Matrix CXC 取扱説明書

CXMCXC

2

ENGLISH

繁體中文

日本語

󼨫󺈼󻪃

TIẾNG VIỆT





3

15

27

39

51

63

75

3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

• When using Matrix Cycles, basic precautions should always be followed, including the following: Read all instructions before using this equipment. It is

the responsibility of the owner to ensure that all users of this equipment are adequately informed of all warnings and precautions.

• This equipment is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating.

• Use this indoor cycle for its intended purpose as

described in this manual. Do not use attachments that

have not been recommended by the manufacturer.

• Never operate the indoor cycle if it is not working properly,

or if it has been damaged. Contact Customer Tech Support

or the authorized dealers for examination and repair.

• Do not use the indoor cycle without proper footwear.

NEVER operate the indoor cycle with bare feet.

• Do not wear any clothing that might catch on

any moving parts of this indoor cycle.

• Keep hands and feet clear at all times from moving parts

to avoid injury. Never turn the pedal cranks by hand.

• Do not dismount the indoor cycle until the

pedals are at a complete STOP.

• Do not insert any object, hands or feet into any openings,

or expose hands, arms or feet to the drive mechanism

or other potentially moving part of the indoor cycle.

• Do not use any equipment that is damaged or has worn

or broken parts. Use only replacement parts supplied

by Customer Tech Support or the authorized dealers.

• Do not operate where aerosol (spray) products are

being used or when oxygen is being administered.

• Close supervision is necessary when used near children.

• This equipment is not intended for use by persons with

reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

equipment by a person responsible for their safety.

• Ensure that adjustment levers (seat and handlebar

fore-and-aft) are properly secured and do not

interfere with range of motion during exercise.

• When adjusting the seat and handlebar height,

hold the seat or handlebar with one hand,

while lifting and then locking the lever. Ensure

clamp is fully engaged prior to use.

• Incorrect or excessive exercise may result in serious

injury or death. If you experience any kind of pain,

including but not limited to chest pains, nausea, dizziness,

or shortness of breath, stop exercising immediately

and consult your physician before continuing.

• Do not jump on the unit.

• At no time should more than one person

be on unit while in operation.

• This unit should not be used by persons weighing

more than specied in the PRODUCT SPECIFICATIONS

SECTION. Failure to comply will void the warranty.

CAUTION!

CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE.

• It is essential that this equipment is used only indoors, in a climate controlled room. If this equipment has been exposed to colder temperatures or high moisture

climates, it is strongly recommended that the equipment is warmed up to room temperature and allowed time to dry out before rst time use.

WARNING!

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Do not use other attachments that are not recommended

by the manufacturer. Attachments may cause injury.

• To clean, wipe surfaces down with soap and slightly damp

cloth only; never use solvents. (See MAINTENANCE)

• At NO time should pets or children under the

age of 14 be closer to the unit than 10 feet.

• At NO time should children under the age of 14 use the unit.

• Children over the age of 14 should not use

the unit without adult supervision.

• Heart rate monitoring systems may be inaccurate.

• After exercising, push down on the brake lever to slow

the ywheel down and decrease the potential for injury.

• The indoor cycle does not have a independently

moving ywheel; the pedals will continue to move

together with the ywheel until the ywheel stops.

• Use the stationary training equipment

in a supervised environment.

ENGLISH

4

UNPACKING

Unpack the equipment where you will be using it. Place the carton

on a level at surface. It is recommended that you place a protective

covering on your oor. Never open box when it is on its side.

IMPORTANT NOTES

During each assembly step, ensure that ALL nuts

and bolts are in place and partially threaded.

Several parts have been pre-lubricated to aid in assembly

and usage. Please do not wipe this off. If you have diculty,

a light application of lithium grease is recommended.

WARNING!

There are several areas during the assembly process that

special attention must be paid. It is very important to follow

the assembly instructions correctly and to make sure all parts

are rmly tightened. If the assembly instructions are not

followed correctly, the equipment could have parts that are not

tightened and will seem loose and may cause irritating noises.

To prevent damage to the equipment, the assembly instructions

must be reviewed and corrective actions should be taken.

NEED HELP?

If you have questions or if there are any missing

parts, contact Customer Tech Support. Contact

information is located on the information card.

ASSEMBLY

TOOLS REQUIRED:

F 3 mm Allen Wrench

F 5 mm Allen Wrench

F 10 mm Allen Wrench

F Flat Wrench (15mm/17mm 325L)

F Phillips Screwdriver

PARTS INCLUDED:

F 1 Main Frame

F 1 Front Stabilizer Tube

F 1 Rear Stabilizer Tube

F 1 Handlebar Set

F 1 Transport Handle

F 1 Bicycle Saddle

F 2 Pedals

F 1 Console (CXM only)

F 1 Hardware Kit

CXC

CXM

SEAT AND HANDLEBARS: HOLD WITH ONE HAND WHILE

ADJUSTING HEIGHT. ENSURE CLAMP IS FULLY

ENGAGED PRIOR TO USE.

USE THE STATIONARY TRAINING EQUIPMENT IN A

SUPERVISED ENVIRONMENT UNDER THE DIRECT

SUPERVISION OF A TRAINED INSTRUCTOR.

SPINNING PEDALS CAN CAUSE INJURY.

THIS EXERCISE BICYCLE DOES NOT HAVE A

FREEWHEEL AND PEDAL SPEED MUST BE

REDUCED IN A CONTROLLED MANNER.

WARNING

KEEP CHILDREN UNDER THE AGE OF 14 AWAY FROM

EXERCISE EQUIPMENT.

ALL WARNINGS AND INSTRUCTIONS SHOULD BE READ

AND PROPER INSTRUCTION OBTAINED PRIOR TO USE.

USE THIS EQUIPMENT FOR ITS INTENDED PURPOSE

ONLY. CONSULT A PHYSICIAN BEFORE USING THIS

EQUIPMENT.

SET UP AND OPERATE THE STATIONARY EXERCISE

BICYCLE ON A SOLID LEVEL SURFACE. CARE

SHOULD BE TAKEN IN MOUNTING AND

DISMOUNTING THE STATIONARY EXERCISE

BICYCLE. BEFORE DISMOUNTING,

BRING THE PEDALS TO A

COMPLETE STOP.

CAUTION

SERIAL NUMBER

MODEL

F CXC MATRIX TARGET TRAINING CYCLE

F CXM MATRIX TARGET TRAINING CYCLE

* Use the information above when calling for service.

ENGLISH

5

TENSION CONTROL & EMERGENCY BRAKE LEVER

SADDLE

HORIZONTAL SADDLE

ADJUSTMENT LEVER

SADDLE HEIGHT

ADJUSTMENT LEVER

MAIN FRAME

SERVICE PANEL

FLYWHEEL

TRANSPORT HANDLE

REAR STABILIZER TUBE

HANDLEBARS

DEVICE HOLDER

(CXM has console)

WATER BOTTLE HOLDER

HORIZONTAL HANDLEBAR

ADJUSTMENT LEVER

HANDLEBAR HEIGHT

ADJUSTMENT LEVER

CRANK

PEDALS

TRANSPORT WHEELS

FRONT STABILIZER TUBE

LEVELERS

UNDER STABILIZER TUBES)

ENGLISH

6

1 2

CXC

CXM

A

B

C

B

Red Hardware Pack

Description Qty

A

B

C

Bolt (M12x25L)

Flat Washer

Bolt (M12x70L)

2

4

2

Torque Value

A

C

78 Nm / 58 ft-lb

E

D

F

Black (CXC) / Yellow (CXM)

Hardware Pack

Description Qty

D

E

F

Stopper

Screw (M8x20L)

Screw (M4x6L)

1

2

Torque Value

E 20 Nm / 14 ft-lb

Slide handlebars onto frame

before attaching (D), (E) and

then (F)

This part is for CXM only

CXM only: Push to lock

ENGLISH

7

H

1

2

3

G

CXC

CXM

4

ASSEMBLY COMPLETE!

3

LEFT

PEDAL

Green Hardware Pack

Description Qty

H Screw (M4x10L) 3

CXM

ENGLISH

Pre-installed Hardware

Description Qty

G Bolt (M6x50L) 1

Torque Value

100 Nm / 74 ft-lb

8

CXM

BACK-LIT LCD

Displays:

• Time

• RPM

• Watts

• Resistance Level

• MPH/KPH

• Distance

• Heart Rate (when heart

rate strap is worn)

• Calories

NAVIGATION ARROWS

CONFIRMATION KEY

CXM CONSOLE INFORMATION

Console turns on when pedals are moved.

Press

to change the large metric at the top from RPMs to

Watts, to HR, to a lap feature.

LAP/INTERVAL - when on the lap screen, press to start the rst

interval. Lap number, time and distance covered will be displayed.

Press to stop the interval. To start the next lap, press again,

etc. At the end of the workout, lap times/distances will be displayed.

SUMMARY SCREENS – after the workout is complete, an average

summary of RPM, Watts, MPH, HR, etc. will be displayed. Press

to

advance to the max summary screen for RPM, Watts MPH, HR, etc.

Press

again to advance to the Lap summary screen.

MANAGER MODE

To enter manager mode, press

simultaneously for 3-5

seconds, to exit manager mode, press and hold for 3-5 seconds.

• WORKOUT – set desired pause time and inactivity time

• USER – select weight

• UNIT – set console to display metric or imperial units

• SOFTWARE – version and updates

• FRAME LIFE – Accumulated distance and time

• MACHINE – Type, Serial Number, out of order

• LCD – adjust backlight brightness and contrast settings

• SHUTDOWN TIME – When in the workout summary, if there is

no RPM, this is the amount of time before the console shuts off

• PAIR HR – Disable / enable for ANT+/BLE heart rate pairing

screen

• ANT+ - enable or disable the broadcast function and set

broadcast ID

ENGLISH

9

CXM

USING THE HEART RATE FUNCTION

The heart rate function on this product is not a medical device. The heart rate reading

is intended only as an exercise aid in determining heart rate trends in general. Please

consult your physician.

When used in conjunction with a wireless chest transmitter (sold separately), your heart

rate can be transmitted wirelessly to the unit and displayed on the console. Compatible

with Bluetooth, ANT+ and Polar 5kHz heart rate devices.

NOTE: The chest strap must be tight and properly placed to receive an accurate and

consistent readout. If the chest strap is too loose, or positioned improperly, you may

receive an erratic or inconsistent heart rate readout.

WARNING!

Heart rate monitoring systems may be inaccurate. Over exercising may result in serious

injury or death. If you feel faint, stop exercising immediately.

BATTERY

When the battery is low, a low battery icon will be displayed in the upper right hand

corner of the screen.

The user will be prompted to pedal to charge (minimum of 67 RPMs). The battery icon will

disappear when sufficiently charged.

If the battery needs to be replaced, the console will display this message when necessary.

POWER ACCURACY

This bike displays power on the console. The power accuracy of this model has been

tested using the test method of ISO 20957-10:2017 to ensure a power accuracy within a

tolerance of ±10 % for input power ≥50 W, and within a tolerance of ±5 W for input power

<50 W. The power accuracy was verified using the following conditions:

Nominal Power Rotations per minute measured at crank

• 50 W 50 RPM

• 100 W 50 RPM

• 150 W 60 RPM

• 200 W 60 RPM

• 300 W 70 RPM

• 400 W 70 RPM

In addition to the above testing conditions, the manufacturer tested the power accuracy

at one additional point, using a crank rotation speed of approximately 80 RPM (or higher)

and comparing the displayed power to the input (measured) power.

ENGLISH

10

LEVELING THE EQUIPMENT

It is extremely important that the levelers are correctly

adjusted for proper operation. Turn leveling foot

clockwise to lower and counter-clockwise to raise unit.

Adjust each side as needed until the equipment is

level. An unbalanced unit may cause belt misalignment

or other issues. Use of a level is recommended.

BEFORE YOU BEGIN

LOCATION OF THE UNIT

Place the equipment on a level and stable surface away from direct sunlight. The

intense UV light can cause discoloration on the plastics. Locate your equipment in

an area with cool temperatures and low humidity. Please leave a clear zone on all

sides of the equipment that is at least 60 cm (23.6”). This zone must be clear of any

obstruction and provide the user a clear exit path from the machine. Do not place

the equipment in any area that will block any vent or air openings. The equipment

should not be located in a garage, covered patio, near water or outdoors.

PROPER USAGE

1. Sit on the cycle facing the handlebars. Both feet should

be on the floor one on each side of the frame.

2. To determine proper seat position, sit on the seat and position both feet on the

pedals. Your knee should bend slightly at the furthest pedal position. You should be

able to pedal without locking your knees or shifting your weight from side to side.

3. Adjust pedal straps to desired tightness.

4. To get off of the cycle, follow the proper usage steps in reverse.

WARNING!

Our equipment is heavy, use care and additional help if necessary when

moving. Failure to follow these instructions could result in injury.

TRAINING AREA

2 M

(78.7”)

0.56 M

(22.2”)

1.45 M

(57.2”)

FREE AREA

2 M

(78.7”)

1.76 M

(69.4”)

2.65 M

(104.4”)

ENGLISH

11

A

B

C

D

E

HOW TO ADJUST THE INDOOR CYCLE

The indoor cycle can be adjusted for maximum comfort and exercise

effectiveness. The instructions below describe one approach to adjusting

the indoor cycle to ensure optimal user comfort and ideal body

positioning; you may choose to adjust the indoor cycle differently.

SADDLE ADJUSTMENT

Proper saddle height helps ensure maximum exercise efficiency

and comfort, while reducing the risk of injury. Adjust the saddle

height to make sure it’s in proper position, one that keeps a slight

bend in your knee while your legs are in the extended position

HANDLEBAR ADJUSTMENT

Proper position for the handlebar is based primarily on comfort.

Typically, the handlebar should be positioned slightly higher

than the saddle for beginning cyclists. Advanced cyclists could try

different heights to get the arrangement most suitable for them.

A) SADDLE HORIZONTAL POSITION

Pull the adjustment lever down to slide the saddle forward

or backward as desired. Push the lever up to lock saddle

position. Test the saddle slide for proper operation.

B) SADDLE HEIGHT

Lift the adjustment lever up while sliding the saddle up and down

with the other hand. Push the lever down to lock saddle position.

C) HANDLEBAR HORIZONTAL POSITION

Pull the adjustment lever towards the rear of the cycle

to slide the handlebars forward or backward as desired.

Push the lever forward to lock handlebar position.

D) HANDLEBAR HEIGHT

Pull the adjustment lever up while raising or lowering the handlebar

with the other hand. Push the lever down to lock handlebar position.

E) PEDAL STRAPS

Place the ball of the foot into the toe cage until the ball of

the foot is centered over the pedal, reach down and pull

the pedal strap up to tighten prior to use. To remove your

foot from the toe cage, loosen the strap and pull out.

ENGLISH

12

RESISTANCE CONTROL / EMERGENCY BRAKE

The preferred level of difficulty in pedaling (resistance) can be regulated in fine increments by use of the

tension control lever. To increase the resistance, push the tension control lever towards the ground. To

decrease the resistance, pull up the lever upwards.

IMPORTANT:

• To stop the flywheel while pedaling, push down hard on the lever.

• The flywheel should quickly come to a complete stop.

• Make sure your shoes are fixed into the toe clip.

• Apply full resistance load when the bike is not in use to prevent injuries due to moving drive gear

components.

WARNING

The indoor cycle does not have a free moving flywheel; the pedals will continue to move

together with the flywheel until the flywheel stops. Reducing speed in a controlled

manner is required. To stop the flywheel immediately, push down the red emergency

brake lever. Always pedal in a controlled manner and adjust your desired cadence

according to your own abilities. Push the red lever down = emergency stop.

The indoor cycle uses a fixed flywheel that builds momentum and will keep the pedals

turning even after the user stops pedaling or if the user’s feet slip off. DO NOT ATTEMPT

TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL BOTH

THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these

instructions may lead to loss of control and the potential for serious injury.

ENGLISH

13

MAINTENANCE

1. Any and all part removal or replacement must be

performed by a qualied service technician.

2. DO NOT use any equipment that is damaged and or has worn or broken parts.

Use only replacement parts supplied by your country’s local MATRIX dealer.

3. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for

any reason. They contain important information. If unreadable or

missing, contact your MATRIX dealer for a replacement.

4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to

smooth operating equipment as well as keeping your liability to a

minimum. Equipment needs to be inspected at regular intervals.

5. Ensure that any person(s) making adjustments or performing maintenance

or repair of any kind is qualied to do so. MATRIX dealers will provide service

and maintenance training at our corporate facility upon request.

B

A

D

C

ENGLISH

MAINTENANCE SCHEDULE

ACTION FREQUENCY

Clean the indoor cycle using soft cloths or paper towels or other

Matrix approved solution (cleaning agents should be alcohol

and ammonia free). Disinfect the saddle and handlebars and

wipe off all bodily residues.

AFTER EACH USE

Make sure that the indoor cycle is level and does not rock. DAILY

Clean entire machine using water and a mild soap or other

Matrix approved solution (cleaning agents should be alcohol

and ammonia free).

Clean all exterior parts, the steel frame, front and rear

stabilizers, seat and handlebars.

WEEKLY

Test the emergency brake to make sure it is functioning

properly. To do this, press down the red emergency brake

lever while pedaling. When functioning properly, it should

immediately slow down the ywheel until it comes to a complete

stop.

BI-WEEKLY

Lubricate the saddle post (A). To do this, raise the saddle post to

the MAX position, spray with maintenance spray and rub down

the entire exterior surfaces with a soft cloth. Clean the saddle

slide (B) with a soft cloth and if necessary apply a small amount

of lithium/silicone grease.

BI-WEEKLY

Lubricate the handlebar post (C). To do this, raise the handlebar

post to the MAX position, spray with maintenance spray and

rub down the entire exterior surfaces with a soft cloth. Clean

the handlebar slide (D) with a soft cloth and if necessary apply a

small amount of lithium/silicone grease.

BI-WEEKLY

Inspect all assembly bolts and pedals on the machine for proper

tightness.

MONTHLY

Inspect handlebar and seat height adjustment levers for proper

tightness.

5 mm

MONTHLY

14

PRODUCT SPECIFICATIONS

CXM Indoor Cycle CXC Indoor Cycle

Console Back-lit LCD NA

Max User Weight 159 kg / 350 lbs

User Height Range 147 – 200.7 cm / 4’11” – 6’7”

Max Saddle and Handlebar Height 130.3 cm / 51.3”

Max Length 145.2 cm / 57.2”

Product Weight 56.5 kg / 124.6 lbs 55.2 kg / 121.7 lbs

Shipping Weight 62.4 kg / 137.6 lbs 61.1 kg / 134.7 lbs

Required Footprint (L x W)* 122.4 x 56.3 cm / 48.2” x 22.2”

Dimensions

(max saddle & handlebar height)

145.2 x 56.4 x 130.2 cm /

57.2” x 22.2 x 51.3”

145.2 x 56.4 x 130.2 cm /

57.2” x 22.2 x 51.3”

Overall Dimensions

(L x W x H)*

122.4 x 56.4 x 102.8 cm /

48.2” x 22.2 x 40.5”

122.4 x 56.4 x 102.8 cm /

48.2” x 22.2 x 40.5”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX equipment.

Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.

For most current owner’s manual and information, check www.matrixtness.com

ENGLISH

15

重要注意事項

請妥善保存這些說明書

• 使用 Matrix 健身車時，請務必遵行基本注意事項，包括下列要點：使用本器材前請閱讀所有使用說明。持有人應負責確保已充分告知本器材使用者所有警告與注意事項。

• 本器材適於商業環境用途。為確保您的安全並保護器材，使用前請閱讀所有說明。

• 請依照本手冊中說明的設計用途使用本室內健身車。請勿使用製

造商建議以外的配件。

• 若室內健身車無法正常運作或已損壞，切勿使用。請聯絡客戶技

術支援部門或授權經銷商進行檢查和維修。

• 使用室內健身車時請務必穿著合適的鞋類。切勿赤腳使用室內健

身車。

• 請勿穿著任何可能會勾住室內健身車上任何活動零件的衣物。

• 請隨時注意不要讓手腳觸碰到活動零件，以免受傷。不可徒手轉

動踏板曲柄。

• 請等待踏板完全停止之後再離開室內健身車。

• 切勿將任何物品或手腳放入任何開口處，手腳或手臂亦不可碰觸

室內健身車的傳動裝置或其他可能會移動的零件。

• 任何器材一旦損壞或零件磨損、破損，一律不得繼續使用。請使

用客戶技術支援部門或授權經銷商提供的替換零件。

• 使用氣霧 (噴霧) 產品時，或當氧氣受限情況下，請勿操作本器材。

• 若健身車所在位置附近有兒童，必須進行嚴密的監督。

• 本器材不適用於體能、知覺或精神機能不佳或欠缺經驗及知識的

人士；如欲使用，必須在他人監督下進行，且須由可負責其人身

安全者指導器材用途及使用方式。

• 確定所有調整桿 (座椅和前後把手) 皆牢牢固定，運動時的活動範

圍內不可有障礙物。

• 調整座椅和把手高度時，請用一手抓住座椅或把手，同時抬高並

鎖定調整桿。使用前，請確認固定把手已牢固。

• 錯誤運動方式和運動過量可能會導致嚴重受傷或死亡。若您感覺

各種不同的疼痛，包括胸痛、噁心、暈眩或呼吸困難等，應立即

停止運動並請教醫師此症狀之後，才可繼續使用。

• 請勿在本器材上跳躍。

• 運作中的器材僅限單人使用。

• 若體重超過產品規格章節所載重量，請勿使用本器材。未遵守規

定所導致的損害，皆不在保固範圍內。

注意！

請在使用本器材前詢問醫師。使用前請閱讀使用手冊。

• 本器材務必只能在可控制溫度的室內使用。若本器材曾暴露在低溫或高濕的環境下，強烈建議您在初次使用前先讓本器材暖機至符合室溫，或稍待一段時間等本器材變乾。

警告！

為降低燒燙傷、觸電或受傷的風險或人身傷害：

• 請勿使用製造商建議以外的其他配件。使用不當配件可能會導致

人身傷害。

• 清潔時，請使用肥皂及微濕的布擦拭器材表面，切勿使用溶

劑。(請參閱「保養」章節)

• 無論任何情況下，都不應該讓寵物或 14 歲以下兒童，接近本器

材周圍 3 公尺 (10 英尺) 內。

• 嚴禁未滿 14 歲的兒童使用本器材。

• 年滿 14 歲的兒童，必須有成人陪同監督才能使用本器材。

• 心率監測系統可能不準確。

• 運動完畢後，壓下煞車桿以減緩飛輪速度，並降低受傷風險。

• 室內健身車有慣性；踏板會繼續隨著飛輪一起移動，直到飛輪

停止。

• 請在受監督的環境下使用固定式訓練器材。

繁體中文

16

拆開包裝

在預定要使用本器材的地方拆封。請將紙箱放在平坦的表面上。建議您在地

板上鋪一層保護層。切勿在包裝箱側放的情況下打開包裝箱。

重要注意事項

在每個組裝步驟期間，請確認將所有螺帽和螺栓安裝在正確位置，並將其局

部旋緊。

部分零件有事先潤滑過，以方便您組裝和使用。請勿擦除潤滑油。如果組裝

有困難，建議您塗抹少量針車油。

警告！

組裝過程中有幾個部份須特別注意。請務必正確遵循組裝說明，以確認所有

零件均完全固定。若未確實遵照組裝說明可能會導致本器材的零件未鎖緊而

鬆脫，並發出擾人的噪音。為避免損壞器材，請務必詳閱組裝說明並予以

修正。

需要協助嗎？

如果有任何疑問或有缺少零件，請聯絡客戶技術支援部門。聯絡資訊位於資

訊卡上。

組裝

所需工具：

F 3 mm 內六角扳手

F 5 mm 內六角扳手

F 10 mm 內六角扳手

F 扁平扳手 (15 mm/17 mm 325L)

F 十字螺絲起子

隨附零件：

F 1 個主機架

F 1 個前貼地桿

F 1 個後貼地桿

F 1 套把手組

F 1 個運送把手

F 1 個健身車車座

F 2 個踏板

F 1 個儀表 (僅限 CXM)

F 1 套五金工具包

CX

CXM

座椅和把手：調整高度時，一手要

握住。使用前，請確認夾鉗已夾牢。

請在受過訓練的教練的直接指導

下，於受監督環境中使用本固定式

訓練器材。

旋轉中的踏板可能導致受傷。

本運動健身車有慣性，且踏板

速度必須在適度的控制範

圍內予以降低。

警告

請勿讓 14 歲以下的兒童接近本器

材。

使用前請詳閱所有警告及說明，並接

受正確的指導。請遵循本器材的用

途。請在使用本器材前詢問醫師。

請在穩固、平坦的地面上組裝與操

作本裝置。折收或展開本器材時

請小心謹慎。請等待踏板完全

靜止之後再離開健身車。

注意

序號

機型

F CXC MATRIX

室內健身車

F CXM MATRIX

室內健身車

* 報修時請提供以上資訊。

繁體中文

17

張力控制和緊急煞車桿

車座

車座水平調整桿

車座高度調整桿

主機架

維修面板

飛輪

運送把手

後貼地桿

把手

裝置架

(CXM 配備儀表)

水壺架

把手水平調整桿

把手高度調整桿

曲柄

踏板

移動輪

前貼地桿

水平儀

(貼地桿下方)

繁體中文

18

1 2

CXC

CXM

A

B

C

B

紅色五金包

說明數量

A

B

C

螺栓 (M12x25L)

平墊圈

螺栓 (M12x70L)

2

4

2

扭力值

A

C

78 Nm / 58 ft-lb

E

D

F

黑色 (CXC) / 黃色 (CXM)

五金包

說明數量

D

E

F

止動器

螺絲 (M8x20L)

螺絲 (M4x6L)

1

2

扭力值

E 20 Nm / 14 ft-lb

依序連接 (D)、(E) 和 (F) 之前，

請先將把手推至機架適當位置。

此零件僅限 CXM

僅限 CXM：推動後鎖定

繁體中文

19

H

1

2

3

G

CXC

CXM

4

組裝完成！

3

左

踏板

綠色五金包

說明數量

H 螺絲 (M4x10L) 3

CXM

繁體中文

預先安裝硬體

詳述數量

G 中心螺絲（M6x50L） 1

轉矩值

100 牛頓米 / 74 ft-lb

20

CXM

繁體中文

背光 LCD

顯示：

• 時間

• RPM

• 瓦特值

• 阻力等級

• MPH/KPH

• 距離

• 心率 (配戴心率監測帶時)

• 卡路里

瀏覽箭頭

確認鍵

CXM 儀表資訊

儀表會在踏板移動時開啟。

按下

，將頂端的較大單位從 RPM 變更為瓦特值、心率或圈數功

能。

圈數/間歇 – 顯示圈數畫面時，按下開始第一個間歇。相應圈數、時間

和距離將會顯示。按下停止間歇。如需開始下一圈，再次按下。鍛

鍊結束時，將會顯示圈數/距離。

摘要畫面 – 鍛鍊完成後，將會顯示 RPM、瓦特值、MPH、心率等數據的平

均值摘要。按下

，進入 RPM、瓦特值、MPH、心率等數據的最大值摘

要畫面。再次按下

，進入圈數摘要畫面。

管理員模式

如需進入管理員模式，同時按下

3-5 秒；如需退出管理員模式，請

按住 3-5 秒。

• 鍛鍊 (WORKOUT) – 設定所需的暫停時間和閒置時間

• 使用者 (USER) – 選擇體重

• 單位 (UNIT) – 設定儀表以顯示公制或英制單位

• 軟體 (SOFTWARE) – 版本與更新

• 機架壽命 (FRAME LIFE) – 累計距離與時間

• 機器 (MACHINE) – 類型、序號、故障

• LCD – 調整背光亮度和對比設定

• 關機時間 (SHUTDOWN TIME) – 檢視鍛鍊成績報告時，若無 RPM，

即代表關閉儀表前的時間量

• 連線心率 (PAIR HR) – 禁用/启用ANT + / BLE心率配对屏幕

• ANT+ – 啟用或停用廣播功能，並設定廣播 ID

ページが読み込まれています...

Matrix CXC 取扱説明書

このマニュアルも適しています

Matrix CXC 取扱説明書

関連論文

その他のドキュメント