Stanley STEL630 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
STEL630
3
11
2
ENGLISH
A
1
B
C
D
E
F
G
1c
J
1d
K
1e
L
M
N
1b
I
3
ENGLISH
7
H
I
H
4
C
D
E
5
6
3
C
C
2
A
B
4
ENGLISH
10
F
J
G
12
O
13
8
9
F
I
G
11
L
K
11a
11b
11c
11d
L
11e
5
ENGLISH
14
L
M
11c
11d
15
L
N
6
ENGLISH
STEL630 Electric Planer
Technical Data
Specification STEL630
Power input W
650
No-load speed /min 16,500
Planing width
mm
82
Planing depth mm 1.6
Rebating depth mm 12
Weight kg 2.7
Intended use
Your Stanley planer has been designed for planing wood,
wood products and plastics. The tool is intended for hand-held
use.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of �ammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the in�uence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
7
ENGLISH
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other
condition that may affect the power tools operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualifed repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for planers
Hold the tool by the insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
Keep the cutter sharp. Dull or damaged cutters may cause
the planer to swerve or stall under pressure. Always use
the appropriate type of cutter for the power tool.
Do not touch the workpiece or the cutter immediately after
operating the tool. They can become very hot.
Remove all nails and metal objects from the workpiece
before planning.
Always hold the tool with both hands and by the handles
provided.
Immediately disconnect the cable from the mains if it is
damaged or cut.
Warning! Contact with, or inhalation of dusts arising from
planing applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also protected.
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service
Centre in order to avoid a hazard.
8
ENGLISH
Features
A. Trigger switch
B. Lock-on button
C. Depth adjustment knob/front handle
D. Switch Handle
E. Shoe
F. Chip discharge chute
G. Chip deflector lever
H. Parallel fence
I. Collection bag(Not included)
J. Vac adaptor (Not included)
K. Wrench
L. Blades
M. Adjust plate
N. Sharpening holder
Operation
Switch (Figure 2)
@
CAUTION: Check that the tool is not locked ON before
connecting it to a power supply. If the trigger switch is locked
ON when the tool is connected to the power supply, it will start
immediately. Damage to your tool or personal injury may
result.
@
CAUTION: Allow the tool to reach full speed before
touching tool to the work surface. Lift the tool from the work
surface before turning the tool off. To start the planer, depress
the trigger switch (A) in �gure 2 . To turn the planer off, release
the trigger switch.
Lock-On Button (Figure 2)
The tool can be locked on for continuous use. To lock the tool
ON depress the trigger switch (A) and push in the lock-on
button (B). Hold the lock-on button in as you gently release
the trigger switch. The tool will continue to run. To turn the tool
OFF from a locked-on position, squeeze and release the
trigger once.
Adjusting Planing Depth (Figure 3)
@
WARNING: Turn off and unplug the tool before making any
adjustments or removing or installing accessories. Planing
depth is infinitely variable from 0 to 1.6 mm. To adjust the
cutting depth, rotate the depth adjustment knob/front handle
(C) clockwise from the “P” position. The cutting depth will
increase from 0 to as much as 1.6mm. It is recommended that
test cuts be made in scrap wood after each re-adjustment to
make sure that the desired amount of wood is being removed
by the planer. Several shallow passes (rather than one deep
one) will produce a smoother finish.
Planing (Figures 4, 5, 6)
@
CAUTION: Allow the tool to reach full speed before
touching tool to the work surface. Lift the tool from the work
surface. Lift the tool from the work surface before turning the
tool off.
Hold the planer in the correct position with one hand on the
front handle (C) and the other hand on the switch handle (D)
as shown in �gure 4 . Place the front of the shoe (E) on the
surface to be planed, making certain that the cutting blades
are not touching the surface. Push down firmly on the front
handle of the planer so that the front shoe is ABSOLUTELY
FLAT on the work surface. Squeeze the trigger switch and
allow the motor to reach full speed before touching the planer
blades to the work surface. Move the tool slowly into the work
and maintain downward pressure to keep the planer flat. Be
particularly careful to keep the tool flat at the beginning and
the end of the work surface (Figures 4, 5, 6 ).
Planing Tip: For a smoother appearance, fasten a piece of
scrap wood to the end of the piece you are planing. Don t stop
planing until the cutting blades of the planer are past your
work piece and into the scrap material.
Parallel Fence (Figures 7, 8)
@
WARNING: Turn off and unplug the tool before making any
adjustments or removing or installing accessories.
@
CAUTION: Allow the tool to reach full speed before
touching tool to the work surface. Lift the tool from the work
surface before turn ing the tool off.
The rabbet fence can be installed on either side of your
planer. The planer can make rabbet cuts up to 12mm.
Fitting and removing the parallel fence(fig.7)
The parallel fence is used to for optimum control on narrow
workpieces.
loosen the locking knob(9).
insert the parallel fence(H)through the opening(10).
slide the parallel fence into the desired position.
Rebating(fig.8)
Fit and adjust the parallel fence.
proceed as for planing.
Collection Bag (Figure 9)
@
WARNING: Turn off and unplug the tool before
making any adjustments or removing or installing
accessories (Bag not included in all models).
a. Attach bag (I) to either side of chip discharge chute (F).
Empty bag often to prevent clogging. b.To prevent chips
from coming out opposite side of chip discharge chute,
move chip deflector lever (G) to the opposite side of the
bag.
9
ENGLISH
Vacuum Adaptor (Figure 10)
@
WARNING: Turn off and unplug the tool before making
any adjustments or removing or installing accessories.
a. Slide the vac adaptor (J) over the chip discharge chute
(F).
b. Connect a vacuum cleaner hose (not included) to the
adaptor.
c. To prevent chips from coming out opposite side of chip
discharge chute, move chip deflector lever (G) to the
opposite side of the adaptor.
To Change Blades (Figure11)
@
WARNING: Turn off and unplug the tool before making
any adjustments or removing or installing accessories.
@
WARNING: Cut Hazard. Planer blades are sharp and
must be handled with care.
NOTE: The STEL630 has two blades, one on each side of
the blade drum. Any operation or adjustment should be made
to both blades.
To Remove Blade (Figure 11)
a. Remove the three bolts (11a) with the wrench (K) supplied.
b. Remove drum cover (11b) and remove the blade (L) out of
its holder.
c. Place the blade or replaced it.
To Reinstall Blade
a. Replace the drum cover (11b). Make sure that the blade is
flush with the planing shoe.
b. Tighten the three bolts (11a) .
@
Always replace both blade.
Parking Foot (Figure 12)
Your planer is equipped with a parking foot (O) that
automatically lowers into place when the tool is lifted from the
work surface. When planing, the parking foot raises as the tool
is pushed forward. When the parking foot is lowered, the
planer can set on the work surface without the blade touching.
@
CAUTION: Do not lock the trigger switch on and engage
the parking foot. The vibration of the running motor will cause
the planer to move, possibly falling from the work piece.
Drive Belt (Figure 13)
WARNING: Turn off and unplug the tool before making
any adjustments or removing or installing accessories.
To Replace Belt
a. Loosen the three screws shown in �gure 13 and remove
the belt cover.
b. Remove old belt.
c. Place new belt over front pulley then rotate belt clockwise
while pushing belt onto back pulley.
d. Attach belt cover and securely tighten screws.
Adjusting cutters (Figure 14)
a. Place the blade (L) on the adjust plate (M),and make the
blade edge perfectly flush with the inside edge of the
adjust plate (M).
b. Place the bracket (11d) on the blade and make the flange
of bracket flush with the back side of the adjust plate.
c. Tighten the two screws (11c) on the bracket.
d. Slip the flange of the bracket into the groove of drum
(11e).place the drum cover (11b) and tighten the three
bolts (11a).
Sharpening blades (Figure 15)
a. Fasten the blades to sharpening holder (N). Be sure both
blades edges face in the same direction.
b. Place the blades edges so that they rest flat on the
grinding stone.
c. Firmly grip the sharpening holder and move back and
forward to sharpen the blades (L).
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving
parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
Adjust the depth of cut.
If necessary, fit and adjust the parallel fence.
Hints for optimum use
Move the tool along the grain of the wood.
If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only
a very thin shaving at each pass and take several passes
to achieve the desired result.
To keep the tool in a straight line, press down the front of
10
ENGLISH
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
Accessories
The performance of your tool depends on the accessory used.
Stanley accessories are engineered to high quality standards
and designed to enhance the performance of your tool. By using
these accessories you will get the verybest from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a soft
brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Replacing the drive belt (�g. 13)
Loosen the screws and remove the cover .
Remove the old drive belt.
Place the new belt over the pulleys. Place the belt over
the large pulley first, then over the small pulley, whilst
manually rotating the belt steadily.
Put the cover back in place and tighten the screws.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available
for separate collection.
z
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
繁體中文
11
STEL630
STEL630
W
650
/min 16,500
mm 82
mm 1.6
mm 12
kg
2.7
Stanley
/
( ) ( )
1.
a.
b. (
)
c.
2.
a.
b.
(
)
c.
d.
e.
f.
(RCD)
RCD
3.
a.
b.
(
)
c. /
d.
e.
f.
g.
4.
a.
b.
c.
/
d.
繁體中文
1 2
e.
f.
g.
5.
a.
( )
( )
/
( )
Stanley
A.
B.
C. /
D.
E.
F.
G.
H.
I. ( )
J. ( )
K.
L.
M.
N.
( 2)
2 (A)
繁體中文
1
3
( 2)
(A) (B)
( 3)
0
1.6 mm
P
/ (C) 0 1.6
mm
( )
( 456)
(C)
(D) 4
(E)
( 4 56)
( 78)
12 mm
( 7)
(9)
(H) (10)
( 8)
( 9)
(
)
a. (I) (F)
b.
(G)
( 10)
a. (J)
(F)
b. ( )
c.
(G)
( 11)
STEL630
( 11)
a. (K) (11a)
b. (11b)
(L)
c.
a. (1 1b)
b. (1 1a)
繁體中文
1 4
( 12)
(O)
( )
( 13)
a. 13
b.
c.
d.
( 14)
a. (L) (M)
(M)
b. (11d)
c. (1
1c)
d. (1
1e)
(11b) (11a)
( 15)
a. (N)
b.
c.
(L)
/
(
(MDF) )
Stanley
( 13)
繁體中文
1
5
Stanley
: ( )
: 120 4F
: 02-28201065
:
: 137
: 02-29994633
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Stanley STEL630 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で