(front and rear).

Adjusting the Rip Scale(Fig.A, J)

1. Unlock the rail lock lever

5

2. Set the blade at 0° bevel and move the fence in until it

touches theblade.

3. Lock the rail locklever.

4. Loosen the rip scale indicator screws

31

and set the rip

scale indicator to read zero(0). Retighten the rip scale

indicator screws. The yellow rip scale(top) reads correctly

only when the fence is mounted on the right side of

the blade and is in position 1(for zero to 62 cm ripping)

not the 82.5 cm rip position. The white scale(bottom)

reads correctly only when the fence is mounted on the

right side of the blade and in position 2(for 20.3 cm to

82.5cmripping).

The rip scale reads correctly only when the fence is mounted to

the right of theblade.

Rail Lock Adjustment(Fig.A,K)

The rail lock has been factory-set. If you need to re-adjust,

proceed as follows:

1. Lock the rail lock lever

5

2. On the underside of the saw, loosen the jam nut

33

3. Tighten the hex rod

34

until the spring on the locking

system is compressed creating the desired tension on the

rail lock lever. Retighten the jam nut against the hexrod.

4. Flip the saw over and check that the fence does not move

when the lock lever is engaged. If the fence is still loose,

tighten the springfurther.

Bevel Stop and Pointer Adjustment(Fig.L)

1. Raise the blade fully by rotating the blade height

adjustment wheel

6

clockwise until itstops.

2. Unlock the bevel lock lever

7

by pushing it up and to the

right. Loosen the bevel stop screw

36

3. Place a square flat against the table top and against the

blade between teeth. Ensure the bevel lock lever is in its

unlocked, or upposition.

4. Using the bevel lock lever, adjust the bevel angle until the

blade is flat against thesquare.

5. Tighten the bevel lock lever by pushing itdown.

6. Turn the bevel stop cam

35

until it firmly contacts the

bearing block. Tighten the bevel stop screw

36

7. Check the bevel angle scale. If the pointer does not read 0°,

loosen pointer screw

37

and move the pointer so it reads

correctly. Retighten the pointerscrew.

8. Repeat at 45°, but do not adjustpointer.

Mitre Gauge Adjustment(Fig.A)

To adjust mitre gauge

10

loosen knob, set to desired angle and

tightenknob.

Body and Hand Position

Proper positioning of your body and hands when operating the

table saw will make cutting easier, more accurate andsafer.



WARNING:

• Never place your hands near the cuttingarea.

• Place your hands no closer than 150mm from

theblade.

• Do not cross yourhands.

• Keep both feet firmly on the floor and maintain

properbalance.

Prior to Operation



WARNING:

• Install the appropriate saw blade. Do not use

excessively worn blades.The maximum rotation speed

of the tool must not exceed that of the sawblade.

• Do not attempt to cut excessively smallpieces.

• Allow the blade to cut freely. Do notforce.

• Allow the motor to reach full speed beforecutting.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.

ENGLISH



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The attention of UK users is drawn to the “woodworking

machines regulations 1974” and any subsequentamendments.

Ensure the machine is placed to satisfy your ergonomic

conditions in terms of table height and stability. The machine

site shall be chosen so that the operator has a good overview

and enough free surrounding space around the machine that

allows handling of the workpiece without anyrestrictions.

To reduce effects of increased vibration, make sure the

environment is not too cold, the machine and accessory are well

maintained and the workpiece size is suitable for thismachine.



WARNING:

• Ensure the machine is placed to satisfy ergonomic

conditions in terms of table height and stability. The

machine site shall be chosen so that the operator

has a good overview and enough free surrounding

space around the machine that allow handling of the

workpiece without anyrestrictions.

• Install the appropriate saw blade. Do not use

excessively worn blades. The maximum rotation speed

of the tool must not exceed that of the sawblade.

• Do not attempt to cut excessively smallpieces.

• Allow the blade to cut freely. Do notforce.

• Allow the motor to reach full speed beforecutting.

• Make sure all locking knobs and clamp handles

aretight.

• Never place either hand in the blade area when the

saw is connected to the electrical powersource.

• Never use your saw for freehand cuts!

• Do not saw warped, bowed or cupped workpieces.

There must be at least one straight, smooth side to go

against the rip fence or mitrefence.

• Always support long workpieces to preventkickback.

• Do not remove any cut-offs from the blade area while

the blade isrunning.

Switching On and Off(Fig.M)

The on/off switch

8

of your saw bench offers

multipleadvantages:

• No-volt release function: should the power be shut off for

any reason, the switch has to be deliberatelyreactivated.

• To switch the machine on, press the green startbutton.

• To switch the machine off, press the red stopbutton.

Lock Off Feature Instructions

A cover above the switch folds down for insertion of a padlock

to lock the saw off. A padlock with a maximum diameter of

6.35mm and minimum clearance of 76.2 mm isrecommended.

Rip Fence Operation(Fig.N–P)

Rail lock lever

The rail lock lever

5

locks the fence in place preventing

movement during cutting. To lock the rail lever, push it down

and toward the rear of the saw. To unlock, pull it up and toward

the front of thesaw.

NOTE: When ripping, always lock the rail locklever.

Work Support Extension /

Narrow Ripping Fence

Your table saw is equipped with a work support extension to

support work that extends beyond the sawtable.

To use the narrow ripping fence in the work support position,

rotate it from its stored position as shown in FigureO, and

slide the pins into the lower sets of slots

27

on both ends of

thefence.

To use the narrow ripping fence in the narrow ripping position,

snap the pins into the upper sets of slots

28

on both ends of

the fence. This feature will allow 51mm of extra clearance to the

blade. Refer to FigureP.

NOTE: Retract the work support extension or adjust to narrow

rip fence position whenever working over thetable.

NOTE: When using the narrow ripping fence, subtract 51mm

from the indicated rip scalereading.

Fine Adjustment Knob

The fine adjustment knob

4

allows smaller adjustments when

setting the fence. Before adjusting, be sure the rail lock lever is in

its up or unlocked,position.

Rip Scale Pointer

The rip scale pointer will need to be adjusted for proper

performance of the rip fence if the user switches between thick

and thin kerf blades. The rip scale pointer only reads correctly

when the fence is installed in position 1 or 2 to the right side

of the blade. When using the narrow ripping fence for narrow

ripping (not in work support position), subtract 51mm from

the indicated rip scale reading. See Adjusting the Rip Scale

underAdjustments.

BASIC SAW CUTS

Through-Cutting Operations



WARNING: Use blade guard assembly for all through-

cutting operations.

Ripping(Fig.A,B, Q, R)



WARNING: Sharpedges.

1. Set the blade to 0°.

2. Install the rip fence and lock the rip fence latch

18

(Fig.A).

3. Raise the blade until it is about 3 mm higher than the top of

the workpiece. Adjust the height of the upper blade guard

asnecessary.

4. Adjust the position of the fence and lock the rail lock

lever

5

, refer to Rip FenceOperation.

ENGLISH

5. Hold the workpiece flat on the table and against the fence.

Keep the workpiece away from theblade.

6. Keep both hands away from the path of the blade(Fig.Q).

7. Switch the machine on and allow the blade to reach

fullspeed.

8. Slowly feed the workpiece underneath the guard, keeping

it firmly pressed against the rip fence. Allow the teeth to

cut, and do not force the workpiece through the blade. The

blade speed should be keptconstant.

9. Always use a push stick

21

when working close to the

blade(Fig.R).

10. After completing the cut, switch the machine off, allow the

blade to stop and remove theworkpiece.



WARNING:

• Never push or hold the "free" or cut-off-side of

theworkpiece.

• Do not cut excessively smallworkpieces.

• Always use a push stick when ripping

smallworkpieces.

Bevel Cuts(Fig.A)

1. To set the required bevel angle, rotate the bevel lock

lever

7

by pushing it up and to theright.

2. To set to desired angle, rotate the lever by pushing it down

and to the left to lock inplace.

3. Proceed as forripping.

Cross-Cutting and Bevel Crosscutting (Fig. Q)

1. Remove the rip fence and install the mitre gauge in the

desiredslot.

2. Lock the mitre gauge at 0°.

3. Proceed as forripping.

Mitre Cuts(Fig.A)

1. Set the mitre gauge

10

to the requiredangle.

NOTE: Always hold the workpiece tightly against the face of the

mitregauge.

2. Proceed as forripping.

Compound Mitre

This cut is a combination of a mitre and a bevel cut. Set the

bevel to the angle required and proceed as for a cross-cutmitre.

Support for Long Pieces

• Always support longpieces.

• Support long workpieces using any convenient means

such as saw-horses or similar devices to keep the ends

fromdropping.

Non-Through-Cutting

(Grooving and Rabbeting)



WARNING: Remove the blade guard assembly

11

and

install the non-through-cutting riving knife

52

for non-

through-cutting operations. Use featherboards for all

non-through-cutting operations where the blade guard

assembly, anti-kickback assembly and riving kife cannot

beused.

Instructions in the Ripping, Crosscutting, Bevel Crosscutting,

Mitreing, and Compound Mitreing sections are for cuts

made through the full thickness of the material. The saw can

also perform non-through cuts to form grooves or rabbets in

thematerial.

Non-Through-Ripping (Fig. D, U)



WARNING: A rip fence should ALWAYS be used for

ripping operations to prevent loss of control and personal

injury. NEVER perform a ripping operation freehand.

ALWAYS lock the fence to therail.



WARNING: When bevel ripping and whenever possible,

place the fence on the side of the blade so that the blade is

tilted away from the fence andhands.



WARNING: Keep hands clear of theblade. With non-

through-cutting the blade is not always visible during the

cut, so increased caution is necessary to ensure hands are

clear of theblade.



WARNING: Use a push stick to feed the workpiece if there

are 51–152mm between the fence and the blade. Use a

narrow ripping fence feature and push block to feed the

workpiece if there are 51mm or narrower between the

fence and theblade.

1. Remove the blade guard assembly

11

and install the non-

through-cutting riving knife

52

(Fig. D). Refer to: Mounting

the Blade Guard Assembly/RivingKnife.

2. Lock the rip fence by pressing the rail lock lever down.

Remove the mitregauge.

3. Raise the blade to the desired cutdepth.

4. Hold the workpiece flat on the table and against the fence.

Keep the workpiece about 25.4mm away from theblade.



WARNING: The workpiece must have a straight edge

against the fence and must not be warped, twisted or

bowed. Keep both hands away from the blade and away

from the path of the blade. See proper hand position in

FigureU.

5. Turn the saw on and allow the blade to come up to speed.

Both hands can be used in starting the cut. When there

are approximately 305mm left to be ripped, use only one

hand, with your thumb pushing the material, your index and

second finger holding the material down and your other

fingers hooked over the fence. Always keep your thumb

along side your first two fingers and near thefence.

6. Keeping the workpiece against the table and fence, slowly

feed the workpiece rearward all the way through the saw

blade. Continue pushing the workpiece until it is clear of the

blade guard assembly and it falls off the rear of the table. Do

not overload themotor.

7. Never try to pull the workpiece back with the blade turning.

Turn the switch off, allow the blade to stop and slide the

workpieceout.

8. When sawing a long piece of material or a panel, always use

a work support. A sawhorse, rollers, or out feed assembly

provides adequate support for this purpose. The work

ENGLISH

support must be at the same height or slightly lower than

the sawtable.

Non-Through-Ripping Small Pieces (Fig. A)

It is unsafe to rip small pieces. It is not safe to put your hands

close to the blade. Instead, rip a larger piece to obtain the

desired piece. When a small width is to be ripped and the hand

cannot be safely put between the blade and the rip fence, use

one or more push sticks. A push stick

21

is included with this

saw, attached to the rip fence. Use the push stick(s) to hold the

workpiece against the table and fence, and push the workpiece

fully past theblade.

Non-Through-Bevel Ripping (Fig. V)

This operation is the same as non-through-cut ripping except

the bevel angle is set to an angle other than zero degrees. For

proper hand position, Refer to FigureV.



WARNING: Before connecting to power source or

operating the saw, always inspect the riving knife for

proper alignment and clearance with saw blade. Check

alignment after each change of bevelangle.

Non-Through-Crosscutting (Fig. W)



WARNING: NEVER use rip fence in combination with

mitregauge.



WARNING: To reduce the risk of injury, NEVER use the

fence as a guide or length stop whencrosscutting.



WARNING: When using a block as a cut-off gauge,

the block must be at least 19mm thick and is very

important that the rear end of the block be positioned

so the workpiece is clear of the block before it enters the

blade to prevent contact with blade resulting in a thrown

workpiece and possiblyinjury.

1. Remove the rip fence and place the mitre gauge in the

desiredslot.

2. Adjust the blade height to the desired cutdepth.

3. Hold the workpiece firmly against the mitre gauge

10

with

the path of the blade in line with the desired cut location.

Keep the workpiece an inch or so in front of the blade. KEEP

BOTH HANDS AWAY FROM THE BLADE AND THE PATH OF

THE BLADE (Fig. W).

4. Start the saw motor and allow the blade to come up

tospeed.

5. While using both hands to keep the workpiece against

the face of the mitre gauge, and holding the workpiece

flat against the table, slowly push the workpiece through

theblade.

6. Never try to pull the workpiece with the blade turning. Turn

the switch off, allow the blade to stop, and carefully slide the

workpieceout.

Non-Through-Bevel Crosscutting

This operation is the same as crosscutting except that the bevel

angle is set to an angle other than 0°.



WARNING: Before connecting to power source or

operating the saw, always inspect the riving knife for

proper alignment and clearance with saw blade. Check

alignment after each change of bevelangle.

Non-Through-Mitreing (Fig. W)

This operation is the same as crosscutting except the mitre

gauge is locked at an angle other than 0°. Hold the workpiece

FIRMLY against the mitre gauge

10

and feed the workpiece

slowly into the blade (to prevent the workpiece from moving).

Non-Through-Mitre Gauge Operation

To set your mitre gauge:

1. Loosen the mitre gauge lockknob

46

2. Move the mitre gauge to the desiredangle.

3. Tighten the mitre gauge lockknob.

Non-Through-Compound Mitreing

This is a combination of non-through-bevel crosscutting and

non-through-mitreing. Follow the instructions for both non-

through-bevel crosscutting and non-through-mitreing.

Dust extraction(Fig.A, AA)

The machine is provided with a dust exhaust port

14

at the

rear of the machine suitable for use with dust extraction

equipment featuring 57/65 mm nozzles. Supplied with the

machine is a reducer port for use of dust extraction nozzles

of 34–40 mmdiameter.

Supplied with the machine is a reducer port for use with the

DEWALT AirLock system (DWV9000-XJ).

The blade guard assembly also features a dust exhaust port for

35mm nozzles or direct attachment to the DEWALT AirLock

(DWV9000-XJ).

Dust from materials such as lead-containing coatings and some

wood types, can be harmful to one’s health. Breathing-in the

dust can cause allergic reactions and/or lead to respiratory

infections of the user orbystanders.

Certain dust, such as oak or beech dust, is considered

carcinogenic, especially in connection with wood-

treatmentadditives.

Observe the relevant regulations in your country for the

materials to beworked.

The vacuum cleaner must be suitable for the material

beingworked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use dust class M vacuumcleaner.

The blade guard assembly also features a dust exhaust port for

35 mm nozzles (M class vacuum).

• During all operations, connect a dust extraction device

designed in accordance with the relevant regulations

regarding dustemission.

• Ensure that the dust extraction hose in use is suitable for

the application and material being cut. Ensure proper

hosemanagement.

• Be aware that man-made materials such as chipboard

or MDF produce more dust particles during cutting than

naturaltimber.

ページが読み込まれています...

DeWalt DWE7492 ユーザーマニュアル

ブランド: DeWalt

モデル: DWE7492

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: DeWalt DWE7492 User manual

DeWalt DWE7492 ユーザーマニュアル

DeWalt DWE7492 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント