Matrix CXP 取扱説明書

CXP

2

3

16

29

42

55

68

81

ENGLISH

繁體中文

日本語

한국어

TIẾNG VIỆT





3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

• When using Matrix Cycles, basic precautions should always be followed, including the following: Read all instructions before using this equipment. It is

the responsibility of the owner to ensure that all users of this equipment are adequately informed of all warnings and precautions.

• This equipment is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating.

• Use this indoor cycle for its intended purpose as

described in this manual. Do not use attachments that

have not been recommended by the manufacturer.

• Never operate the indoor cycle if it is not working properly,

or if it has been damaged. Contact Customer Tech Support

or the authorized dealers for examination and repair.

• Do not use the indoor cycle without proper footwear.

NEVER operate the indoor cycle with bare feet.

• Do not wear any clothing that might catch on

any moving parts of this indoor cycle.

• Keep hands and feet clear at all times from moving parts

to avoid injury. Never turn the pedal cranks by hand.

• Do not dismount the indoor cycle until the

pedals are at a complete STOP.

• Do not insert any object, hands or feet into any openings,

or expose hands, arms or feet to the drive mechanism

or other potentially moving part of the indoor cycle.

• Do not use any equipment that is damaged or has worn

or broken parts. Use only replacement parts supplied

by Customer Tech Support or the authorized dealers.

• Do not operate where aerosol (spray) products are

being used or when oxygen is being administered.

• Close supervision is necessary when used near children.

• This equipment is not intended for use by persons with

reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

equipment by a person responsible for their safety.

• Ensure that adjustment levers (seat and handlebar

fore-and-aft) are properly secured and do not

interfere with range of motion during exercise.

• When adjusting the seat and handlebar height,

hold the seat or handlebar with one hand,

while lifting and then locking the lever. Ensure

clamp is fully engaged prior to use.

• Incorrect or excessive exercise may result in serious

injury or death. If you experience any kind of pain,

including but not limited to chest pains, nausea, dizziness,

or shortness of breath, stop exercising immediately

and consult your physician before continuing.

• Do not jump on the unit.

• At no time should more than one person

be on unit while in operation.

• This unit should not be used by persons weighing

more than specied in the PRODUCT SPECIFICATIONS

SECTION. Failure to comply will void the warranty.

CAUTION!

CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE.

• It is essential that this equipment is used only indoors, in a climate controlled room. If this equipment has been exposed to colder temperatures or high moisture

climates, it is strongly recommended that the equipment is warmed up to room temperature and allowed time to dry out before rst time use.

WARNING!

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Do not use other attachments that are not recommended

by the manufacturer. Attachments may cause injury.

• To clean, wipe surfaces down with soap and slightly damp

cloth only; never use solvents. (See MAINTENANCE)

• At NO time should pets or children under the

age of 14 be closer to the unit than 10 feet.

• At NO time should children under the age of 14 use the unit.

• Children over the age of 14 should not use

the unit without adult supervision.

• Heart rate monitoring systems may be inaccurate.

• After exercising, push down on the brake lever to slow

the ywheel down and decrease the potential for injury.

• The indoor cycle does not have a independently

moving ywheel; the pedals will continue to move

together with the ywheel until the ywheel stops.

• Use the stationary training equipment

in a supervised environment.

ENGLISH

4

UNPACKING

Unpack the equipment where you will be using it. Place the carton

on a level at surface. It is recommended that you place a protective

covering on your oor. Never open box when it is on its side.

IMPORTANT NOTES

During each assembly step, ensure that ALL nuts

and bolts are in place and partially threaded.

Several parts have been pre-lubricated to aid in assembly

and usage. Please do not wipe this off. If you have diculty,

a light application of lithium grease is recommended.

WARNING!

There are several areas during the assembly process that

special attention must be paid. It is very important to follow

the assembly instructions correctly and to make sure all parts

are rmly tightened. If the assembly instructions are not

followed correctly, the equipment could have parts that are not

tightened and will seem loose and may cause irritating noises.

To prevent damage to the equipment, the assembly instructions

must be reviewed and corrective actions should be taken.

NEED HELP?

If you have questions or if there are any missing

parts, contact Customer Tech Support. Contact

information is located on the information card.

ASSEMBLY

TOOLS REQUIRED:

F 3 mm Allen Wrench

F 5 mm Allen Wrench

F 10 mm Allen Wrench

F Flat Wrench (15mm/17mm 325L)

F Phillips Screwdriver

PARTS INCLUDED:

F 1 Main Frame

F 1 Front Stabilizer Tube

F 1 Rear Stabilizer Tube

F 1 Handlebar Set

F 1 Transport Handle

F 1 Bicycle Saddle

F 2 Pedals

F 1 Console

F 1 Hardware Kit

SEAT AND HANDLEBARS: HOLD WITH ONE HAND WHILE

ADJUSTING HEIGHT. ENSURE CLAMP IS FULLY

ENGAGED PRIOR TO USE.

USE THE STATIONARY TRAINING EQUIPMENT IN A

SUPERVISED ENVIRONMENT UNDER THE DIRECT

SUPERVISION OF A TRAINED INSTRUCTOR.

SPINNING PEDALS CAN CAUSE INJURY.

THIS EXERCISE BICYCLE DOES NOT HAVE A

FREEWHEEL AND PEDAL SPEED MUST BE

REDUCED IN A CONTROLLED MANNER.

WARNING

KEEP CHILDREN UNDER THE AGE OF 14 AWAY FROM

EXERCISE EQUIPMENT.

ALL WARNINGS AND INSTRUCTIONS SHOULD BE READ

AND PROPER INSTRUCTION OBTAINED PRIOR TO USE.

USE THIS EQUIPMENT FOR ITS INTENDED PURPOSE

ONLY. CONSULT A PHYSICIAN BEFORE USING THIS

EQUIPMENT.

SET UP AND OPERATE THE STATIONARY EXERCISE

BICYCLE ON A SOLID LEVEL SURFACE. CARE

SHOULD BE TAKEN IN MOUNTING AND

DISMOUNTING THE STATIONARY EXERCISE

BICYCLE. BEFORE DISMOUNTING,

BRING THE PEDALS TO A

COMPLETE STOP.

CAUTION

SERIAL NUMBER

MODEL: CXP MATRIX TARGET TRAINING CYCLE

* Use the information above when calling for service.

ENGLISH

5

TENSION CONTROL & EMERGENCY BRAKE LEVER

SADDLE

HORIZONTAL SADDLE

ADJUSTMENT LEVER

SADDLE HEIGHT

ADJUSTMENT LEVER

MAIN FRAME

SERVICE PANEL

FLYWHEEL

TRANSPORT HANDLE

REAR STABILIZER TUBE

HANDLEBARS

CONSOLE

WATER BOTTLE HOLDER

HORIZONTAL HANDLEBAR

ADJUSTMENT LEVER

HANDLEBAR HEIGHT

ADJUSTMENT LEVER

PEDALS

CRANK

TRANSPORT WHEELS

FRONT STABILIZER TUBE

LEVELERS

ENGLISH

6

1 2

A

B

C

B

Red Hardware Pack

Description Qty

A

B

C

Bolt (M12x25L)

Flat Washer

Bolt (M12x70L)

2

4

2

Torque Value

A

C

78 Nm / 58 ft-lb

E

F

D

Yellow Hardware Pack

Description Qty

D

E

F

Stopper

Screw (M8x20L)

Screw (M4x6L)

1

2

Torque Value

E 20 Nm / 14 ft-lb

Push to lock

ENGLISH

7

H

1

2

3

G

4

ASSEMBLY COMPLETE!

3

Pre-installed Hardware

Description Qty

G Bolt (M6x50L) 1

Torque Value

100 Nm / 74 ft-lb

LEFT PEDAL

Green Hardware Pack

Description Qty

H Screw (M4x10L) 3

ENGLISH

8

HOME SCREEN RUN SCREEN (RPM)

A

I

E

H

B

F

J

C

G

D

ENGLISH

9

The CXP has a fully integrated touch screen display. All information required for

workouts is explained on screen. Exploration of the interface is highly encouraged.

A) POWER BUTTON: Press to wake display/power on. Press and hold for 3 seconds

to put display to sleep. Press and hold for 10 seconds to power off.

B) LANGUAGE SELECTION

C) CLOCK

D) MENU: Touch to access various functions before or during your workout.

E) WORKOUTS: Touch to access a variety of target training options or preset

workouts.

F) SIGN IN: Touch to sign in using your XID (WiFi is an optional add-on feature).

G) CURRENT SCREEN: Displays what screen you are currently viewing.

H) FEEDBACK WINDOWS: Displays Time, RPM, Watts, Average Watts, Speed, Heart

Rate (BPM), Level, Pace, Distance or Calories. Feedback varies based on current

screen.

I) CHANGE SCREEN: Swipe display left or right to cycle between 6 different run

screen options. Or select a metric with an orange triangle to go straight to a

desired screen.

J) TARGET TRAINING SCREEN: Press to return to target training screen when a

target training options has been set. Press the target icon to set a specific training

goal and activate the LED color wrap.

• PERSONAL INFO: Enter weight, age and gender to ensure caloric data and the

power-to-weight ratio is more accurate.

• BATTERY: Battery level is shown at the bottom of the MENU screen. Pedaling

can wake/power on the console. Pedaling at a rate above 77 RPM will charge the

battery.

HOME SCREEN

• Pedal to START immediately. Or...

• Touch the WORKOUTS button to customize your workout.

• Touch the SIGN IN button to sign in using your XID.

CONSOLE OPERATION

SIGN IN

1) Enter your XID and touch .

2) Enter your PASSCODE and touch .

Consoles equipped with RFID will support logging in with RFID tag. To

log in, touch your RFID tag to the right side surface of the console.

REGISTER A NEW USER

1) Don’t have an xID account? Registration is easy.

2) Follow the on-screen prompts to create your free account.

3) Review your information and select the I ACCEPT THE TERMS AND

CONDITIONS box to review the Terms and Conditions.

4) Touch to complete registration. Your account

is now active and you are signed-in.

WORKOUT SETUP

1) After touching the WORKOUTS button, select

one of the WORKOUTS from the list.

2) Use the SLIDER CONTROLS to adjust your program settings.

3) Press GO to begin your workout.

CHANGE WORKOUT

During a workout, touch

and then touch CHOOSE

EXERCISE to access available workouts.

SUMMARY SCREENS

After your workout is complete, a workout summary will appear. You

can swipe up and down to scroll through the summary. Also, swipe the

display left and right to switch between the summary screens.

COOL DOWN

Touch START COOL DOWN to enter cool down mode. Cool down lasts for

a few minutes while reducing the workout intensity, allowing your body to

recover from your workout. End cool down to go to workout summary.

ENGLISH

10

WIRELESS HEART RATE

To connect your ANT+ or Bluetooth SMART heart rate device to the

console, touch

and then touch HEART RATE DEVICE PAIRING.

The heart rate function on this product is not a medical device. The heart rate reading is

intended only as an exercise aid in determining heart rate trends in general. Please consult

your physician.

When used in conjunction with a wireless chest strap or arm band, your heart rate can be

transmitted wirelessly to the unit and displayed on the console.

WARNING!

Heart rate monitoring systems may be inaccurate. Over exercising may result

in serious injury or death. If you feel faint, stop exercising immediately.

* Supported standards with carrier frequency of 13.56 MHz include; ISO 14443 A, ISO 15693, ISO 14443 B, Sony Felica, Inside Contact-less (HID iClass), and LEGIC RF.

TARGET TRAINING WORKOUT

1) Start pedaling until the default screen appears.

2) Either swipe right or tap the metric box with an orange triangle to take you

directly to the desired screen.

3) Once on your desired screen, tap the large metric or the target icon to set your

training goal and then touch . The LED lights now become associated to that

target.

LED LIGHTS

Target training programming uses bright color lights on the top and sides of the

console to gauge effort and keep everyone on track of their goals. These lights may

be turned on or off in the workout setup by pressing LIGHTS ON or LIGHTS OFF. The

color indicators are: BLUE = below target, GREEN = on target, RED = above target.

MANAGER MODE

To enter manager mode, press and hold the MATRIX logo in the center of the screen

for 10 seconds. Then enter 1001 and touch .

POWER ACCURACY

This bike displays power on the console. The power accuracy of this model has been

tested using the test method of ISO 20957-10:2017 to ensure a power accuracy within a

tolerance of ±10 % for input power ≥50 W, and within a tolerance of ±5 W for input power

<50 W. The power accuracy was verified using the following conditions:

Nominal Power Rotations per minute measured at crank

• 50 W 50 RPM

• 100 W 50 RPM

• 150 W 60 RPM

• 200 W 60 RPM

• 300 W 70 RPM

• 400 W 70 RPM

In addition to the above testing conditions, the manufacturer tested the power accuracy

at one additional point, using a crank rotation speed of approximately 80 RPM (or higher)

and comparing the displayed power to the input (measured) power.

CONSOLE OPERATION

ENGLISH

11

LEVELING THE EQUIPMENT

It is extremely important that the levelers are correctly

adjusted for proper operation. Turn leveling foot

clockwise to lower and counter-clockwise to raise unit.

Adjust each side as needed until the equipment is

level. An unbalanced unit may cause belt misalignment

or other issues. Use of a level is recommended.

BEFORE YOU BEGIN

LOCATION OF THE UNIT

Place the equipment on a level and stable surface away from direct sunlight. The

intense UV light can cause discoloration on the plastics. Locate your equipment in

an area with cool temperatures and low humidity. Please leave a clear zone on all

sides of the equipment that is at least 60 cm (23.6”). This zone must be clear of any

obstruction and provide the user a clear exit path from the machine. Do not place

the equipment in any area that will block any vent or air openings. The equipment

should not be located in a garage, covered patio, near water or outdoors.

WARNING!

Our equipment is heavy, use care and additional help if necessary when

moving. Failure to follow these instructions could result in injury.

PROPER USAGE

1. Sit on the cycle facing the handlebars.

Both feet should be on the floor

one on each side of the frame.

2. To determine proper seat position, sit on

the seat and position both feet on the

pedals. Your knee should bend slightly at

the furthest pedal position. You should be

able to pedal without locking your knees or

shifting your weight from side to side.

3. Adjust pedal straps to desired tightness.

4. To get off of the cycle, follow the

proper usage steps in reverse.

TRAINING AREA

2 M

(78.7”)

0.56 M

(22.2”)

1.45 M

(57.2”)

FREE AREA

2 M

(78.7”)

1.76 M

(69.4”)

2.65 M

(104.4”)

ENGLISH

12

ENGLISH

A

B

C

D

E

HOW TO ADJUST THE INDOOR CYCLE

The indoor cycle can be adjusted for maximum comfort and exercise

effectiveness. The instructions below describe one approach to adjusting

the indoor cycle to ensure optimal user comfort and ideal body

positioning; you may choose to adjust the indoor cycle differently.

SADDLE ADJUSTMENT

Proper saddle height helps ensure maximum exercise efficiency

and comfort, while reducing the risk of injury. Adjust the saddle

height to make sure it’s in proper position, one that keeps a slight

bend in your knee while your legs are in the extended position

HANDLEBAR ADJUSTMENT

Proper position for the handlebar is based primarily on comfort.

Typically, the handlebar should be positioned slightly higher

than the saddle for beginning cyclists. Advanced cyclists could try

different heights to get the arrangement most suitable for them.

A) SADDLE HORIZONTAL POSITION

Pull the adjustment lever down to slide the saddle forward

or backward as desired. Push the lever up to lock saddle

position. Test the saddle slide for proper operation.

B) SADDLE HEIGHT

Lift the adjustment lever up while sliding the saddle up and down

with the other hand. Push the lever down to lock saddle position.

C) HANDLEBAR HORIZONTAL POSITION

Pull the adjustment lever towards the rear of the cycle

to slide the handlebars forward or backward as desired.

Push the lever forward to lock handlebar position.

D) HANDLEBAR HEIGHT

Pull the adjustment lever up while raising or lowering the handlebar

with the other hand. Push the lever down to lock handlebar position.

E) PEDAL STRAPS

Place the ball of the foot into the toe cage until the ball of

the foot is centered over the pedal, reach down and pull

the pedal strap up to tighten prior to use. To remove your

foot from the toe cage, loosen the strap and pull out.

13

RESISTANCE CONTROL / EMERGENCY BRAKE

The preferred level of difficulty in pedaling (resistance) can be regulated in fine increments by use of the

tension control lever. To increase the resistance, push the tension control lever towards the ground. To

decrease the resistance, pull up the lever upwards.

IMPORTANT:

• To stop the flywheel while pedaling, push down hard on the lever.

• The flywheel should quickly come to a complete stop.

• Make sure your shoes are fixed into the toe clip.

• Apply full resistance load when the bike is not in use to prevent injuries due to moving drive gear

components.

WARNING

The indoor cycle does not have a free moving flywheel; the pedals will continue to move

together with the flywheel until the flywheel stops. Reducing speed in a controlled

manner is required. To stop the flywheel immediately, push down the red emergency

brake lever. Always pedal in a controlled manner and adjust your desired cadence

according to your own abilities. Push the red lever down = emergency stop.

The indoor cycle uses a fixed flywheel that builds momentum and will keep the pedals

turning even after the user stops pedaling or if the user’s feet slip off. DO NOT ATTEMPT

TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL BOTH

THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these

instructions may lead to loss of control and the potential for serious injury.

ENGLISH

14

ENGLISH

MAINTENANCE SCHEDULE

ACTION FREQUENCY

Clean the indoor cycle using soft cloths or paper towels or other

Matrix approved solution (cleaning agents should be alcohol

and ammonia free). Disinfect the saddle and handlebars and

wipe off all bodily residues.

AFTER EACH USE

Make sure that the indoor cycle is level and does not rock. DAILY

Clean entire machine using water and a mild soap or other

Matrix approved solution (cleaning agents should be alcohol

and ammonia free).

Clean all exterior parts, the steel frame, front and rear

stabilizers, seat and handlebars.

WEEKLY

Test the emergency brake to make sure it is functioning

properly. To do this, press down the red emergency brake

lever while pedaling. When functioning properly, it should

immediately slow down the ywheel until it comes to a complete

stop.

BI-WEEKLY

Lubricate the saddle post (A). To do this, raise the saddle post to

the MAX position, spray with maintenance spray and rub down

the entire exterior surfaces with a soft cloth. Clean the saddle

slide (B) with a soft cloth and if necessary apply a small amount

of lithium/silicone grease.

BI-WEEKLY

Lubricate the handlebar post (C). To do this, raise the handlebar

post to the MAX position, spray with maintenance spray and

rub down the entire exterior surfaces with a soft cloth. Clean

the handlebar slide (D) with a soft cloth and if necessary apply a

small amount of lithium/silicone grease.

BI-WEEKLY

Inspect all assembly bolts and pedals on the machine for proper

tightness.

MONTHLY

Inspect handlebar and seat height adjustment levers for proper

tightness.

5 mm

MONTHLY

MAINTENANCE

1. Any and all part removal or replacement must be

performed by a qualied service technician.

2. DO NOT use any equipment that is damaged and or has worn or broken parts.

Use only replacement parts supplied by your country’s local MATRIX dealer.

3. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for

any reason. They contain important information. If unreadable or

missing, contact your MATRIX dealer for a replacement.

4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to

smooth operating equipment as well as keeping your liability to a

minimum. Equipment needs to be inspected at regular intervals.

5. Ensure that any person(s) making adjustments or performing maintenance

or repair of any kind is qualied to do so. MATRIX dealers will provide service

and maintenance training at our corporate facility upon request.

B

A

D

C

15

PRODUCT SPECIFICATIONS

CXP Indoor Cycle

Max User Weight 159 kg / 350 lbs

User Height Range 147 – 200.7 cm / 4’11” – 6’7”

Max Saddle and Handlebar Height 130.3 cm / 51.3”

Max Length 145.2 cm / 57.2”

Product Weight 57.6 kg / 127 lbs

Shipping Weight 63.5 kg / 140 lbs

Required Footprint (L x W)* 122.4 x 56.3 cm / 48.2” x 22.2”

Dimensions

(max saddle & handlebar height)

145.2 x 56.4 x 130.2 cm /

57.2” x 22.2 x 51.3”

Overall Dimensions

(L x W x H)*

122.4 x 56.4 x 102.8 cm /

48.2” x 22.2 x 40.5”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX equipment.

Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.

For most current owner’s manual and information, check www.matrixtness.com

NOTE:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate this equipment.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with a minimum distance

of 20 centimeters between the radiator and your body

ENGLISH

16

重要預防措施

保存以下說明

y使用 Matrix Cycles 時，請務必隨時遵守基本預防措施，包含以下：使用設備前，詳盡閱讀說明。設備持有者有責任確定所有使用者皆明確瞭解所有警告和預防措施。

y本設備以商業用途為目的。為確保您的安全與保護設備，操作前請詳盡閱讀說明。

y請將此飛輪健身車用於本手冊中所述之預期

用途。請勿使用非製造商推薦之附件。

y倘飛輪健身車無法正常運轉或者已損壞，請勿操作。

請連絡客戶技術支援或已授權經銷商檢查與維修。

y若未穿著合適的鞋子，請勿使用飛輪健身車。

切勿赤腳操作飛輪健身車。

y請勿穿著任何可能會碰到本室內健

身車任何活動零件之衣物。

y手腳隨時與活動零件保持距離，以免

受傷。切勿用手轉動踏板曲柄。

y在踏板完全靜止前，請勿下車。

y請勿將任何物品、手或腳插入任何開口，或將手、手臂或腳

暴露在飛輪健身車的驅動機制或其他可能移動的部分。

y請勿使用任何已損壞、已磨損或故障的設備。僅能使

用客戶技術支援或授權經銷商提供的替換零件。

y請勿在使用氣溶膠（噴霧）產品或使用氧氣的地方操作。

y在兒童附近使用時，須嚴密監督。

y本設備不適合身體、感官或精神力下降以及缺乏

經驗和知識的人使用，除非有人能負責其安危，

並在他們監督或指引下使用本設備。

y確認調節桿（座椅和前後手把）正確固定，

不會影響運動時的動作範圍。

y調整座椅和手把高度時，用一隻手握住座椅或手把，

同時抬起然後鎖定槓桿。使用前請確認夾具完全嚙合。

y運動不正確或過度可能引致嚴重傷害事故或死亡。

倘您出現任何疼痛，包含但不限於胸痛、嘔吐、頭暈或呼

吸急促，請立即停止運動，並在繼續運動前諮詢您的醫生。

y請勿在設備上跳動。

y在機器運轉時的任何時間點，設備上都不應有超過一人。

y重量超過產品規格規定之人員不得使用本

機。未遵守本預防措施會導致保固失效。

y請勿使用非製造商推薦之其他附件。附件可能引致受傷。

警告！

使用設備前，請先諮詢醫師。使用前請先閱讀持有者手冊。

y本設備僅在氣候受到控制的室內使用。若此設備暴露在較冷的溫度或高濕度氣候下，大力建議將設備升溫至室溫，並在首次使用前保留機器乾燥時間。

警告！

為減少灼傷、火災、電擊或人身傷害之風險：

y清潔時只能用肥皂和微濕布擦拭表面，

切勿使用溶劑。（請參閱維修部分）

y任何時間寵物或14歲以下孩童都不該靠

近本設備10英呎（3公尺）以內。

y任何時間寵物或14歲以下孩童都不能使用本設備。

y14歲以上兒童需在成人指引下使用本設備。

y心跳速率監控系統可能會不準確。

y運動後，按下煞車桿使飛輪減速，以減少受傷的可能性。

y飛輪健身車沒有獨立移動的飛輪；

踏板將繼續與飛輪一起移動，直到飛輪停止。

y請在有人監督指導下使用固定訓練設備。

繁體中文

17

繁體中文

拆卸

在準備使用設備的場所拆卸包裝。將紙箱放置在水平表面上。

建議您先在地板上鋪設保護層。切勿在紙箱倒放時開箱。

重要訊息

在每個組裝步驟中，確認所有螺母和螺栓都已就位，且部分拴住。

部分零件已經事先潤滑，以便於組裝和使用。請勿將潤滑劑擦掉。

若遇到困難，建議您使用少量鋰基潤滑脂。

警告！

在組裝過程中有幾個區域須特別注意。務必正確遵循組裝

說明並確認所有零件牢固鎖緊。如未正確遵循組裝說明，

設備會有零件未鎖緊、看起來鬆動，並可能產生刺耳噪音。

為防止損壞設備，須詳閱組裝說明並採取正確措施。

需要幫助嗎？

若您有任何疑問或任何零件遺失，請連絡顧客

技術支援。連絡資訊記載於資訊卡上。

組裝

必備工具：

F 3毫米內六角扳手

F 5毫米內六角扳手

F 10毫米內六角扳手

F 扁平扳手（15毫米／17毫米 325L）

F 十字螺絲刀

零件包含：

F 1 主架構

F 1 前固定管

F 1 後固定管

F 1 手把組

F 1 滑輪握把

F 1 腳踏車座墊

F 2 踏板

F 1 控制台

F 1 硬體組

座椅和把手：調整高度時，一手要

握住。使用前，請確認夾鉗已夾牢。

請在受過訓練的教練的直接指導

下，於受監督環境中使用本固定式

訓練器材。

旋轉中的踏板可能導致受傷。

本運動健身車有慣性，且踏板

速度必須在適度的控制範

圍內予以降低。

警告

請勿讓 14 歲以下的兒童接近本器

材。

使用前請詳閱所有警告及說明，並接

受正確的指導。請遵循本器材的用

途。請在使用本器材前詢問醫師。

請在穩固、平坦的地面上組裝與操

作本裝置。折收或展開本器材時

請小心謹慎。請等待踏板完全

靜止之後再離開健身車。

注意

序號

機型：CXP MATRIX TARGET TRAINING CYCLE

* 撥打服務電話時請使用以上資訊。

18

張力控制與緊急煞車槓桿

座墊

水平座墊調整桿

座墊高度調整桿

主架構

服務面板

飛輪

滑輪握把

後固定管

手把

控制台

水壺放置架

水平握把調整桿

握把高度調整桿

踏板

曲柄

滑輪

前固定管

水平調桿

繁體中文

19

1 2

A

B

C

B

紅色硬體包

詳述數量

A

B

C

中心螺絲（M12x25L）

平墊圈

中心螺絲（M12x70L）

2

4

2

轉矩值

A

C

78 牛頓米 / 58 ft-lb

E

F

D

黃色硬體包

詳述數量

D

E

F

腳架

螺絲（ M8x20L）

螺絲（ M4x6L）

1

2

轉矩值

E 20 牛頓米 / 14 ft-lb

按壓鎖

繁體中文

20

H

1

2

3

G

4

組裝完成！

3

預先安裝硬體

詳述數量

G 中心螺絲（M6x50L） 1

轉矩值

100 牛頓米 / 74 ft-lb

左踏板

綠色硬體包

詳述數量

H 螺絲（ M4x10L） 3

繁體中文

ページが読み込まれています...

Matrix CXP 取扱説明書

Matrix CXP 取扱説明書

関連論文

その他のドキュメント